Durability of wood flour‐plastic composites exposed to accelerated freeze–thaw cycling. Part I. Rigid PVC matrix

This study examined the effects of accelerated freeze–thaw actions on the durability of wood fiber‐plastic composites. Rigid PVC formulations filled with various concentrations of wood flour (both pine and maple) were processed in a counterrotating twin‐screw extruder and exposed to cyclic freeze–thaw actions according to ASTM Standard D6662. Freeze–thaw cycling was also modified by omitting portions of the test (either the water or freezing) to verify whether or not moisture was the primary cause for property loss. The durability of exposed samples was assessed in terms of flexural properties, density, and dimensional stability. Scanning electron micrographs of unexposed and freeze–thaw‐exposed samples were taken to qualitatively evaluate the interfacial adhesion between the wood flour and PVC matrix. The experimental results indicated that the density was not affected by freeze–thaw cycling. The dimensional stability was also relatively unaffected, although greater wood flour content exhibited greater dimensional change. The loss in stiffness of the composites was statistically significant after only two freeze–thaw cycles, regardless of both the wood species and content. Conversely, the strength of the composites was not significantly affected by five freeze–thaw cycles at lower wood flour contents (50 and 75 phr). The deleterious effects of the freeze–thaw actions on the strength of the composites became apparent at higher wood flour content (100 phr) after only two freeze–thaw cycles for maple flour and five freeze–thaw cycles for pine flour. The property loss was attributed primarily to the water portion of the cycling, which appears to have led to the decreased interfacial adhesion between the wood flour and the rigid PVC matrix. J. VINYL. ADDIT. TECHNOL. 11:1–8, 2005. © 2005 Society of Plastics Engineers.     

Ultraviolet weathering of photostabilized wood‐flour‐filled high‐density polyethylene composites

Wood‐plastic composites are being increasingly examined for nonstructural or semistructural building applications. As outdoor applications become more widespread, durability becomes an issue. Ultraviolet exposure can lead to photodegradation, which results in a change in appearance and/or mechanical properties. Photodegradation can be slowed through the addition of photostabilizers. In this study, we examined the performance of wood flour/high‐density polyethylene composites after accelerated weathering. Two 2⁴ factorial experimental designs were used to determine the effects of two hindered amine light stabilizers, an ultraviolet absorber, a colorant, and their interactions on the photostabilization of high‐density polyethyl‐ ene blends and wood flour/high‐density polyethylene composites. Color change and flexural properties were determined after 250, 500, 1000, and 2000 h of accelerated weathering. The results indicate that both the colorant and ultraviolet absorber were more effective photostabilizers for wood flour/high‐density polyethylene composites than the hindered amine light stabilizers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2609–2617, 2003     

Effects of the accelerated freeze‐thaw cycling on physical and mechanical properties of wood flour‐recycled thermoplastic composites

This study investigated durability performance of wood‐plastic composites (WPCs) that were exposed to accelerated cycling of water immersion followed by freeze thaw (FT). The WPCs used in this study were made of high‐density polyethylene (HDPE) or polypropylene (PP) with radiata pine (Pinus radiata) wood flour using hot‐press molding. These two types of plastics included both recycled and virgin forms in the formulation. In the experiments, surface color, flexural properties, and dimensional stability properties (water absorption and thickness swelling) were measured for the FT cycled composites and the control samples. Interface microstructures and thermal properties of the composites were also investigated. The results show that the water absorption and the thickness swelling of the composites increased with the FT weathering. In the meantime, the flexural strength and stiffness decreased. Scanning electron microscopy (SEM) images of the fractured surfaces confirmed a loss of interface bonding between the wood flour and the polymer matrix. Differential scanning calorimetry (DSC) showed a decrease in crystallization enthalpy and crystallinity of the wood flour‐plastic composites as compared with the neat PP and HDPE samples. The crystallinity of the FT cycled composites using the virgin plastics (vPP and vHDPE) increased; however, the composites with the recycled plastics decreased in comparison with corresponding control samples. In general, the properties of the composites were degraded significantly after the accelerated FT cycling. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effects of copper amine treatment on mechanical properties of PVC/wood‐flour composites

Copper amine–treated wood flour was added to PVC [poly(vinyl chloride)] matrix in order to manufacture PVC/wood‐flour composites. Effects of copper treatments on the mechanical properties of PVC‐wood composites were evaluated. Unnotched impact strength, flexural strength, and flexural toughness of the composites were significantly improved by the wood‐flour copper treatment. The optimum copper concentration range was 0.2 to 0.6 wt% of wood flour. Fractured surfaces were examined by using scanning electron microscopy (SEM) combined with energy‐dispersive spectroscopy (EDS). PVC/wood interfacial debonding was the main fracture mode of untreated wood‐flour composites, whereas wood‐particle pullout and breakage dominating the fractured surfaces of copper‐treated wood‐flour composites. On the fractured surfaces, more PVC could be found on the exposed copper‐treated wood particles than on untreated wood, a result suggesting improved PVC‐wood interfacial adhesion after copper treatments. J. Vinyl Addit. Technol. 10:70–78, 2004. © 2004 Society of Plastics Engineers.     

Effect of weathering cycle and manufacturing method on performance of wood flour and high‐density polyethylene composites

Wood–plastic lumber is promoted as a low‐maintenance high‐durability product. When exposed to accelerated weathering, however, wood–plastic composites may experience a color change and loss in mechanical properties. Differences in weathering cycle and composite surface characteristics can affect the rate and amount of change caused by weathering. In this study, 50% wood flour filled high‐density polyethylene composite samples were injection molded, extruded, or extruded and then planed to remove the manufacturing surface characteristics. Composites were exposed to two accelerated weathering cycles in a xenon arc weathering apparatus. This apparatus exposed the samples to xenon arc radiation, which is a combination of UV, visible, and IR radiation that is similar to solar radiation. Composites were exposed to radiation with or without water spray. After exposure to radiation and water spray, composites with more wood component at the surface (i.e., planed samples) experienced a larger percentage of total loss in flexural modulus of elasticity and strength after weathering compared with the other composites. Composites exposed to radiation only did not experience as much change in properties as those exposed to radiation with water spray. The results of this study demonstrate that exposing wood–plastic composites to water spray in combination with radiation is more severe than exposing wood–plastic composites to radiation only. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3131–3140, 2006     

Novel coupling agents for PVC/wood‐flour composites *

Effective interfacial adhesion between wood fibers and plastics is crucial for both the processing and ultimate performance of wood–plastic composites. Coupling agents are added to wood–plastic composites to promote adhesion between the hydrophilic wood surface and hydrophobic polymer matrix, but to date no coupling agent has been reported for PVC/wood‐fiber composites that significantly improved their performance and was also cost‐effective. This article presents the results of a study using chitin and chitosan, two natural polymers, as novel coupling agents for PVC/wood‐flour composites. Addition of chitin and chitosan coupling agents to PVC/wood‐flour composites increased their flexural strength by ～20%, their flexural modulus by ～16%, and their storage modulus by ～33–74% compared to PVC/wood‐flour composite without the coupling agent. Significant improvement in composite performance was attained with 0.5 wt% of chitosan and when 6.67 wt% of chitin was used. J. VINYL ADDIT. TECHNOL., 11:160–165, 2005. © 2005 Society of Plastics Engineers     

Effect of processing method on surface and weathering characteristics of wood–flour/HDPE composites

Wood–plastic lumber is promoted as a low‐maintenance high‐durability product. When exposed to accelerated weathering, however, wood–plastic composites may experience a color change and/or loss in mechanical properties. Different methods of manufacturing wood–plastic composites lead to different surface characteristics, which can influence weathering. In this study, 50% wood–flour‐filled high‐density polyethylene (HDPE) composite samples were injection molded, extruded, or extruded and then planed, to remove the manufacturing surface characteristics. Fourier transform infrared spectroscopy was used to chemically show the difference in surface components. The samples were weathered in a xenon‐arc weathering apparatus for 1000, 2000, and 3000 h and analyzed for color fade and loss of flexural modulus of elasticity and strength. Final color (lightness) after weathering was not dependent on the manufacturing method. However, the manufacturing method was related to mechanical property loss caused by weathering. Composites with more wood component at the surface (i.e., planed samples) experienced a larger percentage of total loss in flexural modulus of elasticity and strength after weathering. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1021–1030, 2004     

Durability of Wood Flour-Thermoplastic Composites under Extreme Environmental Conditions and Fungal Exposure

Abstract

The main purpose of this research work was to investigate the response of wood flour reinforced polyethylene composites to 2 hours water boiling, five complete boiling and freezing cycles and fungal (Gloeophyllumm Traebum/Brown-rot fungus) exposure. Five composite formulations were manufactured and analyzed (0, 50, 60, 70 and copper carbonate treated 60% wood flour/polyethylene composites). The results showed that wood flour loading decreased the resistance of the composites to moisture and fungal environment. The exposure of the composites to 2 hours water boiling and five complete boiling and freezing cycles caused serious damage to the interfacial adhesion between wood flour and polyethylene matrix due to contraction and swelling stresses developed during cyclic exposure. The addition of 1 percent copper carbonate salt during compounding of wood flour and polyethylene prevented the colonization and proliferation of fungus on the surface of the composites, but had a negative effect on the water uptake and flexural properties of the composites.     

Surface chemistry and mechanical property changes of wood‐flour/high‐density‐polyethylene composites after accelerated weathering

Although wood–plastic composites have become more accepted and used in recent years and are promoted as low‐maintenance, high‐durability building products, they do experience a color change and a loss in mechanical properties with accelerated weathering. In this study, we attempted to characterize the modulus‐of‐elasticity (MOE) loss of photostabilized high‐density polyethylene (HDPE) and composites of wood flour and high‐density polyethylene (WF/HDPE) with accelerated weathering. We then examined how weathering changed the surface chemistry of the composites and looked at whether or not the surface changes were related to the MOE loss. By examining surface chemistry changes, we hoped to begin to understand what caused the weathering changes. The materials were left unstabilized or were stabilized with either an ultraviolet absorber or pigment. After 1000 and 2000 h of accelerated weathering, the samples were tested for MOE loss. Fourier transform infrared (FTIR) spectroscopy was employed to monitor carbonyl and vinyl group formation at the surface. Changes in the HDPE crystallinity were also determined with FTIR techniques. It was determined that structural changes in the samples (carbonyl group formation, terminal vinyl group formation, and crystallinity changes) could not be reliably used to predict changes in MOE with a simple linear relationship. This indicated that the effects of crosslinking, chain scission, and crystallinity changes due to ultraviolet exposure and interfacial degradation due to moisture exposure were interrelated factors for the weathering of HDPE and WF/HDPE composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2263–2273, 2004     

Effects of chemical modification of wood flour on the rheological properties of high‐density polyethylene blends

Chemical modification of lignocellulosic fibers can improve interfacial adhesion and dimensionally stabilize the resulting plastic composites. This study examined the rheological properties of wood flour/high density polyethylene (HDPE) melts after poplar wood flour was modified with glutaraldehyde (GA, mainly cell wall cross‐linking) and 1,3‐dimethylol‐4,5‐dihydroxyethyleneurea (DMDHEU, mainly poly‐condensation). Results show improvement in both the dispersibility of treated wood flour in the HDPE and its interfacial compatibility. Treatment with GA decreased melt viscosity, moduli, and shear stress as evidenced by rheometry. However, the modifying effects of DMDHEU were not observed, which was mainly due to reduced HDPE content. This study indicates that chemical modification of wood flour is a promising approach to improve the processability of highly filled wood thermoplastic composites via extrusion/injection molding processing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41200.     

木质填料种类及含量对木塑复合材料性能的影响

研究了木质填料的种类和含量对木塑复合材料性能的影响。实验发现:随着木粉、竹粉含量的提高,复合材料的拉伸强度、维卡软化温度、弯曲强度和弯曲模量都得到了较大幅度的提高,冲击强度、断裂伸长率和熔体流动速率有所下降。不同粒径和不同种类的木质填料对复合材料的力学性能也有明显的影响,以100目木粉制得复合材料的性能最好,DSC实验数据分析表明:木粉、竹粉含量的变化对复合材料体系的熔融温度有影响;SEM扫描冲击断口形貌表明:相容剂能够有效改善木粉与HDPE界面的相容性,提高界面黏合力,从而使复合材料的性能得到提高。     

Effect of compatibilizer on the natural durability of wood flour/high density polyethylene composites against rainbow fungus (Coriolus versicolor)

To evaluate the effect of compatibilizer on the natural durability of wood flour/high density polyethylene composites against Coriolus versicolor, composites containing 25% and 50% by weight maple wood flour and 1% and 2% compatibilizer (Maleic anhydride polyethylene (MAPE)), respectively, were sampled. Identical specimens of the same composites without the compatibilizer were also prepared. Physical and mechanical properties of all specimens, including water absorption, flexural modulus, flexural strength, impact strength and hardness, were determined prior to and after incubation with the fungus for 14 weeks at 25°C and 75% relative humidity. Weight losses of the specimens were also determined after incubation. Results indicated that the compatibilizer had significant effects on the natural durability of the studied composite formulations so that all mechanical properties were affected by the fungus to greater extents in the case of uncompatibilized specimens than the compatibilized ones. Weight loss of the uncompatibilized composites was also higher than that of compatibilized ones. Higher water absorption was observed in all cases after incubation. However, the increase in water absorption was considerably higher in the case of uncompatibilized specimens. POLYM. COMPOS., 28:273–277, 2007. © 2007 Society of Plastics Engineers     

甲基化木粉与PE-g-MAH对木粉/HDPE复合材料力学性能的协同作用研究

主要研究了木粉表面甲基化改性和增容剂马来酸酐接枝聚乙烯(PE-g-MAH)对木粉/高密度聚乙烯(HDPE)复合材料力学性能的协同作用。木粉经表面甲基化处理后,与10%PE-g-MAH协同使用,甲基化木粉/PE-g-MAH/HDPE复合材料的拉伸强度、弯曲强度和冲击强度均明显高于未改性木粉/PE-g-MAH/HDPE复合材料,其原因在于在PE-g-MAH的作用下,甲基化木粉在聚合物基体中分布更加均匀,两者的界面作用力更高,即甲基化木粉和PE-g-MAH对提升木粉/HDPE复合材料的力学性能具有良好的协同作用。     

Wood‐thermoplastic composites from wood flour and high‐density polyethylene

High‐density polyethylene/wood flour (HDPE/WF) composites were prepared by a twin‐screw extruder. The effects of WF, silane coupling agents, polymer compatibilizers, and their content on the comprehensive properties of the WF/HDPE composites have been studied in detail, including the mechanical, thermal, and rheological properties and microstructure. The results showed that both silane coupling agents and polymer compatibilizers could improve the interfacial adhesion between WF and HDPE, and further improve the properties of WF/HDPE composites, especially with AX8900 as a compatibilizer giving higher impact strength, and with HDPE‐g‐MAH as a compatibilizer giving the best tensile and flexural properties. The resultant composite has higher strength (tensile strength = 51.03 MPa) and better heat deflection temperature (63.1°C). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Wood‐fiber/high‐density‐polyethylene composites: Coupling agent performance

The coupling efficiency of seven coupling agents in wood–polymer composites (WPC) was investigated in this study. The improvement on the interfacial bonding strength, flexural modulus, and other mechanical properties of the resultant wood fiber/high‐density polyethylene (HDPE) composites was mainly related to the coupling agent type, function groups, molecular weight, concentration, and chain structure. As a coupling agent, maleated polyethylene (MAPE) had a better performance in WPC than oxidized polyethylene (OPE) and pure polyethylene (PPE) because of its stronger interfacial bonding. A combination of the acid number, molecular weight, and concentration of coupling agents had a significant effect on the interfacial bonding in WPC. The coupling agents with a high molecular weight, moderate acid number, and low concentration level were preferred to improve interfacial adhesion in WPC. The backbone structure of coupling agents also affected the interfacial bonding strength. Compared with the untreated composites, modified composites improved the interfacial bonding strength by 140% on maximum and the flexural storage modulus by 29%. According to the statistical analysis, 226D and 100D were the best of the seven coupling agents. The coupling agent performance was illustrated with the brush, switch, and amorphous structures. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 93–102, 2005     

Wood/plastic composites co‐extruded with multi‐walled carbon nanotube‐filled rigid poly(vinyl chloride) cap layer

Wood/plastic composites (WPCs) can absorb moisture in a humid environment due to the hydrophilic nature of the wood in the composites, making products susceptible to microbial growth and loss of mechanical properties. Co‐extruding a poly(vinyl chloride) (PVC)‐rich cap layer on a WPC significantly reduces the moisture uptake rate, increases the flexural strength but, most importantly, decreases the flexural modulus compared to uncapped WPCs. A two‐level factorial design was used to develop regression models evaluating the statistical effects of material compositions and a processing condition on the flexural properties of co‐extruded rigid PVC/wood flour composites with the ultimate goal of producing co‐extruded composites with better flexural properties than uncapped WPCs. Material composition variables included wood flour content in the core layer and carbon nanotube (CNT) content in the cap layer of the co‐extruded composites, with the processing temperature profile for the core layer as the only processing condition variable. Fusion tests were carried out to understand the effects of the material compositions and processing condition on the flexural properties. Regression models indicated all main effects and two powerful interaction effects (processing temperature/wood flour content and wood flour content/CNT content interactions) as statistically significant. Factors leading to a fast fusion of the PVC/wood flour composites in the core layer, i.e. low wood flour content and high processing temperature, were effective material composition and processing condition parameters for improving the flexural properties of co‐extruded composites. Reinforcing the cap layer with CNTs also produced a significant improvement in the flexural properties of the co‐extruded composites, insensitive to the core layer composition and the processing temperature condition. Copyright © 2009 Society of Chemical Industry     

Chemical treatment of wood fiber and its reinforced unsaturated polyester composites

In order to enhance the interfacial adhesion between wood fiber and an unsaturated polyester matrix (UPE), acrylic acid (acrylic acid)/poly(methyl methacrylate), and (acrylic acid)/silanization (AAS) were used to treat the wood fibers. The mechanical properties and the impact fracture surfaces of the prepared composites were measured and characterized, and the fracture mechanism of these kinds of composites was analyzed. The results showed that the AAS composites possessed the optimum comprehensive mechanical properties. When the weight fraction of wood fiber was 16%, the flexural strength and flexural modulus of the AAS composites were increased by 28.9 and 51.8%, respectively, compared to those of untreated composites. The highest tensile strength and lowest water absorption were also noted for AAS composites. These composites possessed the strongest interfacial adhesion between wood fiber and the UPE matrix. J. VINYL ADDIT. TECHNOL., 19:18–24, 2013. © 2013 Society of Plastics Engineers     

Comparative mechanical,fire‐retarding,and morphological properties of high‐density polyethylene/(wood flour) composites with different flame retardants

Aluminum hydroxide, magnesium hydroxide, and 1,2‐bis(pentabromophenyl) ethane were incorporated into high‐density polyethylene (HDPE) and wood flour composites, and their mechanical properties, morphology, and fire‐retardancy performance were characterized. The addition of flame retardants slightly reduced the modulus of elasticity and modulus of rupture of composites. Morphology characterization showed reduced interfacial adhesion among wood flour, HDPE, and flame retardants in the composites compared with control composites (HDPE and wood flour composites without the addition of flame retardants). The flame retardancy of composites was improved with the addition of the flame retardants, magnesium hydroxide and 1,2‐bis(pentabromophenyl) ethane, especially 1,2‐bis(pentabromophenyl) ethane, with a significant decrease in the heat release rate and total heat release. Char residue composition and morphology, analyzed by attenuated total reflectance, Fourier‐transform infrared spectroscopy, and scanning electron microscopy, showed that the char layer was formed on the composite surface with the addition of flame retardants, which promoted the fire performance of composites. The composites with 10 wt% 1,2‐bis(pentabromophenyl) ethane had good fire performance with a continuous and compact char layer on the composite surface. J. VINYL ADDIT. TECHNOL., 24:3–12, 2018. © 2015 Society of Plastics Engineers     

Studies on the Thermal and Mechanical Properties of Foamed Wood-Polymer Composites

Wood flour-polypropylene foamed composites, in ratios of 10:90, 20:80, 30:70, and 40:60 (wt./wt.), were prepared with and without maleic anhydride treatment of wood flour and maleic anhydride-grafted PP (MAgPP). The effects of the amount of wood flour and its treatment on the morphology, the mechanical properties, and the thermal properties of the composites were investigated. Vicat softening temperatures (VST) were recorded as 112.9°C, 103.2°C, and 96.2°C for MAgPP wood flour (MPP), maleic anhydride-treated wood flour (MWF), and untreated wood flour (UWF) (40:60 wt./wt.) foamed composites, respectively. The heat distortion temperatures (HDT) were measured to be 80°C, 76°C, and 58°C for the respective composites. DSC thermograms showed an increase in the crystallinity of MPP and MWF composites with an increase in the ratio of wood flour in the composite, whereas the opposite trend was observed in untreated wood flour. Except for impact strength and flexural strength, Young's modulus, flexural modulus, and hardness all increased with an increase in wood flour content. The micrographs confirmed the foaming. The improvement in the properties of the composites is due to the increment in interfacial bonding between polymer and wood flour, which is caused by the compatibilizers.     

Bleached extruder chemi‐mechanical pulp fiber‐PLA composites: Comparison of mechanical,thermal, and rheological properties with those of wood flour‐PLA bio‐composites

An environmentally friendly bleached extruder chemi‐mechanical pulp fiber or wood flour was melt compounded with poly(lactic acid) (PLA) into a biocomposite and hot compression molded. The mechanical, thermal, and rheological properties were determined. The chemical composition, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that the hemicellulose in the pulp fiber raw material was almost completely removed after the pulp treatment. The mechanical tests indicated that the pulp fiber increased the tensile and flexural moduli and decreased the tensile, flexural, and impact strengths of the biocomposites. However, pulp fiber strongly reinforced the PLA matrix because the mechanical properties of pulp fiber‐PLA composites (especially the tensile and flexural strengths) were better than those of wood flour‐PLA composites. Differential scanning calorimetry analysis confirmed that both pulp fiber and wood flour accelerated the cold crystallization rate and increased the degree of crystallinity of PLA, and that this effect was greater with 40% pulp fiber. The addition of pulp fiber and wood flour modified the rheological behavior because the composite viscosity increased in the presence of fibers and decreased as the test frequency increased. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44241.