Degradation of sulfamethoxazole in water by solar photo-Fenton. Chemical and toxicological evaluation

In this work, the photocatalytic degradation of the antibiotic sulfamethoxazole (SMX) by solar photo-Fenton at pilot plant scale was evaluated in distilled water (DW) and in seawater (SW). Degradation and mineralization of SMX were strongly hindered in SW compared to DW. The influence of H₂O₂ and iron concentration on the efficiency of the photocatalytic process was evaluated. An increase in iron concentration from 2.6 to 10.4 mg L⁻¹ showed only a slight improvement in SMX degradation and mineralization. However, an increase in H₂O₂ concentration up to 120 mg L⁻¹ during photo-Fenton in DW decreased SMX solution toxicity from 85% to 20%, according to results of Daphnia magna bioassays. The same behaviour was not observed after photo-Fenton treatment in SW. Despite 45% mineralization in SW, toxicity increased from 16% to 86% as shown by Vibrio fischeri bioassays, which suggests that the intermediates generated in SW are different from those in DW. A SMX degradation pathway during the photo-Fenton treatment in DW is proposed.     

Effect of pesticide concentration on the degradation process by combined solar photo-Fenton and biological treatment

The influence of pesticide concentration, expressed as dissolved organic carbon (DOC), on combined solar photo-Fenton and biological oxidation treatment was studied using wastewater containing a mixture of five commercial pesticides, Vydate, Metomur, Couraze, Ditumur and Scala. Two initial DOC concentrations, 200 mg L⁻¹ and 500 mg L⁻¹ were assayed. Variation in biodegradability with photocatalytic treatment intensity was tested using Pseudomonas putida. Thus the mineralisation required for combining with biodegradation of intermediates by activated sludge was 33% and 55% at 200 mg L⁻¹ and 500 mg L⁻¹, respectively. Biotreatment was carried out in a stirred tank in sequencing batch reactor (SBR) mode. As revealed by the biodegradation kinetics, intermediates generated at the higher pesticide concentration caused lower carbon removal rates in spite of the longer photo-Fenton treatment time applied. One strategy for treating water with high concentrations of pesticides and overcoming the low biodegradability of photo-Fenton intermediates is to mix it with a biodegradable carbon source before biological oxidation. This combination of photo-Fenton and acclimatized activated sludge in several SBR cycles led to complete biodegradation of a concentrated pesticide solution of 500 mg L⁻¹ DOC in 5 h with a carbon removal efficiency of 90%.     

Degradation of fifteen emerging contaminants at μg L initial concentrations by mild solar photo-Fenton in MWTP effluents

The degradation of 15 emerging contaminants (ECs) at low concentrations in simulated and real effluent of municipal wastewater treatment plant with photo-Fenton at unchanged pH and Fe = 5 mg L⁻¹ in a pilot-scale solar CPC reactor was studied. The degradation of those 15 compounds (Acetaminophen, Antipyrine, Atrazine, Caffeine, Carbamazepine, Diclofenac, Flumequine, Hydroxybiphenyl, Ibuprofen, Isoproturon, Ketorolac, Ofloxacin, Progesterone, Sulfamethoxazole and Triclosan), each with an initial concentration of 100 μg L⁻¹, was found to depend on the presence of CO₃²⁻ and HCO₃⁻ (hydroxyl radicals scavengers) and on the type of water (simulated water, simulated effluent wastewater and real effluent wastewater), but is relatively independent of pH, the type of acid used for release of hydroxyl radicals scavengers and the initial H₂O₂ concentration used. Toxicity tests with Vibrio fisheri showed that degradation of the compounds in real effluent wastewater led to toxicity increase.     

Decontamination industrial pharmaceutical wastewater by combining solar photo-Fenton and biological treatment

Characterization and treatment of a real pharmaceutical wastewater containing 775 mg dissolved organic carbon per liter by a solar photo-Fenton/biotreatment were studied. There were also many inorganic compounds present in the matrix. The most important chemical in this wastewater was nalidixic acid (45 mg/L), an antibiotic pertaining to the quinolone group. A Zahn-Wellens test demonstrated that the real bulk organic content of the wastewater was biodegradable, but only after long biomass adaptation; however, the nalidixic acid concentration remained constant, showing that it cannot be biodegraded. An alternative is chemical oxidation (photo-Fenton process) first to enhance biodegradability, followed by a biological treatment (Immobilized Biomass Reactor - IBR). In this case, two studies of photo-Fenton treatment of the real wastewater were performed, one with an excess of H₂O₂ (kinetic study) and another with controlled H₂O₂ dosing (biodegradability and toxicity studies). In the kinetic study, nalidixic acid completely disappeared after 190 min. In the other experiment with controlled H₂O₂, nalidixic acid degradation was complete at 66 mM of H₂O₂ consumed. Biodegradability and toxicity bioassays showed that photo-Fenton should be performed until total degradation of nalidixic acid before coupling a biological treatment. Analysis of the average oxidation state (AOS) demonstrated the formation of more oxidized intermediates. With this information, the photo-Fenton treatment time (190 min) and H₂O₂ dose (66 mM) necessary for adequate biodegradability of the wastewater could be determined. An IBR operated in batch mode was able to reduce the remaining DOC to less than 35 mg/L. Ammonium consumption and NO₃⁻ generation demonstrated that nitrification was also attained in the IBR. Overall DOC degradation efficiency of the combined photo-Fenton and biological treatment was over 95%, of which 33% correspond to the solar photochemical process and 62% to the biological treatment.     

Biodegradability enhancement of a pesticide-containing bio-treated wastewater using a solar photo-Fenton treatment step followed by a biological oxidation process

This work proposes an efficient combined treatment for the decontamination of a pesticide-containing wastewater resulting from phytopharmaceutical plastic containers washing, presenting a moderate organic load (COD = 1662-1960 mg O₂ L⁻¹; DOC = 513-696 mg C L⁻¹), with a high biodegradable organic carbon fraction (81%; BOD₅ = 1350-1600 mg O₂ L⁻¹) and a remaining recalcitrant organic carbon mainly due to pesticides. Nineteen pesticides were quantified by LC-MS/MS at concentrations between 0.02 and 45 mg L⁻¹ (14-19% of DOC). The decontamination strategy involved a sequential three-step treatment: (a) biological oxidation process, leading to almost complete removal of the biodegradable organic carbon fraction; (b) solar photo-Fenton process using CPCs, enhancing the bio-treated wastewater biodegradability, mainly due to pesticides degradation into low-molecular-weight carboxylate anions; (c) and a final polishing step to remove the residual biodegradable organic carbon, using a biological oxidation process. Treatment performance was evaluated in terms of mineralization degree (DOC), pesticides content (LC-MS/MS), inorganic ions and low-molecular-weight carboxylate anions (IC) concentrations. The estimated phototreatment energy necessary to reach a biodegradable wastewater, considering pesticides and low-molecular-weight carboxylate anions concentrations, Zahn-Wellens test and BOD₅/COD ratio, was only 2.3 kJ_UV L⁻¹ (45 min of photo-Fenton at a constant solar UV power of 30 W m⁻²), consuming 16 mM of H₂O₂, which pointed to 52% mineralization and an abatement higher than 86% for 18 pesticides. The biological oxidation/solar photo-Fenton/biological oxidation treatment system achieved pesticide removals below the respective detection limits and 79% mineralization, leading to a COD value lower than 150 mg O₂ L⁻¹, which is in agreement with Portuguese discharge limits regarding water bodies.     

Degradation of the emerging contaminant ibuprofen in water by photo-Fenton

In this study the degradation of the worldwide Non-Steroidal Anti-Inflammatory Drug (NSAID) ibuprofen (IBP) by photo-Fenton reaction by use of solar artificial irradiation was carried out. Non-photocatalytic experiments (complex formation, photolysis and UV/Vis-H₂O₂ oxidation) were executed to evaluate the isolated effects and additional differentiated degradation pathways of IBP. The solar photolysis cleavage of H₂O₂ generates hydroxylated-IBP byproducts without mineralization. Fenton reaction, however promotes hydroxylation with a 10% contamination in form of a mineralization. In contrast photo-Fenton in addition promotes the decarboxylation of IBP and its total depletion is observed. In absence of H₂O₂ a decrease of IBP was observed in the Fe(II)/UV-Vis process due to the complex formation between iron and the IBP-carboxylic moiety. The degradation pathway can be described as an interconnected and successive principal decarboxylation and hydroxylation steps. TOC depletion of 40% was observed in photo-Fenton degradation. The iron-IBP binding was the key-point of the decarboxylation pathway. Both decarboxylation and hydroxylation mechanisms, as individual or parallel process are responsible for IBP removal in Fenton and photo-Fenton systems. An increase in the biodegradability of the final effluent after photo-Fenton treatment was observed. Final BOD₅ of 25 mg L⁻¹ was reached in contrast to the initial BOD₅ shown by the untreated IBP solution (BOD₅ < 1 mg L⁻¹). The increase in the biodegradability of the photo-Fenton degradation byproducts opens the possibility for a complete remediation with a final post-biological treatment.     

Solar photo-Fenton process on the abatement of antibiotics at a pilot scale: Degradation kinetics, ecotoxicity and phytotoxicity assessment and removal of antibiotic resistant enterococci

This work investigated the application of a solar driven advanced oxidation process (solar photo-Fenton), for the degradation of antibiotics at low concentration level (μg L⁻¹) in secondary treated domestic effluents at a pilot-scale. The examined antibiotics were ofloxacin (OFX) and trimethoprim (TMP). A compound parabolic collector (CPC) pilot plant was used for the photocatalytic experiments. The process was mainly evaluated by a fast and reliable analytical method based on a UPLC-MS/MS system. Solar photo-Fenton process using low iron and hydrogen peroxide doses ([Fe²⁺]₀ = 5 mg L⁻¹; [H₂O₂]₀ = 75 mg L⁻¹) was proved to be an efficient method for the elimination of these compounds with relatively high degradation rates. The photocatalytic degradation of OFX and TMP with the solar photo-Fenton process followed apparent first-order kinetics. A modification of the first-order kinetic expression was proposed and has been successfully used to explain the degradation kinetics of the compounds during the solar photo-Fenton treatment. The results demonstrated the capacity of the applied advanced process to reduce the initial wastewater toxicity against the examined plant species (Sorghum saccharatum, Lepidium sativum, Sinapis alba) and the water flea Daphnia magna. The phytotoxicity of the treated samples, expressed as root growth inhibition, was higher compared to that observed on the inhibition of seed germination. Enterococci, including those resistant to OFX and TMP, were completely eliminated at the end of the treatment. The total cost of the full scale unit for the treatment of 150 m³ day⁻¹ of secondary wastewater effluent was found to be 0.85 € m⁻³.     

Biological removal of phenol from strong wastewaters using a novel MSBR

In this study, the performance of a moving-bed sequencing batch reactor (MSBR) that removes phenol from wastewater is presented. The effects of phenol concentration (50-3325 mg L⁻¹), filling time (0-4 h) and aerating time (4-18 h) on the performance of the MSBR are given in terms of phenol and COD removal efficiencies. Moreover, the effect of the moving media on the overall performance of the reactor is also determined. The reactor can completely remove phenol and COD at inlet concentrations up to 3000 mg phenol L⁻¹ (6780 mg COD L⁻¹), which was the inhibition concentration, and with a 24-h cycle time. The filling time range tested here did not significantly affect phenol or COD removal. The optimum hydraulic retention time (HRT) for the MSBR is 40 h and the critical phenol loading rate is 83.4 g phenol m⁻³ h⁻¹, which gives a phenol removal efficiency of 99%. The reactor can also withstand shock loads from slug feeding. The moving bed contribution to phenol and COD removal efficiencies was up to 28.1 and 34.7%, respectively, at the phenol loading rate of 83.4 g m⁻³ h⁻¹. The findings of this investigation suggest that MSBR can be a robust and promising process for effectively treating wastewaters containing inhibitor or recalcitrant compounds in industrial settings.     

Degradation of DBPs' precursors in river water before and after slow sand filtration by photo-Fenton process at pH 5 in a solar CPC reactor

The generation of disinfection by-products during water treatment can be controlled by reducing the levels of precursor species prior to the chlorination step. The Natural Organic Matter (NOM) is the principal organic precursor and conventional removal of pollutants such as coagulation, flocculation and filtration do not guarantee the total NOM removal. In this study the degradation of NOM model compounds (dihydroxy-benzene) as well as the removal of NOM from river water via photo-Fenton process in a CPC solar photo-reactor is presented. The effect of solar activated photo-Fenton reagent at pH 5.0 before and after a slow sand filtration (SSF) in waters containing natural iron species is investigated and the details reported. The results showed that the total transformation of dihydroxy-benzene compounds along a mineralization higher than 80% was obtained. The mineralization of the organic compounds dissolved in natural water was higher than in Milli-Q water, suggesting that the aqueous organic and inorganic components (metals, humic acids and photoactive species) positively affect the photocatalytic process. When 1.0 mg/L of Fe³⁺ is added to the system, the photo-Fenton degradation was improved. Therefore the photo-Fenton reagent could be an interesting complement to other processes for NOM removal. Comparing the response of two rivers as media for the organic compounds degradation it was observed that the NOM photo-degradation rate depends of the water composition.     

Characterization of the degradation performance of the sulfamethazine antibiotic by photo-Fenton process

The present study provides results describing the degradation performance of the Sulfamethazine (SMT) antibiotic via photo-Fenton treatment. Experiments were carried out using 1 L solution samples of SMT (50 mg L⁻¹) under different conditions. HPLC results reveal that both Fenton and photo-Fenton reactions were able to completely remove SMT antibiotic from the studied samples in less than 2 min treatment. Half-life times and kinetic parameters (assuming a pseudo-first-order kinetics at reaction initial stage, far from the equilibrium) for SMT degradation were determined and discussed. Hence, appropriate Fenton reagent loads are given to attain different targets proposed. TOC and HPLC data also revealed the presence of reaction intermediates; thus toxicity assays were performed regarding bacterial growth rate. The toxicity of an SMT solution was shown to increase during its degradation by means of photo-Fenton reactions.     

Performance of a Sequencing Batch Biofilm Reactor for the treatment of pre-oxidized Sulfamethoxazole solutions

A combined strategy of a photo-Fenton pretreatment followed by a Sequencing Batch Biofilm Reactor (SBBR) was evaluated for total C and N removal from a synthetic wastewater containing exclusively 200 mg L⁻¹ of the antibiotic Sulfamethoxazole (SMX). Photo-Fenton reaction was optimized at the minimum reagent doses in order to improve the biocompatibility of effluents with the subsequent biological reactor. Consequently, the pretreatment was performed with two different initial H₂O₂ concentrations (300 and 400 mg L⁻¹) and 10 mg L⁻¹ of Fe²⁺. The pre-treated effluents with the antibiotic intermediates as sole carbon source were used as feed for the biological reactor. The SBBR was operated under aerobic conditions to mineralize the organic carbon, and the Hydraulic Retention Time (HRT) was optimized down to 8 h reaching a removal of 75.7% of the initial Total Organic Carbon (TOC). The total denitrification of the NO₃⁻ generated along the chemical-biological treatment was achieved by means of the inclusion of a 24-h anoxic stage in the SBBR strategy. In addition, the Activated Sludge Model No. 1 (ASM1) was successfully used to complete the N balance determining the N fate in the SBBR.The characterization and the good performance of the SBBR allow presenting the assessed combination as an efficient way for the treatment of wastewaters contaminated with biorecalcitrant pharmaceuticals as the SMX.     

Granulation of activated sludge in a pilot-scale sequencing batch reactor for the treatment of low-strength municipal wastewater

Aerobic granulation of activated sludge was achieved in a pilot-scale sequencing batch reactor (SBR) for the treatment of low-strength municipal wastewater (<200 mg L⁻¹ of COD, chemical oxygen demand). The volume exchange ratio and settling time of an SBR were found to be two key factors in the granulation of activated sludge grown on the low-strength municipal wastewater. After operation of 300 days, the mixed liquor suspended solids (MLSS) concentration in the SBR reached 9.5 g L⁻¹ and consisted of approximate 85% granular sludge. The average total COD removal efficiency kept at 90% and NH₄⁺-N was almost completely depleted (∼95%) after the formation of aerobic granules. The granules (with a diameter over 0.212 mm) had a diameter ranging from 0.2 to 0.8 mm and had good settling ability with a settling velocity of 18-40 m h⁻¹. Three bacterial morphologies of rod, coccus and filament coexisted in the granules. Mathematical modeling was performed to get insight into this pilot-scale granule-based reactor. The modified IWA activated sludge model No 3 (ASM3) was able to adequately describe the pilot-scale SBR dynamics during its cyclic operation.     

Synergetic effect between photocatalytic degradation and adsorption processes on the removal of phenolic compounds from olive mill wastewater

The photocatalytic degradation of two phenolic compounds, p-coumaric acid and caffeic acid, was performed with a suspended mixture of TiO₂ and powdered activated carbon (PAC) (at pH = 3.4 and 8). Adsorption, direct photolysis and photocatalytic degradation were studied under different pH and UV light sources (sunlight vs. 365 nm UV lamps). The potential for reusing this catalyst mixture in sequential photocatalytic runs was examined as well. Quantum yields for the direct photolysis of caffeic acid under solar and artificial 365 nm light were calculated (for the first time) as 0.005 and 0.011, respectively.A higher removal rate of contaminants by either adsorption or photocatalysis was obtained at a low pH (pH 4). Furthermore, the addition of PAC increased the removal efficiency of the phenolic compounds. Fast removal of the pollutants from the solution over three sequential runs was achieved only when both TiO₂ and PAC were present. This suggests that at medium phenolic concentrations, the presence of PAC as a co-sorbent reduces surface poisoning of the TiO₂ catalyst and hence improves photocatalysis degradation of phenolic pollutants.The adsorption equilibrium of caffeic acid or p-coumaric acid on TiO₂, PAC and the combined mixture of TiO₂ and PAC follows the Langmuir isotherm model. Experiments with PAC TiO₂ mixture and olive mill wastewater (anaerobically treated and diluted by a factor of 10) showed higher removal of polyphenols than of chemical oxygen demand (COD). 87% removal of total polyphenols, compared to 58% of COD, was achieved after 24 h of exposure to 365 nm irradiation (7.6 W/m²) in the presence of a suspended mixture of TiO₂ and PAC, indicating “self-selectivity” of polyphenols.     

Solar treatment of cork boiling and bleaching wastewaters in a pilot plant

This paper reports on cork boiling and bleaching wastewaters treatment by solar photocatalytic processes, TiO₂/UV and Fe²⁺/H₂O₂/UV (TiO₂-only for bleaching wastewater), in a pilot plant with compound parabolic collectors. The photo-Fenton reaction (k = 0.12 L/kJ_UV, r₀ = 59.4 mg/kJ_UV) is much more efficient that TiO₂ photocatalysis and TiO₂ + S₂O₈²⁻ (k = 0.0024 L/kJ_UV, r₀ = 1.36 mg/kJ_UV), leading to 94% mineralization of the bleaching wastewater after 31.5 kJ_UV/L, consuming 77.1 mM of H₂O₂ (3.0 mmol/kJ_UV) and using 20 mg/L of iron. For the cork boiling wastewater, after a slow initial reaction rate, the DOC degradation curve shows a first-order kinetics behaviour (k = 0.015 L/kJ_UV, r₀ = 20.8 mg/kJ_UV) until 173 kJ_UV/L (≈300 mg C/L). According to the average oxidation state (AOS), toxicity profiles, respirometry and kinetic results obtained in two solar CPCs plants, the optimal energy dose estimated for phototreatment to reach a biodegradable effluent is 15 kJ_UV/L and 114 kJ_UV/L, consuming 33 mM and 151 mM of H₂OT:/PGN/ELSEVIER/WR/web/00007490/₂, achieving almost 49% and 48% mineralization of the wastewaters, respectively for the cork bleaching and boiling wastewaters.     

Efficient electricity production and simultaneously wastewater treatment via a high-performance photocatalytic fuel cell

A great quantity of wastewater were discharged into water body, causing serious environmental pollution. Meanwhile, the organic compounds in wastewater are important sources of energy. In this work, a high-performance short TiO₂ nanotube array (STNA) electrode was applied as photoanode material in a novel photocatalytic fuel cell (PFC) system for electricity production and simultaneously wastewater treatment. The results of current work demonstrate that various model compounds as well as real wastewater samples can be used as substrates for the PFC system. As a representative of model compounds, the acetic acid solution produces the highest cell performance with short-circuit current density 1.42 mA cm⁻², open-circuit voltage 1.48 V and maximum power density output 0.67 mW cm⁻². The STNA photoanode reveals obviously enhanced cell performance compared with TiO₂ nanoparticulate film electrode or other long nanotubes electrode. Moreover, the photoanode material, electrolyte concentration, pH of the initial solution, and cathode material were found to be important factors influencing the system performance of PFC. Therefore, the proposed fuel cell system provides a novel way of energy conversion and effective disposal mode of organics and serves well as a promising technology for wastewater treatment.     

Enhancing biodegradability of priority substances (pesticides) by solar photo-Fenton

In this paper, we present the photo-Fenton treatment in a solar pilot-plant scale of several EU priority hazardous substances (Alachlor, Atrazine, Chlorfenvinphos, Diuron and Isoproturon) dissolved in water. The results have been evaluated not only from the point of view of contaminant disappearance and mineralisation, but also of toxicity reduction and enhancement of biodegradability. Degradation was monitored by total organic carbon, pesticide concentration by HPLC-UV, inorganics released by ion chromatography, and biodegradability by the Zahn-Wellens (Z-W) test. The total volume of the solar photoreactor, composed of compound parabolic collectors with a total area of 4.16m2, was between 70 and 82 L. The treatment was shown to be effective, mineralising all of the pesticides tested, both alone and in mixtures. In order to find out the conditions for biocompatibility using the photo-Fenton reaction as a pre-treatment step, wastewater inoculated with unacclimated municipal sludge containing pesticides after certain degradation time was evaluated by the Z-W test. Biodegradability was enhanced (70% considered biodegradable) by the photo-Fenton treatment after 12-25min. It may be concluded that the photo-Fenton treatment consistently enhances biodegradability of wastewater containing pesticides.     

Biotreatment and bioassessment of heavy metal removal by sulphate reducing bacteria in fixed bed reactors

In this work a batch-optimised mixture (w/w %: 6% leaves, 9% compost, 3% Fe(0), 30% silica sand, 30% perlite, 22% limestone) was investigated in a continuous fixed bed column reactor for the treatment of synthetic acid-mine drainage (AMD). A column reactor was inoculated with sulphate-reducing bacteria and fed with a solution containing sulphate and heavy metals (As(V), Cd, Cr(VI), Cu and Zn). At steady state, sulphate abatement was 50 ± 10%, while metals were totally removed. A degradation rate constant (k) of 0.015 ± 0.001 h⁻¹ for sulphate removal was determined from column data by assuming a first order degradation rate. Reduction of AMD toxicity was assessed by using the nematode Caenorhabditis elegans as a test organism. A lethality assay was performed with the toxicants before and after the treatment, showing that only 5% of the animals were still alive after 48 h in presence of the contaminants, while the percentage increased to 73% when the nematodes were exposed to the solution eluted from the column.     

The development of a novel hybrid aerating membrane-anaerobic baffled reactor for the simultaneous nitrogen and organic carbon removal from wastewater

A novel hybrid aerating membrane-anaerobic baffled reactor (HMABR), based on the installation of aerating membrane into an anaerobic baffled reactor (ABR), to achieve simultaneous removal of nitrogenous and carbonaceous organic pollutants was developed in this study. The results demonstrated that after the installation of membrane module, total VFA and COD concentration in the HMABR effluent were decreased by 68.1 and 59.5% respectively, with increased nitrogenous pollutant remove efficiency by 83.5%, at influent COD concentration of 1600 mg/L and NH₄⁺-N concentration of 80 mg/L. Fluorescence in situ hybridization (FISH) results of the aerating membrane biofilm showed that the biofilm stratification for the spatial profiles of ammonia-oxidizing bacteria, nitrite-oxidizing bacteria, aerobic heterotrophic bacteria, and denitrifying bacteria. The potential usage of HMABR widens the usage of aerobic-anaerobic combination technology for industrial wastewater treatment.     

Influence of pharmaceutical residues on the structure of activated sludge bacterial communities in wastewater treatment bioreactors

Concern is growing over contamination of the environment with pharmaceuticals because of their widespread use and incomplete removal during wastewater treatment, where microorganisms drive the key processes. The influence of pharmaceuticals on bacterial community structure in activated sludge was assessed in small-scale wastewater treatment bioreactors containing different concentrations (5, 50, 200 and 500 μg L⁻¹) of several commonly used pharmaceuticals (ibuprofen, naproxen, ketoprofen, diclofenac and clofibric acid). T-RFLP analyses of the bacterial 16S rRNA genes indicated a minor but consistent shift in the bacterial community structure in the bioreactor R50 supplied with pharmaceuticals at a concentration of 50 μg L⁻¹, compared to the control reactor R0, which was operated without addition of pharmaceuticals. In the reactors operated with higher concentrations of pharmaceuticals, a greater structural divergence was observed. Bacterial community composition was further investigated by preparation of two clone libraries of bacterial 16S rRNA genes from reactors R0 and R50. Most clones in both libraries belonged to the Betaproteobacteria, among which Thauera, Sphaerotilus, Ideonella and Acidovorax-related spp. dominated. Nitrite-oxidizing bacteria of the genus Nitrospira sp., which are key organisms for the second stage of nitrification in wastewater treatment plants, were found only in the clone library of the reactor without pharmaceuticals. In addition, diversity indices were calculated for the two clone libraries, indicating a reduced diversity of activated sludge bacterial community in the reactor supplied with 50 μg L⁻¹ of each of selected pharmaceuticals.     

Treatment of a sanitary landfill leachate using combined solar photo-Fenton and biological immobilized biomass reactor at a pilot scale

A solar photo-Fenton process combined with a biological nitrification and denitrification system is proposed for the decontamination of a landfill leachate in a pilot plant using photocatalytic (4.16 m² of Compound Parabolic Collectors - CPCs) and biological systems (immobilized biomass reactor). The optimum iron concentration for the photo-Fenton reaction of the leachate is 60 mg Fe²⁺ L⁻¹. The organic carbon degradation follows a first-order reaction kinetics (k = 0.020 L kJ_UV⁻¹, r₀ = 12.5 mg kJ_UV⁻¹) with a H₂O₂ consumption rate of 3.0 mmol H₂O₂ kJ_UV⁻¹. Complete removal of ammonium, nitrates and nitrites of the photo-pre-treated leachate was achieved by biological denitrification and nitrification, after previous neutralization/sedimentation of iron sludge (40 mL of iron sludge per liter of photo-treated leachate after 3 h of sedimentation). The optimum C/N ratio obtained for the denitrification reaction was 2.8 mg CH₃OH per mg N-NO₃⁻, consuming 7.9 g/8.2 mL of commercial methanol per liter of leachate. The maximum nitrification rate obtained was 68 mg N-NH₄⁺ per day, consuming 33 mmol (1.3 g) of NaOH per liter during nitrification and 27.5 mmol of H₂SO₄ per liter during denitrification. The optimal phototreatment energy estimated to reach a biodegradable effluent, considering Zahn-Wellens, respirometry and biological oxidation tests, at pilot plant scale, is 29.2 kJ_UV L⁻¹ (3.3 h of photo-Fenton at a constant solar UV power of 30 W m⁻²), consuming 90 mM of H₂O₂ when used in excess, which means almost 57% mineralization of the leachate, 57% reduction of polyphenols concentration and 86% reduction of aromatic content.