Mitigation of NOx emissions from a jatropha biodiesel fuelled DI diesel engine using antioxidant additives

Biodiesel offers cleaner combustion over conventional diesel fuel including reduced particulate matter, carbon monoxide and unburned hydrocarbon emissions. However, several studies point to slight increase in NO_x emissions (about 10%) for biodiesel fuel compared with conventional diesel fuel. Use of antioxidant additives is one of the most cost-effective ways to mitigate the formation of prompt NO_x. In this study, the effect of antioxidant additives on NO_x emissions in a jatropha methyl ester fuelled direct injection diesel engine have been investigated experimentally and compared. A survey of literature regarding the causes of biodiesel NO_x effect and control strategies is presented. The antioxidant additives L-ascorbic acid, α tocopherol acetate, butylated hydroxytoluene, p-phenylenediamine and ethylenediamine were tested on computerised Kirloskar-make 4 stroke water cooled single cylinder diesel engine of 4.4 kW rated power. Results showed that antioxidants considered in the present study are effective in controlling the NO_x emissions of biodiesel fuelled diesel engines. A 0.025%-m concentration of p-phenylenediamine additive was optimal as NO_x levels were substantially reduced in the whole load range in comparison with neat biodiesel. However, hydrocarbon and CO emissions were found to have increased by the addition of antioxidants.     

Attempts to reduce NOx exhaust emissions by using reformulated biodiesel

Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from diesel engines. Under some conditions, however, biodiesel produced from certain feedstocks has been shown to cause an increase in nitrogen oxides (NO_x). This is of special concern in urban areas that are subject to strict environmental regulations. Although soy-based biodiesel may increase the emission of nitrogen oxides, it is the most easily accessible in North America. We investigated two routes to reformulate soy-based biodiesel in an effort to reduce nitrogen oxide emissions. In one of these, soy-oil methyl esters were modified by conversion of a proportion of the cis bonds in the fatty acid chains of its methyl esters to their trans isomers. In the other approach, polyol derivatives of soybean oil were transesterified to form soy methyl polyol fatty acid esters. The NO_x emissions of these modified biodiesels were then examined, using a Yanmar L100 single cylinder, four stroke, naturally aspirated, air cooled, direct injection diesel engine. Using either isomerized methyl oleate or isomerized soy biodiesel, at 20% blend level in petroleum diesel (‘B20’), nitrogen oxide emissions were elevated by between 1.5 and 3 percentage points relative to the combustion of a B20 blend of commercial biodiesel. Nitrogen oxide emissions were reduced in proportion to blend level during the combustion of polyol biodiesel, with a 20% blend in petrodiesel resulting in a reduction of about 4.5 percentage points relative to the emissions of a comparable blend of commercial soy biodiesel.     

A numerical investigation into the anomalous slight NOx increase when burning biodiesel; A new (old) theory

Biodiesel is a notable alternative to petroleum derived diesel fuel because it comes from natural domestic sources and thus reduces dependence on diminishing petroleum fuel from foreign sources, it likely lowers lifecycle greenhouse gas emissions, and it lowers an engine's emission of most pollutants as compared to petroleum derived diesel. However, the use of biodiesel often slightly increases a diesel engine's emission of smog forming nitrogen oxides (NO_x) relative to petroleum diesel. In this paper, previously proposed theories for this slight NO_x increase are reviewed, including theories based on biodiesel's cetane number, which leads to differing amounts of charge preheating, and theories based on the fuel's bulk modulus, which affects injection timing. This paper proposes an additional theory for the slight NO_x increase of biodiesel. Biodiesel typically contains more double bonded molecules than petroleum derived diesel. These double bonded molecules have a slightly higher adiabatic flame temperature, which leads to the increase in NO_x production for biodiesel. Our theory was verified using numerical simulations to show a NO_x increase, due to the double bonded molecules, that is consistent with observation. Further, the details of these numerical simulations show that NO_x is predominantly due to the Zeldovich mechanism.     

Effects of NOx-inhibitor agent on fuel properties of three-phase biodiesel emulsions

Biodiesel is one of the more promising alternative clean fuels to fossil fuel, which can reduce the emissions of fossil fuel burning, and possibly resolve the energy crisis caused by the exhaustion of petroleum resources in the near future. The burning of biodiesel emits much less gaseous emissions and particulate matter primarily because of its dominant combustion efficiency. However, the high oxygen content in biodiesel not only promotes the burning process but also enhances NO_x formation when biodiesel is used as fuel. Biodiesel emulsion and the additive of NO_x-inhibitor agent are considered to reduce levels of NO_x emissions in this experimental study. The biodiesel was produced by transesterification reaction accompanied with peroxidation process. A three-phase biodiesel emulsion of oil-in water drops-in oil (O/W/O) and an O/W/O biodiesel emulsion containing aqueous ammonia were prepared afterwards. The effect of the existence of NO_x-inhibitor agent on the fuel properties and the emulsion characteristics of the O/W/O biodiesel emulsions were investigated. The experimental results show that the burning of the O/W/O biodiesel emulsion and the O/W/O biodiesel emulsion containing aqueous ammonia had larger fraction of fuel burnt and thus larger heat release than the neat biodiesel if water content is not considered for the calculation of heating value. The addition of aqueous ammonia within the dispersed phase of the O/W/O biodiesel emulsion appeared to deteriorate the emulsification characteristics. A smaller quantity of emulsion and greater kinematic viscosity were formed while a larger carbon residue and actual reaction-heat release also appeared for this O/W/O biodiesel emulsion. Aqueous ammonia in the O/W/O biodiesel emulsion produces a higher pH value as well. In addition, the number as well as the volumetric fraction of the dispersed water droplets is reduced for the O/W/O biodiesel emulsion that contains aqueous ammonia.     

The potential of di-methyl ether (DME) as an alternative fuel for compression-ignition engines: A review

This paper reviews the properties and application of di-methyl ether (DME) as a candidate fuel for compression-ignition engines. DME is produced by the conversion of various feedstock such as natural gas, coal, oil residues and bio-mass. To determine the technical feasibility of DME, the review compares its key properties with those of diesel fuel that are relevant to this application. DME’s diesel engine-compatible properties are its high cetane number and low auto-ignition temperature. In addition, its simple chemical structure and high oxygen content result in soot-free combustion in engines. Fuel injection of DME can be achieved through both conventional mechanical and current common-rail systems but requires slight modification of the standard system to prevent corrosion and overcome low lubricity. The spray characteristics of DME enable its application to compression-ignition engines despite some differences in its properties such as easier evaporation and lower density. Overall, the low particulate matter production of DME provides adequate justification for its consideration as a candidate fuel in compression-ignition engines. Recent research and development shows comparable output performance to a diesel fuel led engine but with lower particulate emissions. NO_x emissions from DME-fuelled engines can meet future regulations with high exhaust gas recirculation in combination with a lean NO_x trap. Although more development work has focused on medium or heavy-duty engines, this paper provides a comprehensive review of the technical feasibility of DME as a candidate fuel for environmentally-friendly compression-ignition engines independent of size or application.     

Effects of dimethyl-ether (DME) spray behavior in the cylinder on the combustion and exhaust emissions characteristics of a high speed diesel engine

The purpose of this study was to analyze the exhaust emissions of DME fuel through experimental and numerical analyses of in-cylinder spray behavior. To investigate this behavior, spray characteristics such as the spray tip penetration, spray cone angle, and spray targeting point were studied in a re-entrant cylinder shape under real combustion chamber conditions. The combustion performance and exhaust emissions of the DME-fueled diesel engine were calculated using KIVA-3V. The numerical results were validated with experimental results from a DME direct injection compression ignition engine with a single cylinder.The combustion pressure and IMEP have their peak values at an injection timing of around BTDC 30°, and the peak combustion temperature, exhaust emissions (soot, NO_x), and ISFC had a lower value. The HC and CO emissions from DME fuel showed lower values and distributions in the range from BTDC 25° to BTDC 10° at which a major part of the injected DME spray was distributed into the piston bowl area. When the injection timing advanced to before BTDC 30°, the HC and CO emissions showed a rapid increase. When the equivalence ratio increased, the combustion pressure and peak combustion temperature decreased, and the peak IMEP was retarded from BTDC 25° to BTDC 20°. In addition, NO_x emissions were largely decreased by the low combustion temperature, but the soot emissions increased slightly.     

Comparison of particle emissions from an engine operating on biodiesel and petroleum diesel

Biodiesel is an alternative fuel with growing usage in the transportation sector. To compare biodiesel and petroleum diesel effects on particle emissions, engine dynamometer tests were performed on a Euro II engine with three test fuels: petroleum diesel (D), biodiesel made from soy bean oil (BS) and biodiesel made from waste cooking oil (BW). PM_2.5 samples were collected on Teflon and quartz filters with a Model 130 High-Flow Impactor (MSP Corp). Organic (OC) and elemental (EC) carbon fractions of PM_2.5 were quantified by a thermal-optical reflectance analysis method and particle size distributions were measured with an electrical low pressure impactor (ELPI). In addition, the gaseous pollutants were measured by an AMA4000 (AVL Corp). The biodiesels were found to produce 19-37% less and 23-133% more PM_2.5 compared to the petroleum diesel at higher and lower engine loads respectively. On the basis of the carbon analysis results, the biodiesel application increased the PM_2.5 OC emissions by 12-190% and decreased the PM_2.5 EC emissions by 53-80%, depending on the fuel and engine operation parameters. Therefore OC/EC was increased by three to eight times with biodiesel application. The geometrical mean diameter of particles from biodiesels and petroleum diesel had consistent trends with load and speed transition. In all the conditions, there is a shift of the particles towards smaller geometric mean diameter for the biodiesel made from waste oil.     

Numerical investigation on the flow, combustion and NOx emission characteristics in a 500 MWe tangentially fired pulverized-coal boiler

The characteristics of the flow, combustion, temperature and NO_x emissions in a 500 MW_e tangentially fired pulverized-coal boiler are numerically studied using comprehensive models, with emphasis on fuel and thermal NO_x formations. The comparison between the measured values and predicted results shows good agreement, which implies that the adopted combustion and NO_x formation models are suitable for correctly predicting characteristics of the boiler. The relations among the predicted temperature, O₂ and CO₂ mass fractions are discussed based on the calculated distributions. The predicted results clearly show that NO_x formation within the boiler highly depends on the combustion processes as well as the temperature and species concentrations. The results obtained from this study have shown that overfire air (OFA) operation is an efficient way to reduce the NO_x emissions of the pulverized-coal fired boiler. Air staging combustion technology (OFA operation) adopted in this boiler has helped reduce fuel NO_x formation as well as thermal NO_x formation under the present simulated conditions. The decrease in the formation of fuel NO_x is due to the decreased contact of the nitrogen from the fuel with the oxygen within the combustion air, while the decrease in thermal NO_x formation is caused by a decrease in temperature. The detailed results presented in this paper may enhance the understanding of complex flow patterns, combustion processes and NO_x emissions in tangentially fired pulverized-coal boilers, and may also provide a useful basis for NO_x reduction and control.     

Combustion, performance and emission characteristics of a DI diesel engine fueled with ethanol-biodiesel blends

In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NO_x and particulate emissions of the diesel engine. The effectiveness of NO_x and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.     

Physical-chemical properties of waste cooking oil biodiesel and castor oil biodiesel blends

This work presents the physical-chemical properties of fuel blends of waste cooking oil biodiesel or castor oil biodiesel with diesel oil. The properties evaluated were fuel density, kinematic viscosity, cetane index, distillation temperatures, and sulfur content, measured according to standard test methods. The results were analyzed based on present specifications for biodiesel fuel in Brazil, Europe, and USA. Fuel density and viscosity were increased with increasing biodiesel concentration, while fuel sulfur content was reduced. Cetane index is decreased with high biodiesel content in diesel oil. The biodiesel blends distillation temperatures T₁₀ and T₅₀ are higher than those of diesel oil, while the distillation temperature T₉₀ is lower. A brief discussion on the possible effects of fuel property variation with biodiesel concentration on engine performance and exhaust emissions is presented. The maximum biodiesel concentration in diesel oil that meets the required characteristics for internal combustion engine application is evaluated, based on the results obtained.     

Biodiesel engine performance and emissions in low temperature combustion

Engine performance and emission comparisons were made between the use of soy, Canola and yellow grease derived B100 biodiesel fuels and an ultra-low sulphur diesel fuel in the high load engine operating conditions. Compared to the diesel fuel engine-out emissions of nitrogen oxides (NO_x), a high-cetane number (CN) biodiesel fuel produced comparable NO_x while the biodiesel with a CN similar to the diesel fuel produced relatively higher NO_x at a fixed start of injection. The soot, carbon monoxide and un-burnt hydrocarbon emissions were generally lower for the biodiesel-fuelled engine. Exhaust gas recirculation (EGR) was then extensively applied to initiate low temperature combustion (LTC) mode at medium and low load conditions. An intake throttling valve was implemented to increase the differential pressure between the intake and exhaust in order to increase and enhance the EGR. Simultaneous reduction of NO_x and soot was achieved when the ignition delay was prolonged by more than 50% from the case with 0% EGR at low load conditions. Furthermore, a preliminary ignition delay correlation under the influence of EGR at steady-state conditions was developed. The correlation considered the fuel CN and oxygen concentrations in the intake air and fuel. The research intends to achieve simultaneous reductions of NO_x and soot emissions in modern production diesel engines when biodiesel is applied.     

Calculation of mass emissions, oxygen mass fraction and thermal capacity of the inducted charge in SI and diesel engines from exhaust and intake gas analysis

New computational procedures are proposed for experimentally evaluating air-fuel ratio and mass fractions of exhaust emissions as well as EGR rate, oxygen mass fraction and thermal capacity of the inducted charge in IC engines running with diesel oil, gasoline or any alternative liquid or gaseous fuel, such as LPG or CNG. Starting from the chemical reaction of fuel with air, from gaseous and smoke level measurements in the raw gases, the procedures calculate the volume fractions of oxygen in the combustion air and of compounds in the exhaust gases, including those that are not usually measured, such as water, nitrogen and hydrogen. The methods also take the effects of various fuel and combustion air compositions into account, as well as to the presence of water vapor, CO₂, Ar and He in the combustion air.The algorithms are applied to four different automotive engines under wide ranges of steady-state operating conditions: three turbocharged diesel engines featuring high-pressure cooled EGR systems, and an SI naturally aspirated bi-fuel engine running on either gasoline or CNG. The computed air-fuel ratios are compared to those obtained from directly measured air and fuel mass-flow rates as well as from more conventional UEGO sensor data. The mass emissions are worked out in terms of both brake specific mass emissions and emission indexes of each pollutant species, and the results are compared to those obtained by applying SAE and ISO recommended practices. The computed oxygen mass fraction of the inducted charge was then compared to that derived from direct measurement of O₂ concentration in inlet manifold. Finally, the sensitivity of results to the main engine working parameters, the influence of environmental conditions (in particular the effect of air humidity on NO_x formation) and the experimental uncertainties are determined.     

The application of FLOX/COSTAIR technologies to reduce NOx emissions from coal/biomass fired power plant: A technical assessment based on computational simulation

Nitrogen oxides (NO_x) is one of the harmful emissions from power plants. Efforts are made to reduce NO_x emissions by researchers and engineers all the times. NO_x emissions are from three resources during the combustion: prompt NO, fuel NO and thermal NO. The last one - thermal NO, which is described by ‘Zeldovich-mechanism’, is the main source for NO_x emissions. The thermal NO emission mainly results from the high combustion temperature in the combustion process. In order to control the NO formation, the control of peak combustion temperature is the key factor, as well as the oxygen concentration in the combustion areas. Flameless oxidation (FLOX) and continuous staged air combustion (COSTAIR) are two relatively new technologies to control the combustion temperature and the reaction rate and consequently to control the NO_x emissions.In this study both FLOX and COSTAIR technologies are assessed based on a 12 MW_e, coal-fired, circulating fluidised bed combustion (CFBC) power plant by using ECLIPSE simulation software, together with a circulating fluidised bed gasification (CFBG) plus normal burner plant. Two different fuels - coal and biomass (straw) are used for the simulation. The technical results from the study show that the application of FLOX technology to the plant may reduce NO_x emissions by 90% and the application of COSTAIR technology can reduce NO_x emissions by 80-85% from the power plant. The emissions from the straw-fuelled plants are all lower than that of coal-fuelled ones although with less plant efficiencies.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Various strategies for reducing Nox emissions of biodiesel fuel used in conventional diesel engines: A review

Energy demand, decreasing fossil fuel reserves, and health-related issues about pollutants have led researchers to search for renewable alternative fuels to either partially or fully replace fossil fuels. Among many alternative fuels, biodiesel became one of the most popular choices due to similar properties to that of conventional diesel. Biodiesel produces slightly lower brake thermal efficiency compared to that of conventional biodiesel, but has an advantage of reduced emissions of CO₂, CO, HC, and smoke. However, biodiesel shows higher NOx emission which, when used in increased biodiesel market, may become a serious problem. Various strategies were attempted by different researcher to reduce NOx emissions. In this paper, various strategies, adapted for reducing NOx emissions of biodiesel fuel used in diesel engines for automobile applications, are reviewed and discussed. The strategies are grouped into three major groups, namely combustion treatments, exhaust after-treatments, and fuel treatments. Among various strategies discussed, fuel treatments, such as low temperature combustion, mixing fuel additives and reformulating fuel composition, reduce NOx emission without compromising other emission and performance characteristics and they seem to be promising for future biodiesel fuel.     

Biodiesel CO2 emissions: A comparison with the main fuels in the Brazilian market

The use of biodiesel is increasing as an attractive fuel due to the depleting fossil fuel resources and environmental degradation. This paper presents results of an investigation on the potentials of biodiesel as an alternative fuel and main substitute of diesel oil, comparing the CO₂ emissions of the main fuels in the Brazilian market with those of biodiesel, in pure form or blended in different proportions with diesel oil (2%, 5%, and 20%, called B2, B5, and B20, respectively). The results of the study are shown in ton CO₂ per m³ and ton CO₂ per year of fuel. The fuels were analyzed considering their chemical composition, stoichiometric combustion parameters and mean consumption for a single vehicle. The fuels studied were: gasoline, diesel oil, anhydrous ethyl alcohol (anhydrous ethanol), and biodiesel from used frying oil and from soybean oil. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. With data provided by the Brazilian Association of Automotive Vehicle Manufacturers (ANFAVEA) for the number of vehicles produced in Brazil, the emissions of CO₂ for the national fleet in 2007 were obtained per type of fuel. With data provided by the Brazilian Department of Transit (DENATRAN) concerning the number of diesel vehicles in the last five years in Brazil, the total CO₂ emissions and the percentage that they would decrease in the case of use of pure biodiesel, B100, or several mixtures, B2, B5 and B20, were calculated. Estimates of CO₂ emissions for a future scenario considering the mixtures B5 and B20 are also included in this article.     

Sensitivity of Diesel Particulate Material Emissions and Composition to Blends of Petroleum Diesel and Biodiesel Fuel

A number of investigations have examined the impact of the use of biodiesel on the emissions of carbon dioxide and regulated emissions, but limited information exists on the chemical composition of particulate matter from diesel engines burning biodiesel blends. This study examines the composition of diesel particulate matter (DPM) emissions from a commercial agriculture tractor burning a range of biodiesel blends operating under a load that is controlled by a power take off (PTO) dynamometer. Ultra-low sulfur diesel (ULSD) fuel was blended with soybean and beef tallow based biodiesel to examine fuels containing 0% (B0), 25% (B25), 50% (B50), 75% (B75), and 100% (B100) biodiesel. Samples were then collected using a dilution source sampler to simulate atmospheric dilution. Diluted and aged exhaust was analyzed for particle mass and size distribution, PM_2.5 particle mass, PM_2.5 organic and elemental carbon, and speciated organic compounds. PM_2.5 mass emissions rates for the B25, B50, and B75 soybean oil biodiesel mixtures had 20%–30% lower emissions than the petroleum diesel, but B100 emissions were about 40% higher than the petroleum diesel. The trends in mass emission rates with the increasing biodiesel content can be explained by a significant decrease in elemental carbon (EC) emissions across all blending ranges and increasing organic carbon (OC) emissions with pure biodiesel. Beef tallow biodiesel blends showed similar trends. Nevertheless, it is important to note that the study measurements are based on low dilution rates and the OC emissions changes may be affected by ambient temperature and different dilution conditions spanning micro-environments and atmospheric conditions. The results show that the use of biodiesel fuel for economic or climate change mitigation purposes can lead to reductions in PM emissions and a co-benefit of EC emission reductions. Detailed speciation of the OC emissions were also examined and are presented to understand the sensitivity of OC emissions with respect to biodiesel fuel blends.

Copyright 2012 American Association for Aerosol Research     

NOx and SOx emissions of a high sulfur self-retention coal during air-staged combustion

NO_x and SO_x emissions of air-staged combustion were investigated in a 1 MW tangentially-fired furnace combusting a high sulfur self-retention coal. Two variables including the air stoichiometric ratio of primary combustion zone and the relative location of over-fire air (OFA) injection ports were studied. These results suggest that NO_x reduction efficiency monotonically increases with increasing the relative location of OFA injection ports, and the lowest NO_x emissions are achieved when the air stoichiometric ratio of primary combustion zone is 0.85. In the meantime, SO_x emissions can be effectively reduced when the air stoichiometric ratio of primary combustion zone is 0.85 or 0.95, and SO_x emissions monotonically decrease with increasing the relative location of OFA injection ports.     

Evaluation of formulation strategies to eliminate the biodiesel NOx effect

In this paper, we explore the efficacy of (1) reducing the iodine value of soy-derived biodiesel fuels through increasing the methyl oleate (methyl ester of oleic acid) content and (2) addition of cetane improvers, as strategies to combat the biodiesel NO_x effect: the increase in NO_x emissions observed in most studies of biodiesel and biodiesel blends. This is accomplished by spiking a conventional soy-derived biodiesel fuel with methyl oleate or with cetane improver. The impact on bulk modulus of compressibility, fuel injection timing, cetane number, combustion, and emissions were examined. The conventional B20 blend produced a NO_x increase of 3–5% relative to petroleum diesel, depending on injection timing. However, by using a B20 blend where the biodiesel portion contained 76% methyl oleate, the biodiesel NO_x effect was eliminated and a NO_x neutral blend was produced. The bulk modulus of petroleum diesel was measured to be 2% lower than B20, yielding a shift in fuel injection timing of 0.1–0.3 crank angle. The bulk modulus of the high methyl oleate B20 blend was measured to be 0.5% lower than B20, not enough to have a measurable impact on fuel injection timing. Increasing the methyl oleate portion of the biodiesel to 76% also had the effect of increasing the cetane number from 48.2 for conventional B20 to 50.4, but this effect is small compared to the increase to 53.5 achieved by adding 1000 ppm of 2-ethylhexyl nitrate (EHN) to B20. For the particular engine tested, NO_x emissions were found to be insensitive to ignition delay, maximum cylinder temperature, and maximum rate of heat release. The dominant effect on NO_x emissions was the timing of the combustion process, initiated by the start of injection, and propagated through the timing of maximum heat release rate and maximum temperature.     

Biodiesel combustion in an optical HSDI diesel engine under low load premixed combustion conditions

An optically accessible single-cylinder high-speed direct-injection (HSDI) diesel engine was used to investigate the spray and combustion processes for biodiesel blends under different injection strategies. The experimental results indicated that the heat release rate was dominated by a premixed combustion pattern and the heat release rate peak became smaller with injection timing retardation. The ignition and heat release rate peak occurred later with increasing biodiesel content. Fuel impingement on the wall was observed for all test conditions. The liquid penetration became longer and the fuel impingement was stronger with the increase of biodiesel content. Early and late injection timings result in lower flame luminosity due to improved mixing with longer ignition delay. For all the injection timings, lower soot luminosity was seen for biodiesel blends than pure diesel fuel. Furthermore, NO_x emissions were dramatically reduced for premixed combustion mode with retarded post-TDC injection strategies.