Sintering of Si3N4 with the Addition of Rare-Earth Oxides

The effect of rare-earth oxide additives on the densification of silicon nitride by pressureless sintering at 1600° to 1700°C and by gas pressure sintering under 10 MPa of N₂ at 1800° to 2000°C was studied. When a single-component oxide, such as CeO₂, Nd₂O₃, La₂O₃, Sm₂O₃, or Y₂O₃, was used as an additive, the sintering temperature required to reach approximate theoretical density became higher as the melting temperature of the oxide increased. When a mixed oxide additive, such as Y₂O₃–Ln₂O₃ (Ln=Ce, Nd, La, Sm), was used, higher densification was achieved below 2000°C because of a lower liquid formation temperature. The sinterability of silicon nitride ceramics with the addition of rare-earth oxides is discussed in relation to the additive compositions.     

Improvement of Mechanical Properties and Corrosion Resistance of Porous β-SiAlON Ceramics by Low Y2O3 Additions

Addition of Y₂O₃ as a sintering additive to porous β-SiAlON (Si_{6− z} Al _z O _z N_{8− z} , z = 0.5) ceramics has been investigated for improved mechanical properties. Porous SiAlON ceramics with 0.05–0.15 wt% (500–1500 wppm) Y₂O₃ were fabricated by pressureless sintering at temperatures of 1700°, 1800°, and 1850°C. The densification, microstructure, and mechanical properties were compared with those of Y₂O₃-free ceramics of the same chemical composition. Although this level of Y₂O₃ addition did not change the phase formation and grain size, the grain bonding appeared to be promoted, and the densification to be enhanced. There was a significant increase in the flexural strength of the SiAlON ceramics relative to the Y₂O₃-free counterpart. After exposure in 1 M hydrochloric acid solution at 70°C for 120 h, no remarkable weight loss and degradation of the mechanical properties (flexural and compression strength) was observed, which was attributed to the limited grain boundary phase, and with the minor Y₂O₃ addition the supposed formation of Y-α-SiAlON.     

Subsolidus Phase Equilibria and Ordering in the System ZrO2-Y2O3

The subsolidus phase relations in the entire system ZrO₂-Y₂O₃ were established using DTA, expansion measurements, and room- and high-temperature X-ray diffraction. Three eutectoid reactions were found in the system: ( a ) tetragonal zirconia solid solution→monoclinic zirconia solid solution+cubic zirconia solid solution at 4.5 mol% Y₂O₃ and ∼490°C, ( b ) cubic zirconia solid solutiow→δ-phase Y₄Zr₃O₁₂+hexagonalphase Y₆ZrO₁₁ at 45 mol% Y₂O₃ and ∼1325°±25°C, and ( c ) yttria C -type solid solution→wcubic zirconia solid solution+ hexagonal phase Y₆ZrO₁₁ at ∼72 mol% Y₂O₃ and 1650°±50°C. Two ordered phases were also found in the system, one at 40 mol% Y₂O₃ with ideal formula Y₄Zr₃O₁₂, and another, a new hexagonal phase, at 75 mol% Y₂O₃ with formula Y₆ZrO₁₁. They decompose at 1375° and >1750°C into cubic zirconia solid solution and yttria C -type solid solution, respectively. The extent of the cubic zirconia and yttria C -type solid solution fields was also redetermined. By incorporating the known tetragonal-cubic zirconia transition temperature and the liquidus temperatures in the system, a new tentative phase diagram is given for the system ZrO₂-Y₂O₃.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Microstructure and Short-Term Oxidation of Hot-Pressed Si3N4/ZrO2(+Y2O3) Ceramics

Composite ceramic materials based on Si₃N₄ and ZrO₂ stabilized by 3 mol% Y₂O₃ have been formed using aluminum isopropoxide as a precursor for the Al₂O₃ sintering aid. Densification was carred out by hot-pressing at temperatures in the range 1650° to 1800°C, and the resulting micro-structures were related to mechanical properties as well as to oxidation behavior at 1200°C. Densification at the higher temperatures resulted in a fibrous morphology of the Si₃N₄ matrix with consequent high room-temperature toughness and strength. Decomposition of the ZrO₂ grains below the oxidized surface during oxidation introduced radial stresses in the subscalar region, and from the oxidation experiments it is suggested that the ZrO₂ incorporated some N during densification.     

Phase Relations in the System Fe2O3–Fe3O4–YFeO3 in Air

Measurements were made of temperature and ternary composition for coexisting liquid and crystalline phases on the air isobar in the system Fe₂O₃-Fe₃O₄-YFeO₃ with particular regard to the stability range and compositional limits of yttrium iron garnet. Phase equilibrium relations were determined by conventional quenching techniques combined with measurements of loss in weight at the reaction temperature to locate true ternary compositions. The intersection of the air isobar with the ternary univariant boundary curve for coexisting magnetite, garnet, and liquid phases results in a eutectic-type situation at the composition Y_0.27Fe_1.73 O_2.87 and 1469°± 2°C. A similar intersection of the isobar with the boundary curve for coexisting garnet, orthoferrite, and liquid phases gives rise to a peritectic-type reaction at 1555° 3°C. and Y_0.44Fe_1.56 O_2.89 The yttrium iron garnet crystallizing from liquids within these temperature and composition limits contains up to 0.5 mole % iron oxide in excess of the stoichiometric formula in terms of the starting composition 37.5 mole % Y₂O₃, 62.5 mole % Fe₂O₃. At 1470° C. the garnet phase in equilibrium with oxide liquid contains 2 mole % FeO in solid solution. The small solubility of excess of iron oxide and partial reduction of the garnet phase in air are unavoidable during equilibrium growth from the melt.     

Thermal Expansion and Athermal Phase Transition of Y4AI2O9 Ceramics

Thermal expansion of Y₄A1₄O₉ ceramics prepared at 1600° and 1800°C was measured from room temperature to 1500°C in air. Volume changes at the phase transition of Y₄A1₂O₉, along with thermal hysteresis, were observed around 1400°C. The volume of the high-temperature phase was about 0.5% lower than that of the low-temperature phase. The hysteresis width for the sample prepared at 1600°C was 56°C, wider than that (14°C) for the sample prepared at 1800°C. The averages of phase transition start temperatures on heating and on cooling for these samples were, however, almost the same at 1377°C. The phase transitions did not occur at fixed temperatures, and the proportions of the high-temperature phase and the low-temperature phase did not change with time as long as the temperature remained constant ( athermal character). The sample prepared at 1800°C also showed another thermal hysteresis behavior from room temperature to about 1000°C.     

High-Temperature Phase Relations in the System Y2O3-Ta2O5

The phase relations for the system y₂o₃–Ta₂o₅ in the composition range 50 to 100 mol% Y₂O₃ have been studied by solid-state reactions at 1350°, 1500°, or 17000C and by thermal analyses up to the melting temperatures. Weberite-type orthorhombic phases (W2 phase, space group C222₁), fluorite-type cubic phases (F phase, space group Fm3m )and another orthorhombic phase (O phase, space group Cmmm )are found in the system. The W2 phase forms in 75 mol% Y₂O₃ under 17000C and O phase in 70 mol% Y₂O₃ up to 1700°C These phases seem to melt incongruently. The F phase forms in about 80 mol% Y₂O₃ and melts congruently at 2454° 3°C. Two eutectic points seem to exist at about 2220°C 90 mol% Y²O₃, and at about 1990°C, 62 mol% Y₂O₃. A Phase diagram including the above three phases were not identified with each other.     

Phase Relations Applicable to the Garnet Phase Y3Fe4AlO12

Phase relations of the system Fe₂O₃-Y₂O₃-Al₂O₃ were studied at 1500° and 1525°C in air and in oxygen at 1 atm. Isothermal-isobaric sections indicate that the liquids phase field at 1500°C is larger in oxygen than in air. In either atmosphere, at this temperature, the composition of the garnet phase in equilibrium with a liquid is enriched in aluminum relative to the liquid. In the same manner, yttrium orthoferrite is enriched in aluminum relative to garnet in equilibrium between these two phases. The limit of solid solubility of excess iron-aluminum and/or yttrium in the garnet phase Y₃Fe₄AlO₁₂ was determined by X-ray diffraction techniques to be 0.2 ± 0.05 mole % Y₂.O_3.     

Sintering, Microstructure, Hardness, and Fracture Toughness Behavior of Y2O3-CeO2-ZrO2

A wet-chemical approach is applied to derive fine powders with compositions 11 mol% CeO₂-ZrO₂, 1 mol% YO_1.5-10 mol% CeO₂-ZrO₂, 12 mol% CeO₂-ZrO₂, and 2 mol% YO_1.5-10 mol% CeO₂-ZrO₂ by the coprecipitation method. The characteristics of the as-derived powders are evaluated through thermal analysis and electron microscopy. The sintering behavior of the calcined powders is carried out at 1400° and 1500°C for 1 to 10 h. Sintered density higher than 98% of theoretical is achieved for sintering at 1400°C for several hours. The as-sintered density dependence on the sintering condition is related to the extent of tetragonal-to-monoclinic phase transformation as well as the associated microcracks. Partial substitution by Y₂O₃ in CeO₂-ZrO₂ results in reduced grain size and tends to stabilize the tetragonal structure. Y₂O₃ is more effective than CeO₂ with respect to the grain size refinement and tetragonal stability. In addition, Y₂O₃ substitution in CeO₂-ZrO₂ increases the hardness, while it decreases the fracture toughness.     

Densification of Si3N4 with LiYO2 Additive

This paper deals with the densification and phase transformation during pressureless sintering of Si₃N₄ with LiYO₂ as the sintering additive. The dilatometric shrinkage data show that the first Li₂O- rich liquid forms as low as 1250°C, resulting in a significant reduction of sintering temperature. On sintering at 1500°C the bulk density increases to more than 90% of the theoretical density with only minor phase transformation from α-Si₃N₄ to β-Si₃N₄ taking place. At 1600°C the secondary phase has been completely converted into a glassy phase and total conversion of α-Si₃N₄ to β-Si₃N₄ takes place. The grain growth is anisotropic, leading to a microstructure which has potential for enhanced fracture toughness. Li₂O evaporates during sintering. Thus, the liquid phase is transient and the final material might have promising mechanical properties as well as promising high-temperature properties despite the low sintering temperature. The results show that the Li₂O−Y₂O₃ system can provide very effective low-temperature sintering additives for silicon nitride.     

Phase Equilibria and Ordering in the System ZrO2-Y2O3

The phase diagram for the system ZrO₂-Y₂O₃ was redetermined. The extent of the fluorite-type ZrO₂-Y_zO₃ solid solution field was determined with a high-temperature X-ray furnace, precise lattice parameter measurements, and a hydrothermal technique. Long range ordering occurred at 40 mol% Y₂O₃ and the corresponding ordered phase was Zr₃Y₄OL₁₂. The compound has rhombohedra1 symmetry (space group R 3), is isostructural with UY₆O_l2 and decomposes above 1250±50°C. The results indicate that the eutectoid may occur at a temperature <400°C at a composition between 20 and 30 mol% Y₂O₃ Determination of the liquidus line indicated a eutectic at 83± 1 mol% Y₂O₃ and a peritectic at 76 ± 1 mol% Y₂O₃.     

Densification and Thermal Conductivity of AIN Doped with Y2O3, CaO, and Li2O

Small amounts of Li₂O result in sintering in the AIN-Y₂O₃-CaO and AIN-CaO systems at firing temperatures <1600°C. The effect is ascribed to reduction of the liquidus temperature. Furthermore, Li₂O is removed by volatization at temperatures from 1300° to 1600°C, and its content decreases several ppm from the initial 0.3 wt%. Li₂O-doped AIN specimens containing Y₂O₃ and CaO additives are well densified by firing at 1600°C for 6 h, and their thermal conductivity is 135 W^.m^−1.K⁻¹.The effect of Li₂O addition on sintering and thermal conductivity also is discussed through thermo-dynamic considerations.     

Phase Transition of Rare-Earth Aluminates (RE4Al2O9) and Rare-Earth Gallates (RE4Ga2O9)

Lattice parameters of RE₄Al₂O₉ (RE = Y, Sin, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Yb) prepared at 1600–1800°C and those of RE₄Ga₂O₉ (RE = La, Pr, Nd, Sm, Eu, and Gd) prepared at 1400–1600°C were refined by Rietveld analysis for the X-ray powder diffraction patterns. The parameters increased linearly with the ionic radius of the trivalent rare-earth elements ( r _RE). High-temperature differential calorimetry and dilatometry revealed that both RE₄Al₂O, and RE₄Ga₂O, have reversible phase transitions with volume shrinkages of 0.5–0.7% on heating and thermal hystereses. The transition temperatures (7_tr) decreased from 1300°C (Yb) to 1044°C (Sm) for RE₄A1₂O₉, except for Y₄Al₂O₉ ( T_tr = 1377°C), and from 1417°C (Gd) to 1271°C (La) for RE₄Ga₂O, with increasing ionic radius of the rare-earth elements. These transition temperatures were plotted on a curve against the ionic radius ratio of Al³⁺ or Gd³⁺ and RE³⁺ ( r _A1Ga/r_RE) except for Y₄Al₂O₉.     

Sintering of Silicon Nitride with YAIO3 Additive

Sintering of Si₃N₄ powder with the addition of a Y₂O₃+ Al₂O₃ mixture or YAlO₃ as sintering aids was investigated. Sintering was improved in the case of YAlO₃ additive compared to that for the Y₂O₃+ Al₂O₃ mixture. An initial delay in densification was most likely caused by heterogeneity of the liquid phase formed in the case of the separate oxide additions at temperatures above 1700°C.     

Activated Sintering of ThO2 and ThO2-Y2O3 with NiO

The effect of additives on the sintering of ThO₂ and ThO₂-Y₂O₃ compacts and loose powders was studied by isothermal shrinkage measurements and by scanning electron micrography. Small amounts of the oxides of Ni, Zn, Co, and Cu reduced the sintering temperature. The behavior of NiO at a concentration of 0.8 wt% (2.5 mol%) was studied in detail and found to yield high-density bodies at temperatures below 1500°C. The presence of Y₂O₃ as a separate phase increases the rate of sintering of ThO₂, but smaller amounts of NiO are much more potent. The major portion of the densification occurs very rapidly and is followed by a much slower sintering process typical of volume diffusion. The fast early shrinkage may be caused by the capillary forces of a liquid, but since no evidence of melting was found, a solid-state mechanism may be responsible.     

Solid-Liquid Reaction in the Si3N4-AlN-Y2O3 System under 1 MPa of Nitrogen

The melting behaviors of selected compositions in the Si₃N₄-AlN-Y₂O₃ system were determined under 1 MPa of nitrogen. The phase diagrams of the ternary and their binary systems are presented. The lowest melting composition of the ternary system contains 15 mol % Si₃N₄, 25 mol % AIN, and 60 mol % Y₂O₃ and has a melting temperature of 1650°C. The binary eutectic compositions and temperatures are 15 mol % Si₃N₄ and 85 mol % Y₂O₃ at 1720°C, and 20 mol % AIN and 80 mol% Y₂O₃ at 1730°C.     

The System Si3N4-SiO2-Y2O3

Subsolidus phase relations were established in the system Si₃N₄-SiO₂-Y₂O₃. Four ternary compounds were confirmed, with compositions of Y₄Si₂O₇N₂, Y₂Si₃O₃N₄, YSiO₂N, and Y₁₀(SiO₄)₆N₂. The eutectic in the triangle Si₃N₄-Y₂Si₂O₇-Y₁₀(SiO₄)₆N₂ melts at 1500°C and that in the triangle Si₂N₂O-SiO₂-Y₂Si₂O₇ at 1550°C. The eutectic temperature of the Si₃N₄-Y₂Si₂O₇ join was ∼ 1520°C.     

Characterization of Photoluminescent (Y1–xEux)2O3 Thin Films Prepared by Metallorganic Chemical Vapor Deposition

The purpose of this study was to identify and correlate the microstructural and luminescence properties of europium-doped Y₂O₃ (Y_{1– x} Eu _x )₂O₃ thin films deposited by metallorganic chemical vapor deposition (MOCVD), as a function of deposition time and temperature. The influence of deposition parameters on the crystallite size and microstructural morphology were examined, as well as the influence of these parameters on the photoluminescence emission spectra. (Y_{1– x} Eu _x )₂O₃ thin films were deposited onto (111) silicon and (001) sapphire substrates by MOCVD. The films were grown by reacting yttrium and europium tris(2,2,6,6-tetramethyl–3,5-heptanedionate) precursors with an oxygen atmosphere at low pressures (5 torr (1.7 × 10³ Pa)) and low substrate temperatures (500°–700°C). The films deposited at 500°C were smooth and composed of nanocrystalline regions of cubic Y₂O₃, grown in a textured [100] or [110] orientation to the substrate surface. Films deposited at 600°C developed, with increasing deposition time, from a flat, nanocrystalline morphology into a platelike growth morphology with [111] orientation. Monoclinic (Y_{1– x} Eu _x )₂O₃ was observed in the photoluminescence emission spectra for all deposition temperatures. The increase in photoluminescence emission intensity with increasing postdeposition annealing temperature was attributed to the surface/grain boundary area-reduction effect.     

Phase Relations in the System ZrO2-Y2O3 at Low Y2O3 Contents

Subsolidus phase relations in the low-Y₂O₃ portion of the system ZrO_2-Y₂O₃ were studied using DTA with fired samples and X-ray phase identification and lattice parameter techniques with quenched samples. Approximately 1.5% Y₂O₃ is soluble in monoclinic ZrO₂, a two-phase monoclinic solid solution plus cubic solid solution region exists to ∼7.5% Y₂O₃ below ∼500°C, and a two-phase tetragonal solid solution plus cubic solid solution exists from ∼1.5 to 7.5% Y₂O₃ from ∼500° to ∼1600°C. At higher Y₂O₃ compositions, cubic ZrO₂ solid solution occurs.