Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

A NGCC power plant with a CO2 post-combustion capture option. Optimal economics for different generation/capture goals

Fossil fuel power plants are one of the major sources of electricity generation, although invariably release greenhouse gases. Due to international treaties and countries regulations, CO₂ emissions reduction is increasingly becoming key in the generators’ economics. NGCC power plants constitute a widely used generation technology, from which CO₂ capture through a post-combustion and MEA absorption option constitutes a technological challenge due to the low concentration of pollutants in the flue gas and the high energy requirements of the sequestration process.     

Dynamic modeling and validation of absorber and desorber columns for post-combustion CO2 capture

The paper evaluates, by modeling and simulation, carbon dioxide capture in aqueous solution of mono-ethanolamine (MEA) in packed absorption columns to be used in power sector for reducing greenhouse gas emissions. The mathematical model of carbon dioxide absorption and rich amine regeneration process includes transfer processes: mass and heat to study the coupled effect of temperature and concentration on the rate of absorption. The reaction kinetics and the vapor-liquid equilibrium (VLE) are other important parts of the model. The present dynamic mathematical model can be used to analyze the absorption rate, to understand the micro level interaction of various processes taking place inside the absorption and desorption column, and to improve the overall design of the system.The aim of the project was to validate the absorber and desorber models, as well as to understand the dynamic behavior of the whole capture-regeneration steps.     

Dynamic modelling and analysis of post-combustion CO2 chemical absorption process for coal-fired power plants

Post-combustion capture by chemical absorption using MEA solvent remains the only commercial technology for large scale CO₂ capture for coal-fired power plants. This paper presents a study of the dynamic responses of a post-combustion CO₂ capture plant by modelling and simulation. Such a plant consists mainly of the absorber (where CO₂ is chemically absorbed) and the regenerator (where the chemical solvent is regenerated). Model development and validation are described followed by dynamic analysis of the absorber and regenerator columns linked together with recycle. The gPROMS (Process Systems Enterprise Ltd.) advanced process modelling environment has been used to implement the proposed work. The study gives insights into the operation of the absorber-regenerator combination with possible disturbances arising from integrated operation with a power generation plant. It is shown that the performance of the absorber is more sensitive to the molar L/G ratio than the actual flow rates of the liquid solvent and flue gas. In addition, the importance of appropriate water balance in the absorber column is shown. A step change of the reboiler duty indicates a slow response. A case involving the combination of two fundamental CO₂ capture technologies (the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing) is studied. The flue gas composition was altered to mimic that observed with the combination. There was an initial sharp decrease in CO₂ absorption level which may not be observed in steady-state simulations.     

Initial evaluation of the impact of post-combustion capture of carbon dioxide on supercritical pulverised coal power plant part load performance

Pulverised coal-fired plants often play an important role in electricity grids as mid-merit plants that can operate flexibly in response to changes in supply and demand. As a consequence, these plants are required to operate over a wide output range. This paper presents an initial evaluation of some potential impacts of adding post-combustion CO₂ capture on the part load performance of pulverised coal-fired plants. Preliminary results for ideal cases analysed using a simple high-level model indicate that post-combustion CO₂ capture could increase the options available to power plant operators. In particular, solvent storage could allow higher effective plant load factors to be achieved to assist with capital recovery while still permitting flexible operation for grid support. A number of areas for more detailed analysis are identified.     

Dynamic modeling of CO2 absorption from coal-fired power plants into an aqueous monoethanolamine solution

Among carbon capture and storage (CCS), the post-combustion capture of carbon dioxide (CO₂) by means of chemical absorption is actually the most developed process. Steady state process simulation turned out as a powerful tool for the design of such CO₂ scrubbers. Besides steady state modeling, transient process simulations deliver valuable information on the dynamic behavior of the system. Dynamic interactions of the power plant with the CO₂ separation plant can be described by such models. Within this work a dynamic process simulation model of the absorption unit of a CO₂ separation plant was developed. For describing the chemical absorption of CO₂ into an aqueous monoethanolamine solution a rate based approach was used. All models were developed within the Aspen Custom Modeler^® simulation environment. Thermo physical properties as well as transport properties were taken from the electrolyte non-random-two-liquid model provided by the Aspen Properties^® database. Within this work two simulation cases are presented. In a first simulation the inlet temperature of the flue gas and the lean solvent into the absorber column was changed. The results were validated by using experimental data from the CO₂SEPPL test rig located at the Dürnrohr power station. In a second simulation the flue gas flow to the separation plant was increased. Due to the unavailability of experimental data a validation of the results from the second simulation could not be achieved.     

Impact of liquid absorption process development on the costs of post-combustion capture in Australian coal-fired power stations

Australian power generators produce approximately 170 TWh per annum of electricity using black and brown coals that accounts for 170 Mtonne of CO₂ emissions per annum or over 40% of anthropogenic CO₂ emissions in Australia. This paper describes the results of a techno-economic evaluation of liquid absorption based post-combustion capture (PCC) processes for both existing and new pulverised coal-fired power stations in Australia. The overall process designs incorporate both the case with continuous capture and the case with the flexibility to switch a CO₂ capture plant on or off depending upon the demand and market price for electricity, and addresses the impact of the presently limited emission controls on the process cost. The techno-economic evaluation includes both air and water cooled power and CO₂ capture plants, resulting in cost of power generation for the situations without and with PCC. Whilst existing power plants in Australia are all water cooled sub-critical designs, the new power plants are deemed to range from supercritical single reheat to ultra-supercritical double reheat designs, with a preference for air-cooling. The process evaluation also includes a detailed sensitivity analysis of the thermodynamic properties of liquid absorbent for CO₂ on the overall costs. The results show that for a meaningful decrease in the efficiency and cost penalties associated with the post combustion CO₂ capture, a novel liquid sorbent will need to have heat of absorption/desorption, sensible heat and heat of vaporisation around 50% less in comparison with 30% (w/w) aqueous MEA solvent. It also shows that the impact of the capital costs of PCC processes is quite large on the added cost of generation. The results can be used to prioritise PCC research in an Australian context.     

Optimization of post-combustion CO2 process using DEA-MDEA mixtures

This paper presents optimal operating conditions for the post-combustion CO₂ capture process utilizing aqueous amine solutions obtained using a process simulator (HYSYS). Three alkanolamine solutions (Methyldiethanolamine MDEA, DiEthanolAmine DEA and MDEA-DEA mixture) are considered to study the performance of the capture process.The design problem addressed in this paper requires specifying the optimal operating conditions (inlet and outlet temperature of the lean solution stream on the absorber, CO₂ loading, amine composition and flow rates, among others) to achieve the given CO₂ emission targets at a minimum total annual cost. A detailed objective function including total operating costs and investment is considered.The influence of the variation of CO₂ reduction targets and the mixing proportion of amines on the total annual cost is analyzed in detail. Numerical results are presented and discussed using different case studies.The results demonstrate that process simulators can be used as a powerful tool not only to simulate but also to optimize the most important design parameters of the post-combustion CO₂ capture process.     

Preliminary analysis of process flow sheet modifications for energy efficient CO2 capture from flue gases using chemical absorption

The energy penalty associated with solvent based capture of CO₂ from power station flue gases can be reduced by incorporating process flow sheet modifications into the standard process. A review of modifications suggested in the open and patent literature identified several options, primarily intended for use in the gas processing industry. It was not immediately clear whether these options would have the same benefits when applied to CO₂ capture from near atmospheric pressure combustion flue gases. Process flow sheet modifications, including split flow, rich split, vapour recompression, and inter-stage cooling, were therefore modelled using a commercial rate-based simulation package. The models were completed for a Queensland (Australia) based pilot plant running on 30% MEA as the solvent. The preliminary modelling results showed considerable benefits in reducing the energy penalty of capturing CO₂ from combustion flue gases. Further work will focus on optimising and validating the most relevant process flow sheet modifications in a pilot plant.     

Formation of NOx precursors during the pyrolysis of coal and biomass. Part VI. Effects of gas atmosphere on the formation of NH3 and HCN

Our results indicate that the gas atmosphere surrounding coal/char particles can greatly affect the formation of NH₃ and HCN through its influence on the availability of H radicals. Based on our results, it is believed that the chemisorption of CO₂ on the nascent char surface can consume H radicals or block the access of N-sites by H radicals for the formation of NH₃ and HCN. For the chars whose thermal cracking generates little H radicals, the gasification of char by CO₂ can also generate additional H radicals, enhancing the formation of NH₃. However, even gasification of char in CO₂ at 950 °C does not lead to the formation of HCN. The oxidation of coal with 4% O₂ at low temperatures (400-600 °C) leads to the formation of HCN as well as NH₃ due to the enhanced formation of (H) radicals. The gasification of coal with 15% H₂O drastically enhances the formation of NH₃ due to the greatly enhanced availability of H as an intermediate between the reactions of H₂O and char. These results support our reaction mechanisms proposed previously, emphasising the importance of H on the formation of NH₃ and HCN during pyrolysis, which can also be extended to the conversion of coal-N during gasification.     

Experimental programme in CIUDEN's CO2 capture technology development plant for power generation

Energy projections made by the World Energy Council, the International Energy Agency (IEA) and the US Energy Information Administration give similar pictures of the dominant role of fossil fuel in the future primary energy global demand and the necessity of incorporating CCS Technologies as part of the portfolio of solutions to reach the target world emission reduction in the coming years. Without CCS, CO₂ emission levels by 2050 are expected to increase by 70%.One of the most relevant initiatives for the deployment of CCS technologies is promoted by the Spanish Government through the institution Fundacion Ciudad de la Energia (CIUDEN). CIUDEN is developing a complete programme focusing on the development of CCT and CCS technologies in Europe.CIUDEN's CO₂ capture programme includes the construction and operation of a Technology Development Plant (TDP) in NW Spain (El Bierzo). The construction of the installation started in November 2008 and incorporates the following technologies: fuel preparation system, pulverised coal boiler (20 MWth), circulating fluidized bed boiler (30 MWth), biomass gasifier (3 MWth), flue gas cleaning train for NO_x, dust and SO_x, and CO₂ processing unit.This paper describes CIUDEN's TDP for CO₂ capture, focusing on the particularities of the installation and design, and especially on the PC unit and equipment required for its operation. The experimental programme currently under way is also described.Results are expected to be an extraordinary advance in the development and strengthening of CCT and CCS technologies, particularly oxycombustion.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

Techno-economic evaluation of a PVAm CO2-selective membrane in an IGCC power plant with CO2 capture

Published data for an operating power plant, the ELCOGAS 315 MWe Puertollano plant, has been used as a basis for the simulation of an integrated gasification combined cycle process with CO₂ capture. This incorporated a fixed site carrier polyvinylamine membrane to separate the CO₂ from a CO-shifted syngas stream. It appears that the modified process, using a sour shift catalyst prior to sulphur removal, could achieve greater than 85% CO₂ recovery at 95 vol% purity. The efficiency penalty for such a process would be approximately 10% points, including CO₂ compression. A modified plant with CO₂ capture and compression was calculated to cost €2320/kW, producing electricity at a cost of 7.6 € cents/kWh and a CO₂ avoidance cost of about €40/tonne CO₂.     

Post-combustion CO2 capture with chemical absorption: A state-of-the-art review

Global concentration of CO₂ in the atmosphere is increasing rapidly. CO₂ emissions have an impact on global climate change. Effective CO₂ emission abatement strategies such as Carbon Capture and Storage (CCS) are required to combat this trend. There are three major approaches for CCS: post-combustion capture, pre-combustion capture and oxyfuel process. Post-combustion capture offers some advantages as existing combustion technologies can still be used without radical changes on them. This makes post-combustion capture easier to implement as a retrofit option (to existing power plants) compared to the other two approaches. Therefore, post-combustion capture is probably the first technology that will be deployed. This paper aims to provide a state-of-the-art assessment of the research work carried out so far in post-combustion capture with chemical absorption. The technology will be introduced first, followed by required preparation of flue gas from power plants to use this technology. The important research programmes worldwide and the experimental studies based on pilot plants will be reviewed. This is followed by an overview of various studies based on modelling and simulation. Then the focus is turned to review development of different solvents and process intensification. Based on these, we try to predict challenges and potential new developments from different aspects such as new solvents, pilot plants, process heat integration (to improve efficiency), modelling and simulation, process intensification and government policy impact.     

A novel LiTi2(PO4)3/MnO2 hybrid supercapacitor in lithium sulfate aqueous electrolyte

In this work, carbon-coated lithium-ion intercalated compound LiTi₂(PO₄)₃ and MnO₂ have been synthesized and they deliver a capacity of 90 and 60 mAh/g in 1 M Li₂SO₄ neutral aqueous electrolyte within safe potentials without O₂ and H₂ evolution, respectively. The novel hybrid supercapacitor in which MnO₂ was used as a positive electrode and carbon-coated LiTi₂(PO₄)₃ as a negative electrode was assembled and the LiTi₂(PO₄)₃/MnO₂ hybrid supercapacitor showed a sloping voltage profile from 0.7 to 1.9 V, at an average voltage near 1.3 V, and delivers a capacity of 36 mAh/g and an energy density of 47 Wh/kg based on the total weight of the active electrode materials. It exhibits a desirable profile and maintains over 80% of its initial energy density after 1000 cycles. The hybrid supercapacitor also exhibit an excellent rate capability, even at a power density of 1000 W/kg, it has a specific energy 25 Wh/kg compared with 43 Wh/kg at the power density about 200 W/kg.     

Post-combustion CO2 capture process: Equilibrium stage mathematical model of the chemical absorption of CO2 into monoethanolamine (MEA) aqueous solution

This paper deals with the modeling and optimization of the chemical absorption process to CO₂ removal using monoethanolamine (MEA) aqueous solution. Precisely, an optimization mathematical model is proposed to determine the best operating conditions of the CO₂ post-combustion process in order to maximize the CO₂ removal efficiency. Certainly, the following two objective functions are considered for maximization: (a) ratio between the total absorbed CO₂ and the total heating and cooling utilities and (b) ratio between total absorbed CO₂ and the total amine flow-rate.Temperature, composition and flow-rate profiles of the aqueous solution and gas streams along the absorber and regenerator as well as the reboiler and condenser duties are considered as optimization variables. The number of trays or height equivalent to a theoretical plate (HETP) on the absorber and regenerator columns as well as the CO₂ composition in flue gas are treated as model parameters. Correlations used to compute physical-chemical properties of the aqueous amine solution are taken from different specialized literature and are valid for a wide range of operating conditions. For the modeling, both columns (absorber and regenerator) are divided into a number of segments assuming that liquid and gas phases are well mixed.GAMS (General Algebraic Modeling System) and CONOPT are used, respectively, to implement and to solve the resulting mathematical model.The robustness and computational performance of the proposed model and a detailed discussion of the optimization results will be presented through different case studies. Finally, the proposed model cannot only be used as optimizer but also as a simulator by fixing the degree of freedom of the equation system.     

Modelling reactive absorption of CO2 in packed columns for post-combustion carbon capture applications

A rate-based process model for the reactive absorption of carbon dioxide (CO₂) from a gas mixture into an aqueous monoethanolamine (MEA) solution in a packed column is developed. The model is based on the fast second-order kinetics for the CO₂-MEA reactions and takes into account the mass transfer resistances. The heat effects associated with the absorption and chemical reaction are included through energy balances in the gas and liquid phases. Appropriate correlations for the key thermodynamic and transport properties and for the gas-liquid mass transfer are incorporated into the model to ensure reliable predictions. The model predictions are validated by simulating a series of experiments conducted in pilot and industrial scale absorption columns with random and structured packings reported in the literature. Comparisons between the simulation results and the experimental data reveal good quality predictions of the gas phase CO₂ and MEA concentrations and the liquid temperature along the column height. The sensitivity studies reveal that the correlations for the gas- and liquid-film mass transfer coefficients given by Onda et al. (1968) provide better predictions than the penetration theory of Higbie (1935) and the correlation of Bravo et al. (1985).     

Simultaneous reduction of NOx and SO2 emissions from coal combustion by calcium magnesium acetate

The potential of calcium magnesium acetate (CMA) as a medium for the simultaneous control of NO_x and SO_x emissions has been investigated using a pulverized coal combustion rig operating at 80 kW. A US and a UK coal of significantly different sulphur contents were used as primary fuel and CMA was injected in solution form into the combustion gases by horizontally opposed twin-fluid atomisers at temperatures of 1100-1200 °C. SO₂ reductions typically greater than 80 and 70% were found for initial SO₂ levels of 1000 and 1500 ppm, respectively, at Ca/S ratios greater than 2.5. There did not appear to be significant limitation on sulphation by pore blockage using CMA due to the open structure formed during calcination and there is clear potential for zero SO₂ emissions at higher Ca/S ratios. The Ca content of the CMA in the form of CaO, via a droplet drying/particle calcination process, absorbs SO₂ by sulphation processes by penetration into the open pore structure of these particles. The effect of primary zone stoichiometry (λ₁=1.05, 1.15 and 1.4) on NO_x reduction was investigated for a range of CMA feed rates up to a coal equivalent of 24% of the total thermal input. NO_x reductions of 80, 50 and 30% were achieved at a primary zone stoichiometry of λ₁=1.05, 1.15 and 1.4, respectively, for a reburn zone residence time of 0.8 s. At lower equivalent reburn fuel fractions, coal gave greater NO_x reductions than CMA but similar levels were achieved above Rff=18%. The mechanism for NO_x reduction involves the organic fraction of CMA which pyrolyses into hydrocarbon fragments (CH_i), but to a lesser degree than coal, which may then react with NO_x in a manner similar to a conventional ‘reburn’ mechanism where NO_x is partly converted to N₂ depending on the availability of oxygen.     

Sorbent attrition in a carbonation/calcination pilot plant for capturing CO2 from flue gases

There is increasing interest in CO₂ looping cycles that involve the repeated calcination and carbonation of the sorbent as a way to capture CO₂ from flue gases during the carbonation step and the generation of a pure stream of CO₂ in the oxyfired calcination step. In particular, attrition of the material in these interconnected fluidized bed reactors is a problem of general concern. Attrition of limestone derived materials has been studied in fluidized bed systems by numerous authors. In this work, we have investigated the attrition of two limestones used in a system of two interconnected circulating fluidized bed reactors operating in continuous mode as carbonation and calciner reactors. We observed a rapid initial attrition of both limestones during the calcination step which was then followed by a highly stable period (up to 140 h of added circulation for one of the limestones) during which particle size changes were negligible. This is consistent with previous observations of attrition in other systems that employ these materials. However, a comparison of the attrition model constants with the data reported in the literature showed the two limestones to be particularly fragile during the initial calcination and the first few hours of circulation. Thus, a careful choice of limestone based on its attrition properties must be taken into account in designing future carbonate looping systems.     

Design and operation of pilot plant for CO2 capture from IGCC flue gases by combined cryogenic and hydrate method

This project is a trial conducted under contract with CO₂CRC, Australia of a new CO₂ capture technology that can be applied to integrated gasification combined cycle power plants and other industrial gasification facilities. The technology is based on combination of two low temperature processes, namely cryogenic condensation and the formation of hydrates, to remove CO₂ from the gas stream. The first stage of this technology is condensation at −55 °C where CO₂ concentration is expected to be reduced by up to 75 mol%. Remaining CO₂ is captured in the form of solid hydrate at about 1 °C reducing CO₂ concentration down to 7 mol% using hydrate promoters. This integrated cryogenic condensation and CO₂ hydrate capture technology hold promise for greater reduction of CO₂ emissions at lower cost and energy demand. Overall, the process produced gas with a hydrogen content better than 90 mol%. The concentrated CO₂ stream was produced with 95-97 mol% purity in liquid form at high pressure and is available for re-use or sequestration. The enhancement of carbon dioxide hydrate formation and separation in the presence of new hydrate promoter is also discussed. A laboratory scale flow system for the continuous production of condensed CO₂ and carbon dioxide hydrates is also described and operational details are identified.