Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

Comparative assessment of sub-critical versus advanced super-critical oxyfuel fired PF boilers with CO2 sequestration facilities

This work focuses on the techno-economic assessment of bituminous coal fired sub- and super-critical pulverised fuel boilers from an oxyfuel based CO₂ capture point of view. At the initial stage, two conventional power plants with a nominal power output of above 600 MWe based on the above steam cycles are designed, simulated and optimised. Built upon these technologies, CO₂ capture facilities are incorporated within the base plants resulting in a nominal power output of 500 MWe. In this manner, some sensible heat generated in the air separation unit and the CO₂ capture train can be redirected to the steam cycle resulting in a higher plant efficiency. The simulation results of conventional sub- and super-critical plants are compared with their CO₂ capture counterparts to disclose the effect of sequestration on the overall system performance attributes. This systematic approach allows the investigation of the effects of the CO₂ capture on both cycles. In the literature, super-critical plants are often considered for a CO₂ capture option. These, however, are not based on a systematic evaluation of these technologies and concentrate mainly on one or two key features. In this work several techno-economic plant attributes such as the fuel consumptions, the utility usages, the plant performance parameters as well as the specific CO₂ generation and capture rates are calculated and weighed against each other. Finally, an economic evaluation of the system is conducted along with sensitivity analyses in connection with some key features such as discounted cash flow rates, capital investments and plant efficiencies as well as fuel and operating costs.     

Techno-economic modelling and cost functions of CO2 capture processes

The paper presents the techno-economic modelling of CO₂ capture process in coal-fired power plants. An overall model is being developed to compare carbon capture and sequestration options at locations within the UK, and for studies of the sensitivity of the cost of disposal to changes in the major parameters of the most promising solutions identified. Technological options of CO₂ capture have been studied and cost estimation relationships (CERs) for the chosen options calculated. Created models are related to the capital, operation and maintenance cost. A total annualised cost of plant electricity output and amount of CO₂ avoided have been developed. The influence of interest rates and plant life has been analysed as well. The CERs are included as an integral part of the overall model.     

Techno-economic evaluation of advanced IGCC lignite coal fuelled power plants with CO2 capture

The techno-economic evaluation of four novel integrated gasification combined cycle (IGCC) power plants fuelled with low rank lignite coal with CO₂ capture facility has been investigated using ECLIPSE process simulator. The performance of the proposed plants was compared with two conventional IGCC plants with and without CO₂ capture. The proposed plants include an advanced CO₂ capturing process based on the Absorption Enhanced Reforming (AER) reaction and the regeneration of sorbent materials avoiding the need for sulphur removal component, shift reactor and/or a high temperature gas cleaning process. The results show that the proposed CO₂ capture plants efficiencies were 18.5–21% higher than the conventional IGCC CO₂ capture plant. For the proposed plants, the CO₂ capture efficiencies were found to be within 95.8–97%. The CO₂ capture efficiency for the conventional IGCC plant was 87.7%. The specific investment costs for the proposed plants were between 1207 and 1479 €/kW_e and 1620 €/kW_e and 1134 €/kW_e for the conventional plants with and without CO₂ capture respectively. Overall the proposed IGCC plants are cleaner, more efficient and produce electricity at cheaper price than the conventional IGCC process.     

Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants

CO₂ capture systems based on the carbonation/calcination loop have gained rapid interest due to promising carbonator CO₂ capture efficiency, low sorbent cost and no flue gases treatment is required before entering the system. These features together result in a competitively low cost CO₂ capture system. Among the key variables that influence the performance of these systems and their integration with power plants, the carbonation conversion of the sorbent and the heat requirement at calciner are the most relevant. Both variables are mainly influenced by CaO/CO₂ ratio and make-up flow of solids. New sorbents are under development to reduce the decay of their carbonation conversion with cycles. The aim of this study is to assess the competitiveness of new limestones with enhanced sorption behaviour applied to carbonation/calcination cycle integrated with a power plant, compared to raw limestone. The existence of an upper limit for the maximum average capture capacity of CaO has been considered. Above this limit, improving sorbent capture capacity does not lead to the corresponding increase in capture efficiency and, thus, reduction of CO₂ avoided cost is not observed. Simulations calculate the maximum price for enhanced sorbents to achieve a reduction in CO₂ removal cost under different process conditions (solid circulation and make-up flow). The present study may be used as an assessment tool of new sorbents to understand what prices would be competitive compare with raw limestone in the CO₂ looping capture systems.     

Economic implications of oxyfuel application in a lignite-fired power plant

Scope of the work presented in this paper is to examine and evaluate the application of the oxyfuel combustion CO₂ capture technology in a lignite-fired power plant from an economic point of view. Results from simulations dealing with the most important features for CO₂ reduction are performed. The operational characteristics, the efficiency penalties as well as the net efficiency reduction emerging from the Greenfield application of the oxyfuel technology are presented.CO₂ capture costs and the energy requirements associated with the oxyfuel method affect significantly the cost of electricity. This paper focuses on the analysis of the techno-economic factors that result in the increase of the cost of electricity in comparison with the conventional air-fired power plant. For this reason a typical Greek lignite power plant is used as a reference case. Any technical, economic and financial assumptions applied provide a common basis for both power plants (i.e., conventional and oxyfuel) for the assessment of the change of the cost of electricity and the CO₂ capture cost. The oxyfuel simulations are performed by taking into account the adoption of measures for the exploitation of heat that would otherwise be wasted. Such measures concern both the water/steam cycle and the gas flows (e.g., the oxygen flow). Heat integration from processes - such as the air separation, the CO₂ compression and purification and the flue gas treatment - is adopted in order to lower as much as possible the efficiency penalty.The cycle calculations have been performed using the thermodynamic cycle calculation software ENBIPRO (ENergie-BIllanz-PROgram). ENBIPRO is a powerful tool for heat and mass balance solving of complex thermodynamic circuits, calculation of efficiency, exergetic and exergoeconomic analysis of power plants. The software code models all pieces of equipment that usually appear in power plant installations and can accurately calculate all thermodynamic properties (temperature, pressure, enthalpy) at each node of the thermodynamic circuit, power consumption of each component, flue gas composition, etc. The code has proven its validity by accurately simulating a large number of power plants and through comparison of the results with other commercial software (Stamatelopoulos GN. Calculation and optimisation of power plant thermodynamic cycles. VDI-Regulations. Series 6, No. 340. Braunchweig, Mechanical Engineering Department; 1996 [in German]).     

Initial evaluation of the impact of post-combustion capture of carbon dioxide on supercritical pulverised coal power plant part load performance

Pulverised coal-fired plants often play an important role in electricity grids as mid-merit plants that can operate flexibly in response to changes in supply and demand. As a consequence, these plants are required to operate over a wide output range. This paper presents an initial evaluation of some potential impacts of adding post-combustion CO₂ capture on the part load performance of pulverised coal-fired plants. Preliminary results for ideal cases analysed using a simple high-level model indicate that post-combustion CO₂ capture could increase the options available to power plant operators. In particular, solvent storage could allow higher effective plant load factors to be achieved to assist with capital recovery while still permitting flexible operation for grid support. A number of areas for more detailed analysis are identified.     

Design and operation of pilot plant for CO2 capture from IGCC flue gases by combined cryogenic and hydrate method

This project is a trial conducted under contract with CO₂CRC, Australia of a new CO₂ capture technology that can be applied to integrated gasification combined cycle power plants and other industrial gasification facilities. The technology is based on combination of two low temperature processes, namely cryogenic condensation and the formation of hydrates, to remove CO₂ from the gas stream. The first stage of this technology is condensation at −55 °C where CO₂ concentration is expected to be reduced by up to 75 mol%. Remaining CO₂ is captured in the form of solid hydrate at about 1 °C reducing CO₂ concentration down to 7 mol% using hydrate promoters. This integrated cryogenic condensation and CO₂ hydrate capture technology hold promise for greater reduction of CO₂ emissions at lower cost and energy demand. Overall, the process produced gas with a hydrogen content better than 90 mol%. The concentrated CO₂ stream was produced with 95-97 mol% purity in liquid form at high pressure and is available for re-use or sequestration. The enhancement of carbon dioxide hydrate formation and separation in the presence of new hydrate promoter is also discussed. A laboratory scale flow system for the continuous production of condensed CO₂ and carbon dioxide hydrates is also described and operational details are identified.     

Competitiveness of CO2 capture from an industrial solid oxide fuel cell combined heat and power system in the early stage of market introduction

In this article, it was investigated whether potentially low-cost CO₂ capture from SOFC systems could enhance the penetration of SOFC in the energy market in a highly carbon-constrained society in the mid-term future (up to year 2025). The application of 5 MWe SOFC systems for industrial combined heat and power (CHP) generation was considered. For CO₂ capture, oxyfuel combustion of anode off-gas using commercially available technologies was selected. Gas turbine (GT-) CHP plant was considered to be the reference case.Technical results showed that despite the energy penalties due to CO₂ capture and compression, net electrical and heat efficiencies were nearly identical with or without CO₂ capture. This was due to higher heat recovery efficiency by separating SOFC off-gas streams for CO₂ capture. However, CO₂ capture significantly increased the required SOFC and heat exchanger areas.Economic results showed that for above 40-50 $ t⁻¹ CO₂ price, SOFC-CHP systems were more economical when equipped with CO₂ capture. CO₂ capture also enabled SOFC-CHP to compete with GT-CHP at higher cell stack production costs. At zero CO₂ price, cell stack production cost had to be as low as 140 kW⁻¹ for SOFC-CHP to outperform GT-CHP. At 100 $ t⁻¹ CO₂ price, the cell stack production cost requirement raised to 350 $ kW⁻¹. With CO₂ capture, SOFC-CHP still outperformed GT-CHP at a significantly higher cell stack production cost above 900 $ kW⁻¹.     

Results from trialling aqueous NH3 based post-combustion capture in a pilot plant at Munmorah power station: Absorption

Australia's Commonwealth Scientific and Industrial Research Organization (CSIRO) and Delta Electricity have developed, commissioned and operated an A$7 million aqueous NH₃ based post-combustion capture (PCC) pilot plant at the Munmorah black coal fired power station in Australia. The results from the pilot plant trials will be used to address the gap in know-how on application of aqueous NH₃ for post-combustion capture of CO₂ and other pollutants in the flue gas and explore the potential of the NH₃ process for application in the Australia power sector. This paper is one of a series of publications to report and discuss the experimental results obtained from the pilot plant trials and primarily focuses on the absorption section.The pilot plant trials have confirmed the technical feasibility of the NH₃ based capture process. CO₂ removal efficiency of more than 85% can be achieved even with low NH₃ content of up to 6 wt%. The NH₃ process is effective for SO₂ but not for NO in the flue gas. More than 95% of SO₂ in the flue gas is removed in the pre-treatment column using NH₃. The mass transfer coefficients for CO₂ in the absorber as functions of CO₂ loading and NH₃ concentration have been obtained based on pilot plant data.     

Techno-economic evaluation of a PVAm CO2-selective membrane in an IGCC power plant with CO2 capture

Published data for an operating power plant, the ELCOGAS 315 MWe Puertollano plant, has been used as a basis for the simulation of an integrated gasification combined cycle process with CO₂ capture. This incorporated a fixed site carrier polyvinylamine membrane to separate the CO₂ from a CO-shifted syngas stream. It appears that the modified process, using a sour shift catalyst prior to sulphur removal, could achieve greater than 85% CO₂ recovery at 95 vol% purity. The efficiency penalty for such a process would be approximately 10% points, including CO₂ compression. A modified plant with CO₂ capture and compression was calculated to cost €2320/kW, producing electricity at a cost of 7.6 € cents/kWh and a CO₂ avoidance cost of about €40/tonne CO₂.     

Dynamic modelling and analysis of post-combustion CO2 chemical absorption process for coal-fired power plants

Post-combustion capture by chemical absorption using MEA solvent remains the only commercial technology for large scale CO₂ capture for coal-fired power plants. This paper presents a study of the dynamic responses of a post-combustion CO₂ capture plant by modelling and simulation. Such a plant consists mainly of the absorber (where CO₂ is chemically absorbed) and the regenerator (where the chemical solvent is regenerated). Model development and validation are described followed by dynamic analysis of the absorber and regenerator columns linked together with recycle. The gPROMS (Process Systems Enterprise Ltd.) advanced process modelling environment has been used to implement the proposed work. The study gives insights into the operation of the absorber-regenerator combination with possible disturbances arising from integrated operation with a power generation plant. It is shown that the performance of the absorber is more sensitive to the molar L/G ratio than the actual flow rates of the liquid solvent and flue gas. In addition, the importance of appropriate water balance in the absorber column is shown. A step change of the reboiler duty indicates a slow response. A case involving the combination of two fundamental CO₂ capture technologies (the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing) is studied. The flue gas composition was altered to mimic that observed with the combination. There was an initial sharp decrease in CO₂ absorption level which may not be observed in steady-state simulations.     

Research on mechanism of ammonia escaping and control in the process of CO2 capture using ammonia solution

As CO₂ is the major greenhouse gas, reducing its emission has become an attentive problem in the whole world. It is very important to develop CO₂ capture technology for coal-fired power plants. Using ammonia solution to absorb CO₂ from the flue gas, which is expected to have advantages of low cost, high efficiency and high absorption load, has become an emerging, hot research area in recent years. However, this technology faces a troublesome problem of ammonia escape. This paper analyzes the mechanism of escaping ammonia; it is also shown the main existing methods to control the escape of ammonia. By comparison, it is concluded that controlling the source of ammonia is feasible. It is also shown that adding some organic additives can inhibit the escape of ammonia and enhance the CO₂ removal to some extent at the same time.     

A multi-scale framework for CO2 capture,utilization, and sequestration: CCUS and CCU

We present a multi-scale framework for the optimal design of CO₂ capture, utilization, and sequestration (CCUS) supply chain network to minimize the cost while reducing stationary CO₂ emissions in the United States. We also design a novel CO₂ capture and utilization (CCU) network for economic benefit through utilizing CO₂ for enhanced oil recovery. Both the designs of CCUS and CCU supply chain networks are multi-scale problems which require decision making at material, process and supply chain levels. We present a hierarchical and multi-scale framework to design CCUS and CCU supply chain networks with minimum investment, operating and material costs. While doing so, we take into consideration the selection of source plants, capture processes, capture materials, CO₂ pipelines, locations of utilization and sequestration sites, and amounts of CO₂ storage. Each CO₂ capture process is optimized, and the best materials are screened from large pool of candidate materials. Our optimized CCUS supply chain network can reduce 50% of the total stationary CO₂ emission in the U.S. at a cost of $35.63 per ton of CO₂ captured and managed. The optimum CCU supply chain network can capture and utilize CO₂ to make a total profit of more than 555 million dollars per year ($9.23 per ton). We have also shown that more than 3% of the total stationary CO₂ emissions in the United States can be eliminated through CCU networks at zero net cost. These results highlight both the environmental and economic benefits which can be gained through CCUS and CCU networks. We have designed the CCUS and CCU networks through (i) selecting novel materials and optimized process configurations for CO₂ capture, (ii) simultaneous selection of materials and capture technologies, (iii) CO₂ capture from diverse emission sources, and (iv) CO₂ utilization for enhanced oil recovery. While we demonstrate the CCUS and CCU networks to reduce stationary CO₂ emissions and generate profits in the United States, the proposed framework can be applied to other countries and regions as well.     

Preliminary analysis of process flow sheet modifications for energy efficient CO2 capture from flue gases using chemical absorption

The energy penalty associated with solvent based capture of CO₂ from power station flue gases can be reduced by incorporating process flow sheet modifications into the standard process. A review of modifications suggested in the open and patent literature identified several options, primarily intended for use in the gas processing industry. It was not immediately clear whether these options would have the same benefits when applied to CO₂ capture from near atmospheric pressure combustion flue gases. Process flow sheet modifications, including split flow, rich split, vapour recompression, and inter-stage cooling, were therefore modelled using a commercial rate-based simulation package. The models were completed for a Queensland (Australia) based pilot plant running on 30% MEA as the solvent. The preliminary modelling results showed considerable benefits in reducing the energy penalty of capturing CO₂ from combustion flue gases. Further work will focus on optimising and validating the most relevant process flow sheet modifications in a pilot plant.     

CO2 capture by adsorption with nitrogen enriched carbons

The success of CO₂ capture with solid sorbents is dependent on the development of a low cost sorbent with high CO₂ selectivity and adsorption capacity. Immobilised amines are expected to offer the benefits of liquid amines in the typical absorption process, with the added advantages that solids are easy to handle and that they do not give rise to corrosion problems. In this work, different alkylamines were evaluated as a potential source of basic sites for CO₂ capture, and a commercial activated carbon was used as a preliminary support in order to study the effect of the impregnation. The amine coating increased the basicity and nitrogen content of the carbon. However, it drastically reduced the microporous volume of the activated carbon, which is chiefly responsible for CO₂ physisorption, thus decreasing the capacity of raw carbon at room temperature.     

Capital costs and energy considerations of different alternative stripper configurations for post combustion CO2 capture

Capturing and storing the greenhouse gas carbon dioxide produced by power plants and chemical production plants before it is emitted to the atmosphere will play a major role in mitigation climate change. Among the different technologies, aqueous amine absorption/stripping is a promising one. In this study, five different configurations for aqueous absorption/stripping have been compared with regards to capital investment and energy consumption. The process simulations are made with the use of Unisim Design and ProTreat, while for the cost calculations, data from Turton et al. (2009) and Sinnott and Towler (2009) are used.We cannot identify one single configuration to be the optimum always for all situations, as it depends on many parameters like energy and material costs, interest rate, plant complexity, etc. With the assumption and estimated parameters in this study we find that vapor recompression configuration is the best configuration because it has the lowest total capture cost and CO₂ avoided cost. In addition, the plant complexity does not increase very much compared to the benchmark. The split-stream configuration with cooling of semi-lean amine is the second best. However, this configuration increases the investment cost and plant complexity significantly.The effect of heat integration between the compression section and the stripper is also considered. We can reduce heat requirement by heat integration, but since the inlet temperature to the compressors become higher, the compression efficiency will decrease and compression work will increase. In addition, the capital cost and the complexity of the plant will increase. Because of the higher inlet temperature the water content of produced CO₂ is higher and consequently the corrosion problems is more serious in pipes and equipment for compression and injection section.     

On the integration of CO2 capture with coal-fired power plants: A methodology to assess and optimise solvent-based post-combustion capture systems

Amine and other liquid solvent CO₂ capture systems capture have historically been developed in the oil and gas industry with a different emphasis to that expected for fossil fuel power generation with post-combustion capture. These types of units are now being adapted for combustion flue gas scrubbing for which they need to be designed to operate at lower CO₂ removal rates - around 85-90% and to be integrated with CO₂ compression systems. They also need to be operated as part of a complete power plant with the overall objective of turning fuel into low-carbon electricity.The performance optimisation approach for solvents being considered for post-combustion capture in power generation therefore needs to be updated to take into account integration with the power cycle and the compression train. The most appropriate metric for solvent assessment is the overall penalty on electricity output, rather than simply the thermal energy of regeneration of the solvent used.Methodologies to evaluate solvent performance that have been reported in the literature are first reviewed. The results of the model of a steam power cycle integrated with the compression system focusing on key parameters of the post-combustion capture plant - solvent energy of regeneration, solvent regeneration temperature and desorber pressure - are then presented. The model includes a rigorous thermodynamic integration of the heat available in the capture and compression units into the power cycle for a range of different solvents, and shows that the electricity output penalty of steam extraction has a strong dependence on solvent thermal stability and the temperature available for heat recovery. A method is provided for assessing the overall electricity output penalty (EOP), expressed as total kWh of lost output per tonne of CO₂ captured including ancillary power and compression, for likely combinations of these three key post-combustion process parameters. This correlation provides a more representative method for comparing post-combustion capture technology options than the use of single parameters such as solvent heat of regeneration.     

Exergoeconomic and exergoenvironmental evaluation of power plants including CO2 capture

CO₂ capture from power plants, combined with CO₂ storage, is a potential means for limiting the impact of fossil fuel use on the climate. In this paper, three oxy-fuel plants with incorporated CO₂ capture are evaluated from an economic and environmental perspective. The oxy-fuel plants, a plant with chemical looping combustion with near 100% CO₂ capture and two advanced zero emission plants with 100% and 85% CO₂ capture are evaluated and compared to a similarly structured reference plant without CO₂ capture. To complete the comparison, the reference plant is also considered with CO₂ capture incorporating chemical absorption with monoethanolamine. Two exergy-based methods, the exergoeconomic and the exergoenvironmental analyses, are used to determine the cost-related and the environmental impacts of the plants, respectively, and to reveal options for improving their overall effectiveness.For the considered oxy-fuel plants, the investment cost is estimated to be almost double that of the reference plant, mainly due to the equipment used for oxygen production and CO₂ compression. Furthermore, the exergoeconomic analysis reveals an increase in the cost of electricity with respect to the reference plant by more than 20%, with the advanced zero emission plant with 85% CO₂ capture being the most economical choice. On the other hand, a life cycle assessment reveals a decrease in the environmental impact of the plants with CO₂ capture, due to the CO₂ and NO_x emission control. This leads to a reduction in the overall environmental impact of the plants by more than 20% with respect to the reference plant. The most environmentally friendly concept is the plant with chemical looping combustion.     

Post-combustion CO2 capture with chemical absorption: A state-of-the-art review

Global concentration of CO₂ in the atmosphere is increasing rapidly. CO₂ emissions have an impact on global climate change. Effective CO₂ emission abatement strategies such as Carbon Capture and Storage (CCS) are required to combat this trend. There are three major approaches for CCS: post-combustion capture, pre-combustion capture and oxyfuel process. Post-combustion capture offers some advantages as existing combustion technologies can still be used without radical changes on them. This makes post-combustion capture easier to implement as a retrofit option (to existing power plants) compared to the other two approaches. Therefore, post-combustion capture is probably the first technology that will be deployed. This paper aims to provide a state-of-the-art assessment of the research work carried out so far in post-combustion capture with chemical absorption. The technology will be introduced first, followed by required preparation of flue gas from power plants to use this technology. The important research programmes worldwide and the experimental studies based on pilot plants will be reviewed. This is followed by an overview of various studies based on modelling and simulation. Then the focus is turned to review development of different solvents and process intensification. Based on these, we try to predict challenges and potential new developments from different aspects such as new solvents, pilot plants, process heat integration (to improve efficiency), modelling and simulation, process intensification and government policy impact.