Mitigation of NOx emissions from a jatropha biodiesel fuelled DI diesel engine using antioxidant additives

Biodiesel offers cleaner combustion over conventional diesel fuel including reduced particulate matter, carbon monoxide and unburned hydrocarbon emissions. However, several studies point to slight increase in NO_x emissions (about 10%) for biodiesel fuel compared with conventional diesel fuel. Use of antioxidant additives is one of the most cost-effective ways to mitigate the formation of prompt NO_x. In this study, the effect of antioxidant additives on NO_x emissions in a jatropha methyl ester fuelled direct injection diesel engine have been investigated experimentally and compared. A survey of literature regarding the causes of biodiesel NO_x effect and control strategies is presented. The antioxidant additives L-ascorbic acid, α tocopherol acetate, butylated hydroxytoluene, p-phenylenediamine and ethylenediamine were tested on computerised Kirloskar-make 4 stroke water cooled single cylinder diesel engine of 4.4 kW rated power. Results showed that antioxidants considered in the present study are effective in controlling the NO_x emissions of biodiesel fuelled diesel engines. A 0.025%-m concentration of p-phenylenediamine additive was optimal as NO_x levels were substantially reduced in the whole load range in comparison with neat biodiesel. However, hydrocarbon and CO emissions were found to have increased by the addition of antioxidants.     

Attempts to reduce NOx exhaust emissions by using reformulated biodiesel

Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from diesel engines. Under some conditions, however, biodiesel produced from certain feedstocks has been shown to cause an increase in nitrogen oxides (NO_x). This is of special concern in urban areas that are subject to strict environmental regulations. Although soy-based biodiesel may increase the emission of nitrogen oxides, it is the most easily accessible in North America. We investigated two routes to reformulate soy-based biodiesel in an effort to reduce nitrogen oxide emissions. In one of these, soy-oil methyl esters were modified by conversion of a proportion of the cis bonds in the fatty acid chains of its methyl esters to their trans isomers. In the other approach, polyol derivatives of soybean oil were transesterified to form soy methyl polyol fatty acid esters. The NO_x emissions of these modified biodiesels were then examined, using a Yanmar L100 single cylinder, four stroke, naturally aspirated, air cooled, direct injection diesel engine. Using either isomerized methyl oleate or isomerized soy biodiesel, at 20% blend level in petroleum diesel (‘B20’), nitrogen oxide emissions were elevated by between 1.5 and 3 percentage points relative to the combustion of a B20 blend of commercial biodiesel. Nitrogen oxide emissions were reduced in proportion to blend level during the combustion of polyol biodiesel, with a 20% blend in petrodiesel resulting in a reduction of about 4.5 percentage points relative to the emissions of a comparable blend of commercial soy biodiesel.     

Effects of NOx-inhibitor agent on fuel properties of three-phase biodiesel emulsions

Biodiesel is one of the more promising alternative clean fuels to fossil fuel, which can reduce the emissions of fossil fuel burning, and possibly resolve the energy crisis caused by the exhaustion of petroleum resources in the near future. The burning of biodiesel emits much less gaseous emissions and particulate matter primarily because of its dominant combustion efficiency. However, the high oxygen content in biodiesel not only promotes the burning process but also enhances NO_x formation when biodiesel is used as fuel. Biodiesel emulsion and the additive of NO_x-inhibitor agent are considered to reduce levels of NO_x emissions in this experimental study. The biodiesel was produced by transesterification reaction accompanied with peroxidation process. A three-phase biodiesel emulsion of oil-in water drops-in oil (O/W/O) and an O/W/O biodiesel emulsion containing aqueous ammonia were prepared afterwards. The effect of the existence of NO_x-inhibitor agent on the fuel properties and the emulsion characteristics of the O/W/O biodiesel emulsions were investigated. The experimental results show that the burning of the O/W/O biodiesel emulsion and the O/W/O biodiesel emulsion containing aqueous ammonia had larger fraction of fuel burnt and thus larger heat release than the neat biodiesel if water content is not considered for the calculation of heating value. The addition of aqueous ammonia within the dispersed phase of the O/W/O biodiesel emulsion appeared to deteriorate the emulsification characteristics. A smaller quantity of emulsion and greater kinematic viscosity were formed while a larger carbon residue and actual reaction-heat release also appeared for this O/W/O biodiesel emulsion. Aqueous ammonia in the O/W/O biodiesel emulsion produces a higher pH value as well. In addition, the number as well as the volumetric fraction of the dispersed water droplets is reduced for the O/W/O biodiesel emulsion that contains aqueous ammonia.     

Adiabatic flame temperature from biofuels and fossil fuels and derived effect on NOx emissions

There is currently a sustained interest in biofuels as they represent a potential alternative to petroleum derived fuels. Biofuels are likely to help decrease greenhouse gas emissions and the dependence on oil resources. Biodiesels are Fatty Acid Methyl Esters (FAMEs) that are mainly derived from vegetable oils; their compositions depend on the parent vegetables: rapeseed (“RME”), soybean (“SME”), sunflower, palm etc. A fraction of biodiesel has also an animal origin (“tallow”). A key factor for the use of biofuels in gas turbines is their emission indices (NOx, CO, VOC, and PM) in comparison with those of conventional “petroleum gasoils”. While biodiesels reduce carbon-containing pollutants, experimental data from diesel engines show a slight increase in NOx. The literature relating to gas turbines is very scarce. Two recent, independent field tests carried out in Europe (RME) and in the USA (SME) showed slightly lower NOx while a lab test on a microturbine showed the opposite effect. To clarify the NOx index of biodiesels in gas turbines, a study has been undertaken, taking gasoil and natural gas (NG) as reference fuels. In this study, a calculation of the flame temperature developed by the 3 classes of fuels has been performed and the effect of their respective compositions has been investigated. The five FAMEs studied were RME, SME and methyl esters of sunflower, palm and tallow; these are representative of most widespread vegetable and animal oil bases worldwide. The software THERGAS has been used to calculate the enthalpy and free energy properties of the fuels and GASEQ for the flame temperature (T_f), acknowledging the fact that “thermal NOx” represents the predominant form of NOx in gas turbines. To complete the approach to structural effects, we have modeled two NG compositions (rich and weak gases) and three types of gasoil using variable blends of eleven linear/branched/cyclic molecules. The results are consistent with the two recent field tests and show that the FAMEs lie close to petroleum gasoils and higher than NG in terms of NOx emission. The composition of the biodiesel and regular diesel fuel influences their combustion heat: methyl esters with double bonds see a slight increase of their T_f and their NOx index while that of gasoil is sensitive to the aromatic content.     

Multi response optimization of NOx emission of a stationary diesel engine

In the present work the combined effect of fuel injection timing, percentage of EGR and fuel injection pressure in controlling the NO_x emission of a stationary diesel engine fuelled with diesel was investigated. Three levels were chosen in each factor and NO_x emission, smoke concentration and brake fuel conversion efficiency are taken as the response variables. Experiments were designed as per Taguchi’s L₉ orthogonal array and tests were conducted with different injection timings, percentage EGR (by volume) and injection pressures. Multi response signal to noise ratio (MRSN) was calculated for the response variables and the optimum combination level of factors was obtained simultaneously using Taguchi’s parametric design. Obtained combination was confirmed experimentally and significant improvement was observed in the response variables.     

Engine performance and emission characteristics of a three-phase emulsion of biodiesel produced by peroxidation

Biodiesel, which is produced from vegetable oils, animal fats or used cooking oils, can be used as an alternative fuel for diesel engines. The high oxygen content of biodiesel not only enhances its burning efficiency, but also generally promotes the formation of more nitrogen oxides (NO_x) during the burning process. Fuel emulsification and the use of NO_x inhibitor agents in fuel are considered to be effective in reducing NO_x emissions. In the study reported herein, soybean oil was used as raw oil to produce biodiesel by transesterification reaction accompanied by peroxidation to further improve the fuel properties of the biodiesel, which was water washed and distilled to remove un-reacted methanol, water, and other impurities. The biodiesel product was then emulsified with distilled water and emulsifying surfactant by a high-speed mechanical homogenizer to produce a three-phase oil-droplets-in-water-droplets-in-oil (i.e. O/W/O) biodiesel emulsion and an O/W/O emulsion that contained aqueous ammonia, which is a NO_x inhibitor agent. A four-stroke diesel engine, in combination with an eddy-current dynamometer, was used to investigate the engine performance and emission characteristics of the biodiesel, the O/W/O biodiesel emulsion, the O/W/O biodiesel emulsion that contained aqueous ammonia, and ASTM No. 2D diesel. The experimental results show that the O/W/O emulsion has the lowest carbon dioxide (CO₂) emissions, exhaust gas temperature, and heating value, and the largest brake specific fuel consumption, fuel consumption rate, and kinematic viscosity of the four tested fuels. The increase of engine speed causes the increase of equivalence ratio, exhaust gas temperature, CO₂ emissions, fuel consumption rate, and brake specific fuel consumption, but a decrease of NO_x emissions. Moreover, the existence of aqueous ammonia in the O/W/O biodiesel emulsion curtails NO_x formation, thus resulting in the lowest NO_x emissions among the four tested fuels in burning the O/W/O biodiesel emulsion that contained aqueous ammonia.     

Application of the thermal DeNOx process to diesel engine DeNOx: an experimental and kinetic modelling study

Diesel DeNO_x experiments have been conducted using the selective noncatalytic ‘thermal DeNO_x’ process in a diesel fuelled combustion-driven flow reactor which simulated a single cylinder (966 cm³) and head equipped with a water-cooling jacket and an exhaust pipe. NH₃ was directly injected into the cylinder to reduce NO_x emissions. A wide range of air/fuel ratios (A/F=20-40) was selected for NO_x reduction where an initial NO_x of 530 ppm was usually maintained with a molar ratio (β=NH₃/NO_x) of 1.5.The results indicate that a 34% NO_x reduction can be achieved from the cylinder injection in the temperature range, 1100-1350 K. Most of the NO_x reduction occurs within the cylinder and head section (residence time<40 ms), since temperatures in the exhaust are too low for additional NO_x reduction. Under large gas quenching rates, increasing β values (e.g. 4.0) substantially increase the NO_x reduction up to 60%, which is comparable with those achieved under isothermal conditions. Experimental findings are analysed by chemical kinetics using the Miller and Bowman mechanism including both N/H/O species and CO/hydrocarbon reactions to account for CO/UHC oxidation effects, based on practical nonisothermal conditions. Comparisons of the kinetic calculations with the experimental data are given as regards temperature characteristics, residence time and molar ratio. In addition, the effects of CO/UHC and branching ratio (α=k₁/(k₁+k₂)) for the reaction NH₂+NO=products are discussed in terms of NO reduction features, together with practical implications.     

Evaluation of formulation strategies to eliminate the biodiesel NOx effect

In this paper, we explore the efficacy of (1) reducing the iodine value of soy-derived biodiesel fuels through increasing the methyl oleate (methyl ester of oleic acid) content and (2) addition of cetane improvers, as strategies to combat the biodiesel NO_x effect: the increase in NO_x emissions observed in most studies of biodiesel and biodiesel blends. This is accomplished by spiking a conventional soy-derived biodiesel fuel with methyl oleate or with cetane improver. The impact on bulk modulus of compressibility, fuel injection timing, cetane number, combustion, and emissions were examined. The conventional B20 blend produced a NO_x increase of 3–5% relative to petroleum diesel, depending on injection timing. However, by using a B20 blend where the biodiesel portion contained 76% methyl oleate, the biodiesel NO_x effect was eliminated and a NO_x neutral blend was produced. The bulk modulus of petroleum diesel was measured to be 2% lower than B20, yielding a shift in fuel injection timing of 0.1–0.3 crank angle. The bulk modulus of the high methyl oleate B20 blend was measured to be 0.5% lower than B20, not enough to have a measurable impact on fuel injection timing. Increasing the methyl oleate portion of the biodiesel to 76% also had the effect of increasing the cetane number from 48.2 for conventional B20 to 50.4, but this effect is small compared to the increase to 53.5 achieved by adding 1000 ppm of 2-ethylhexyl nitrate (EHN) to B20. For the particular engine tested, NO_x emissions were found to be insensitive to ignition delay, maximum cylinder temperature, and maximum rate of heat release. The dominant effect on NO_x emissions was the timing of the combustion process, initiated by the start of injection, and propagated through the timing of maximum heat release rate and maximum temperature.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Comparison of particle emissions from an engine operating on biodiesel and petroleum diesel

Biodiesel is an alternative fuel with growing usage in the transportation sector. To compare biodiesel and petroleum diesel effects on particle emissions, engine dynamometer tests were performed on a Euro II engine with three test fuels: petroleum diesel (D), biodiesel made from soy bean oil (BS) and biodiesel made from waste cooking oil (BW). PM_2.5 samples were collected on Teflon and quartz filters with a Model 130 High-Flow Impactor (MSP Corp). Organic (OC) and elemental (EC) carbon fractions of PM_2.5 were quantified by a thermal-optical reflectance analysis method and particle size distributions were measured with an electrical low pressure impactor (ELPI). In addition, the gaseous pollutants were measured by an AMA4000 (AVL Corp). The biodiesels were found to produce 19-37% less and 23-133% more PM_2.5 compared to the petroleum diesel at higher and lower engine loads respectively. On the basis of the carbon analysis results, the biodiesel application increased the PM_2.5 OC emissions by 12-190% and decreased the PM_2.5 EC emissions by 53-80%, depending on the fuel and engine operation parameters. Therefore OC/EC was increased by three to eight times with biodiesel application. The geometrical mean diameter of particles from biodiesels and petroleum diesel had consistent trends with load and speed transition. In all the conditions, there is a shift of the particles towards smaller geometric mean diameter for the biodiesel made from waste oil.     

Performance and exhaust emissions in the use of biodiesel in outboard diesel engines

The objective of this study is to compare the engine performance and emission results of biodiesel derived from used cooking oil when applied in different proportions in outboard engines. Results revealed that the use of biodiesel resulted in lower emissions of CO (up to 12%) with an increase in emissions of NO_x (up to 20%, except in one case which presented a slight reduction). Biodiesel also presented a slight increase in specific fuel consumption (lower than 11.4%) which may be acceptable considering the reduction in exhaust emissions. The experimental results proved that biodiesel alone or blended biodiesel can be used in compression ignition outboard engines, thereby providing a viable alternative to diesel. Special attention should be paid to the use of biodiesel in boats operating on lakes and rivers and in sheltered bays, which are more vulnerable to pollution.     

Process optimization for biodiesel production from Jatropha, Karanja and Polanga oils

Petroleum sourced fuels is now widely known as non-renewable due to fossil fuel depletion and environmental degradation. Renewable, carbon neutral, transport fuels are necessary for environmental and economic sustainability. Biodiesel derived from oil crops is a potential renewable and carbon neutral alternative to petroleum fuels. Chemically, biodiesel is monoalkyl esters of long chain fatty acids derived from renewable feed stock like vegetable oils and animal fats. It is produced by transesterification in which, oil or fat is reacted with a monohydric alcohol in presence of a catalyst. The process of transesterification is affected by the mode of reaction condition, molar ratio of alcohol to oil, type of alcohol, type and amount of catalysts, reaction time and temperature and purity of reactants. In the present paper various methods of preparation of biodiesel from non-edible filtered Jatropha (Jatropha curcas), Karanja (Pongamia pinnata) and Polanga (Calophyllum inophyllum) oil have been described. Mono esters (biodiesel) produced and blended with diesel were evaluated. The technical tools and processes for monitoring the transesterification reactions like TLC, GC and HPLC have also been used.     

Biodiesel combustion,emissions and emission control

The use of biodiesel is rapidly expanding around the world, making it imperative to fully understand the impacts of biodiesel on the diesel combustion process, pollutant formation and exhaust aftertreatment. Because its physical properties and chemical composition are distinctly different from conventional diesel fuel, biodiesel can alter the fuel injection and ignition processes whether neat or in blends. As a consequence, the emissions of NO_x and the amount, character and composition of particulate emissions are significantly affected. In this paper, we survey observations from a spectrum of our earlier studies on the impact of biodiesel on diesel combustion, emissions and emission control to provide a summary of the challenges and opportunities that biodiesel can provide.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.     

Numerical investigation on the flow, combustion and NOx emission characteristics in a 500 MWe tangentially fired pulverized-coal boiler

The characteristics of the flow, combustion, temperature and NO_x emissions in a 500 MW_e tangentially fired pulverized-coal boiler are numerically studied using comprehensive models, with emphasis on fuel and thermal NO_x formations. The comparison between the measured values and predicted results shows good agreement, which implies that the adopted combustion and NO_x formation models are suitable for correctly predicting characteristics of the boiler. The relations among the predicted temperature, O₂ and CO₂ mass fractions are discussed based on the calculated distributions. The predicted results clearly show that NO_x formation within the boiler highly depends on the combustion processes as well as the temperature and species concentrations. The results obtained from this study have shown that overfire air (OFA) operation is an efficient way to reduce the NO_x emissions of the pulverized-coal fired boiler. Air staging combustion technology (OFA operation) adopted in this boiler has helped reduce fuel NO_x formation as well as thermal NO_x formation under the present simulated conditions. The decrease in the formation of fuel NO_x is due to the decreased contact of the nitrogen from the fuel with the oxygen within the combustion air, while the decrease in thermal NO_x formation is caused by a decrease in temperature. The detailed results presented in this paper may enhance the understanding of complex flow patterns, combustion processes and NO_x emissions in tangentially fired pulverized-coal boilers, and may also provide a useful basis for NO_x reduction and control.     

Comparison of emissions of a direct injection diesel engine operating on biodiesel with emulsified and fumigated methanol

Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NO_x) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO₂, NO_x, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal efficiency at low engine load while the fumigation mode gives slightly higher brake thermal efficiency at medium and high engine loads. In the fumigation mode, an extra fuel injection control system is required, and there is also an increase in CO, HC and NO₂ (nitrogen dioxide) and particulate emissions in the engine exhaust, which are disadvantages compared with the blended mode.     

The potential of di-methyl ether (DME) as an alternative fuel for compression-ignition engines: A review

This paper reviews the properties and application of di-methyl ether (DME) as a candidate fuel for compression-ignition engines. DME is produced by the conversion of various feedstock such as natural gas, coal, oil residues and bio-mass. To determine the technical feasibility of DME, the review compares its key properties with those of diesel fuel that are relevant to this application. DME’s diesel engine-compatible properties are its high cetane number and low auto-ignition temperature. In addition, its simple chemical structure and high oxygen content result in soot-free combustion in engines. Fuel injection of DME can be achieved through both conventional mechanical and current common-rail systems but requires slight modification of the standard system to prevent corrosion and overcome low lubricity. The spray characteristics of DME enable its application to compression-ignition engines despite some differences in its properties such as easier evaporation and lower density. Overall, the low particulate matter production of DME provides adequate justification for its consideration as a candidate fuel in compression-ignition engines. Recent research and development shows comparable output performance to a diesel fuel led engine but with lower particulate emissions. NO_x emissions from DME-fuelled engines can meet future regulations with high exhaust gas recirculation in combination with a lean NO_x trap. Although more development work has focused on medium or heavy-duty engines, this paper provides a comprehensive review of the technical feasibility of DME as a candidate fuel for environmentally-friendly compression-ignition engines independent of size or application.     

Diesel engine performance and emission characteristics of biodiesel produced by the peroxidation process

Biodiesel is an alternative fuel that is cleaner than petrodiesel. Biodiesel can be used directly as fuel for a diesel engine without having to modify the engine system. It has the major advantages of having high biodegradability, excellent lubricity and no sulfur content. In this study, the biodiesel produced by a transesterification technique was further reacted by using a peroxidation process. Four types of diesel fuel, biodiesel with and without an additional peroxidation process, a commercial biodiesel and ASTM No. 2D diesel were compared for their fuel properties, engine performance and emission characteristics. The experimental results show that the fuel consumption rate, brake thermal efficiency, equivalence ratio, and exhaust gas temperature increased while the bsfc, emission indices of CO₂, CO and NO_x decreased with an increase of engine speed. The three biodiesels showed a higher fuel consumption rate, bsfc, and brake thermal efficiency, while at the same time exhibited lower emission indices of CO and CO₂ as well as a lower exhaust gas temperature when compared to ASTM No. 2D diesel. Moreover, the biodiesel produced with the additional peroxidation process was found to have an oxygen content, weight proportion of saturated carbon bonds, fuel consumption rate, and bsfc that were higher than the biodiesel produced without the additional process; while at the same time the brake thermal efficiency, equivalence ratio, and emission indices of CO₂, CO and NO_x were found to be lower. In particular, biodiesel produced with the addition of the peroxidation process had the lowest equivalence ratio and emission indices of CO₂, CO and NO_x among all of the four test fuels. Therefore, the peroxidation process can be used to effectively improve the fuel properties and reduce emissions when biodiesel is used.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Experimental measurements of the NOx and CO concentrations operating in oscillatory and non-oscillatory burning conditions

The effects of combustion driven acoustic oscillations in carbon monoxide and nitrogen oxides emission rates of a combustor operated with liquefied petroleum gas (LPG) were investigated. Because the fuel does not contain nitrogen, tests were also conducted with ammonia injected in the fuel, in order to study the formation of fuel NO_x. The main conclusions were: (a) the pulsating combustion process is more efficient than the non-pulsating one and (b) the pulsating combustion process generates higher rates of NO_x, with and without ammonia injection, as shown by CO and NO concentrations as function of the O₂ concentration. An increase in the LPG flow rate, keeping constant the air to fuel ratio, increased the acoustic pressure amplitude and the frequency of oscillation. The injection of ammonia had no influence on either pressure amplitude or frequency.