Effect of Vapor—Liquid—Solid and Vapor—solid Silicon Carbide Whiskers on the Effective Thermal Diffusivity/Conductivity of Silicon Nitride Matrix Composites

A study was conducted of the relative effect of vapor—liquid—solid (VLS) and vapor—solid (VS) SiC whiskers on the effective thermal diffusivity and conductivity of pressed-densified silicon nitride. It was found that VLS whiskers cause an increase in the thermal diffusivity/conductivity, whereas the opposite effect was found for the VS-SiC whiskers. Comparison with composite theory suggests that the VS-SiC whiskers have a thermal conductivity as low as 25 to 30 W/(m·K). In contrast the VLS-SiC whiskers appear to have a value for the thermal conductivity of at least about 100 W/(m·K) to as high as 250 W/(m·K). These large differences in thermal conductivity for these two types of SiC whiskers are attributed to the much larger density of structural defects in the VS-SiC whiskers, which act as phonon scatterers, thereby lowering the thermal conductivity.     

Electrical Properties of Boron Nitride Matrix Composites: I, Analysis of McLachlan Equation and Modeling of the Conductivity of Boron Nitride–Boron Carbide and Boron Nitride–Silicon Carbide Composites

The McLachlan equation, which incorporates both effective medium models and percolation, was used to predict the volume fraction–conductivity relationships of insulator–conductor composites, and results were compared with experimental data. Two composite systems were investigated (BN–B₄C and BN–SiC). Both systems are anisotropic, because of the orientation of BN platelets perpendicular to the hot-pressing direction. For BN–B₄C composites, with increasing B₄C content, the ac and dc conductivities are relatively constant to ∼40% B₄C (the critical volume fraction). At this composition, the conductivity suddenly increases to a value closer to that of B₄C and then resumes a gradual increase. Little difference is seen for measurements made perpendicular or parallel to the hot-pressing direction, i.e., perpendicular or parallel to the BN platelets. Similar results are found for the BN–SiC composites, except that the critical volume fraction is ∼20% SiC in this case. The experimental curves are in good agreement with those predicted by the McLachlan equation. The parameters s and t of the McLachlan equation relate to the morphology of the phases present in the microstructure. The critical volume fraction relates to the connectivity of the phases in the composites.     

Effect of Interfacial Reaction on the Thermal Conductivity of Al–SiC Composites with SiC Dispersions

The effect of interfacial reactions between Al and SiC on the thermal conductivity of SiC-particle-dispersed Al-matrix composites was investigated by X-ray diffraction and transmission electron microscopy (TEM), and the thermal barrier conductance ( h _c) of the interface in the Al–SiC composites was quantified using a rule of mixture regarding thermal conductivity. Al–SiC composites with a composition of Al (pure Al or Al–11 vol% Si alloy)–66.3 vol% SiC and a variety of SiC particle sizes were used as specimens. The addition of Si to an Al matrix increased the thermal barrier conductance although it decreased overall thermal conductivity. X-ray diffraction showed the formation of Al₄C₃ and Si as byproducts in addition to Al and SiC in some specimens. TEM observation indicated that whiskerlike products, possibly Al₄C₃, were formed at the interface between the SiC particles and the Al matrix. The thermal barrier conductance and the thermal conductivity of the Al–SiC composites decreased with increasing Al₄C₃ content. The role of Si addition to an Al matrix was concluded to be restraining an excessive progress of the interfacial reaction between Al and SiC.     

Mechanical Properties and Microstructure of Whisker-Reinforced Alumina–30 vol% Glass Matrix Composite

High-density whisker-reinforced composites of an alumina-30 vol% glass matrix material were produced by hot-pressing in the temperature range 1350° to 1400°C in air. Significant improvement was observed in the strength of composites containing 15 vol% SiC whiskers, up to ∼550 MPa, but with only a small effect on the fracture toughness. In composites containing Si₃N₄ whiskers, no reinforcement was achieved. Transmission electron microscopy showed the formation of a protective layer of amorphous silica on the SiC whiskers, while the Si₃N₄ whiskers were found to react with the matrix. The mechanical properties were related to the microstructure and the density of the samples.     

Tetragonal Zirconia Polycrystals Reinforced with SiC Whiskers

The microstructure and the mechanical properties of hot-pressed tetragonal ZrO₂ polycrystals (TZP) reinforced with up to 30 vol% SiC whiskers were studied. The SiC whisker-TZP composites were stable under the hot-pressing conditions at 1450°C. Annealing in an oxidizing atmosphere at ∼1000°C resulted in glass formation and microcracking caused by whisker oxidation and transformation of the ZrO₂ grains near the whiskers to monoclinic symmetry. The fracture toughness was markedly improved by the dispersed whiskers (∼12 Mpa·m^1/2 at 30 vol% SiC) compared to the values measured for the matrix (∼6 Mpa·m^1/2). The flexural strength of the hot-pressed TZP-30 vol% SiC whisker composite at 1000°C (∼400 MPa) was twice that of the TZP matrix.     

High Thermal Conductivity in Silicon Nitride with Anisotropie Microstructure

Silicon nitride was fabricated by tape casting of α-Si₃N₄ powder with 5 wt% Y₂O₃ and 5 vol% rodlike β-Si₃N₄ seed particles, followed by tape stacking, hot pressing under 40 MPa, and annealing at 1850°C for 2-66 h under a nitrogen pressure of 0.9 MPa. Silicon nitrides fabricated by this procedure exhibited a highly anisotropic microstructure with large elongated grains (developed from seed particles) uniaxially oriented parallel to the casting direction. Thermal conductivities parallel to the grain alignment were much higher than those measured in other directions and exhibited high values of up to 120 W/(m.K). The anisotropic thermal conductivity of the specimen could be explained by the rule of mixture, considering that large elongated grains developed from seeds have higher thermal conductivity than a small-grained matrix.     

Toughening of Silicon Nitride Matrix Composites by the Addition of Both Silicon Carbide Whiskers and Silicon Carbide Particles

Si₃N₄ matrix composites reinforced by SiC whiskers, SiC particles, or both were fabricated using the hot-pressing technique. The mechanical properties of the composites containing various amounts of these SiC reinforcing materials and different sizes of SiC particles were investigated. Fracture toughness of the composites was significantly improved by introducing SiC whiskers and particles together, compared with that obtained by adding SiC whiskers or SiC particles alone. On increasing the size of the added SiC particles, the fracture toughness of the composites reinforced by both whiskers and particles was increased. Their fracture toughness also showed a strong dependence on the amount of SiC particles (average size 40 μm) and was a maximum at the particle content of 10 vol%. The maximum fracture toughness of these composites was 10.5 MPa·m^1/2 and the flexural strength was 550 MPa after addition of 20 vol% of SiC whiskers and 10 vol% of SiC particles having an average particle size of 40 μm. These mechanical properties were almost constant from room temperature to temperatures around 1000°C. Fracture surface observations revealed that the reinforcing mechanisms acting in these composites were crack deflection and crack branching by SiC particles and pullout of SiC whiskers.     

Microstructural Studies in Alkoxide-Derived Mullite/Zirconia/Silicon Carbide-Whisker Composites

Mullite composites toughened with ZrO₂ (with or without a MgO or Y₂O₃ stabilizer) and/or SiC whiskers (SiC( w )) were fabricated by hot-pressing powders prepared from Al, Si, Zr, and Mg(Y) alkoxide precursors by a sol–gel process. Micro-structures were studied by using XRD. SEM, and analytical STEM. Pure mullite samples contained prismatic, preferentially oriented mullite grains. However, the addition of ZrO₂, as well as the hot-pressing temperature, affected the morphology and grain size in the composites; a fine, uniform, equiaxed microstructure was obtained. The effect of SiC( W ) was less pronounced than that of ZrO₂. Glassy phases were present in mullite and mullite/SiC( W ) composites, but were rarely observed in Al₂O₃-rich or ZrO₂-containing samples. The formation of zircon due to the reaction between ZrO₂ and SiO₂ and the considerable solid solution of SiO₂ in ZrO₂ prevented the formation of the glassy phase, whereas the reaction between Al₂O₃ and MgO in MgO-containing samples formed a spinel phase and also deprived the ZrO₂ phase of the stabilizer. Intergranular ZrO₂ particles were either monoclinic or tetragonal, depending on size and stabilizer content; small intragranular ZrO₂ inclusions were usually tetragonal in structure.     

Processing and Characterization of SiC-Whisker-Reinforced Alumina-Matrix Composites

Brittle monolithic alumina can be reinforced with highstrength single-crystal SiC whiskers with the effect of increasing fracture toughness. In this study, well-mixed and nearly fully dense SiC whisker/alumina composites were fabricated by wet-blending the constituents and uniaxially hot-pressing the resulting powder. The alumina-matrix grain size depended on whisker volume fraction, whisker surface-oxygen content, and hot-pressing environment. Fracture toughness, measured by an indentation-fracture method, increased from 3.0 MPa·m^1/2 for the hot-pressed unreinforced alumina to 10.7 MPa·m^1/2 for the composite containing 25 vol% SiC whiskers. Fracture surfaces revealed evidence of toughening by the mechanisms of crack deflection, pullout, and crack bridging by the whiskers. The observed increase in fracture toughness of alumina due to the addition of SiC whiskers was correlated with existing models of toughening mechanisms.     

Effect of heat transfer channels on thermal conductivity of silicon carbide composites reinforced with pitch-based carbon fibers

In this study, silicon carbide (SiC) composites reinforced with pitch-based carbon fibers and composed of heat transfer channels were fabricated by combining chemical vapor infiltration and reactive melting infiltration method. It was observed that the internal heat conduction skeleton of pitch-based carbon fibers was sequentially formed. The thermal conductivities from room temperature to 500 °C along through-thickness direction and in-plane direction were investigated. The results showed that C_pf/SiC composites with heat transfer channels possessed excellent thermal conductvity in two directions, and the thermal conductivity increased with increasing volume content of heat transfer channels. The thermal conductivity in through-thickness direction reached 38.89 W/(m·K), and that for in-plane direction reached 112.42 W/(m·K). Theoretical calculations were empolyed to study the temperature dependence of the C_pf/SiC composites. The variations in slope A′ and intercept B′ values of fitted curves were in good agreement with the experimental results. To verify the reliablilty of the theoretical model, the C_pf/SiC composites were heated at 1650 °C for 2 h and the thermal conductivity exhibited further improvement due to the formation of more perfect crystalline structure. Thermal conductivity through thickness direction improved to 43.49 W/(m·K), and that in in-plane direction improved to 142.49 W/(m·K), which could be identified by the theoretical model. Finally, the leading edge model was established by using ABAQUS finite element analysis software to evaluate the potential application of the composites. Owing to the outstanding thermal conductivity, the leading edge obtained by using C_pf/SiC composites in this study exhibited lower temperature gradient and a more uniform temperature distribution. Moreover, less thermal stress and displacement were generated during heating process.     

Volume Fraction and Whisker Orientation Dependence of the Electrical Properties of SiC-Whisker-Reinforced Mullite Composites

The electrical behavior of hot-pressed mullite composites reinforced with 10, 20, and 30% SiC whiskers (SiC_w) was evaluated in the frequency range 100 Hz–10 MHz and compared with 2 GHz data as well as dc resistivity measurements. It is found that the addition of SiC_w has a dramatic effect on the dielectric properties as well as the resistivity of these materials. The ac properties (dielectric constant, dielectric loss, and impedance) show a strong dependence on the volume fraction of SiC and on the orientation of the electric field with respect to the hot-pressing direction and hence the whisker orientation. The dc resistivity measurements are sensitive to the whisker volume fraction but cannot easily discriminate between those samples that were measured parallel or perpendicular to the hot-pressing direction as was possible with the ac measurements.     

炭前驱体形态对C/C复合材料导热系数的影响

利用热塑性中间相沥青为黏结剂,短炭纤维.增强体,一步热压成型制备C/C导热复合材料.采用SEM和偏光显微镜观察等分析手段,研究了2∶1,2.5∶1和3∶1三种不同管径比对C/C复合材料的影响.结果表明:通过热压模具空腔结构的改变可以引起炭前驱体挤出形态的变化,使得轴向基体炭有序生长与短炭纤维增强体呈现有序排列,其中间相液晶分子垂直和平行于模压压力方向均排列成纤维状长程有序结构,短切纤维呈现出与压力平行方向排布.当空腔管径比为3:1,轴向导热系数由86.2 W/(m·K)增大至115.5 W/(m· K),各向异性比由1.6减小为1.2.由此所得块体C/C复合材料具有显著的二维取向结构,轴径向导热系数趋于平衡.     

Control of Composition and Structure in Laminated Silicon Nitride/Boron Nitride Composites

Based on a biomimetic design, Si₃N₄/BN composites with laminated structures have been prepared and investigated through composition control and structure design. To further improve the mechanical properties of the composites, Si₃N₄ matrix layers were reinforced by SiC whiskers and BN separating layers were modified by adding Si₃N₄ or Al₂O₃. The results showed that the addition of SiC whiskers in the Si₃N₄ matrix layers could greatly improve the apparent fracture toughness (reaching 28.1 MPa·m^1/2), at the same time keeping the higher bending strength (reaching 651.5 MPa) of the composites. Additions of 50 wt% Al₂O₃ or 10 wt% Si₃N₄ to BN interfacial layers had a beneficial effect on the strength and toughness of the laminated Si₃N₄/BN composites. Through observation of microstructure by SEM, multilevel toughening mechanisms contributing to high toughness of the laminated Si₃N₄/BN composites were present as the first-level toughening mechanisms from BN interfacial layers as crack deflection, bifurcation, and pull-out of matrix sheets, and the secondary toughening mechanism from whiskers in matrix layers.     

Improved thermal conductivity and mechanical properties of SiC/SiC composites using pitch-based carbon fibers

Pitch-based carbon fibers were assembled in horizontal and thickness directions of SiC/SiC composites to form three-dimensional heat conduction networks. The effects of heat conduction networks on microstructures, mechanics, and thermal conductivities were investigated. The results revealed the benefit of introducing heat conduction networks in the densification of composites. The maximum bending strength and interlaminar shear strength of the modified composites reached 568.67 MPa and 68.48 MPa, respectively. These values were equivalent to 18.6% and 69.4% increase compared to those of composites without channels. However, channels in thickness direction destroyed the continuity of fibers and matrix, creating numerous defects. As the volume fraction of heat conduction channels rose, the pinning strengthening effect of channels and influence of defects competed with each other to result in first enhanced mechanical properties followed by a decline. The in-plane thermal conductivity was found anisotropic with a maximum value reaching 86.20 W/(m·K) after introducing pitch-based carbon unidirectional tapes. The thermal conductivity in thickness direction increased with volume fraction of pitch-based carbon fibers and reached 19.13 W/(m·K) at 3.87 vol% pitch-based carbon fibers in the thickness direction. This value was 90.75% higher than that of composites without channels.     

Homogeneous Fabrication of Al2O3–ZrO2–SiC Whisker Composite by Surface-Induced Coating

Al₂O₃–ZrO₂–SiC whisker composites were prepared by surface-induced coating of the precursor for the ZrO₂ phase on the kinetically stable colloid particles of Al₂O₃ and SiC whisker. The fabricated composites were characterized by a uniform spatial distribution of ZrO₂ and SiC whisker phases throughout the Al₂O₃ matrix. The fracture toughness values of the Al₂O₃–15 vol% ZrO₂–20 vol% SiC whisker composites (∼12 MPa.m^1/2) are substantially greater than those of comparable Al₂O₃–SiC whisker composites, indicating that both the toughening resulting from the process zone mechanism and that caused by the reinforced SiC whiskers work simultaneously in hot-pressed composites.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Fracture of Si3N4–SiC Whisker Composites under Cyclic Loads

This communication demonstrates the role of cyclic compressive loads in inducing mode I fatigue crack growth at room temperature in Si₃N₄ matrix–SiC whisker composite materials containing stress concentrations. The characteristics of stable, cyclic fracture are examined for several volume fractions of the SiC whisker and are compared with those of the matrix material. It is found that the composites with higher volume fractions of SiC whiskers exhibit an inferior resistance to fracture under cyclic compressive loads despite improvements in fracture toughness values.     

Elastic Properties of Al2O3 and Si3N4 Matrix Composites with SiC Whisker Reinforcement

A study of the elastic moduli of Al₂O₃ and Si₃N₄ ceramics reinforced with 0 to 25 wt% SiC whiskers has been performed. The Young's moduli, shear moduli, and longitudinal modulus are compared with calculated predictions for aligned fiber composites by Hill and Hashin and Rosen, and for fibers randomly oriented in three dimensions by Christensen and Waal. The measured values are in excellent quantitative agreement with those derived for the random orientation of the SiC whiskers.     

Role of the Interfacial Thermal Barrier in the Effective Thermal Diffusivity/Conductivity of SiC-Fiber-Reinforced Reaction-Bonded Silicon Nitride

Experimental thermal diffusivity data transverse to the fiber direction for composites composed of a reaction bonded silicon nitride matrix reinforced with uniaxially aligned carbon-coated silicon carbide fibers indicate the existence of a significant thermal barrier at the matrix-fiber interface. Calculations of the interfacial thermal conductances indicate that at 300°C and 1-atm N₂, more than 90% of the heat conduction across the interface occurs by gaseous conduction. The magnitude of the interfacial conductance is decreased significantly under vacuum or by removal of the carbon surface layer from the fibers by selective oxidation. Good agreement is obtained between thermal conductance values for the oxidized composite at 1 atm calculated from the thermal conductivity of the N₂ gas and those inferred from the data for the effective composite thermal conductivity.     

Thermal and Electric Properties in Hot-Pressed ZrB2–MoSi2–SiC Composites

The thermal and electrical properties of MoSi₂ and/or SiC-containing ZrB₂-based composites and the effects of MoSi₂ and SiC contents were examined in hot-pressed ZrB₂–MoSi₂–SiC composites. The thermal conductivity and electrical conductivity of the ZrB₂–MoSi₂–SiC composites were measured at room temperature by a nanoflash technique and a current–voltage method, respectively. The results indicate that the thermal and electrical conductivities of ZrB₂–MoSi₂–SiC composites are dependent on the amount of MoSi₂ and SiC. The thermal conductivities observed for all of the compositions were more than 75 W·(m·K)⁻¹. A maximum conductivity of 97.55 W·(m·K)⁻¹ was measured for the 20 vol% MoSi₂-30 vol% SiC-containing ZrB₂ composite. On the other hand, the electrical conductivities observed for all of the compositions were in the range from 4.07 × 10–8.11 × 10 Ω⁻¹·cm⁻¹.