The effects of soft segments on the physical properties and water vapor permeability of H12MDI-PU cast films

This research was based on the study of the effects of H₁₂MDI-1, 4BD PU soft segments on the physical properties and water vapor permeability of films cast from solvent evaporation or wet coagulation method. The soft segments studied included polyether, polyester, and polycaprolactone polydiols. The NCO/OH mol ratios of prepolymer were prepared by 2, 3, 4, 5, and 8, respectively. The chain lengths of the soft segments used were: PTMG of molecular weights 650, 1000, 2000, and 2900; PBA of 1000, 2000, and 3000. The results revealed that the polyether-based PU cast films had lower T_gs than the polyester-based PU films. In general, the polyether-based PU films shows the characters of higher water vapor permeability, lower breaking elongation, and higher breaking strength. Films with higher molecular weight soft segments in the polymer chains exhibited lower T_gs, lower breaking strength, higher breaking elongation, and higher water vapor permeability. As the hard segment contents were increased, the films exhibited higher T_gs. Films with higher hard-segment ratios had the highest breaking strength but the water vapor permeability, on the other hand, became lower. Films cast from the solvent evaporation method had higher breaking strength and higher breaking elongation but lower water vapor permeability than films cast from the wet coagulation method. © 1994 John Wiley & Sons, Inc.     

豌豆淀粉/聚乳酸双层膜的制备与性能表征

采用溶液流延法以豌豆淀粉（PS）和聚乳酸（PLA）为原料制备了豌豆淀粉/聚乳酸（PS/PLA）双层薄膜。通过对双层薄膜的吸水性、溶解性、水蒸气透过性、拉伸性能、表面形貌等进行测试,研究了薄膜的力学性能、疏水性能以及水蒸气阻隔性能。结果表明：随着双层膜中聚乳酸层的比例增加,双层薄膜的吸水性、溶解性和水蒸气透过性逐渐降低,拉伸强度和拉伸模量逐渐增加,断裂伸长率逐渐下降,表明水蒸气阻隔效果明显,增加了膜的韧性,降低了膜的强度。当PLA和PS的质量比为50：50时,PS/PLA双层膜的拉伸强度为（13.47±0.75）MPa,拉伸模量为（0.848±0.002）GPa;断裂伸长率为（16.11±0.16）%,水蒸气透过系数为0.27×10^-10 g·cm/（cm²·s·Pa）。     

Photografting of N‐isopropylacrylamide and glycidyl methacrylate binary monomers on polyethylene film: Effect of mixed solvent consisting of water and organic solvent

Photografting (λ > 300 nm) of N‐isopropylacrylamide (NIPAAm) and glycidyl methacrylate (GMA) binary monomers (NIPAAm/GMA) on low‐density polyethylene film (thickness = 30 μm) was investigated at 60°C using mixed solvent consisting of water and an organic solvent such as acetone. Xanthone was used as a photoinitiator by coating it on the film surfaces. A maximum percentage of grafting was observed at a certain concentration of acetone in the mixed solvent, which was commonly observed for both ratios of NIPAAm/GMA, 8/2 and 7/3. Based on the photografting of NIPAAm/GMA on xanthone‐coated film, monomer reactivity ratios of NIPAAm (r₁) and GMA (r₂) were calculated using the Fineman–Ross method. The values were 0.31 ± 0.1 and 4.8 ± 0.2 for the water solvent system, while they were 0.96 ± 0.1 and 4.9 ± 0.1 for the mixed solvent system. NIPAAm/GMA‐grafted films with a homogeneous distribution of grafted chains were formed by photografting using water and mixed solvents. The NIPAAm/GMA‐grafted films exhibited temperature‐responsive characters, whereas the grafted films showed a reversible change in the degree of swelling between 0 and 50°C, respectively. Epoxy groups in the grafted poly(NIPAAm/GMA) chains could be aminated with ethylenediamine in N,N′‐dimethylformamide at 70°C for 3 h. Complexes of the aminated NIPAAm/GMA‐grafted chains with cupric ion exhibited catalytic activity for the decomposition of hydrogen peroxide at 20 to 50°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2469–2475, 2005     

Physical and electrochemical characterizations of poly(vinylidene fluoride‐co‐hexafluoropropylene)/SiO2‐based polymer electrolytes prepared by the phase‐inversion technique

Highly porous poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF–HFP)‐based polymer membranes filled with fumed silica (SiO₂) were prepared by a phase‐inversion technique, and films were also cast by a conventional casting method for comparison. N‐Methyl‐2‐pyrrolidone as a solvent was used to dissolve the polymer and to make the slurry with SiO₂. Phase inversion occurred just after the impregnation of the applied slurry on a glass plate into flowing water as a nonsolvent, and then a highly porous structure developed by mutual diffusion between the solvent and nonsolvent components. The PVdF–HFP/SiO₂ cast films and phase‐inversion membranes were then characterized by an examination of the morphology, thermal and crystalline properties, absorption ability of an electrolyte solution, ionic conductivity, electrochemical stability, and interfacial resistance with a lithium electrode. LiPF₆ (1M) dissolved in a liquid mixture of ethylene carbonate and dimethyl carbonate (1:1 w/w) was used as the electrolyte solution. Through these characterizations, the phase‐inversion polymer electrolytes were proved to be superior to the cast‐film electrolytes for application to rechargeable lithium batteries. In particular, phase‐inversion PVdF–HFP/SiO₂ (30–40 wt %) electrolytes could be recommended to have optimum properties for the application. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 140–148, 2006     

Water vapor permeability of poly(lactide)s: Effects of molecular characteristics and crystallinity

Amorphous‐made poly(L ‐lactide) [i.e., poly(L ‐lactic acid) (PLLA)], poly(L ‐lactide‐co‐D ‐lactide)[P(LLA‐DLA)](77/23), and P(LLA‐DLA)(50/50) films and PLLA films with different crystallinity (X_c) values were prepared, and the effects of molecular weight, D ‐lactide unit content (tacticity and optical purity), and crystallinity of poly(lactide) [i.e., poly(lactic acid) (PLA)] on the water vapor permeability was investigated. The changes in number‐average molecular weight (M_n) of PLLA films in the range of 9 × 10⁴–5 × 10⁵ g mol^?1 and D ‐lactide unit content of PLA films in the range of 0–50% have insignificant effects on their water vapor transmission rate (WVTR). In contrast, the WVTR of PLLA films decreased monotonically with increasing X_c from 0 to 20%, while leveled off for X_c exceeding 30%. This is probably due to the higher resistance of “restricted” amorphous regions to water vapor permeation compared with that of the “free” amorphous regions. The free and restricted amorphous regions are major amorphous components of PLLA films for X_c ranges of 0–20% and exceeding 30%, respectively, resulting in the aforementioned dependence of WVTR on X_c. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Rapid formation of flexible silk fibroin gel‐like films

Flexible silk fibroin gel‐like films with microporous morphology were prepared from B. mori silk fibroin fibers directly solubilized in formic acid/CaCl₂ solvent. These films were characterized by several analysis techniques to determine the structure and properties of films. The pore size of gel‐like films can be adjusted through SF concentration and Ca ions concentration. The controllable pore size in gel‐like films was grew from 3–5 μm to 100 μm under the increase of fibroin concentration from 1.0 wt % to 8.0 wt %. At the same time, the water content of silk fibroin gel‐like film decreased from 83.5 ± 3.4% to 68.2 ± 2.6%. With increasing Ca ions contents from 2.0 wt % to 10.0 wt % in dissolution process, the pore size and water content of silk fibroin gel‐like films grew larger, especially its water content values reached 86.2 ± 4.0% at 10.0 wt % Ca ions concentration. At wet condition, the gel‐like film with β‐sheet structure showed higher breaking stress (4.26 ± 0.31 MPa) and elongation (45.45 ± 15.79%) at 8.0 wt % concentration. With the preparation method, the membrane is hydrophilic and the pore size is adjustable, which contributes to high toughness and favorable cell growth environment, suggesting that these silk fibroin gel‐like films can be a potential candidate scaffold for biomedical applications, such as wound dressing, facial mask, contact lenses, etc. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41842.     

Porous biodegradable polyesters. I. Preparation of porous poly(L‐lactide) films by extraction of poly(ethylene oxide) from their blends

Porous poly(L ‐lactide) (PLLA) films were prepared by water extraction of poly(ethylene oxide) (PEO) from solution‐cast PLLA and PEO blend films. The dependence of blend ratio and molecular weight of PEO on the porosity and pore size of films was investigated by gravimetry and scanning electron microscopy. The film porosity and extracted weight ratio were in good agreement with the expected for porous films prepared using PEO of low molecular weight (M_w = 1 × 10³), but shifted to lower values than expected when high molecular weight PEO (M_w = 1 × 10⁵) was utilized. The maximum pore size was larger for porous films prepared from PEO having higher molecular weight, when compared at the same blending ratio of PLLA and PEO before water extraction. Differential scanning calorimetry of as‐cast PLLA and PEO blend films revealed that PLLA and PEO were phase‐separated at least after solvent evaporation. On the other hand, comparison of blend films before and after extraction suggested that a small amount of PEO was trapped in the amorphous region between PLLA crystallites even after water extraction and hindered PLLA crystallization during solvent evaporation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 629–637, 2000     

Melt processing of poly(L‐lactic acid) in the presence of organomodified anionic or cationic clays

Poly(L ‐lactic acid) (PLA) films are in use for various types of food packaging; however, a wider range of applications would be possible if the barrier properties of these films could be improved. To make such improvements, combinations of PLA with two nanofillers, laurate‐intercalated Mg‐Al layered double hydroxide (LDH‐C₁₂) and a cationic organomodified montmorillonite (MMT) clay (Cloisite® 30B), were investigated. The dispersion of these fillers in PLA by melt processing was explored using two methods, either by mixing the nanofillers with PLA granulate immediately before extrusion or by preparation and subsequent dilution of PLA‐nanofiller masterbatches. After melt processing of these materials, PLA molecular weight, thermal stability, film transparency, morphology, and permeability characteristics were determined. Direct addition of LDH‐C₁₂ drastically reduced the PLA molecular weight. Although this reduction in molecular weight was still very significant, it was less when a PLA/LDH‐C₁₂ masterbatch was processed. In contrast, there was no significant reduction in PLA molecular weight when processing with Cloisite® 30B. However, film transparency was compromised when either LDH or MMT nanofillers were used. Evidence from DSC analyses showed a significant increase in heat of fusion when LDH‐C₁₂ was dispersed in PLA compared with Cloisite® 30B, likely indicating a difference in nucleating properties. Complementary optical purity analyses suggested that racemization as a result of processing could influence the PLA crystallinity as determined by DSC in certain cases. A reduction in thermal stability when incorporating LDH‐C₁₂ could be a direct result of PLA molecular weight reduction. XRD and TEM analyses showed that both Cloisite® 30B‐ and LDH‐C₁₂‐based PLA composites yielded exfoliated and intercalated morphologies, but nanofiller agglomeration was also seen when LDH‐C₁₂ was used. PLA/Cloisite® 30B nanocomposite films exhibited significant enhancement in oxygen and water vapor barrier properties, but no such improvement was found in PLA/LDH‐C₁₂ nanocomposite films. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Reversible selectivity of water/organic solvent mixtures in poly(lactic acid) film

The separation properties of water/organic solvent mixtures in poly(lactic acid) (PLA) films were investigated. The organic solvent flux increased linearly as the feed concentration increased, whereas the water flux was almost constant up to a feed concentration of 30 wt %. Interestingly, the permselectivity of PLA films was reversed from organic solvent selectivity to high water selectivity depending on the type of organic solvent. The permselectivity was strongly correlated with the solution concentration at which the solvent‐induced crystallization of the PLA films occurred. The selectivity of permeation, solution, and diffusion in water/organic solvent mixtures was determined by the expanded free volume of the PLA films as a result of the interaction between PLA and the water/organic solvent mixture. The permeability behavior of water/organic solvent mixtures in PLA films was very complex. However, it was found that this behavior could be predicted through immersion tests. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43822.     

Antioxidant,antifungal, water binding,and mechanical properties of poly(vinyl alcohol) film incorporated with essential oil as a potential wound dressing material

In this study, the properties of poly (vinyl alcohol) (PVA) films incorporated with Zataria multiflora essential oil (ZMO) as a potential antioxidant/antibacterial material was investigated. PVA films were prepared from PVA solutions (2% w/v) containing different concentrations of ZMO. Water solubility, moisture absorption, water swelling, and water vapor permeability for pure PVA films were 57 ± 1.1, 99 ± 3.2%, 337 ± 8%, and 0.453 ± 0.015 g mm/m² h, respectively. Incorporation of ZMO into PVA films caused a significant decrease in water swelling and moisture absorption and increase in solubility and water vapor permeability. Tensile strength, elastic modulus, and elongation at break for pure PVA films were 13.5 ± 0.61 MPa, 15.2 ± 0.8 MPa, and 216 ± 4%, respectively. Incorporation of ZMO into the PVA films caused a significant decrease in tensile strength and elastic modulus and increase in elongation at break of the films. Pure PVA film showed UV‐visible light absorbance ranging from 280 to 440 nm with maximum absorbance at 320 nm. Addition of ZMO caused a significant increase in light absorbance and opacity. PVA films exhibited no antioxidant and antifungal activities, whereas PVA/ZMO films exhibited excellent antioxidant and antifungal properties. Although the bioactivity PVA films were improved by the addition of ZMO, however, the mechanical properties and water binding capacity of the films were weaken slightly. Thus, ZMO emulsified in the ethanol not compatible with PVA matrix and more suitable emulsifier was needed in order to obtain strong film with higher mechanical properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40937.     

Micromorphology,mechanical, crystallization and permeability properties analysis of HA/PBAT/PLA (HA,hydroxyapatite; PBAT,poly(butylene adipate‐co‐butylene terephthalate); PLA,polylactide) degradability packaging films

In this study, the self‐made nano‐hydroxyapatite (HA) and poly(butylene adipate‐co‐butylene terephthalate) copolyesters (PBAT) were used as fillers, and composite films of HA/PLA (PLA, polylactide) and HA/PBAT/PLA systems were prepared. The micromorphology, mechanical properties, thermal properties, crystallinity, water vapor permeability and oxygen permeability of the composite films were studied. The results show that the self‐made HA has a porous rod‐like structure with a size of 30–50 nm. PBAT was dispersed uniformly in the HA/PLA matrix in the form of spherical particles and formed many pores and holes. The tensile strength, elongation at break and modulus of elasticity of HA/PLA composite films were increased by adding 10 wt% PBAT. The addition of HA and PBAT played a synergistic function in improving the crystallinity of the composite films. The water vapor and oxygen permeabilities of HA/PLA and HA/10%PBAT/PLA composite films can be regulated by adjusting the amount of HA. The results of this study indicate that composite films with higher water vapor and oxygen permeabilities exhibit great potential for applications in green packaging and fresh‐keeping packaging. © 2019 Society of Chemical Industry     

Three‐layer sheets based on gelatin and poly(lactic acid), part 1: Preparation and properties

Glycerol‐plasticized gelatin (Ge‐30Gly) and poly(lactic acid) (PLA) films were prepared by heat‐compression, molded, and then piled to produce a biodegradable three‐layer sheet with PLA as outer layers and Ge‐30Gly as the inner layer. Lamination with PLA increased the moisture resistance and reduced the total soluble matter with respect to a single gelatin layer, while keeping transparency. The tensile strength of the multilayer sheet (36.24±4.27 MPa) increased 16 folds when compared to that of Ge‐30Gly. Lamination also exerted beneficial effects on the barrier properties. The WVP of the multilayer sheet (1.2 ± 0.1 10^?14 kg·m·Pa^?1·s^?1·m^?2) decreased with reference to that of Ge‐30Gly, while oxygen permeability (17.1 ± 2.3 cm³(O₂)·mm·m^?2·day^?1) was reduced with respect to that of neat PLA, and the value obtained was comparable to that of Ge‐30Gly layer. The presence of plasticized gelatin in the multilayer increased the energy at crack initiation (1.4 ± 0.3 J·m^?1) with respect to that of PLA. The improvement attained in all these properties was ascribed to the good compatibility and adhesion of the individual layers featured through hydrogen interactions between the carbonyl group from PLA and the hydrogen from the peptide bonds in gelatin. Compatibility was corroborated by scanning electron microscopy observations at PLA/Ge‐30Gly interface and by the absence of additional peaks in the tan δ curve of dynamic‐mechanical analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical properties and water vapor permeability of thin film from corn hull arabinoxylan

Isolated corn hull arabinoxylan was dissolved in water and provided a clear solution. Plasticizer (glycerol, propylene glycol, or sorbitol) was added to the arabinoxylan solution at 0–20 wt % (film dry weight), which was cast into stable films. Film thickness ranged from 22 to 32 μm. Mechanical properties, moisture content, and water vapor permeability (WVP) were studied for the arabinoxylan‐based films as a function of plasticizer concentration. Measured data for the corn hull arabinoxylan–based films were 13–18 wt % moisture content, 10–61 MPa tensile strength, 365–1320 MPa modulus, 6–12% elongation, and 0.23–0.43 × 10^?10 g m^?1 Pa^?1 s^?1 water vapor permeability. Plasticized arabinoxylan films produced in this study had lower WVPs than those of unplasticized films, which is likely attributable to the phenomenon known as antiplasticization. Scanning electron micrographs showed a homogeneous structure on film surfaces. Films containing sorbitol had the best moisture barrier properties. When grapes were coated with arabinoxylan and arabinoxylan/sorbitol films, weight loss rates of the fruit decreased by 18 and 41%, respectively, after 7 days. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2896–2902, 2004     

The effect of solvent mixture on the properties of solvent cast polylactic acid (PLA) film

The objective of this study was to investigate the effects of various solvents on the crystallinity and thermal expansion stability of PLA film. Three different PLA films were produced by the solvent casting technique; PLA in chloroform (PLA‐C), PLA in methylene chloride (PLA‐M), and PLA in methylene chloride: acetonitrile = 50: 50 (PLA‐MA). The PLA‐MA had higher % crystallinity, 46.15, than the PLA‐C, 24.03, and the PLA‐M, 14.25. With this increase in crystallinity, the PLA‐MA had improved thermal expansion stability as shown by very low accumulated dimensional changes at 20 to 100°C. Wide‐angle X‐ray diffraction identified multiple crystalline structures for the PLA‐MA. Film barrier properties were also measured. PLA‐MA had the lowest oxygen permeability. However, there was no significant difference in water vapor permeability among the three PLA films. The mechanical property tests revealed that the PLA‐C and PLA‐M were ductile while the PLA‐MA was brittle in behavior. The PLA‐MA was very hazy as compared with the PLA‐C and PLA‐M. This work has shown that the PLA‐MA had increased % crystallinity and, more importantly, it had improved thermal expansion stability which can be very beneficial for the flexible packaging industry. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Physicomechanical,optical, barrier,and wide angle X‐ray scattering studies of filled low density polyethylene films

Series of low density polyethylene (LDPE) films filled with different fillers such as silica, mica, soya protein isolate, potassium permanganate, and alumina were processed using a single screw extruder. The filled LDPE films were characterized for physicomechanical properties like tensile strength, percentage elongation at break, and tear strength, optical properties like percent transmission and haze. The barrier properties such as water vapor transmission rate and oxygen transmission rate of the filled LDPE films have also been reported. Microcrystalline parameters such as crystal size (〈N〉) and lattice distortion (g) of the filled LDPE films obtained using wide angle X‐Ray scattering method have been reported. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2781–2789, 2006     

Mechanical and water binding properties of carboxymethyl cellulose/multiwalled carbon nanotube nanocomposites

Carboxymethyl cellulose (CMC) composite films were prepared from CMC solutions (2% w/v) containing multiwalled carbon nanotubes (MWCNT) as nanofiller and glycerol (25% w/w CMC) as plasticizer. Tensile strength, elongation at break (EAB), young's modulus, water solubility, water swelling, water uptake, and water vapor permeability (WVP) for CMC films were 27.5 ± 2.5 MPa, 11.2 ± 0.8%, 198 ± 18 MPa, 57 ± 1.5%, 738 ± 25%, 124 ± 4%, and 0.55 ± 0.036 g.mm/m².kPa.h, respectively. By increasing the relative humidity from 11.4 to 85.5%, the moisture absorption (MA) of CMC films was increased from 4 to 38%. Incorporation of MWCNT into the matrix caused a significant increase in the tensile strength, decrease in EAB, increase in young's modulus, decrease in water solubility, decrease in water swelling, decrease in water uptake, and decrease in MA. CMC/MWCNT films containing 1% MWCNT showed the lowest WVP. Scanning electron microscopy showed a good dispersion of MWCNT in the CMC matrix. CMC/MWCNT films containing >1% MWCNT showed significant antibacterial activities against both Gram‐positive and Gram‐negative bacteria in a dose‐dependent manner. Thus, good mechanical properties and water resistance along with strong antibacterial activities make CMC films grafted with MWCNT as a suitable packaging material. POLYM. COMPOS., 36:145–152, 2015. © 2014 Society of Plastics Engineers     

Polystyrene‐block‐polylactide obtained by the combination of atom transfer radical polymerization and ring‐opening polymerization with a commercial dual initiator

A polystyrene (PS)‐b‐polylactide (PLA) block copolymer was prepared from the combination of atom transfer radical polymerization and ring‐opening polymerization with commercially available 2,2,2‐tribromoethanol as a dual initiator in a sequential two‐step procedure. Hydroxyl‐terminated polystyrene (PS‐OH)s with various molecular weights were first prepared with polydispersity indices lower than 1.3; these provided valuable macroinitiators for the polymerization of D,L ‐lactide. A block copolymer with a composition allowing the formation of hexagonally packed PLA cylinders in a PS matrix was then obtained. The PS‐b‐PLA thin films revealed, after vapor solvent annealing, a hexagonally packed organization of the PLA cylinders, which was oriented perpendicularly to the surface of the film. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphological and thermal properties of photodegradable biocomposite films

Biocomposites containing ultraviolet (UV) radiation absorbing inorganic nanofillers are of great interest in food packaging applications. The biodegradable polylactide (PLA) composite films were prepared by solvent casting method by incorporating 1 wt % of titanium dioxide (TiO₂) and Ag‐TiO₂ (silver nanoparticles decorated TiO₂) nanoparticles to impart the photodegradable properties. The films were exposed to UV radiation for different time periods and morphology of the composite films before and after UV exposure were investigated. The results showed that homogenous filler distribution was achieved in the case of Ag‐TiO₂ nanoparticles. The thermal properties and thermomechanical stability of the composite film containing Ag‐TiO₂ nanoparticles were found to be much higher than those of neat PLA and PLA/TiO₂ composite films. The scanning electron microscopy and X‐ray diffraction studies revealed that the photodegradability of PLA matrix was significantly improved in the presence of Ag‐TiO₂ nanoparticles. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Single Solvent‐Based Film Casting Method for the Production of Porous Polymer Films

A single solvent‐based film casting process for fabricating porous polymer films is developed in this study. The porous film is produced by mixing concentrated polylactic acid (PLA)/chloroform solution (20 wt%) and fresh chloroform solvent is followed by film casting. The average pore sizes of the films produced are seen to increase from 2.1 (±0.1) µm to 6.4 (±0.2) µm with increasing ratio of concentrated PLA solution and fresh solvent from 1:2 to 1:4. Functional groups of PLA after casting into porous film are confirmed via Fourier transform infrared spectroscopy analysis. Cytocompatibility studies (via Alamar Blue assessment) utilizing MG‐63 cells on the porous PLA films reveal an increase in cell metabolic activity up to 8 d postseeding. In addition, these direct cell culture studies show that the porous membranes support cell adhesion and growth not only on the surface but also through the porous structures of the membrane, highlighting the suitability of these porous films in tissue engineering applications.     

Influence of hydroxyl‐terminated polybutadiene additives on the poly(ether sulfone) ultra‐filtration membranes

Hydroxyl‐terminated polybutadiene (HTPB) was blended into a poly(ether sulfone) (PES) casting solution used to prepare ultra‐filtration (UF) membranes via the phase inversion technique. The membranes were then characterized by contact angle (CA) measurements and UF experiments. The CA was increased with the addition of HTPB in the PES membrane and also by lowering the gelation bath temperature. It was observed that the CA was lower for membranes prepared with N‐methyl‐2‐pyrrolidinone (NMP) as the solvent than those using N,N‐dimethylacetamide (DMAc) as solvent. The flux values were higher for membranes made using a 4°C gelation bath when compared with the ambient temperature ((25 ± 1)°C) irrespective of the cast solvents, NMP or DMAc. The flux values were much higher and the solute separations were lower for the HTPB‐based PES membranes than for the pure PES membrane, when the membranes were cast with DMAc as a solvent. On the other hand, both flux and separation values were much lower for the HTPB‐based PES membranes than for the pure PES membrane, when the membranes were cast using NMP. Atomic force microscopy and scanning electron microscopy were used for morphological characterization and the correlation of topography/photography with the performance data was also examined. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2292–2303, 2006