Characterization and adsorption properties of the chelating hydrogels derived from natural materials for possible use in the improvement of groundwater quality

A new carrageenan based chelating copolymer sorbent was prepared by gamma radiation induced copolymerization and crosslinking of kappa‐carrageenan (k‐Car) and acrylic acid (AAc). The swelling characteristics of the prepared copolymer were investigated by studying the effect of time, pH, and ionic strength of the swelling medium. The sorption capacities of the chelating copolymer for Fe, Pb, Mn, Zn, Cu, Sr, Cd, and Al were 172, 202, 202, 216, 221, 230, 239, and 244 mg/g respectively. The Freundlich and Langmuir adsorption isotherms were used to validate the metal uptake data and heats of adsorption for the investigated metal ions were calculated. The re‐use experiment showed that the prepared hydrogel could be regenerated upto at least 10 times. Because of the promising data collected from bench scale experiments, the prepared copolymer was examined as chelating sorbent to improve the quality of some groundwater resources. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Uptake of Pb2+ Using N-Vinyl Imidazole Based Uniform Porous Hydrogels

The uniform porous and continuous phase lead (II) adsorbent hydrogel, was prepared by copolymerizing 2-hydroxyethyl methacrylate (HEMA), acrylic acid (AAc), and N,N′-methylenebisacrylamide (MBAAm), with n-vinyl imidazole (VIM). A series of hydrogels, including different ratios of VIM, were prepared by photopolymerization and characterized. The influence of the uptake conditions such as pH, functional monomer percent, contact time, initial feed concentration, and foreign metal ions on the metal ion binding capacity of hydrogel, were also tested. The selective chelation of heavy metal ions from synthetic wastewater was also studied. The affinity order on molar basis was observed as follows: Pb (II) > Zn (II) > Cd (II). Chelation behavior of heavy metal ions could be modelled using both the Langmuir and Freundlich isotherms and it was seen that the Langmuir isotherm model was the best fit for the adsorption of Pb (II) ions in P(VIM/AAc/HEMA) hydrogel. Moreover, the limits of detection and the quantification values were determined. Regeneration of the hydrogels was easily performed with 1 M HCl and the same hydrogel can be reused five times almost without any loss of adsorption capacity. All these features make P(VIM/AAc/HEMA) hydrogels potential candidate adsorbent for heavy metal removal.     

Radiation synthesis and characterization of poly(N‐vinyl‐2‐pyrrolidone/acrylic acid) and poly(N‐vinyl‐2‐pyrrolidone/acrylamide) hydrogels for some metal‐ion separation

Two different hydrogels, prepared from N‐vinyl‐2‐pyrrolidone/acrylic acid (NVP/AAc) and N‐vinyl‐2‐pyrrolidone/acrylamide (NVP/AAm), were studied for the separation and extraction of some heavy‐metal ions from wastewater. The hydrogels were prepared by the γ‐radiation‐induced copolymerization of the aforementioned binary monomer mixtures. Further modification was carried out for the NVP/AAc copolymer through an alkaline treatment to improve the swelling behavior by the conversion of the carboxylic acid groups into its sodium salts. The thermal stability and swelling properties were also investigated as functions of the N‐vinyl‐2‐pyrrolidone content. The characterization and some selected properties of the prepared hydrogels were studied, and the possibility of their practical use in wastewater treatment for heavy metals such as Cu, Ni, Co, and Cr was investigated. The maximum uptake for a given metal was higher for a treated NVP/AAc hydrogel than for an untreated NVP/AAc hydrogel and was higher for an untreated NVP/AAc hydrogel than for an NVP/AAm hydrogel. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2642–2652, 2004     

Pectin‐[(3‐acrylamidopropyl) trimethylammonium chloride‐co‐acrylic acid] hydrogel prepared by gamma radiation and selectively silver (Ag) metal adsorption

Pectin‐[(3‐acrylamidopropyl) trimethylammonium chloride‐co‐acrylic acid] hydrogel has been prepared from the aqueous blend solution of pectin, (3‐acrylamidopropyl) trimethylammonium chloride (APTAC), and acrylic acid (AAc) by applying gamma radiation of different doses (1–25 kGy) from ⁶⁰Co gamma source. The hydrogels were characterized by equilibrium swelling, Fourier transform infrared, differential scanning calorimetry, and scanning electron microscopy. The hydrogels were used in multielement adsorption and it was found that pectin‐(APTAC‐co‐AAc) gel is highly selective toward silver (I) ion among 27 metal ions. The data obtained from equilibrium adsorption studies were fitted in Langmuir and Freundlich adsorption isotherm models and model parameters evaluated. The maximum adsorption capacity of pectin‐(APTAC‐co‐AAc) gel was found to be 67.6413 mg/g of dry gel at sample volume of 25 mL. The kinetic data were tested using pseudo‐first order and pseudo‐second order kinetic models and different adsorption diffusion models such as film diffusion and intra‐particle diffusivity model. Thiourea solution was used for desorption of adsorbed metal ions from the hydrogel. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45906.     

Equilibrium adsorption isotherm and controlled release of antibiotic drug chloroamphenicol from poly(2‐vinyl pyridine/acrylic acid) hydrogels prepared by gamma radiation

High water sorption of 2‐vinyl pyridine (2‐VP)/acrylic acid (AAc) hydrogel were prepared by free‐radical polymerization in aqueous solution of 2‐VP with AAc as comonomer. The amount of ionic monomer (AAc), the irradiation dose of prepared hydrogel, the pH, and the concentration of drug play an important factor on loading, adsorption, and releasing of water‐soluble chloroamphenicol drug. As a result of dynamic swilling tests, the effect of relative content of AAc on the swelling showed that it allowed a non‐Fickian type of water diffusion. The adsorption of the drug onto (2‐VP/AAc) hydrogels was studied by Freundlish adsorption isotherm. The drug concentrations showed an influence on the adsorption of drug which increased with increasing AAc content. From Freundlish adsorption isotherm, the empirical constants, k and n, can be evaluated and showed the ability of hydrogel to be loaded by the drug and the affinity of the drug to be uptake onto the hydrogel respectively. FTIR, TGA, and SEM techniques were used to study the characterization of hydrogel (2‐VP/AAc). Additionally, the release of the drug loaded from hydrogel discs was studied microbiologically to show that hydrophilic structure of the hydrogel has an antimicrobial effect as a dehydration of cytoplasm and unbalance of the cell wall functions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Reuse of a waste adsorbent poly(AAc/AM/SH)‐Cu superabsorbent hydrogel,for the potential phosphate ion removal from waste water: Matrix effects,adsorption kinetics,and thermodynamic studies

The most commonly applied methods for the treatment of used adsorbents is to recover them in acid/alkaline medium or direct enflame them. This work dealt with a new potential and economic method to utilize a waste adsorbent. Poly(AAc/AM/SH) superabsorbent hydrogels have proved to be a good adsorbent for Cu²⁺ ions and after adsorption the hydrogels were recovered in acid medium. In this report, the Cu²⁺ ion adsorbed hydrogel has not undergone any regeneration process and applied directly to phosphate ion adsorption. The Cu²⁺ ions‐loaded poly(AAc/AM/SH) hydrogels, were stable within a wide pH range and suitable for phosphate ion adsorption. The factors affecting the phosphate adsorption, such as pH, ionic strength, contact time, temperature, initial concentration of the phosphate ion, and coexisting ions were systematically investigated. The phosphate adsorption was highly pH dependent; and the maximum adsorption of 87.62 mg/g was achieved at pH 6.1. The adsorption data fitted the Langmuir adsorption isotherm better than the Freundlich isotherm. The concomitant anions show profounder adverse influence on phosphate ion adsorption of poly(AAc/AM/SH)‐Cu hydrogel and the effect follows the order citrate > sulfate > bicarbonate > chloride > nitrate. The thermodynamic parameters including ΔH°, ΔG°, and ΔS° for the adsorption processes of phosphate ions on the gel were also evaluated, and the negative ΔG° and ΔH° confirmed that the adsorption process was spontaneous and exothermic. The adsorption kinetic results suggest that the adsorption process was well described by the pseudo second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Radiation synthesis and application of a hydrogel based on acrylic acid and 2‐mercaptobenzimidazole

A hydrogel based on gamma‐radiation polymerization of acrylic acid (AAc) in the presence of 2‐mercaptobenzimidazole (MBI) and a crosslinking agent was prepared. The properties of this AAc/MBI hydrogel were characterized in terms of gel content, swelling in different solvents, structure morphology, and IR spectroscopy. Moreover, the thermal decomposition behavior of the prepared hydrogel was investigated by thermogravimetric analysis (TGA). The TGA thermograms were also used to determine the different kinetic parameters such as order of reaction and activation energy. The sorption of some divalent metal ions such as Cu²⁺, Pb²⁺, Cd²⁺, and Hg²⁺ by the AAc/MBI hydrogel also was studied. The results showed that the AAc/MBI hydrogel has a higher tendency to swell in water and polar solvents than in nonpolar solvents. The highest metal uptake by the hydrogel was found for Hg²⁺ and Cd²⁺, whereas the lowest was for Cu²⁺ and Pb²⁺ ions. The ratios between the distribution coefficients of the different metals [separation factors (SF)] indicate that the hydrogel has a high selectivity for Hg²⁺ over Cu²⁺ (SF = 10.923) and Pb²⁺ (SF = 19.110). However, the hydrogel prefers Hg²⁺ over Cd²⁺ (SF = 1.356) and showed a high selectivity for Cd²⁺ over Cu²⁺ (SF = 7.822) and Pb²⁺ (SF = 7.240). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1607–1614, 2002     

Removal of heavy metal ions from aqueous solutions by radiation‐induced chitosan/(acrylamidoglycolic acid‐co‐acrylic acid) magnetic nanopolymer

An effective method was developed to isolate toxic heavy metal ions from the aqueous solution by the magnetic nanopolymers. The magnetic sorbent was prepared with radiation‐induced crosslinking polymerization of chitosan (CS), 2‐acrylamido‐glycolic acid (AMGA), and acrylic acid (AAc), which stabilized by magnetite (Fe₃O₄) as nanoparticles. The formation of magnetic nanoparticles (MNPs) into the hydrogel networks was confirmed by Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, and Scanning electron microscopy, which revealed the formation of MNPs throughout the hydrogel networks. The swelling behavior of the hydrogels and magnetic ones was evaluated at different pH values. The adsorption activity for heavy metals such as Cu²⁺ and Co²⁺ by nonmagnetic and magnetic hydrogels, Fe₃O₄/CS/(AMGA‐co‐AAc), in terms of adsorption amount was studied. It was revealed that hydrogel networks with magnetic properties can effectively be used in the removal of heavy metal ions pollutants and provide advantageous over conventional ones. POLYM. ENG. SCI., 55:1441–1449, 2015. © 2015 Society of Plastics Engineers     

Construction of double cross-linked networks in calcium alginate/poly-N-isopropylacrylamide hydrogel with photothermal responsiveness for absorbing heavy metal ions

Hydrogels have been widely used for adsorbing heavy metal ions in wastewater treatment. Herein, a calcium alginate/poly-N-isopropylacrylamide double-network hydrogel with photothermal responsiveness was prepared for adsorbing heavy metal ions in aqueous solution. The chemical composition, micromorphology, swelling properties, photothermal responsiveness, adsorption properties, and adsorption mechanism of gel microspheres were studied, respectively. The gel microspheres had an interpenetrating three-dimensional porous structure, and their high porosity morphology and high specific surface area could ensure the adequate exposure of active adsorption sites. The gel microspheres showed excellent selective adsorption of Cr(III), and the theoretical maximum adsorption capacity of 146.16 mg/g was calculated according to the Langmuir model. Besides, its excellent photothermal conversion ability enhanced the resistance to external interference after the adsorption. Our work has provided an innovative approach to solar water purification while optimizing the preparation process.     

N-vinylpyrrolidone/acrylic acid/2-acrylamido-2-methylpropane sulfonic acid based hydrogels: Synthesis,characterization and their application in the removal of heavy metals

In this work, the synthesis of N-vinylpyrrolidone/acrylic acid/2-acrylamido-2-methylpropane sulfonic acid (NVP/AAc/AMPS) based hydrogels by UV-curing technique was studied and their swelling behavior, heavy metal ion recovery capabilities were investigated. The structures of hydrogels were characterized by FT-IR analysis and the results were consistent with the expected structures. Thermal gravimetric analysis of hydrogels showed that the thermal stability of hydrogel decreases slightly with incorporation of AMPS units into the structure. In addition, the morphology of the dry hydrogel sample was examined by SEM. According to swelling experiments, hydrogels with higher AMPS content gave relatively higher swelling ratio compared to neat hydrogel. These hydrogels were used for the separation of Cd(II), Cu(II) and Fe(III) ions from their aqueous solutions. The influence of the uptake conditions such as pH, time and initial feed concentration on the metal ion binding capacity of hydrogel was also tested. The selectivity of the hydrogel towards the different metal ions tested was Cd(II) > Cu(II) > Fe(III). It was observed that the specific interaction between metal ions and ionic co-monomers in the hydrogel affected the metal binding capacity of the hydrogel. The recovery of metal ions was also investigated in acid media.     

Cellulose-graft-polyacrylamide/hydroxyapatite composite hydrogel with possible application in removal of Cu (II) ions

Cellulose-graft-polyacrylamide/hydroxyapatite composite hydrogels of different weight ratios were prepared through a suspension polymerization method. Physical and chemical characteristics of the composite were investigated by Fourier transform infrared spectroscopy and scanning electron microscopy. The swelling behaviors of the composite hydrogels were investigated under varying conditions of time, temperature and pH. The optimized swelling capacity in standard conditions was found to be 5197% per gram of the hydrogel. The prepared hydrogel has the potential to be used for ion adsorption in water treatment. Such a possibility was examined through adsorption of copper (II) ions from an aqueous solution. The effects on adsorption of varying the time, pH, and initial concentration of copper (II) solution as well as some thermodynamic parameters were also investigated. The maximum adsorption capacity was found to be 175 mg per gram of composite hydrogel in dried state. The mechanism of adsorption was well presented using a pseudo-second-order kinetic model. Finally, the mercury-loaded hydrogel was regenerated without losing its original activity and stability.     

Gelatin based pH‐sensitive hydrogels for colon‐specific oral drug delivery: Synthesis,characterization, and in vitro release study

Based on gelatin (Gltn) and acrylic acid (AAc), biodegradable pH‐sensitive hydrogel was prepared using gamma radiation as super clean source for polymerization and crosslinking. Incorporation of PAAc in the prepared hydrogel was confirmed by Fourier transform infrared spectroscopy (FTIR). The effect of PAAc content on the morphological structure of the prepared hydrogel swollen at pH 1, 5, and 7 was examined using scanning electron microscopy (SEM). The results showed the dependence of the porous structure of the prepared hydrogels on AAc content and the pH of the swelling medium. Swelling properties of gelatin/acrylic acid copolymer hydrogels with different AAc contents were investigated at different pH values. Swelling data showed that the prepared hydrogels possessed pronounced pH sensitivity. In vitro release studies were performed to evaluate the hydrogel potential as drug carrier using ketoprofen as a model drug. Experimental data showed that the release profile depends on both hydrogel composition and pH of the releasing medium. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Photocatalytic Decolorization of Dye Effluent Using Radiation Developed Polymeric Nanocomposites

In this study [acrylic acid/p(N-vinyl-2-pyrrolidone)] (AAc/PVP) hydrogel was prepared using gamma irradiation technique. The prepared hydrogel was used as a template for in situ preparation of ZnO photocatalyst up to three deposition cycles. The structure, the thermal property, and the surface morphology of (AAc/PVP/ZnO) nanocomposite were characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), transmission electron microscope (TEM) and scanning electron microscope (SEM) techniques. The photocatalytic activity of the obtained nanocomposite was tested for the degradation of methyl blue dye (MB) in the aqueous medium using UV-light. The effect of operational parameters on the degradation of MB such as UV irradiation time, pH, and initial dye concentration were examined. It was found that complete decolorization of MB dye was achieved after 45 min at pH 4. The degradation rate fitted the pseudo-first-order model and the rate of the photocatalytic reaction of the first preparation cycle of ZnO was higher than that of the third preparation cycle.     

Preparation and characterisation of a poly(acrylamidoglycolic acid-co-acrylamide) hydrogel for selective binding of Cu and application to diffusive gradients in thin films measurements

A poly(acrylamidoglycolic acid-co-acrylamide) [poly(AAGA-co-AAm)] hydrogel was prepared by copolymerising 2-acrylamidoglycolic acid (AAGA) with acrylamide (AAm). The copolymer hydrogel composition and structure was characterised by FTIR spectroscopy and elemental microanalysis and found to contain 3.5 AAGA monomer units for each AAm monomer unit. This was similar to the monomer ratios used in the synthesis. The metal ion binding properties of the hydrogel were characterised for a range of metal ions (Cu²⁺, Cd²⁺, K⁺, Na⁺, Mg²⁺ and Ca²⁺) under varying conditions of pH, ionic strength, metal concentration and time. The hydrogel was shown to bind Cu²⁺ and Cd²⁺ strongly under non-competitive binding conditions, with binding capacities of 5.3 and 5.1 μmol cm⁻², respectively. The binding capacity of each metal decreased, under competitive binding conditions (with a range of metal ions present at 17.8 μN), to 1.3 and 0.17 μmol cm⁻², respectively, indicating stronger selectivity for Cu²⁺. The metal ions were readily recovered (>94%) by eluting with 2 M nitric acid solution for 24 h. The binding capacities for Cu²⁺ and Cd²⁺ were also found to decrease with increasing ionic strength and at pH values <5. The copolymer was found to have an equilibrium swelling ratio (q_w) of over 500 at a maxima of pH 5.4 and at low ionic strengths. Finally, the copolymer hydrogel was tested as a binding phase with the diffusive gradients in thin films technique. A linear mass vs. time relationship was observed for Cu²⁺ in synthetic Windermere water with a recovery of approximately 100%.     

Adsorptions of Some Heavy Metal Ions in Aqueous Solutions by Acrylamide/Maleic Acid Hydrogels

Abstract

In this study, acrylamide—maleic acid (AAm/MA) hydrogels in the form of rod have been prepared by γ-radiation. They have been used for adsorption of some heavy metal ions such as uranium, iron, and copper. For the hydrogel containing 40 mg of maleic acid and irradiated at 3.73 kGy, maximum and minimum swellings in the aqueous solutions of the heavy metal ions have been observed with water (1480%) and the aqueous solution of iron(III) nitrate (410%), respectively. Diffusions of water and heavy metal ions onto hydrogels have been found to be of the non-Fickian type of diffusion. In experiments of uranyl ions adsorption, Type II adsorption has been found. One gram of AAm/MA hydrogels sorbed 14–86 mg uranyl ions from solutions of uranyl acetate, 14–90 mg uranyl ions from solutions of uranyl nitrate, 16–39 mg iron ions from solutions of iron(IV) nitrate, and 28–81 mg copper ions from solutions of copper acetate, while acrylamide hydrogel did not sorb any heavy metals ions.     

Synthesis and characterization of hydrogels based on gamma irradiation of acrylic acid and methacrylic acid

In this work, hydrogels based on different ratios of acrylic acid (AAc) and methacrylic acid (MAc) monomers were prepared by gamma radiation copolymerization. The hydrogels were characterized by IR spectroscopy and thermogravimetric analysis (TGA). The effect of temperature and pH on the degree of swelling of AAc/MAc hydrogels was also studied. The results showed that the gel fraction of AAc is relatively higher than MAc, while the gel fraction of AAc/MAc hydrogels decreased slightly with increasing the ratio of MAc monomer in the initial solution. The IR spectroscopic analysis indicates the formation of copolymer networks and the presence of hydrogen bonding. The thermal study showed that PAAc hydrogel displayed higher thermal stability than PMAc and AAc/MAc hydrogels, over the studied compositions. The results showed that PAAc hydrogel reached equilibrium swelling state in water after 4 h, whereas PMAc and AAc/MAc hydrogels reached the equilibrium after 7 h. In this regard, AAc/MAc hydrogels showed degree of swelling in water lower than PAAc and higher than PMAc hydrogels. It was found that the swelling of the hydrogels based on AAc and MAc monomers or their copolymers increases with increasing temperature up to 50°C. Moreover, it was observed that the degree of swelling of hydrogels were not affected by increasing the pH values up to 4 and increased greatly within the pH values from 5 to 9. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Anionic/Cationic Membranes Obtained by a Radiation Grafting Method for Use in Waste Water Treatment

Investigations were carried out on different ionic membranes, which were prepared by radiation-induced graft copolymerization. Cationic (low density polyethylene (LPDE)-g-poly(acrylic acid) (PAAc)) and cationic/anionic (LDPE-g-P(AAc/4-vinyl pyridine (4VP)) membranes) were used to elucidate the possibility of their practical use. The metal uptake via their functional groups was determined by using atomic absorption and X-ray fluorescence. The amount of metal uptake by the prepared membranes increased significantly as the pH of the metal feed solution increased (pH ≤ 5·3) and the chelated metal ions were easily desorbed by treating the membrane with 0·1 M HCl for 2h at room temperature. The maximum uptake for a given metal was higher for the cationic/anionic membranes than for the cationic ones. The selectivity of the cationic/anionic membranes towards different metals was investigated using mixtures of two or three metals in the same feed solution. The membranes showed high selectivity towards Fe(III ) ions. Characterization of the graft copolymers containing metals was determined by thermogravimetric analysis (TGA) and X-ray diffraction (XRD). TGA results showed that the decomposition of the graft copolymer in the presence of chelated metal ion occurred at temperatures above 300°C. The XRD of LDPE-g-P(AAc/4VP) treated with Fe(III ) at various concentrations showed that the crystallinity decreased to a certain limiting value. The complexed copolymers could be recycled several times and showed high selectivity to the Fe(III ) ion in the presence of the other metal ions investigated. This may make such grafted membranes acceptable for practical use in waste water treatment. © 1997 SCI     

Removal of Cu2+ and Pb2+ ions from aqueous solutions by starch-graft-acrylic acid/montmorillonite superabsorbent nanocomposite hydrogels

In this study, the removal of copper(II) and lead(II) ions from aqueous solutions by Starch-graft-acrylic acid/montmorillonite (S-g-AA/MMT) nanocomposite hydrogels was investigated. For this purpose, various factors affecting the removal of heavy metal ions, such as treatment time with the solution, initial pH of the solution, initial metal ion concentration, and MMT content were investigated. The metal ion removal capacities of copolymers increased with increasing pH, and pH 4 was found to be the optimal pH value for maximum metal removal capacity. Adsorption data of the nanocomposite hydrogels were modeled by the pseudo-second-order kinetic equation in order to investigate heavy metal ions adsorption mechanism. The observed affinity order in competitive removal of heavy metals was found Cu²⁺ > Pb²⁺. The Freundlich equations were used to fit the equilibrium isotherms. The Freundlich adsorption law was applicable to be adsorption of metal ions onto nanocomposite hydrogel.     

Removal of Some Heavy Metal Ions Using Grafted Polyurethane Foam

Polyurethane (PU) was modified by grafting a mixture of two monomers acrylonitrile/acrylic acid (AN/AAc) by gamma irradiation method. Effects of various parameters such as, concentration of comonomer composition, grafting yield, gamma irradiation doses, dose rates and pH of adsorbent on the adsorption capacity were studied. Characterizations of the grafted polyurethane (PU-g-AN/AAc) were investigated using infrared (IR) spectroscopic analysis, X-ray diffraction (XRD) and scanning electron microscope (SEM). Moreover, the adsorption capacities of some heavy metals such as, Zn(II), Fe(II), Ca(II), Ni(II), Cu(II) and Pb(II) onto PU-foam and PU-g-AN/AAc were studied. The efficiency of such grafted polyurethane foams for uptaking different previous metal ions was determined and compared with that of natural granular activated carbon (GAC). The uptaking of metal ions was remarkably affected by the pH of the solution, the valances of metal ions, atomic weight and its initial concentrations. Equilibrium isotherms and interruptible diffusivities were investigated through batch experiments in analyzing the uptaking of aqueous solutions of metal ions onto PU foam, grafted PU, and granular activated carbon. The Frundlich constants k and 1/n have been determined for each metal ion to represent both the ability and the affinity of that ions towards the uptaking materials, respectively.     

Hydrogel beads based on carboxymethyl cellulose for removal heavy metal ions

Environment‐friendly carboxymethyl cellulose (CMC) hydrogel beads were successfully prepared using epichlorohydrin (ECH) as a crosslinking agent in the suspension of fluid wax. There was an ether linkage formed between ECH and CMC, which was identified from bands in FTIR spectra of the prepared hydrogel. The prepared hydrogel beads with diameters about 4 mm were apparently spherical and fully transparent. The X‐ray diffraction (XRD) spectra indicated that the adsorption of metal ion onto the oxygen atom of carboxyl group led to change in crystallinity patterns of hydrogels. The scanning electron microscope (SEM) images clearly showed that the hydrogels had an internal porous structure. The adsorption capacity increased as initial concentrations of metal ions and the pH value of metal ion solution increased. Freundlich and Langmuir isotherm models were employed to analyze the data from batch adsorption experiments. There are vey good correlation coefficients of linearized equations for Langmuir model, which indicated that the sorption isotherm of the hydrogel beads for metal ions can be fitted to the Langmuir model. The maximum adsorption amount of hydrogel beads for metal ions is 6.49, 4.06, and 5.15 mmol/g for Cu(II), Ni(II), and Pb(II), respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011