Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Transesterification of palm oil on KyMg1 − xZn1 + xO3 catalyst: Effect of Mg-Zn interaction

The Mg-Zn interaction effect of K_yMg_1 − xZn_1 + xO₃ heterogeneous type catalyst and its performance on transesterification of palm oil have been studied using the response surface methodology and the factorial design of experiments. The catalyst was synthesized using the co-precipitation method and the activity was assessed by transesterification of palm oil into fatty acid methyl esters. The ratio of the Mg/Zn metal interaction, temperature and time of calcination were found to have positive influence on the conversion of palm oil to fatty acid methyl ester (FAME) with the effect of metal to metal ratio and temperature of calcination being more significant. The catalytic activity was found to decrease at higher calcination temperature and the catalyst type K₂Mg_0.34Zn_1.66O₃ with Mg/Zn ratio of 4.81 gave FAME content of 73% at a catalyst loading of 1.404 wt.% of oil with molar ratio of methanol to oil being 6:1 at temperature of 150 °C in 6 h. A regression model was obtained to predict conversions to methyl esters as a function of metal interaction ratio, temperature of calcination and time. The observed activity of the synthesized catalyst was due to its synergetic structure and composition.     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Influence of preparation conditions to structure property, NOx and SO2 sorption behavior of the BaFeO3 − x perovskite catalyst

A series of the BaFeO_3 − x perovskite catalysts was synthesized by a sol-gel method using citric acid and/or EDTA as complexants with a purpose to improve their sulfur-resistance by forming a uniform perovskite structure at a low calcination temperature, i.e. 750 °C. The thermogravimetry results show that almost no carbonate was formed after calcination of the xerogel precursor with the complexants' molar ratio of CA/EDTA ≤ 1.5, which was convinced by the in situ DRIFT spectra results of the Ba-Fe-1 catalyst during the SO₂/O₂ sorption. It indicates that, after adding EDTA into the complexants, the metal ions of the raw material could be mixed homogeneously and react stoichiometrically by calcination at 750 °C to form a uniform perovskite structure. Accordingly, the obtained Ba-Fe-1 perovskite presented a performed sulfur-resistance. Moreover, the seriously damaged structure of the BaFeO_3 − x perovskite by reduction could be in situ regenerated by calcination under lean conditions at 400 °C, which is within the operating temperature zone of the aftertreatment system of diesel to meet the real commercial demands.     

Influence of A-site Ba substitution on microwave dielectric properties of (BaxMg1−x)(A0.05Ti0.95)O3 (A=Zr,Sn) ceramics

The microwave dielectric properties of (Ba_xMg_1−x)(A_0.05Ti_0.95)TiO₃ (A=Zr, Sn) ceramics were investigated with regard to substitution of Ba for Mg of A-site. The microwave dielectric properties were correlated with the Ba content. With an increase in Ba content from 0.01 to 0.1, the dielectric constant and the τ_f value increased, but the Q×f value decreased. The sintered (Ba_xMg_1−x)(Zr_0.05Ti_0.95)TiO₃ (called B_xMZT) ceramics had a permittivity in the range of 19.1−20.6, quality factor from 180,000 to 25,000 GHz, and variation in temperature coefficient of resonant frequency from −35 to −39 ppm/°C with increasing composition x. For sintered (Ba_xMg_1−x)(Sn_0.05Ti_0.95)TiO₃ (called B_xMST) ceramics, the dielectric constant increased from 19 to 20.5, Q×f value increased from 120,000 to 37,000 (GHz), and the τ_f value increased from −50 to −3.3 ppm/°C as the x increased from 0.01 to 0.1. When A=Sn and x=0.1, (Ba_0.1Mg_0.9)(Sn_0.05Ti_0.95)TiO₃ ceramics exhibited dielectric constant of 20.5, Q×f value of 37,000 (GHz), and a near-zero τ_f value of −3.3 ppm/°C sintered at 1210 °C for 4 h.     

New binary (1 − x)Ba(Lu1/2Nb1/2)O3-xPbTiO3 solid solution with morphotropic phase boundary

A new ferroelectric solid solution of (1 − x)Ba(Lu_1/2Nb_1/2)O₃-xPbTiO₃ (BLN-PT) (0 ≤ x ≤ 1) has been synthesized by solid state reactions. Its structure and electric properties have been studied by X-ray diffraction and di-/ferro-electric measurements. Based on the investigation, a partial solid state phase diagram of the binary BLN-PT ceramics system has been established, which exhibits a morphotropic phase boundary (MPB) region in the composition range of 0.64 ≤ x ≤ 0.68. The Curie temperature is measured to be around 250 °C in the vicinity of the MPB region, which is much higher than that of PMNT or PZNT system. The dielectric behavior has been discussed based on Curie-Weiss Law and Lorentz-type quadratic relationship. With increasing PT content, a transformation from relaxor to ferroelectric phase has been demonstrated in the solid solution system.     

Quantitative study of pH change during LaNi5−xAlx (x = 0, 0.3) discharge process by SECM

Oxygen reduction reaction (ORR) on Pt microelectrode was used for developing a micro pH sensor for scanning electrochemical microscopy (SECM) study in this work. When the potential of Pt microelectrode was held constant in ORR region, the ORR current (cathodic current) increased with decreasing solution pH and vice versa. The response time of the ORR current to pH changes was measured to be ca. 30 ms which implies that the pH response is fast enough for monitoring the temporal pH changes. Furthermore, a fine linear relationship was found to exist between the half wave potential of ORR (E_1/2) and the solution pH value, and the slope is −46 mV/pH. The Pt micro pH sensor was located 1 μm above the LaNi_5−xAl_x (x = 0, 0.3) substrate electrode surface in pH = 9 KOH solution to perform the tip-substrate voltammetry of SECM. In tip voltammogram, the ORR tip current qualitatively reflects the transit solution pH changes during LaNi_5−xAl_x discharge reaction. Also, the minimum values of the solution pH near LaNi₅ and LaNi_4.7Al_0.3 surface during the discharge reaction were quantitatively detected; they were 7.17 and 7.57, respectively. The result indicates that Al partial substitution for Ni degrades the maximum discharge ability of the alloy and decreases the hydrogen diffusion coefficient in alloy bulk.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Ternary CdxZn1−xSe deposited on Ag (1 1 1) by ECALE: Electrochemical and EXAFS characterization

This paper reports the characterization of ternary II-VI semiconductor nanocrystals, deposited by the electrochemical atomic layer epitaxy (ECALE) technique.In particular, morphological and structural properties of the ternary compounds of formula Cd_xZn_1−xSe deposited on Ag (1 1 1) have been characterized as a function of composition. The number of the attainable x values is limited by the necessity of using well-defined ZnSe/CdSe deposition sequences. However, the quantitative analysis carried out on the basis of both electrochemical and extended X-ray absorption fine structure (EXAFS) experiments indicates that the ECALE method is a successful way of controlling the composition of Cd_xZn_1−xSe. In addition, the electrochemical measurements show that the amount of deposition is minimum in correspondence to the compound with x = 0.5, thus corroborating the hypothesis of a higher degree of disorder suggested both by morphological and structural investigation. The morphology was studied by atomic force microscopy (AFM). The structure of the films is estimated by EXAFS which is a powerful technique for the analysis of the local structure around chosen atoms.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Oxygen and chlorine evolution on RuO2 + TiO2 + CeO2 + Nb2O5 mixed oxide electrodes

A systematic investigation was conducted on the mechanism and electrocatalytic properties of O₂ and Cl₂ evolution on mixed oxide electrodes of nominal composition: Ti/[Ru_(0.3)Ti_(0.6)Ce_(0.1−x)]O₂[Nb₂O₅]_(x) (0 ≤ x ≤ 0.1). For the oxygen evolution, a 30 mV Tafel slope is obtained in the presence of CeO₂, while in its absence a 40 mV coefficient is observed. The intrinsic electrocatalytic activity is mainly due to electronic factors, as result of the synergism between Ru and Ce oxides. For chlorine evolution, the Tafel slope (30 mV) is independent on oxide composition. The best global electrocatalytic activity for ClER was observed in the absence of Nb₂O₅ additive. Variation of the voltammetric charge throughout the experiments confirms high CeO₂ content compositions are fragile, due mainly to the porosity caused by CeO₂ presence. On the other hand, Nb₂O₅ addition decreases considerably this instability.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Microstructures and electrochemical properties of Mg0.9Ti0.1Ni1−xMx (M = Co, Mn; x = 0, 0.1, 0.2) hydrogen storage alloys

Mg-Ni-Ti-based hydrogen storage alloys Mg_0.9Ti_0.1Ni_1−xM_x (M = Co, Mn; x = 0, 0.1, 0.2) were prepared by means of mechanical alloying (MA). The effects of partial substitution of Ni with Co or Mn on the microstructures and electrochemical performance of the alloys were investigated. The result of X-ray diffraction (XRD) shows that the alloys exhibit dominatingly amorphous structures. The electrochemical measurements indicate that the substitution of Ni can dramatically enhance the cycle stability of Mg-Ni-Ti-based alloys. After 50 charge/discharge cycles, the capacity retention rate of the alloy electrodes increases from 30% (Mg_0.9Ti_0.1Ni) to 59% (Mg_0.9Ti_0.1Ni_0.9Co_0.1), 58% (Mg_0.9Ti_0.1Ni_0.9Mn_0.1), 46% (Mg_0.9Ti_0.1Ni_0.8Co_0.2) and 53% (Mg_0.9Ti_0.1Ni_0.8Mn_0.2), respectively. Among these alloys, the Mg_0.9Ti_0.1Ni_0.9Mn_0.1 alloy presents better overall electrochemical performance. The cyclic voltammograms (CV) and anti-corruption test reveal that the electrochemical cycle stability of these alloys is improved by substituting Ni with Co or Mn.     

Effect of Pt addition on the isomerization properties of MoO2 − x(OH)y deposited on TiO2

Isomerization of n-hexane and n-pentane were studied using equivalent 5 monolayers of MoO₃ deposited on TiO₂. Addition of 2.5% Pt by weight of MoO₃ on the Mo catalyst resulted in an increase in the catalytic activity of the system in favor of hydrocracking products. Surface characterization by XPS-UPS and ISS reveal that the sample surface contains Oxygen, Molybdenum, Platinum and Titanium. Apparently, the metallic properties of the deposited Pt favors the hydrocracking reactions and becomes dominant at reaction temperatures higher than 623 K. Balanced metal-acid functions in MoO_2 − x(OH)_y phase seems to be in optimized condition toward the hydroisomerization process. The contribution of Platinum addition to this catalytic reaction is not obvious. Combination of surface XPS-UPS, ISS and catalytic reactions carried out at similar experimental conditions enabled us to have better insight concerning the catalytic activities of the different chemical species present on the sample surface.     

Synthesis and electrochemical characterization of mesoporous CoxNi1−x layered double hydroxides as electrode materials for supercapacitors

A novel nanostructured mesoporous Co_xNi_1−x layered double hydroxides (Co_xNi_1−x LDHs), which both Co(OH)₂ and Ni(OH)₂ exhibit, has been successfully synthesized by a chemical co-precipitation route using polyethylene glycol as the structure-directing reagent. Structural and morphological characterizations were performed using powder X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The component and thermal stability of the sample were measured by energy dispersed X-ray spectrometry (EDS), FT-IR and thermal analyses, including thermogravimetry (TG) and differential thermal analysis (DTA). Cyclic voltammogram and galvanostatic charge-discharge testified that the Co_xNi_1−x LDH has a specific capacitance of 1809 F g⁻¹ at a current density of 1 A g⁻¹ and remains at about 90.2% of the initial value after 1000 cycles at a current density of 10 A g⁻¹. The relationship between the chemical composition and the capacitance is discussed.     

Synthesis and microstructure of (LaSr)MnO3 and (LaSr)FeO3 ceramics by a reaction-sintering process

(La_xSr_1−x)MnO₃ (LSMO) and (La_xSr_1−x)FeO₃ (LSFO) (x = 0.2–0.4) ceramics prepared by a simple and effective reaction-sintering process were investigated. Without any calcination involved, La₂O₃ and SrCO₃ were mixed with MnO₂ (LSMO) or Fe₂O₃ (LSFO) then pressed and sintered directly. LSMO and LSFO ceramics were obtained after 2 and 4 h sintering at 1350–1400 and 1200–1280 °C, respectively. Grain size decreased as La content increased in LSMO and LSFO ceramics.     

Structure and electrochemical performances of Mg2Ni1−xMnx (x = 0-0.4) electrode alloys prepared by melt spinning

The melt-spinning technique is applied to the preparation of the nanocrystalline and amorphous Mg₂Ni-type alloys with nominal compositions of Mg₂Ni_1−xMn_x (x = 0, 0.1, 0.2, 0.3, 0.4). The as-spun alloy ribbons possessing a continuous length, a thickness of about 30 μm and a width of about 25 mm were prepared. The structures of the as-spun alloy ribbons are characterized by XRD and TEM. The electrochemical performances of the as-spun alloy ribbons are measured by an automatic galvanostatic system. The results show that no amorphous structure is detected in the as-spun Mg₂Ni alloy, whereas the as-spun Mg₂Ni_0.6Mn_0.4 alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Mn for Ni notably intensifies the amorphous forming ability of the Mg₂Ni-type alloy. The amorphization degree of the as-spun alloys containing Mn increases with increasing spinning rate. The melt spinning also significantly enhances the electrochemical performances such as the discharge capacity and the electrochemical cycle stability of the Mn-containing alloys. Furthermore, the high rate dischargeability (HRD) of the (x ≤ 0.1) alloys increases with an increase in the spinning rate, while for the (x ≥ 0.2) alloys, the HRD exhibits a maximum value at a particular spinning rate, and it varies with the change in Mn contents of the alloys.     

Preparation and cycling performance of Aland F co-substituted compounds Li4AlxTi5−xFyO12−y

Li₄Al_xTi_5−xF_yO_12−y compounds were prepared by a solid-state reaction method. Phase analyses demonstrated that both Al³⁺ and F⁻ ions entered the structure of spinel-type Li₄Ti₅O₁₂. Charge-discharge cycling results at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.5 and 0.5 V showed that the Al³⁺ and F⁻ substitutions improved the first total discharge capacity of Li₄Ti₅O₁₂. However, Al³⁺ substitution greatly increased the reversible capacity and cycling stability of Li₄Ti₅O₁₂ while F⁻ substitution decreased its reversible capacity and cycling stability slightly. The electrochemical performance of the Al³⁺-F⁻-co-substituted specimen was better than the F⁻-substituted one but worse than the Al³⁺-substituted one.