Effects of NOx-inhibitor agent on fuel properties of three-phase biodiesel emulsions

Biodiesel is one of the more promising alternative clean fuels to fossil fuel, which can reduce the emissions of fossil fuel burning, and possibly resolve the energy crisis caused by the exhaustion of petroleum resources in the near future. The burning of biodiesel emits much less gaseous emissions and particulate matter primarily because of its dominant combustion efficiency. However, the high oxygen content in biodiesel not only promotes the burning process but also enhances NO_x formation when biodiesel is used as fuel. Biodiesel emulsion and the additive of NO_x-inhibitor agent are considered to reduce levels of NO_x emissions in this experimental study. The biodiesel was produced by transesterification reaction accompanied with peroxidation process. A three-phase biodiesel emulsion of oil-in water drops-in oil (O/W/O) and an O/W/O biodiesel emulsion containing aqueous ammonia were prepared afterwards. The effect of the existence of NO_x-inhibitor agent on the fuel properties and the emulsion characteristics of the O/W/O biodiesel emulsions were investigated. The experimental results show that the burning of the O/W/O biodiesel emulsion and the O/W/O biodiesel emulsion containing aqueous ammonia had larger fraction of fuel burnt and thus larger heat release than the neat biodiesel if water content is not considered for the calculation of heating value. The addition of aqueous ammonia within the dispersed phase of the O/W/O biodiesel emulsion appeared to deteriorate the emulsification characteristics. A smaller quantity of emulsion and greater kinematic viscosity were formed while a larger carbon residue and actual reaction-heat release also appeared for this O/W/O biodiesel emulsion. Aqueous ammonia in the O/W/O biodiesel emulsion produces a higher pH value as well. In addition, the number as well as the volumetric fraction of the dispersed water droplets is reduced for the O/W/O biodiesel emulsion that contains aqueous ammonia.     

Effects of emulsification variables on fuel properties of two- and three-phase biodiesel emulsions

Biodiesel has attractive fuel properties such as excellent biodegradability and lubricity, almost no emissions of sulfur oxides, PAH and n-PAH, reduced CO₂, PM and CO emission, superior combustion efficiency, etc. However, burning of biodiesel generally produces higher levels of NO_x emissions, primarily due to its high oxygen content. In this study, the emulsification technology has been considered to reduce the NO_x emission level of fossil fuel. Biodiesel, produced by means of transesterification reaction accompanied with a peroxidation process, was emulsified to form two-phase W/O and three-phase O/W/O emulsions. The effects of the emulsification variables such as hydrophilic lipophilic balance (HLB), and water content on the fuel properties and emulsion characteristics of W/O and O/W/O emulsions were investigated in this study. The experimental results show that the surfactant mixture with HLB = 13 produced the highest emulsification stability while HLB = 6 produced the lowest emulsification stability and the most significant extent of water–oil separation among the various HLB values for O/W/O biodiesel emulsion. The kinematic viscosity, specific gravity and carbon residual of the biodiesel emulsions were larger than those of the neat biodiesel. In addition, the W/O biodiesel emulsion was found to have a smaller mean droplet size, lower volumetric fraction of the dispersed phase than the O/W/O biodiesel emulsion, and the highest heating value among the test fuels, if the water content is deducted from the calculation of the heating value.     

Mitigation of NOx emissions from a jatropha biodiesel fuelled DI diesel engine using antioxidant additives

Biodiesel offers cleaner combustion over conventional diesel fuel including reduced particulate matter, carbon monoxide and unburned hydrocarbon emissions. However, several studies point to slight increase in NO_x emissions (about 10%) for biodiesel fuel compared with conventional diesel fuel. Use of antioxidant additives is one of the most cost-effective ways to mitigate the formation of prompt NO_x. In this study, the effect of antioxidant additives on NO_x emissions in a jatropha methyl ester fuelled direct injection diesel engine have been investigated experimentally and compared. A survey of literature regarding the causes of biodiesel NO_x effect and control strategies is presented. The antioxidant additives L-ascorbic acid, α tocopherol acetate, butylated hydroxytoluene, p-phenylenediamine and ethylenediamine were tested on computerised Kirloskar-make 4 stroke water cooled single cylinder diesel engine of 4.4 kW rated power. Results showed that antioxidants considered in the present study are effective in controlling the NO_x emissions of biodiesel fuelled diesel engines. A 0.025%-m concentration of p-phenylenediamine additive was optimal as NO_x levels were substantially reduced in the whole load range in comparison with neat biodiesel. However, hydrocarbon and CO emissions were found to have increased by the addition of antioxidants.     

Biodiesel engine performance and emissions in low temperature combustion

Engine performance and emission comparisons were made between the use of soy, Canola and yellow grease derived B100 biodiesel fuels and an ultra-low sulphur diesel fuel in the high load engine operating conditions. Compared to the diesel fuel engine-out emissions of nitrogen oxides (NO_x), a high-cetane number (CN) biodiesel fuel produced comparable NO_x while the biodiesel with a CN similar to the diesel fuel produced relatively higher NO_x at a fixed start of injection. The soot, carbon monoxide and un-burnt hydrocarbon emissions were generally lower for the biodiesel-fuelled engine. Exhaust gas recirculation (EGR) was then extensively applied to initiate low temperature combustion (LTC) mode at medium and low load conditions. An intake throttling valve was implemented to increase the differential pressure between the intake and exhaust in order to increase and enhance the EGR. Simultaneous reduction of NO_x and soot was achieved when the ignition delay was prolonged by more than 50% from the case with 0% EGR at low load conditions. Furthermore, a preliminary ignition delay correlation under the influence of EGR at steady-state conditions was developed. The correlation considered the fuel CN and oxygen concentrations in the intake air and fuel. The research intends to achieve simultaneous reductions of NO_x and soot emissions in modern production diesel engines when biodiesel is applied.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Performance of compression ignition engine with mahua (Madhuca indica) biodiesel

The performance of biodiesel obtained from mahua oil and its blend with high speed diesel in a Ricardo E6 engine has been presented in this paper together with some of its fuel properties. These properties were found to be comparable to diesel and confirming to both the American and European standards. Engine performance (brake specific fuel consumption, brake thermal efficiency and exhaust gas temperature) and emissions (CO, smoke density and NO_x) were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The reductions in exhaust emissions and brake specific fuel consumption together with increase brake power, brake thermal efficiency made the blend of biodiesel (B20) a suitable alternative fuel for diesel and thus could help in controlling air pollution.     

Combustion and emissions characteristics of compression-ignition engine using dual ammonia-diesel fuel

This study investigated the combustion and emissions characteristics of a compression-ignition engine using a dual-fuel approach with ammonia and diesel fuel. Ammonia can be regarded as a hydrogen carrier and used as a fuel, and its combustion does not produce carbon dioxide. In this study, ammonia vapor was introduced into the intake manifold and diesel fuel was injected into the cylinder to initiate combustion. The test engine was a four-cylinder, turbocharged diesel engine with slight modifications to the intake manifold for ammonia induction. An ammonia fueling system was developed, and various combinations of ammonia and diesel fuel were successfully tested. One scheme was to use different combinations of ammonia and diesel fuel to achieve a constant engine power. The other was to use a small quantity of diesel fuel and vary the amount of ammonia to achieve variable engine power. Under the constant engine power operation, in order to achieve favorable fuel efficiency, the preferred operation range was to use 40-60% energy provided by diesel fuel in conjunction with 60-40% energy supplied by ammonia. Exhaust carbon monoxide and hydrocarbon emissions using the dual-fuel approach were generally higher than those of using pure diesel fuel to achieve the same power output, while NO_x emissions varied with different fueling combinations. NO_x emissions could be reduced if ammonia accounted for less than 40% of the total fuel energy due to the lower combustion temperature resulting in lower thermal NO_x. If ammonia accounted for the majority of the fuel energy, NO_x emissions increased significantly due to the fuel-bound nitrogen. On the other hand, soot emissions could be reduced significantly if a significant amount of ammonia was used due to the lack of carbon present in the combination of fuels. Despite the overall high ammonia conversion efficiency (nearly 100%), exhaust ammonia emissions ranged from 1000 to 3000 ppmV and further after-treatment will be required due to health concerns. On the other hand, the variable engine power operation resulted in relatively poor fuel efficiency and high exhaust ammonia emissions due to the lack of diesel energy to initiate effective combustion of the lean ammonia-air mixture. The in-cylinder pressure history was also analyzed, and results indicated that ignition delay increased with increasing amounts of ammonia due to its high resistance to autoignition. The peak cylinder pressure also decreased because of the lower combustion temperature of ammonia. It is recommended that further combustion optimization using direct ammonia/diesel injection strategies be performed to increase the combustion efficiency and reduce exhaust ammonia emissions.     

Combustion, performance and emission characteristics of a DI diesel engine fueled with ethanol-biodiesel blends

In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NO_x and particulate emissions of the diesel engine. The effectiveness of NO_x and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.     

Performance and emission characteristics of an CI engine fueled with diesel–biodiesel–bioethanol blends

The paper presents the experimental results obtained concerning performances and pollution of a diesel engine fueled with diesel–biodiesel–ethanol blends compared with diesel fuel in laboratory tests. The main properties of the researched fuels are presented within this paper, in comparison with classical diesel fuel (chemical composition, density, kinematic viscosity, cold filter plugging point, flash point). Engines’ performances were evaluated by determining the brake specific fuel consumption and brake thermal efficiency. For pollution evaluation the emissions of CO, CO₂, NO_x, HC and smoke have been measured. An increasing of brake specific fuel consumption has been observed, especially at lower engines’ loads, with maximum 32.4%, reducing engine brake thermal efficiency with maximum 21.7%. CO emissions decrease, especially at high loads with maximum 59%, on the basis of CO₂ increased emissions. NO_x emissions slightly increase, especially at partial and high loads, meanwhile HC and smoke emissions decrease in all engines’ load cycles.     

Diesel engine performance and emission characteristics of biodiesel produced by the peroxidation process

Biodiesel is an alternative fuel that is cleaner than petrodiesel. Biodiesel can be used directly as fuel for a diesel engine without having to modify the engine system. It has the major advantages of having high biodegradability, excellent lubricity and no sulfur content. In this study, the biodiesel produced by a transesterification technique was further reacted by using a peroxidation process. Four types of diesel fuel, biodiesel with and without an additional peroxidation process, a commercial biodiesel and ASTM No. 2D diesel were compared for their fuel properties, engine performance and emission characteristics. The experimental results show that the fuel consumption rate, brake thermal efficiency, equivalence ratio, and exhaust gas temperature increased while the bsfc, emission indices of CO₂, CO and NO_x decreased with an increase of engine speed. The three biodiesels showed a higher fuel consumption rate, bsfc, and brake thermal efficiency, while at the same time exhibited lower emission indices of CO and CO₂ as well as a lower exhaust gas temperature when compared to ASTM No. 2D diesel. Moreover, the biodiesel produced with the additional peroxidation process was found to have an oxygen content, weight proportion of saturated carbon bonds, fuel consumption rate, and bsfc that were higher than the biodiesel produced without the additional process; while at the same time the brake thermal efficiency, equivalence ratio, and emission indices of CO₂, CO and NO_x were found to be lower. In particular, biodiesel produced with the addition of the peroxidation process had the lowest equivalence ratio and emission indices of CO₂, CO and NO_x among all of the four test fuels. Therefore, the peroxidation process can be used to effectively improve the fuel properties and reduce emissions when biodiesel is used.     

Determination of performance and exhaust emissions properties of B75 in a CI engine application

In this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO₂, and O₂ emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2-3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO₂, CO, HC, smoke opacity and NO_x emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.     

Engine performance and emission characteristics of three-phase diesel emulsions prepared by an ultrasonic emulsification method

The emulsification method is a potential technique for reducing pollutant emissions from combustion equipment primarily due to occurrence of micro-explosion to enhance burning. In this study, an ultrasonic emulsification method was applied to prepare two-phase water-in-oil (W/O) and three-phase oil-in-water-in-oil (O/W/O) emulsions. The engine performance and the pollutant emission characteristics of a diesel engine were measured and analyzed. A rather violent ultrasonic wave may result in the phenomena of cavitations and hot spots, which in turn promotes fast chemical and physical reactions. Various kinds of liquid, which are immiscible with each other, may thus become highly mixed so that an emulsion is formed. This study first used an ultrasonic oscillating bath to produce ultrasonic waves by which two- and three-phase emulsions were prepared. The experimental results show that the emulsions prepared by the ultrasonic vibrating method have much finer and better-distributed droplets. The use of these emulsions as an engine fuel produced lower NO emission, lower soot concentration and lower black smoke opacity, while creating a larger brake specific fuel consumption (bsfc) and a larger CO emission compared with that of an engine using neat diesel fuel. However, the variations in the concentrations of CO₂ and O₂ emissions between the emulsions and neat diesel fuel were not significant. In a comparison with the characteristics of the two-phase W/O emulsion, the three-phase O/W/O emulsion was found to have a larger CO emission, larger soot particles and larger bsfc while producing a lower brake thermal efficiency and a lower black smoke opacity.     

Real-time and robust estimation of biodiesel blends

Biodiesel as a renewable alternative fuel produces lower exhaust emissions with the exception of nitrogen oxides (NO_x) when compared to the conventional diesel fuel. Reducing nitrogen oxides produced from engines running on biodiesel requires proper engine controller adaptations that are linked to the specifics of the fuel blend. Therefore, online estimation of fuel blend is a critical step in allowing diesel engines to maintain performance while simultaneously meeting emission requirements when operating on biodiesel blends. Presented in this paper are three different model-based biodiesel blend estimation strategies using: (i) crankshaft torsionals, (ii) NO_x emissions measurement from the exhaust stream, and (iii) oxygen content measurement of the exhaust stream using a wide-band UEGO sensor. Each approach is investigated in terms of the accuracy and robustness to sensor errors. A sensitivity analysis is conducted for each method to quantify robustness of the proposed fuel blend estimation methods.     

Diesel engine performance and emission evaluation using emulsified fuels stabilized by conventional and gemini surfactants

Diesel engines exhausting gaseous emission and particulate matter have long been regarded as one of the major air pollution sources, particularly in metropolitan areas, and have been a source of serious public concern for a long time. The emulsification method is not only motivated by cost reduction but is also one of the potentially effective techniques to reduce exhaust emission from diesel engines. Water/diesel (W/D) emulsified formulations are reported to reduce the emissions of NO_x, SO_x, CO and particulate matter (PM) without compensating the engine’s performance. Emulsion fuels with varying contents of water and diesel were prepared and stabilized by conventional and gemini surfactant, respectively. Surfactant’s dosage, emulsification time, stirring intensity, emulsifying temperature and mixing time have been reported. Diesel engine performance and exhaust emission was also measured and analyzed with these indigenously prepared emulsified fuels. The obtained experimental results indicate that the emulsions stabilized by gemini surfactant have much finer and better-distributed water droplets as compared to those stabilized by conventional surfactant. A comparative study involving torque, engine brake mean effective pressure (BMEP), specific fuel consumption (SFC), particulate matter (PM), NO_x and CO emissions is also reported for neat diesel and emulsified formulations. It was found that there was an insignificant reduction in engine’s efficiency but on the other hand there are significant benefits associated with the incorporation of water contents in diesel regarding environmental hazards. The biggest reduction in PM, NO_x, CO and SO_x emission was achieved by the emulsion stabilized by gemini surfactant containing 15% water contents.     

Potential for reducing emissions in a diesel engine by fuelling with conventional biodiesel and Fischer-Tropsch diesel

A gas-to-liquid (GTL) fuel derived from Low Temperature Fischer-Tropsch process has been tested in an automotive diesel engine fulfilling Euro 4 emissions regulations. Both regulated and non-regulated emissions have been compared with those of a commercial diesel fuel, a commercial biodiesel fuel and a GTL-biodiesel fuel (30% and 70% v/v, respectively) in order to check blending properties, synergistic effects and compatibility between first and second generation production technologies for biofuel consumption in current diesel engines. After presenting a detailed literature review, and confirming that similar efficiencies are attained with the four tested fuels under identical road-like operating conditions (this meaning fuel consumption is inversely proportional to their heating values), significant reductions in smoke opacity, particulate matter emissions and particle number concentration were observed with both GTL and biodiesel fuels, with small changes in NO_x emissions. Compared with the reductions in PM emissions derived from the use of biodiesel fuels, those derived from using GTL fuels were quite similar, despite its lower soot emissions reductions. This can be explained by the lower volatile organic fraction of the PM in the case of GTL. By adequately blending both fuels, a considerable potential to optimise the engine emissions trade-off is foreseen.     

Evaluation of formulation strategies to eliminate the biodiesel NOx effect

In this paper, we explore the efficacy of (1) reducing the iodine value of soy-derived biodiesel fuels through increasing the methyl oleate (methyl ester of oleic acid) content and (2) addition of cetane improvers, as strategies to combat the biodiesel NO_x effect: the increase in NO_x emissions observed in most studies of biodiesel and biodiesel blends. This is accomplished by spiking a conventional soy-derived biodiesel fuel with methyl oleate or with cetane improver. The impact on bulk modulus of compressibility, fuel injection timing, cetane number, combustion, and emissions were examined. The conventional B20 blend produced a NO_x increase of 3–5% relative to petroleum diesel, depending on injection timing. However, by using a B20 blend where the biodiesel portion contained 76% methyl oleate, the biodiesel NO_x effect was eliminated and a NO_x neutral blend was produced. The bulk modulus of petroleum diesel was measured to be 2% lower than B20, yielding a shift in fuel injection timing of 0.1–0.3 crank angle. The bulk modulus of the high methyl oleate B20 blend was measured to be 0.5% lower than B20, not enough to have a measurable impact on fuel injection timing. Increasing the methyl oleate portion of the biodiesel to 76% also had the effect of increasing the cetane number from 48.2 for conventional B20 to 50.4, but this effect is small compared to the increase to 53.5 achieved by adding 1000 ppm of 2-ethylhexyl nitrate (EHN) to B20. For the particular engine tested, NO_x emissions were found to be insensitive to ignition delay, maximum cylinder temperature, and maximum rate of heat release. The dominant effect on NO_x emissions was the timing of the combustion process, initiated by the start of injection, and propagated through the timing of maximum heat release rate and maximum temperature.     

Study of oxygenated biomass fuel blends on a diesel engine

Vegetable methyl ester was added in ethanol–diesel fuel to prevent separation of ethanol from diesel in this study. The ethanol blend proportion can be increased to 30% in volume by adding the vegetable methyl ester. Engine performance and emissions characteristics of the fuel blends were investigated on a diesel engine and compared with those of diesel fuel. Experimental results show that the torque of the engine is decreased by 6%–7% for every 10% (by volume) ethanol added to the diesel fuel without modification on the engine. Brake specific fuel consumption (BSFC) increases with the addition of oxygen from ethanol but equivalent brake specific fuel consumption (EBSFC) of oxygenated fuels is at the same level of that of diesel. Smoke and particulate matter (PM) emissions decrease significantly with the increase of oxygen content in the fuel. However, PM reduction is less significant than smoke reduction. In addition, PM components are affected by the oxygenated fuel. When blended fuels are used, nitrogen oxides (NO_x) emissions are almost the same as or slightly higher than the NO_x emissions when diesel fuel is used. Hydrocarbon (HC) is apparently decreased when the engine was fueled with ethanol–ester–diesel blends. Fuelling the engine with oxygenated diesel fuels showed increased carbon monoxide (CO) emissions at low and medium loads, but reduced CO emissions at high and full loads, when compared to pure diesel fuel.     

Comparison of emissions of a direct injection diesel engine operating on biodiesel with emulsified and fumigated methanol

Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NO_x) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO₂, NO_x, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal efficiency at low engine load while the fumigation mode gives slightly higher brake thermal efficiency at medium and high engine loads. In the fumigation mode, an extra fuel injection control system is required, and there is also an increase in CO, HC and NO₂ (nitrogen dioxide) and particulate emissions in the engine exhaust, which are disadvantages compared with the blended mode.     

Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine

Non-edible filtered high viscous (72 cSt at 40 °C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO₂, HC, NO_x, and O₂) were recorded. The optimum engine operating condition based on lower brake specific fuel consumption and higher brake thermal efficiency was observed at 100% load for neat biodiesel. From emission point of view the neat POME was found to be the best fuel as it showed lesser exhaust emission as compared to HSD.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.