Improvement of Thermoelectric Power Factor of Hydrothermally Prepared Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Compared with its Solvothermally Prepared Counterpart

We report on the successful hydrothermal synthesis of Bi_0.5Sb_1.5Te₃, using water as the solvent. The products of the hydrothermally prepared Bi_0.5 Sb_1.5Te₃ were hexagonal platelets with edges of 200–1500 nm and thicknesses of 30–50 nm. Both the Seebeck coefficient and electrical conductivity of the hydrothermally prepared Bi_0.5Sb_1.5Te₃ were larger than those of the solvothermally prepared counterpart. Hall measurements of Bi_0.5Sb_1.5Te₃ at room temperature indicated that the charge carrier was p-type, with a carrier concentration of 9.47 × 10¹⁸ cm⁻³ and 1.42 × 10¹⁹ cm⁻³ for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively. The thermoelectric power factor at 290 K was 10.4 μW/cm K² and 2.9 μW/cm K² for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively.     

Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Superlattices Grown by Nanoalloying

In this work, Bi₂Te₃-Sb₂Te₃ superlattices were prepared by the nanoalloying approach. Very thin layers of Bi, Sb, and Te were deposited on cold substrates, rebuilding the crystal structure of V₂VI₃ compounds. Nanoalloyed super- lattices consisting of alternating Bi₂Te₃ and Sb₂Te₃ layers were grown with a thickness of 9 nm for the individual layers. The as-grown layers were annealed under different conditions to optimize the thermoelectric parameters. The obtained layers were investigated in their as-grown and annealed states using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive x-ray (EDX) spectroscopy, transmission electron microscopy (TEM), and electrical measurements. A lower limit of the elemental layer thickness was found to have c-orientation. Pure nanoalloyed Sb₂Te₃ layers were p-type as expected; however, it was impossible to synthesize p-type Bi₂Te₃ layers. Hence the Bi₂Te₃-Sb₂Te₃ superlattices consisting of alternating n- and p-type layers showed poor thermoelectric properties.     

Magnetic susceptibility of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> alloys

The magnetic susceptibility of Czochralski-grown single crystals of Bi₂Te₃-Sb₂Te₃ alloys containing 0, 10, 25, 40, 50, 60, 65, 70, 80, 90, 99.5, or 100 mol % Sb₂Te₃ has been investigated. The magnetic susceptibility of these crystals was determined at the temperature T = 291 K and the magnetic field H oriented parallel (χ_‖) and perpendicularly (χ_⊥) to the trigonal crystallographic axis C ₃. A complicated concentration dependence of the anisotropy of magnetic susceptibility χ_‖/χ_⊥ has been revealed. The crystals with the free carrier concentration p ≈ 5 × 10¹⁹ cm^?3 do not exhibit anisotropy of magnetic susceptibility. The transition to the isotropic magnetic state occurs for the compositions characterized by a significantly increased (from 200 to 300 meV) optical bandgap.     

The effect of irradiation with electrons on the electrical parameters of Hg<Subscript>3</Subscript>In<Subscript>2</Subscript>Te<Subscript>6</Subscript>

The results of studying the electrical properties of Hg₃In₂Te₆ crystals irradiated with electrons with the energy E _e = 18 MeV and the dose D = 4 × 10¹⁶ cm⁻² are reported. It is shown that, irrespective of the charge-carrier concentration in the initial material, the Hg₃In₂Te₆ samples acquire the charge-carrier concentration (1.6–1.8) × 10¹³ cm⁻³ after irradiation. The phenomenon of Fermi level pinning in an irradiated material is discussed. The initial charge-carrier concentration, which remains virtually unchanged after irradiation and which ensures the high radiation resistance of Hg₃In₂Te₆ crystals, corresponds to a compensated material, similar to an intrinsic semiconductor at T > 260 K.     

Doping of the Bi<Subscript>1.9</Subscript>Sb<Subscript>0.1</Subscript>Te<Subscript>3</Subscript> solid solution with Sn impurity

In (Bi_1.9Sb_0.1)_{1 − x} Sn _x Te₃ solid solution with different contents of Sn, the electrical conductivity (σ₁₁) and the Hall (R ₁₂₃ and R ₃₂₁), Seebeck (S ₁₁ and S ₃₃), and Nernst-Ettingshausen (Q ₁₂₃ and Q ₃₂₁) coefficients have been measured. It is shown that doping with tin strongly modifies temperature dependences of the kinetic coefficients. The effect of tin on electrical homogeneity of the samples has been studied: with increasing number of Sn atoms embedded, crystals become more homogeneous. These features indicate the presence of the quasi-local states of Sn in the valence band of Bi_1.9Sb_0.1Te₃. Within a one-band model, we estimated the effective mass of the density of hole states (m _d ), the energy gap extrapolated to 0 K (E _g0 = 0.20–0.25 eV), the energy of impurity states (E _Sn ≈ 40–45 meV), and the scattering parameter (r ≈ 0.1–0.4). Numerical values of the scattering parameter indicate a mixed mechanism of scattering in the samples under investigation with dominant scattering at acoustic phonons. With increasing content of tin in the samples, the contribution of impurity scattering increases.     

Conductivity of layers of a chalcogenide glassy semiconductor Ge<Subscript>2</Subscript>Sb<Subscript>2</Subscript>Te<Subscript>5</Subscript> in high electric fields

Effect of high electric fields on the conductivity of 0.5-1-μm-thick layers of a chalcogenide glassy semiconductor with a composition Ge₂Sb₂Te₅, used in phase memory cells, has been studied. It was found that two dependences are observed in high fields: dependence of the current I on the voltage U, of the type I ∝ U ⁿ , with the exponent (n ≈ 2) related to space-charge-limited currents, and a dependence of the conductivity σ on the field strength F of the type σ = σ₀exp(F/F ₀) (where F ₀ = 6 × 10⁴ V cm⁻¹), caused by ionization of localized states. A mobility of 10⁻³–10⁻² cm² V⁻¹ s⁻¹ was determined from the space-charge-limited currents.     

Influence of Element Substitution on Corrosion Behavior of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Compounds

Atmospheric water may condense on the surface of Bi₂Te₃-based compounds constituting the Peltier module, depending on the operating environment used. In the stage of disposal, Bi₂Te₃-based compounds may come into contact with water in waste disposal sites. There are very few publications about the influence of condensed water on Peltier modules. Bi₂Te₃-Sb₂Te₃ or Bi₂Te₃-Bi₂Se₃ pseudo binary system compounds are used as p-type material or n-type material, respectively. The lattice distortion will be induced in the crystal of Bi₂Te₃-based compounds by element substitution due to the reduction in their thermal conductivity. However, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds remains unclear. In this study, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds with practical compositions has been investigated. Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 was prepared by the vertical Bridgman method. The electrochemical properties at room temperature were evaluated by cyclic voltammetry in a standard three-electrode cell. The working electrolyte was a naturally aerated 0.6 or 3.0 mass% NaCl solution. From the tendency for corrosion potential for all the samples, the corrosion sensitivity of ternary compounds was slightly higher than that of binary compounds. From the trend of current density, it was found that Bi_0.5Sb_1.5Te₃ had a corrosion resistance intermediate between Bi₂Te₃ and Sb₂Te₃. On the other hand, corrosion resistance was affected despite a small amount of Se substitution, and the corrosion resistance of Bi₂Te_2.85Se_0.15 was close to or lower than that of Bi₂Se₃. From the observation results of the corrosion products, the trends of morphology and composition of corrosion products for Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 were consistent with those of Sb₂Te₃ or Bi₂Se₃, respectively. From the results of x-ray photoelectron spectroscopy for the electrolyte after testing, the possibility that a corrosion product diffuses to the environment including the salt was suggested in Bi_0.5Sb_1.5Te₃. However, the amount of dissolved corrosion product was very low, and the chemical stability of the corrosion product was not changed or improved by element substitution.     

Electrodeposition of <Emphasis Type="Italic">p</Emphasis>-Type Sb<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Te<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> Thermoelectric Films

Thermoelectric Sb _x Te _y films were potentiostatically electrodeposited in aqueous nitric acid electrolyte solutions containing different concentrations of TeO₂. Stoichiometric Sb _x Te _y films were obtained by applying a voltage of −0.15 V versus saturated calomel electrode (SCE) using a solution consisting of 2.4 mM TeO₂, 0.8 mM Sb₂O₃, 33 mM tartaric acid, and 1 M HNO₃. The nearly stoichiometric Sb₂Te₃ films had a rhombohedral structure, R[`3]m R\bar{3}m , with a preferred orientation along the (015) direction. The films had hole concentration of 5.8 × 10¹⁸/cm³ and exhibited mobility of 54.8 cm²/Vs. A more negative potential resulted in higher Sb content in the deposited Sb _x Te _y films. Furthermore, it was observed that the hole concentration and mobility decreased with increasingly negative deposition potential, and eventually showed insulating properties, possibly due to increased defect formation. The absolute value of the Seebeck coefficient of the as-deposited Sb₂Te₃ thin film at room temperature was 118 μV/K.     

Features of the charge-transport mechanism in layered Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> single crystals doped with chlorine and terbium

The temperature dependences (T = 5−300 K) of the resistivity in the plane of layers and in the direction perpendicular to the layers, as well as the Hall effect and the magnetoresistance (H < 80 kOe, T = 0.5−4.2 K) in Bi₂Te₃ single crystals doped with chlorine and terbium, are investigated. It is shown that the doping of Bi₂Te₃ with terbium atoms results in p-type conductivity and in increasing hole concentration. The doping of Bi₂Te₃ with chlorine atoms modifies also the character of its conductivity instead of changing only the type from p to n. In the temperature dependence of the resistivity in the direction perpendicular to layers, a portion arises with the activation conductivity caused by the hopping between localized states. The charge-transport mechanism in Bi₂Te₃ single crystals doped with chlorine is proposed.     

Effects of SiC Nanodispersion on the Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type and <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Alloys

Polycrystalline p-type Bi_0.5Sb_1.5Te₃ and n-type Bi₂Te_2.7Se_0.3 thermoelectric (TE) alloys containing a small amount (vol.% ≤5) of SiC nanoparticles were fabricated by mechanical alloying and spark plasma sintering. It was revealed that the effects of SiC addition on TE properties can be different between p-type and n-type Bi₂Te₃-based alloys. SiC addition slightly increased the power factor of the p-type materials by decreasing both the electrical resistivity (ρ) and Seebeck coefficient (α), but decreased the power factor of n-type materials by increasing both ρ and α. Regardless of the conductivity type, the thermal conductivity was reduced by dispersing SiC nanoparticles in the Bi₂Te₃-based alloy matrix. As a result, a small amount (0.1 vol.%) of SiC addition increased the maximum dimensionless figure of merit (ZT _max) of the p-type Bi_0.5Sb_1.5Te₃ alloys from 0.88 for the SiC-free sample to 0.97 at 323 K, though no improvement in TE performance was obtained in the case of n-type Bi₂Te_2.7Se_0.3 alloys. Importantly, the SiC-dispersed alloys showed better mechanical properties, which can improve material machinability and device reliability.     

Effects of Cooling Rate on Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>(Se<Subscript>0.4</Subscript>Te<Subscript>0.6</Subscript>)<Subscript>3</Subscript> Compounds

A series of Bi₂(Se_0.4Te_0.6)₃ compounds were synthesized by a rapid route of melt spinning (MS) combined with a subsequent spark plasma sintering (SPS) process. Measurements of the Seebeck coefficient, electrical conductivity, and thermal conductivity were performed over the temperature range from 300 K to 520 K. The measurement results showed that the cooling rate of melt spinning had a significant impact on the transport properties of electrons and phonons, effectively enhancing the thermoelectric properties of the compounds. The maximum ZT value reached 0.93 at 460 K for the sample prepared with the highest cooling rate, and infrared spectrum measurement results showed that the compound with lower tellurium content, Bi₂(Se_0.4Te_0.6)₃, possesses a larger optical forbidden gap (E _g) compared with the traditional n-type zone-melted material with formula Bi₂(Se_0.07Te_0.93)₃. Our work provides a new approach to develop low-tellurium-bearing Bi₂Te₃-based compounds with good thermoelectric performance.     

Influence of Nanoinclusions on Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> Nanocomposites

n-Type Bi₂Te₃ nanocomposites with enhanced figure of merit, ZT, were fabricated by a simple, high-throughput method of mixing nanostructured Bi₂Te₃ particles obtained through melt spinning with micron-sized particles. Moderately high power factors were retained, while the thermal conductivity of the nanocomposites was found to decrease with increasing weight percent of nanoinclusions. The peak ZT values for all the nanocomposites were above 1.1, and the maximum shifted to higher temperature with increasing amount of nanoinclusions. A maximum ZT of 1.18 at 42°C was obtained for the 10 wt.% nanocomposite, which is a 43% increase over the bulk sample at the same temperature. This is the highest ZT reported for n-type Bi₂Te₃ binary material, and higher ZT values are expected if state-of-the-art Bi₂Te_3−x Se _x materials are used.     

Thermal Stability of Ge<Subscript>2</Subscript>Sb<Subscript>2</Subscript>Te<Subscript>5</Subscript> in Contact with Ti and TiN

The thermal stability of a Ge₂Sb₂Te₅ chalcogenide layer in contact with titanium and titanium nitride metallic thin films has been investigated mainly using x-ray diffraction and elastic nuclear backscattering techniques. Without breaking vacuum, Ti and TiN have been deposited on Ge₂Sb₂Te₅ material using magnetron sputtering. Thermal treatments have been performed in a 10⁻⁷ mbar vacuum furnace. On annealing up to 450°C, the TiN metallic film does not interact with the chalcogenide film, but at the same time adhesion problems and instabilities in contact resistance arise. To improve the adhesion and eventually stabilize the contact resistance, an interfacial Ti layer has been considered. At 300°C, a TiTe₂ compound is formed by interacting with Te segregated from the Ge₂Sb₂Te₅ layer. At higher temperatures, the Ti layer decomposes the chalcogenide film, forming several compounds tentatively identified as GeTe, Ge₃Ti₅, Ge₅Ti₆, TiTe_2,, and Sb₂Te₃. It has been found that the properties of the Ge₂Sb₂Te₅ film can be retained by controlling the decomposition rate of the chalcogenide layer, which is achieved by providing a limited supply of Ti and/or by depositing a Te-rich Ge₂Sb₂Te₅ film.     

Microgenerator Using BiSbTe-Pt Thermopile and Pt-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Ceramic Combustor

The performance of a microcombustor thermoelectric generator device based on a thermopile using p-type Bi_0.3Sb_1.7Te₃ (BST) and n-type Pt films has been investigated. The BST films were prepared by two different methods—pulsed laser deposition (PLD) and sputter deposition—on Si₃N₄/SiO₂ multilayers on Si substrate. The ceramic catalyst combustor was patterned on the thermopile end on a thin membrane fabricated by back-side bulk etching of the silicon substrate. At 138°C the thermoelectric power factors of the PLD and sputter-deposited films were 3.6 × 10⁻³ W/mK² and 0.22 × 10⁻³ W/mK², respectively. The power from the generator with the sputter-deposited film was 0.343 μW, which was superior to that of the device with the PLD film, which provided 0.1 μW, for combustion of a 200 sccm flow of 3 v/v% hydrogen in air.     

Thermoelectric Characteristics of <Emphasis Type="Italic">p</Emphasis>-Type (Bi,Sb)<Subscript>2</Subscript>Te<Subscript>3</Subscript>/(Pb,Sn)Te Functional Gradient Materials with Variation of the Segment Ratio

The p-type (Bi,Sb)₂Te₃/(Pb,Sn)Te functional gradient materials (FGMs) were fabricated by hot-pressing mechanically alloyed (Bi_0.2Sb_0.8)₂Te₃ and 0.5 at.% Na₂Te-doped (Pb_0.7Sn_0.3)Te powders together at 500°C for 1 h in vacuum. Segment ratios of (Bi,Sb)₂Te₃ to (Pb,Sn)Te were varied as 3:1, 1.3:1, and 1:1.6. A reaction layer of about 350-μm thickness was formed at the (Bi,Sb)₂Te₃/(Pb,Sn)Te FGM interface. Under temperature differences larger than 340°C applied across a specimen, superior figures of merit were predicted for the (Bi,Sb)₂Te₃/(Pb,Sn)Te FGMs to those of (Bi_0.2Sb_0.8)₂Te₃ and (Pb_0.7Sn_0.3)Te. With a temperature difference of 320°C applied across a specimen, the (Bi,Sb)₂Te₃/(Pb,Sn)Te FGMs with segment ratios of 3:1 and 1.3:1 exhibited the maximum output powers of 72.1 mW and 72.6 mW, respectively, larger than the 63.9 mW of (Bi_0.2Sb_0.8)₂Te₃ and the 26 mW of 0.5 at.% Na₂Te-doped (Pb_0.7Sn_0.3)Te.     

Effect of copper doping on kinetic coefficients and their anisotropy in PbSb<Subscript>2</Subscript>Te<Subscript>4</Subscript>

In anisotropic PbSb₂Te₄ and PbSb₂Te₄:Cu single crystals, nine main independent components of the Hall, electrical-conductivity, thermopower, and Nernst-Ettingshausen effects and their anisotropy in the range 77–450 K have been studied. PbSb₂Te₄ single crystals exhibit a high hole concentration (p ≈ 3 × 10²⁰ cm⁻³). Copper exhibits a donor effect and significantly (approximately by a factor of 2) reduces the hole concentration in PbSb₂Te₄. The temperature dependences of the kinetic coefficients, except for the Hall effect, have a form typical of the one-band model. The significant anisotropy of the Hall coefficient R ₁₂₃/R ₃₂₁ ≈ 2 at low temperatures corresponds to the multi-ellipsoid model of the energy spectrum of holes in PbSb₂Te₄. An important feature of the data on transport phenomena is the high thermopower anisotropy (ΔS ≈ 60–75 μV/K) in the mixed conductivity region caused by the mixed scattering mechanism. Data on the anisotropy of the transverse Nernst-Ettingshausen effect confirm the mixed mechanism of hole scattering; in the cleavage plane, scattering at acoustic phonons dominates, while in the trigonal axis direction, impurity scattering appears significant. Doping with copper enhances the role of impurity scattering in the direction of the trigonal axis c ₃; as a result, two components of the Nernst-Ettingshausen tensor Q ₃₂₁ and Q ₁₃₂ in the PbSb₂Te₄:Cu single crystal are positive at low temperatures, whereas, in the undoped crystal, only the Q ₃₂₁ component is positive.     

Solution-Chemical Syntheses of Nano-Structured Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> and PbTe Thermoelectric Materials

In this work, nano-structured Bi₂Te₃ and PbTe thermoelectric materials were synthesized separately via solvothermal, hydrothermal and low-temperature aqueous chemical routes. X-ray diffraction (XRD), field-emission scanning-electron microscopy (FESEM), transmission electron microscopy (TEM), and energy dispersive spectroscopy (EDS) were used to analyze the powder products. Results showed that the as-prepared Bi₂Te₃ samples were all single-phased and consisted of irregular spherical granules with diameters of ∼30 nm whereas the PbTe samples were mainly composed of well-crystallized cubic crystals with average size of approximately 100 nm. Some nanotubes and nanorods were found in Bi₂Te₃ and PbTe samples, respectively; these were identified as Bi₂Te₃ nanotubes and PbTe nanorods by EDS analysis. Possible reaction mechanisms for these syntheses are discussed in detail herein.     

Electronic Processes in CdIn<Subscript>2</Subscript>Te<Subscript>4</Subscript> Crystals

The results of investigations of electrical, optical, and photoelectric properties of CdIn₂Te⁴ crystals, which were grown by the Bridgman method are presented. It is shown that electrical conductivity is determined mainly by electrons with the effective mass m_n = 0.44m₀ and the mobility 120–140 cm²/(V s), which weakly depends on temperature. CdIn₂Te₄ behaves as a partially compensated semiconductor with the donor-center ionization energy E_d = 0.38 eV and the compensation level K = N_a/N_d = 0.36. The absorption-coefficient spectra at the energy hν < E_g = 1.27 eV are subject to the Urbach rule with a typical energy of 18–25 meV. The photoconductivity depends on the sample thickness. The diffusion length, the charge-carrier lifetime, and the surface-recombination rate are determined from the photoconductivity spectra.     

Response of thermoelectric parameters of Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> films to secondary recrystallization

Flash evaporation is used to grow Bi_0.5Sb_1.5Te₃ films 1200 nm thick on mica substrates. The average lateral crystallite sizes in the as-grown films are ~800 nm. The (0001) plane in the crystallites is preferentially parallel to the substrate plane. After heat treatment in an argon atmosphere, the effective lateral size of crystallites in which the third-order axis is perpendicular to the substrate plane increased by a factor of 3–5. The crystallites were preferentially oriented in the substrate plane as well. The thermoelectric-power parameter of Bi_0.5Sb_1.5Te₃ films after their heat treatment in an inert environment increased approximately twofold to values close to that of the corresponding single crystals.     

Thermoelectric Properties of Mo<Subscript>3</Subscript>Sb<Subscript>5.4</Subscript>Te<Subscript>1.6</Subscript> and Ni<Subscript>0.06</Subscript>Mo<Subscript>3</Subscript>Sb<Subscript>5.4</Subscript>Te<Subscript>1.6</Subscript>

Mo₃Sb₇, crystallizing in the Ir₃Ge₇ type structure, has poor thermoelectric (TE) properties due to its metallic behavior. However, by a partial Sb-Te exchange, it becomes semiconducting without noticeable structure changes and so achieves a significant enhancement in the thermopower with the composition of Mo₃Sb₅Te₂. Meanwhile, large cubic voids in the Mo₃Sb₅Te₂ crystal structure provide the possibility of filling the voids with small cations to decrease the thermal conductivity by the so-called rattling effect. As part of the effort to verify this idea, we report herein the growth as well as measurements of the thermal and electrical transport properties of Mo₃Sb_5.4Te_1.6 and Ni_0.06Mo₃Sb_5.4Te_1.6.