Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

Processing and Piezoelectric Properties of (Na0.5K0.5)0.96Li0.04(Ta0.1Nb0.9)1−xCuxO3−3x/2 Lead-Free Ceramics

The Cu-modified (Na_0.5K_0.5)_0.96Li_0.04Ta_0.1Nb_0.9O₃ lead-free piezoelectric ceramics were fabricated at relatively low temperatures by ordinary sintering. The results indicate that the addition of copper oxide (CuO) does not change the crystal structure and the dielectric–temperature characteristic, but tends to slightly increase the loss tangent and significantly modify the ferroelectric and electromechanical properties. Moreover, the grains get clearly coarsened with increasing CuO content. When doped with <0.25% CuO, the materials get softer with slightly decreased coercive fields ( E _c) and increased maximum electric field-driven strains ( S _m), and thus own enhanced piezoelectric properties; however, as the doping level becomes higher, the materials get harder, possessing larger E _c and reduced remanent polarization and S _m. The change in the electrical properties can be attributed to both the formation of oxygen vacancies by Cu²⁺ replacing Nb⁵⁺ and the modification of densification.     

Improved Microwave Dielectric Properties of Ba6Ti1−xSnxNb4O18 Ceramics

Single-phase polycrystalline microwave dielectric ceramics Ba₆Ti_{1− x} Sn _x Nb₄O₁₈, with x changing from 0 to 1, were synthesized by the solid-state reaction method. All the solid solutions fitted well with A₆B₅O₁₈ cation-deficient hexagonal perovskite structure. The substitution of Sn for Ti effectively enhanced the quality factor and controlled τ_f. With increasing Sn content, the dielectric constant decreased from ∼47 to ∼32, and the Q × f value increased significantly from 11 530 to 28 496 GHz, with τ_f varying from 64 to 0 ppm/°C. A zero τ_f was realized when Sn was fully replaced by Ti with the composition Ba₆SnNb₄O₁₈.     

Microstructure and Piezoelectric Properties of (1−x)(Na0.5K0.5)NbO3–xLiNbO3 Ceramics

(1− x )(Na_0.5K_0.5)NbO₃– x LiNbO₃ [(1− x )NKN– x LN] ceramics were produced by the conventional solid-state sintering method, and their microstructure and piezoelectric properties were investigated. The formation of the liquid phase and K₆Li₄Nb₁₀O₃₀ second phase that were observed in the (1− x )NKN– x LN ceramics was explained by the evaporation of Na₂O during the sintering. A morphotropic phase boundary (MPB) was observed in the specimens with 0.05< x <0.08. Promising piezoelectric properties were obtained for the specimens with x =0.07. Therefore, the piezoelectric properties of this 0.93NKN–0.07LN ceramic were further investigated and were found to be influenced by their relative density and grain size. In particular, grain size considerably affected the d ₃₃ value. Two-step sintering was conducted at different temperatures to increase the grain size. Piezoelectric properties of d ₃₃=240 (pC/N) and k _p=0.35 were obtained for the 0.93NKN–0.07LN ceramics sintered at 1030°C and subsequently annealed at 1050°C.     

Piezoelectric Properties of (1−x)(Na0.5K0.5)NbO3–xAgSbO3 Lead-Free Ceramics

(1− x )(Na_0.5K_0.5)NbO₃– x AgSbO₃ lead-free piezoelectric ceramics were prepared by normal sintering. The effects of the AgSbO₃ on the phase structure and piezoelectric properties of the ceramics were systematically studied. These results show that the AgSbO₃-modified (K_0.50Na_0.50)NbO₃ lead-free piezoelectric ceramics form stable solution with orthorhombic structure, and the Curie temperature and the polymorphic phase transition of the ceramics decreased with increasing AgSbO₃. The result shows that the piezoelectric properties of the ceramics strongly depend on the AgSbO₃. The ceramics with x =0.05 possess optimum properties ( d ₃₃=192 pC/N, k _p=43%, T _c=348°C, T _o−t =145°C, ɛ_r∼632, and tan δ∼3.5%). These results indicate that the ceramic is a promising candidate material for lead-free piezoelectric ceramics.     

Phase Transitions and Electrical Properties of (Na1−xKx)(Nb1−ySby)O3 Lead-Free Piezoelectric Ceramics With a MnO2 Sintering Aid

Lead-free piezoelectric ceramics (Na_{1− x} K _x )(Nb_{1− y} Sb _y )O₃+ z mol% MnO₂ have been prepared by a conventional solid-state sintering technique. Our results reveal that Sb⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with a single-phase orthorhombic perovskite structure. The partial substitution of Sb⁵⁺ for B-site ion Nb⁵⁺ decreases the paraelectric cubic-ferroelectric tetragonal phase transition ( T _c) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition ( T _O–F), and retains strong ferroelectricity. A small amount of MnO₂ is enough to improve the densification of the ceramics. The co-effects of MnO₂ doping and Sb substitution lead to significant improvements in ferroelectric and piezoelectric properties. The ceramics with x =0.45–0.525, y =0.06–0.08, and z =0.5–1 exhibit excellent ferroelectric and piezoelectric properties: d ₃₃=163–204 pC/N, k _P=0.47–0.51, k _t=0.46–0.52, ɛ=640–1053, tan δ=1.3–3.0%, P _r=18.1–22.6 μC/cm², E _c=0.72–0.98 kV/mm, and T _C=269°–314°C.     

Ferroelectric and Piezoelectric Properties of Fine-Grained Na0.5K0.5NbO3 Lead-Free Piezoelectric Ceramics Prepared by Spark Plasma Sintering

Lead-free piezoelectric ceramics have received attention because of increasing interest in environmental protection. Niobate ceramics such as NaNbO₃ and KNbO₃ have been studied as promising Pb-free piezoelectric ceramics, but their sintering densification is fairly difficult. In the present study, highly dense Na_0.5K_0.5NbO₃ ceramics were prepared using spark plasma sintering (SPS). Although the SPS temperature was as low as 920°C, the density of the Na_0.5K_0.5NbO₃ solid solution ceramics was raised to 4.47 g/cm³ (>99% of the theoretical density). After post-annealing in air, reasonably good ferroelectric and piezoelectric properties were obtained in the Na_0.5K_0.5NbO₃ ceramics with submicron grains. The crystal phase of the Na_0.5K_0.5NbO₃ has an orthorhombic structure. The Curie temperature is 395°C and the piezoelectric parameter ( d ₃₃) of the Na_0.5K_0.5NbO₃ ceramics reached 148 pC/N.     

Ferroelectric and Ferromagnetic Properties of Hot-Pressed Bi0.95−xLa0.05TbxFeO3 Ceramics

Multiferroic Bi_{0.95− x} La_0.05Tb _x FeO₃ (BLTFO) ceramics were prepared by hot-pressing. It was found that their dielectric properties were very sensitive to sintering temperature. The samples hot-pressed at 740°C show stable dielectric constant and rather low loss (∼1%) in the frequency range up to 1 MHz. When the nominal content of Tb is <0.08, the atomic arrangement keeps the R 3 c symmetry, while a phase transition appears at x ≈0.08–0.10. The introduction of Tb enhances the coercive field of the BLTFO ceramics and then restrains the ferroelectricity gradually. The doping of Tb at x ≤0.10 increases the ferromagnetization.     

Methane Oxidation on Perovskite-Type Ca(Mn1−xTix)O3−δ

X-ray photoelectron spectroscopy was performed to elucidate the catalytic activity of CH₄ oxidation on perovskite-type Ca(Mn_{1− x} Ti _x )O_3−δ synthesized at 1173 K in a flow of oxygen from a gel with citric acid and ethylene glycol. The Mn ion content decreases and the ratio of the Mn³⁺ ion in the Mn ion increases with increases in x . Ca(Mn_{1− x} Ti _x )O_3−δ has a high catalytic activity of CH₄ oxidation at x =0.4. These results indicate that the catalytic activity strongly depends on the Mn³⁺ ion content of the surface.     

Preparation, Structure, and Dielectric Properties of the System Ba1−xLaxTi1−xNixO3

Attempts have been made to synthesize the compositions with x = 0.01, 0.05, 0.10, 0.20, 0.30, 0.40, and 0.50 in the valence-compensated solid-solution Ba_1–xLa_xTi_1–xNi_xO₃ by ceramic methods. Solid solutions formed in the compositions with x0.10. The structure of the composition with x = 0.01 is tetragonal, whereas samples with x = 0.05 and 0.10 are cubic. A ferroelectric-paraelectric transition is observed only in the composition with x = 0.01 at ∼ 350 K.     

Microstructure of KTaxNb1−xO3 Thin Films on MgO (100) Single Crystals

Thin KTa_xNb_1−xO₃ (KTN) films were prepared by deposition of sol–gel precursor solutions on MgO (100) single crystals. Crystal structure and microstructure of the films as a function of processing parameters, such as rate, duration, and temperature of postdeposition heat treatment, were studied. Several techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were employed to analyze the films. It was observed that slow heating of KTN films promotes pyrochlore formation while fast-firing of the films results in predominant formation of the perovskioe phase. In slow-heated samples, TEM showed randomly oriented pyrochlore crystallites with a vermicular nanostructure of 10–30 nm with an interpenetrating porosity of the same range. In fast-fired samples, large perovskite pockets with pyrochlore crystallites scattered among them were seen. The large perovskite grains were on the order of 0.1–0.5 μm, irregular in shape and porous. Transmission electron diffraction indicated these were single crystals, and ferroelectric domains were observed in them. Films of up to 1 μm thick were obtained by multiple deposition of the sol–gel KTN. Dense films were achieved when each layer was densified at 750°C for 2 h before the next layer was deposited.     

Electrical Conduction Behavior of La1+xSr1−xGa3O7–δ Melilite-Type Ceramics

Ceramics of the melilite-type compound La_{1+ x} Sr_{1− x} Ga₃O_7−δ were prepared by conventional ceramic processing. Samples prepared represented the entire homogeneity region of the phase (i.e., x =−0.15 to 0.60). Electrochemical characterization under variable temperature and atmospheric conditions in the vicinity of air entailed four-point direct-current conductivity measurements and electromotive force measurements. La_{1+ x} Sr_{1− x} Ga₃O_7−δ samples exhibited a p -type behavior with generally increased conductivity with increased substitution of lanthanum for strontium, which reached a saturation value of ∼10⁻¹ S·cm⁻¹ at 950°C.     

A Phase Diagram for Epitaxial PbZr1−xTixO3 Thin Films at the Bulk Morphotropic Boundary Composition

A phase diagram of temperature versus strain was constructed for a (001)-oriented PbZr_{1− x} Ti _x O₃ epitaxial single crystal thin film near the bulk morphotropic boundary composition ( x =0.47) on an (001)-oriented cubic substrate. The phase-field approach is employed. It is shown that a mixture of distorted rhombohedral, orthorhombic, and tetragonal phases exists under small values of strain, i.e., close to the in-plane clamped boundary condition. This result contradicts thermodynamic calculations assuming a single-domain state that predicted a single distorted rhombohedral phase under similar strains. Furthermore, it is demonstrated that under a large tensile strain current phase-field simulations showed a tetragonal phase with a ₁ /a ₂ twin structures as the stable state whereas thermodynamic calculations predicted an orthorhombic phase.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Low-Temperature Sintering and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

(Na_0.5K_0.5)NbO₃ (NKN) ceramic with 1.5 mol% CuO added (NKNC) was well sintered even at a low temperature of 900°C with the addition of ZnO. Most of the ZnO reacted with the CuO and formed the liquid phase that assisted the densification of the specimens at 900°C. A few Zn²⁺ ions entered the matrix of the specimens and increased the coercive field ( E _c) and Q _m values of the specimens. High-piezoelectric properties of k _p=0.37, Q _m=755, and ɛ₃ ^T /ɛ₀=327 were obtained from the NKNC ceramics containing 1.0 mol% ZnO sintered at 900°C for 2 h.     

Phase Transition and Ferroelectric Characteristics of Pb[(Mg1/3Nb2/3)1-xTix]O3 Ceramics Modified with La(Mg2/3Nb1/3)O3

The effects of 0–5 mol% addition of La(Mg_2/3Nb_1/3)O₃ (LMN) on the phase transition and ferroelectric behaviors of Pb[(Mg_1/3Nb_2/3)_1-xTi_x]O₃ (PMNT) ceramics with compositions near the morphotropic phase boundary (MPB) were studied. An evolution of structure from rhombohedral to tetragonal was found with increasing PbTiO₃ (PT) content across the MPB (at ∼32.5 mol% PT), and a coexistence of both rhombohedral and tetragonal phases was also found at the MPB. The dual-phase field extended toward the lower PT content side of the MPB, and, moreover, the rhombohedrality or tetragonality was reduced, especially for the compositions near the MPB, by the addition of La in PMNT. The ferroelectric transition was found to change from normal to diffuse as the La content increased and the compositions became more rhombohedral. In accordance with the structural evolution, the change of remanent polarization ( P _r) and coercive field ( E _c) also became gradually indistinct, and both P _r and E _c were reduced. For compositions near the MPB, both PMNT and La-modified PMNT had a similar electromechanical factor ( k _p) in a range around 0.55–0.60, but the mechanical quality factor ( Q _m) was significantly reduced for the La-modified PMNT. The piezoelectric coefficient ( d ₃₃), however, was largely improved with increasing La content in PMNT of compositions at MPB. A high value of d ₃₃∼ 815 pC/N was obtained for the 5-mol%-La-modified ceramics, but it was associated with a low value of Q _m.     

High Piezoelectric and Dielectric Properties of La-Doped 0.3Pb(Zn1/3Nb2/3)O3–0.7Pb(ZrxTi1−x)O3 Ceramics Near Morphotropic Phase Boundary

La-doped 0.3Pb(Zn_1/3Nb_2/3)O₃–0.7Pb(Zr _x Ti_{1− x} )O₃ ( x =0.5–0.53) piezoelectric ceramics with pure perovskite phase were synthesized by a two-step hot-pressing route. The piezoelectric properties of various compositions near the morphotropic phase boundary (MPB) were systematically investigated. Not only was the exact MPB of this system determined via X-ray diffractometry analysis, but also the peak of piezoelectric properties was found near the MPB. The optimum piezoelectric properties of this series were observed in the specimen with Zr/Ti=51/49. The piezoelectric coefficient ( d ₃₃) and electromechanical coupling factor ( k _p) were 845 pC/N and 0.70, respectively, which have not been reported in this system so far. Large permittivity (ɛ_r=4088) and permittivity maximum (ɛ_m=29 500) were also obtained for the poled specimens. The temperatures ( T _max) of the permittivity maxima ranged from 206° to 213°C with various Zr/Ti ratios.     

Defect Structure and Electrical Properties of La1−ySryFe1−xAlxO3−δ

La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites were studied as potential materials for solid-oxide fuel cell (SOFC) cathodes. The phase relations in the LaFeO₃–SrFeO_3−δ–LaAlO₃ system were investigated by X-ray powder diffraction analysis. The defect structure of the La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites was investigated by Mössbauer spectroscopy and weight-loss analysis. Relations between the nonstoichiometry and the conductivity of the La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ perovskites were investigated. The incorporation of aluminum ( x ) into LaFe_{1− x} Al_xO₃ was found to have no influence on the defect structure but to decrease the conductivity. The incorporation of strontium ( y ) into La_{1− y} Sr _y Fe_{1− x} Al _x O_3−δ promotes the formation of anion vacancies and Fe⁴⁺ that lead to higher conductivity.     

Structure and Microwave Dielectric Properties of (Zn1−xCox)TiO3 Ceramics

Dielectric ceramics in the system (Zn_{1− x} Co _x )TiO₃ ( x = 0–1) were synthesized by the solid-state reaction route. The phase distribution, microstructure, and dielectric properties were characterized by using powder X-ray diffraction analysis, electron microscopy, and microwave measurement techniques. Three phase composition regions were identified in the specimens sintered at 1150°C; [spinel + rutile] at 0 ≤ x ≤ 0.5, [spinel + ilmenite + rutile] at 0.5 < x ≤ 0.7, and [ilmenite] phase at 0.7 < x ≤ 1. For the 0 ≤ x ≤ 0.5 region, the amount of Ti-rich precipitates incorporated into the spinel phase decreased with the Co content at 0 ≤ x ≤ 0.5, with a concomitant increase of the rutile phase. The ilmenite phase appeared for high Co content. The microwave dielectric properties depended on the phase composition and volume according to the three phase regions, where the relative amount of rutile to the spinel or ilmenite determined the dielectric properties. The dielectric constant as a function of Co addition was modeled with a Maxwell mixing rule. An optimum phase distribution was determined in this system with dielectric constant of 25, a Q * f 70 000 GHz, and a low temperature coefficient of the resonant frequency.     

Compositional Dependence of Piezoelectric Properties in NaxK1−xNbO3 Lead-Free Ceramics Prepared by Spark Plasma Sintering

Lead-free piezoelectric Na _x K_{1− x} NbO₃ ( x =20–80 mol%) ceramics were fabricated using spark plasma sintering at a low temperature (920°C). All the Na _x K_{1− x} NbO₃ ceramics showed a similar orthorhombic phase structure, while the corresponding lattice parameters decreased from the KNbO₃ side to the NaNbO₃ side with increasing Na content. A discontinuous change in lattice parameter close to composition of 60 mol% Na indicated the presence of a transitional area that is similar to the morphotropic phase boundary (MPB) in Na _x K_{1− x} NbO₃ ceramics. The sintered density of the Na _x K_{1− x} NbO₃ ceramics decreased with increasing Na content, from a relative density of 99% for the K-rich side to 92% for the Na-rich side. The piezoelectric constant d ₃₃ and planar mode electromechanical coupling coefficient k _p showed a maximum value of 148 pC/N and 38.9%, respectively, due to the similar MPB effects in the PZT system.