一种紧凑型超宽带双陷波天线设计与研究

超宽带(UWB)系统的工作频段与现有的许多窄带系统频段相互重叠,因此各个系统信号之间存在潜在的干扰。针对上述问题提出了一种紧凑型超宽带双陷波天线。天线由一个圆形辐射贴片构成并通过50W的微带线进行馈电。接地板和传统的接地板相比被截短了,以提高天线的阻抗带宽。通过在辐射贴片上刻蚀H 型槽来实现天线的双陷波功能,并在微带馈线中引入了嵌入式谐振回路(ERC)结构,加大了天线的陷波深度和阻带宽度,陷波性能好于同频段的双陷波天线。仿真和测试结果表明,天线在3.1～4.2 GHz 以及5.0～6.6GHz 具有陷波特性,有效地避免了WiMAX 和WLAN 频段信号的干扰。同时在2.8 ~10.7 GHz 的其它频段上具有良好的阻抗匹配和较好辐射方向特性。天线的尺寸为34mm*26mm*1.6 mm,结构较为紧凑。     

具有五陷波的超宽带天线设计

设计了一款具有五陷波特性的小型化超宽带天线,通过改变陷波结构参数和分析天线表面的电流分布,研究了陷波结构对超宽带及陷波特性的影响。天线尺寸仅为25 mm×20 mm×1 mm。辐射贴片由矩形和圆形贴片组成,背板通过切角挖槽实现了超宽带特性;添加对称钩型枝节,蚀刻U型槽及3类U型槽产生5个陷波。天线的工作带宽在3.8～16 GHz。有效抑制了国际卫星波段(4.5～4.8 GHz)、WLAN下行波段(5.15～5.35 GHz)、UNII-2c(5.47～5.725 GHz)、WLAN上行波段(5.725～5.825 GHz)、下行卫星系统频段(7.25～7.75 GHz)、上行卫星系统频段(7.9～8.4 GHz)、国际电信联盟频段(8.01～8.50 GHz)的干扰。天线在工作频带内具有全向性,增益平均在4 dBi以上。仿真和实测结果基本吻合,表明该天线可用于超宽带通信系统。     

具有双陷波特性的蜂窝结构分形超宽带天线

提出了一款具有双陷波特性的蜂窝结构分形超宽带（ultra-wideband，UWB）天线，采用二阶蜂窝结构作为辐射贴片和缺陷地结构接地板实现良好的超宽带特性.通过在辐射贴片上挖去正六边形和矩形宽缝隙并引入对称鱼钩形枝节，在馈线处刻蚀倒U形窄缝隙产生了3.27~4.27 GHz和7.2~8 GHz两个频段的陷波特性.天线在2.8~11.6 GHz的频段内，可有效抑制WiMAX、C波段卫星和X波段卫星窄带系统的干扰.仿真和实测结果基本吻合，表明该天线适合应用于各种UWB通信系统.     

一种五陷波超宽带天线的设计

为了在所需的多个陷波频带中获得额外的谐振频率,设计了一种具有五陷波特性的超宽带单极子天线,天线包括蚀刻了两个不封闭口字型槽的秤砣形贴片、矩形微带馈电线、缺陷接地板和两个类U形谐振器.将两个类U形谐振器耦合在馈电线附近,与辐射贴片上蚀刻的两个槽及缺陷接地板共同实现五陷波特性.该天线工作带宽为3.01～12 GHz,有效滤除了WiMAX通信频段(3.73～3.89 GHz)、C频段卫星通信系统(4.25～4.9 GHz)、无线局域网通信频段(5.51～5.83 GHz)、INSAT(Indian National Satellite System)频段(6.77～7.32 GHz)和ITU 8GHz频段(8.13～8.38 GHz)的干扰,且天线在通带频段内五个陷波特性和方向性结果均吻合良好.     

一种具有三阻带特性的超宽带天线的设计与研究*

提出了一种紧凑型共面波导馈电的具有三阻带特性的超宽带天线。所设计天线的基本几何结构由共面波导(CPW)馈电线、菱形辐射贴片和矩形宽缝隙组成。通过在辐射贴片上刻蚀一个U型槽,以及在共面波导的接地面上增加两对L型的寄生旁枝结构来实现天线的三陷波特性。天线尺寸为32mm×32mm×0.508mm。仿真和实验结果表明,该天线在2.6~11.5GHz的频段内电压驻波比小于2,在3.15~3.80GHz、5.20~5.80GHz和8.2~8.7GHz三个频段内具有陷波特性,分别有效阻隔了Wi MAX系统、WLAN系统和ITU 8GHz频段信号对于超宽带(UWB)系统的干扰。在除三个阻带频段外的其余UWB工作频段范围内,具有良好的辐射方向特性和稳定的增益。仿真结果和实验结果表现出良好的一致性。     

一种小型的三陷波UWB天线

设计了一种小型三陷波平面超宽带天线,通过在天线的辐射贴片上加载U形缝隙、在接地板上开一对对称的L形缝隙和引入寄生条带,使得天线在3.2～3.6GHz、3.7～4.3GHz和5.3～6GHz频段内实现频率阻断。利用仿真软件研究了U形缝隙、L形缝隙和寄生条带对陷波特性的影响,并对所设计的超宽带天线进行了制作和测量。结果显示,该天线在工作频段2.8～10.6GHz内具有良好的辐射方向特性,能广泛应用于超宽带系统。     

一种新型具有陷波特性的宽带单极子天线

设计了一款新型的具有陷波特性的超宽带单极子天线。该天线的带宽为3. 1 ~ 12. 0 GHz,通过在矩 形辐射贴片上制作出对称的梯形结构、中心加载倒C 形缝隙、矩形开槽,并将窄矩形接地板切除两个边角,制作矩形 开槽结构,使得天线在3. 3 ~5. 35 GHz 频段产生陷波特性。该天线结构紧凑,尺寸仅为20 mm×25 mm×1. 0 mm。建 立天线模型,并对其进行仿真和优化。研究表明,天线在WiMAX 频段、C 波段、数字微波通信、大容量微波通信和部 分WLAN 等多个频段产生良好的陷波特性,且在工作频段内有良好的性能和辐射方向特性。     

一种共面波导馈电的双陷波渐变槽天线

为了滤除WIMAX(3.3～3.8 GHz)和WLAN(5.125～5.825 GHz)窄带信号对超宽带系统的干扰,该文提出一款共面波导馈电的小型化双陷波渐变槽天线。共面波导结构可以有效地扩展天线的带宽,实现对整个UWB(3.1～10.6 GHz)频段的全覆盖。通过在天线的馈线上开L型缝隙和在辐射贴片上开一对E字型缝隙的方法,有效实现了在3.15～3.97 GHz和4.94～6.05 GHz频段的双陷波特性,能够抑制WIMAX和WLAN对超宽带系统的干扰。该天线结构简单紧凑,尺寸非常小,仅为40 mm×18 mm×0.813 mm。仿真和实测结果表明该天线在超宽带波段内具有良好的陷波特性、增益特性,可以应用于小型化超宽带系统中。文中方法对于陷波渐变槽天线的研究具有一定的借鉴意义。     

具有高隔离度的紧凑型三陷波UWB-MIMO天线设计

提出了一种具有高隔离度的紧凑型三陷波超宽带（ultra-wideband, UWB）多输入多输出（multiple-input multiple-output, MIMO）天线,整体尺寸为38 mm×26 mm×1.2 mm.通过对辐射贴片底部两侧进行多切角,实现了宽带化;通过在接地板上加载改进的波纹T型去耦结构,并刻蚀倒“π”型槽缝隙,实现了较高隔离度;通过在辐射贴片上刻蚀“U”型缝隙、在馈线上刻蚀类“H”型缝隙以及在右侧引入倒“C”型寄生枝节,实现了WiMAX(3.3～3.6 GHz)、WLAN(5.15～5.85 GHz)和X波段（7.25～7.75 GHz）3个频段的陷波.仿真与测试结果表明,该天线工作频段为2.9～11.3 GHz（相对带宽达到118.31%）,隔离度小于-22.6 dB,包络相关系数小于0.01,辐射效率高,辐射特性良好,可以广泛应用于无线通信系统领域中.     

一种双陷波超宽带天线设计与研究

为了避免如WiMax和WLAN等窄带通信系统对超宽带通信系统的影响,该文提出一种具有双陷波特性的超宽带天线。该天线采用圆形贴片作为辐射单元,通过在贴片和接地板上分别开圆弧状的H形槽和L形槽来实现双陷波特性。天线在3.1~10.6 GHz的超宽带频段内能够有效地工作并抑制两种不同的窄带通信系统的干扰。同时圆弧状H形槽的参数研究表明,这种开槽结构能够以槽参数组合的形式更有效地控制陷波中心频率。实测和仿真结果吻合,该天线实现了良好的陷波功能,在工作频段内有良好的辐射方向特性。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks