Compositional and optoelectronic properties of CIS and CIGS thin films formed by electrodeposition

CuInSe₂ (CIS) and Cu(In,Ga)Se₂ (CIGS) thin films were prepared by electrodeposition and processing. The influence of film deposition parameters such as bath composition, pH, deposition potential and material purity on film properties was studied. The structural, morphological, compositional and opto-electronic properties of electrodeposited and selenized CIS and CIGS thin films were characterized using various techniques. As-deposited as well as selenized films exhibited a compact or a granular morphology depending on the composition. The film stoichiometry was improved after selenization at 550°C in a tubular furnace. The films are formed with a mixed phase composition of CuInSe₂ and CuIn₂Se_3.5 ternary phases.     

Fabrication of CuInSe2 films and solar cells by the sequential evaporation of In2Se3 and Cu2Se binary compounds

Cu₂Se/In_xSe(x≈1) double layers were prepared by sequentially evaporating In₂Se₃ and Cu₂Se binary compounds at room temperature on glass or Mo-coated glass substrates and CuInSe₂ films were formed by annealing them in a Se atmosphere at 550°C in the same vacuum chamber. The In_xSe thickness was fixed at 1 μm and the Cu₂Se thickness was varied from 0.2 to 0.5 μm. The CuInSe₂ films were single phase and the compositions were Cu-rich when the Cu₂Se thickness was above 0.35 μm. And then, a thin CuIn₃Se₅ layer was formed on the top of the CuInSe₂ film by co-evaporating In₂Se₃ and Se at 550°C. When the thickness of CuIn₃Se₅ layer was about 150 nm, the CuInSe₂ cell showed the active area efficiency of 5.4% with V_oc=286 mV, J_sc=36 mA/cm² and FF=0.52. As the CuIn₃Se₅ thickness increased further, the efficiency decreased.     

Scanning tunneling microscopy of electrodeposited CuInSe2 nanoscale multilayers

We have investigated the electrochemical deposition of modulated thin films based on the Cu_xIn_2−xSe₂ system. CuInSe₂ is a leading alternative to silicon for use in thin film photovoltaic solar cells due to its optical absorption and electrical characteristics. Alternating layers of two different compositions based on the Cu_xIn_2−xSe₂ system were potentiostatically deposited. These nanometer-scale layers are used to form reduced-dimensionality structures such as superlattices that can be used in concentrator solar cells. We have used X-ray diffraction, energy-dispersive spectroscopy, and scanning tunneling microscopy to characterize our asdeposited thin films. The ability of the scanning tunneling microscope to resolve the individual nanoscale layers of our multilayered thin films is shown and is used to determine modulation wavelengths.     

Thermal diffusion of Cu into In2Se3: A better approach to SEL technique in the deposition of CuInSe2 thin films

This paper reports the modifications made in the preparation techniques of getting CuInSe₂ thin films starting with chemical bath deposited (CBD) selenium films. In the present study, CBD Se film was converted into CuInSe₂ by stacked elemental layer (SEL) technique and also by thermal diffusion of Cu into In₂Se₃. In both the cases CBD Se films were used to avoid toxic Se vapor and H₂Se gas. Improvements were made in these techniques through a detailed study, varying the composition of the films over a wide range by changing the Cu/In ratio. Structural, optical and electrical characterizations were performed. On comparing the material properties of CuInSe₂ deposited by these two techniques, it was found that photosensitivity was better for samples prepared by thermal diffusion of Cu into In₂Se₃. So the technique of thermal diffusion of Cu into In₂Se₃ was found to be better than SEL technique in the preparation of CuInSe₂ using CBD Se. Cu-rich, In-rich and nearly stoichiometric samples could be prepared by thermal diffusion of Cu into In₂Se₃. These samples were analyzed using energy dispersive spectroscopy, Raman spectroscopy and atomic force microscopy also.     

Effect of selenization pressure on CuInSe2 thin films selenized using co-sputtered Cu-In precursors

CuInSe₂ thin films were formed from the selenization of co-sputtered Cu–In alloy layers. These layers consisted of only two phases, CuIn₂ and Cu₁₁In₉, over broad Cu–In composition ratio. The concentration of Cu₁₁In₉ phase increased by varying the composition from In-rich to Cu-rich. The composition of co-sputtered Cu–In alloy layers was linearly dependent on the sputtering power of Cu and In targets. The metallic layers were selenized either at a low pressure of 10 mTorr or at 1 atm Ar. A small number of Cu–Se and In–Se compounds were observed during the early stage of selenization and single-phase CuInSe₂ was more easily formed in vacuum than at 1 atm Ar. Therefore, CuInSe₂ films selenized in vacuum showed smoother surface and denser microstructure than those selenized at 1 atm. The results showed that CuInSe₂ films selenized in vacuum had good properties suitable for a solar cell.     

An investigation into effect of cationic precursor solutions on formation of CuInSe2 thin films by SILAR method

SILAR deposition of CuInSe₂ films was performed by using Cu²⁺–TEAH₃ (cupric chloride and triethanolamine) and In³⁺–CitNa (indium chloride and sodium citrate) chelating solutions with weak basic pH as well as Na₂SeSO₃ solution at 70 °C. A separate mode and a mixed one of cationic precursor solutions were adopted to investigate effects of the immersion programs on crystallization, composition and morphology of the deposited CuInSe₂ films. Chelating chemistry in two solution modes was deducted based on IR measurement. The XRD, XPS and SEM results showed that well-crystallized, smoothly and distinctly particular CuInSe₂ films could be obtained after annealing in Ar at 400 °C for 1 h by using the mixed cationic solution mode.     

Electrodeposition of CuInxGa1−xSe2 thin films

CuIn_xGa_1−xSe₂ (CIGS) polycrystalline thin films with various Ga to In ratios were grown using a new two-step electrodeposition process. This process involves the electrodeposition of a Cu–Ga precursor film onto a molybdenum substrate, followed by the electrodeposition of a Cu–In–Se thin film. The resulting CuGa/CuInSe bilayer is then annealed at 600°C for 60 min in flowing Argon to form a CIGS thin film. The individual precursor films and subsequent CIGS films were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and Auger electron spectroscopy. The as-deposited precursor films were found to be crystalline with a crystal structure matching that of CuGa₂. The annealed bi-layers were found to have the same basic chalcopyrite structure of CuInSe₂, but with peak shifts due to the Ga incorporation. Energy dispersive spectroscopy results show that the observed shifts correlate to the composition of the films.     

Preparation of Cu(In,Ga)(S,Se)2 thin films by sequential evaporation and annealing in sulfur atmosphere

Cu(In,Ga)(S,Se)₂ thin films with high Ga/III ratio (around 0.8) were prepared by sequential evaporation from CuGaSe₂, CuInSe₂, In₂Se₃ and Ga₂Se₃ compounds and then annealing in H₂S gas atmosphere. The annealing temperature was varied from 400 to 500 °C. These samples were characterized by means of XRF, EPMA, XRD and SEM. The S/(S+Se) mole ratio in the thin films increased with increase in the annealing temperature, keeping the Cu, In and Ga contents nearly constant. The open circuit voltage increased and the short circuit current density decreased with increase in the annealing temperature. The best solar cell using Cu(In,Ga)(S,Se)₂ thin film with Ga/(In+Ga)=0.79 and S/(S+Se)=0.11 annealed at 400 °C demonstrated V_oc=535 mV, I_sc=13.3 mA/cm², FF=0.61 and efficiency=4.34% without AR-coating.     

Characterization of co-sputtered Cu-In alloy precursors for CuInSe2 thin films fabrication by close-spaced selenization

Sputtering technique for Cu–In precursor films fabrication using different Cu and In layer sequences have been widely investigated for CuInSe₂ production. But the CuInSe₂ films fabricated from these precursors using H₂Se or Se vapour selenization mostly exhibited poor microstructural properties. The co-sputtering technique for producing Cu–In alloy films and selenization within a close-spaced graphite box resulting in quality CuInSe₂ films was developed. All films were analysed using SEM, EDX, XRD and four-point probe measurements. Alloy films with a broad range of compositions were fabricated and XRD showed mainly In, CuIn₂ and Cu₁₁In₉ phases which were found to vary in intensities as the composition changes. Different morphological properties were displayed as the alloy composition changes. The selenized CuInSe₂ films exhibited different microstructural properties. Very In-rich films yielded the ODC compound with small crystal sizes whilst slightly In-rich or Cu-rich alloys yielded single phase CuInSe₂ films with dense crystals and sizes of about 5 μm. Film resistivities varied from 10⁻²–10⁸ Ω cm. The films had compositions with Cu/In of 0.40–2.3 and Se/(Cu+In) of 0.74–1.35. All CuInSe₂ films with the exception of very Cu-rich ones contained high amount of Se (>50%).     

A superstrate solar cell based on In2(Se,S)3 and CuIn(Se,S)2 thin films fabricated by electrodeposition combined with annealing

Stacked thin films composed of In₂(Se,S)₃ and CuIn(Se,S)₂ layers were grown on a fluorine-doped tin oxide (FTO)-coated glass substrate using electrodeposition of the corresponding selenide (In₂Se₃ and CuInSe₂) precursors followed by annealing in H₂S flow (5% in Ar). Structural characterizations of both layers revealed that the resulting film quality strongly depended on annealing conditions of both CuIn(Se,S)₂ and In₂(Se,S)₃ layers: a compact and uniform film was obtained by annealing both layers at 400 °C. Performance of Au/CuIn(Se,S)₂/In₂(Se,S)₃/FTO superstrate-type solar cells also followed these structural characteristics, i.e., a preliminary conversion efficiency of 2.9% was obtained on the device based on 400 °C-annealed In₂(Se,S)₃ and CuIn(Se,S)₂ layers.     

Mechanistic investigation on tuning the conductivity type of cuprous oxide (Cu2O) thin films via deposition potential

The conductivity type of cuprous oxide (Cu₂O) thin films is tuned by controlling the deposition potential of an electrochemical process in an acid cupric acetate solution containing sodium dodecyl sulfate. The morphology and chemical composition of the deposited Cu₂O films are studied by SEM, XRD and XPS. The change of the conductivity type of Cu₂O films is further studied through zero-bias photocurrent and Mott-Schottky measurements. The results indicate that the Cu₂O films behave as n-type semiconductors when the overpotentials are low (potentials higher than ?0.05 V) and p-type semiconductors when the overpotentials are high (potentials lower than ?0.10 V). The transformation of conductivity from n-type to p-type comes from the competition reactions between forming Cu₂O and forming metallic Cu from Cu²⁺. When the potential is lower than ?0.10 V, most of Cu²⁺ are consumed by the growth of metallic Cu at the film/solution interface, so that the Cu²⁺ provided to grow Cu₂O film are insufficient and copper vacancies form in the film, leading to the p-type conductivity.     

Comparison of point defects in CuInSe2 and CuGaSe2 single crystals

Hall-effect and photoluminescence measurements have been carried out on as-grown and In/Ga-annealed CuInSe₂ and CuGaSe₂ single crystals grown by chemical vapor transport. Various defect levels in these related compounds have been identified and compared. V_Cu and V_Se show similar properties and activation energies in both materials. A tremendous difference is observed in the behavior of III_Cu antisite defects. Ga_Cu levels in CuGaSe₂ are much deeper than In_Cu in CuInSe₂, and furthermore, the formation of In_Cu is much easier compared to Ga_Cu. This is related to the higher formation energy of Ga_Cu in CuGaSe₂. Due to this difference in the defect chemistry of both compounds, it has not been possible until now, to prepare n-type CuGaSe₂ crystals, whereas CuInSe₂ is easily transformed from p- to n-type by annealing in vacuum or In-atmosphere.     

The formation of CuInSe2 thin film solar cell absorbers from electroplated precursors with varying selenium content

We present results from real-time X-ray diffraction experiments on the formation of CuInSe₂ solar cell absorbers by annealing precursors, produced by simultaneous electrodeposition of copper, indium and selenium. The investigations reveal, that a reduced amount of electrochemically deposited selenium is the decisive parameter in order to realise a chalcopyrite formation behaviour as observed for sputtered stacked elemental layer (SEL) precursors. A simultaneous electrodeposition of the elements copper, indium and selenium in the molar ratio 1:1:2 of the chalcopyrite CuInSe₂ leads to the formation of binary copper and indium selenides during the electrodeposition process. The existence of binary selenides besides the intermetallic phase Cu₁₁In₉ as initial phases leads to an unfavourable absorber morphology. This can be explained by the observed semiconductor formation mechanism. A reduction of the deposited amount of selenium favours the formation of the intermetallic compound Cu₁₁In₉ and reduces the amount of binary selenides. These precursors show a formation behaviour and resulting absorber morphology as known for sputtered SEL precursors.     

Selenization of Cu and In thin films for the preparation of selenide photo-absorber layers in solar cells using Se vapour source

Gas phase selenization of vacuum deposited Cu and In thin films employing an elemental Se vapour source is demonstrated as an essential first step in the search for optimized process parameters for the formation of single phase CuInSe₂ materials suitable for solar cell applications. The selenization was accomplished in Se vapour, derived from an elemental Se source, held at 240–260°C. This source was placed in a flow of nitrogen gas at 500 Torr to transport the Se vapour to the metal films. The selenization reaction readily occurs at Cu and In films kept at 340–400°C. Lower selenization temperatures invariably lead to the formation of Cu and In selenides with well defined crystalline microstructures. Hexagonal CuSe with an excess of Se in the matrix is the equilibrium growth phase, while the cubic Cu_2−xSe phase evolves under conditions of excess Se flux. Selenization of the In films consistently led to the formation of the β-form of hexagonal In₂Se₃. At high selenization temperatures (400°C), while the β-form still emerges as the major component, traces of the α-form of In₂Se₃ are also detected. Detailed X-ray diffraction, electron probe analysis and microstructure data are presented.     

Depth profile analysis of CuInSe2 (CIS) thin films grown by the electrodeposition technique

In this study, we report the results obtained from the auger electron spectroscopy (AES) depth profiling of CIS thin films grown by the electrodeposition technique. This result enables one to do a comparison between the bulk and superficial elemental compositions. The AES result is also compared with that obtained by the inductively coupled plasma (ICP) spectroscopy. These results support our proposition that the electrodeposited CIS film has a Cu-rich bulk region and an In rich surface, which leads to the formation of an n-layer (CuIn₂Se_3.5) on the top of the p-type CIS (CuInSe₂) phase     

Preparation of CuInS2 films with sufficient sulfur content and excellent morphology by one-step electrodeposition

One-step electrodeposition using sodium thiosulfate (Na₂S₂O₃) as a sulfur source has been studied for the preparation of Cu---In---S thin films. A deposited film is found to have a sufficiently high sulfur content compared with films deposited using thiourea as a sulfur source. The film deposited using Na₂S₂O₃ is also found to have an excellent morphology compared with electrodeposited Cu---In precursors. Predominant factors to govern film composition, In/Cu and S/(Cu + In) ratios, are also investigated in this study. An HC1 content added in order to decompose S₂O₃²⁻ ions in the solution is found to be one of the important factors to control composition of deposited films. A sulfur cocentration in the solution influences not only S/(Cu + In) ratio but also In/Cu ratio in the film. Reproducibility of film composition is deteriorated as the solution temperature increases.     

Cathodic electrodeposition of Cu2S thin film for solar energy conversion

Cathodic electrodeposition in the presence of EDTA in aqueous solution was used to prepare Cu₂S thin film deposited on Ti substrate. The effect of deposition potential, concentration and deposition time was studied to determine the optimum condition for electro-deposition process. Cyclic voltammetry was performed to elucidate the electrodic processes that occur while potentials for electrodeposition were applied to determine the optimum potential for electrodeposition. The thin films are characterised by X-ray diffractometry. The photoactivity of the deposited films and their conduction types were evaluated using photoelectrochemical technique. The band gap energy and type of optical transitions were determined from optical absorbance data.     

Real-time investigations on the formation of CuInSe2 thin film solar cell absorbers from electrodeposited precursors

In this article, we present results of a detailed real-time X-ray diffraction (XRD) study on the formation of CuInSe₂ from electroplated precursors. The solid-state reactions observed during the selenisation of three different types of precursors are presented. The first type of precursors (I) consists of the nanocrystalline phases Cu_2−xSe and InSe at room temperature, which react to CuInSe₂ starting at 470 K. The second type of precursor (II) shows an inhibited CuInSe₂ formation out of the initial phases Cu_2−xSe and γ-In₂Se₃ starting at 400 K. The third precursor type (III) shows completely different selenisation behaviour. Starting from the intermetallic compound Cu₁₁In₉ and amorphous selenium, the formation of the binary selenides In₄Se₃ and CuSe is observed after the melting point of selenium at 494 K. After selenium transfer reactions, the compound semiconductor CuInSe₂ is formed out of Cu_2−xSe and InSe. This type (III) reaction path is well known for the selenisation of SEL precursors (stacked elemental layers of sputtered copper and indium and thermally evaporated selenium).     

Stoichiometry controlled conversion efficiency in nanostructured heterojunction solar cell of CdS/CuInSXSe2−X grown by chemical ion exchange method at room temperature

Here in the present paper, we report on growth of stoichiometric and nonstoichiometric nanostructured heterojunction solar cell of CdS/CuInS_XSe_2-X varying X from 0 to 2 in the interval of 0.5 using cost effective, simple, chemical ion exchange method at room temperature on ITO glass substrate. The as-grown varying composition solar cells annealed at 200 °C in air and characterized for structural, compositional, optical and illumination studies. The X-ray diffraction pattern obtained from CdS/CuInS_XSe_2-X solar cell confirms the formation of CuInSe₂, CuInS_0.5Se_1.5, CuInS₁Se₁, CuInS_1.5Se_0.5 and CuInS₂ phases having tetragonal structure with varying crystallite size from 19, 19.37, 28, 33 and 20 nm respectively. The energy dispersive X-ray analysis (EDAX) confirms the expected elemental composition in the heterojunction solar cell. Optical absorbance analysis confirms composition controlled electronic transitions in the thin films while energy band gap observed to be red shifted with increase the value of X. The solar energy conversion efficiency achieved upon illuminating to 100 mW/cm² observed to be 0.27%, 0.06%, 0.17%, 0.02% and 0.23% for CuInSe₂, CuInS_0.5Se_1.5, CuInS₁Se₁, CuInS_1.5Se_0.5 and CuInS₂ respectively, which correspond for stoichiometric dependent electron-hole pair generation and separation phenomenon.     

Growth, structural and optical properties of copper indium diselenide thin films deposited by thermal evaporation method

Copper indium diselenide (CuInSe₂) compound was synthesized by reacting its constituent’s elements copper, indium and selenium in near stoichiometric proportions (i.e. 1:1:2 with 5% excess selenium) in an evacuated quartz ampoule. Synthesized pulverized compound material was used as an evaporant material to deposit thin films of CuInSe₂ onto organically cleaned sodalime glass substrates, held at different temperatures (300-573 K), by means of single source thermal evaporation method. The phase structure and the composition of chemical constituents present in the synthesized compound and thin films have been investigated using X-ray diffraction and energy dispersive X-ray analysis, respectively. The investigations show that CuInSe₂ thin films grown above 423 K are single phase, having preferred orientation of grains along the (112) direction, and having near stoichiometric composition of elements. The surface morphology of CuInSe₂ films, deposited at different substrate temperatures, has been studied using the atomic force microscopy to estimate its surface roughness. An analysis of the transmission spectra of CuInSe₂ films, recorded in the wavelength range of 500-1500 nm, revealed that the optical absorption coefficient and the energy band gap for CuInSe₂ films, deposited at different substrate temperatures, are ∼10⁴ cm⁻¹ and 1.01-1.06 eV, respectively. The transmission spectrum was analyzed using iterative method to calculate the refractive index and the extinction coefficient of CuInSe₂ thin film deposited at 523 K. The Hall effect measurements and the temperature dependence of the electrical conductivity of CuInSe₂ thin films, deposited at different substrate temperatures, revealed that the films had electrical resistivity in the range of 0.15-20 ohm cm, and the activation energy 82-42 meV, both being influenced by the substrate temperature.