孔隙尺寸、盐度和气体组分对水合物相平衡的影响(英文)

An experimental device was set up to study the hydrate formation conditions. Effects of pore size, salinity, and gas composition on the formation and dissociation of hydrates were investigated. The result indicates that the induction time for the formation of hydrates in porous media is shorter than that in pure water. The decrease in pore size, by decreasing the size of glass beads, increases the equilibrium pressure when the salinity and temperature are kept constant. In addition, higher salinity causes higher equilibrium pressure when the pore size and temperature are kept constant. It is found that the effects of pore size and salinity on the hydrate equilibrium are quite different. At lower methane concentration, the hydrate equilibrium is achieved at lower pressure and higher temperature.     

表面活性剂在瓦斯水合物生成过程中的热力学作用

在实验研究基础上,结合表面活性剂水溶液中瓦斯水合物生成微观机理,提出了表面活性剂改变水合物生成热力学条件物理作用假说,认为表面活性剂胶束对溶于其中的气体分子和吸附于其周围的水分子的束缚作用,相当于降低了体系的温度.利用T40（0.001 mol·L^-1）、T40（0.002 mol·L^-1）、T40/T80（0.001 mol·L^-1）分别组成的3种气 液 煤 水合物反应体系实验测定了水合物生成时的相平衡参数,与同样温度和压力条件下相平衡计算值比较,结果表明,表面活性剂的加入有效地改变了水合物生成的热力学条件.例如,在T40/T80（0.001 mol·L^-1）实验体系中,当压力为22.67 MPa时,水合物生成相平衡温度为22.6℃,比纯水中提高2.1℃.     

天然气水合物颗粒微观受力及聚集特性研究进展

水合物颗粒微观受力和聚集是影响水合物浆稳定流动的关键,本文调研了国内外研究水合物颗粒受力和聚集常用的测量装置,主要有聚焦光束反射测量仪、颗粒图像显微镜、高压差示扫描量热仪、微机械测力装置;受力测量和理论研究证明了毛细液桥力是导致水合物颗粒聚集的主要黏附力;介绍了常用于水合物聚集特性研究的受力平衡模型,通过该模型可以计算得到水合物颗粒最大临界聚集粒径;总结了众学者提出的水合物颗粒聚集机理,并阐述了基于群体平衡模型建立的接触诱导-剪切限制聚集机理的物理模型,该模型能够很好地描述水合物颗粒的动态聚集过程;水合物颗粒微观受力和聚集机理的深入研究和明确将对石油天然气的输送具有非常重大的意义,确定防聚集对水合物聚集的影响是未来研究的重点。     

Effect of additives on formation of natural gas hydrate

The formation of natural gas hydrate (NGH) is studied in this work. Kinetics data of hydrate formation with no agitation were collected at various concentrations of the aqueous solutions with different additives such as alkylpolyglucside, sodium dodecyl benzene sulfonate and potassium oxalate monohydrate. Various kinds of additive increased the formation rates of NGH and its storage capacity and reduced the induction time of NGH formation. Moreover, the storage capacity, the induction time and the hydrate formation rate were influenced by the concentration of the aqueous solution.     

气体水合物形成的热力学与动力学研究进展

气体水合物形成过程中涉及复杂的热力学和动力学问题.本文对水合物热力学理论模型、水合物生成动力学机理等方面的研究成果和最新进展进行了综述.热力学方面重点介绍了基于等温吸附理论 (van der Waals-Platteeuw模型)和基于双过程水合物生成机理(Chen-Guo模型)的相平衡热力学模型,同时介绍水合物结构及其转变方面的最新研究成果.动力学方面介绍了成簇成核、界面成核等成核机理模型以及成核后的水合物生长机理.另外还述及了目前水合物热力学和动力学研究中所涉及的微观、亚微观和宏观测量方法.针对目前水合物热力学和动力学研究中存在的问题,对未来的发展方向和重点提出了建议.     

水逸度模型预测THF添加剂体系下气体水合物相平衡

加入添加剂降低水合物生成压力是当前水合物法分离混合气体研究热点。本研究以水的逸度模型为基础, 结合PRSV2 状态方程研究了CH₄、O₂、N₂ 及其混合气体水合物在纯水体系下的相平衡条件;通过UNIFAC 基团 贡献法对添加剂四氢呋喃(THF)水溶液进行基团划分,计算该体系下液相各组分的活度,理论研究了添加剂 THF 对气体水合物相平衡条件的影响;结果表明在相应的温度范围内,与其他模型相比,在纯水体系下该模型 预测精度较高,在THF 水溶液体系下该模型对单组分和双组分气体的预测精度平均相对误差在7%左右,随着 THF 浓度增加,气体水合物相平衡压力的降低幅度减小;当THF 摩尔分数达到6%时,对气体水合物相平衡影 响达到最大。相关研究结果为混合气体的大规模工业提纯分离提供了理论基础。     

Methane-ethane and methane-propane hydrate formation and decomposition on water droplets

Gas hydrate formation and decomposition on water droplets using an 89.4% methane—10.6% ethane mixture, and a 90.1% methane—9.9% propane mixture were carried out in a new apparatus suitable for morphology studies. As expected the induction time was found to be much shorter when the water had hydrate memory. All droplets nucleated simultaneously and the droplet size and shape had no noticeable effect on induction time and macroscopic crystal growth morphology for hydrates from the methane-ethane mixture. However, the surface of the hydrate crystals from methane-propane had a “hairy-like” appearance which changed to a smooth surface over time. Moreover, the smaller droplets during hydrate reformation showed an extensive hydrate growth and looked like snow-flakes. Sequential pictures generated by time-lapse videos showed that the time required for hydrate to cover the water droplet surface ranged from 10 to 23 s and was shorter when there was gas-phase agitation (mixing). The growth is postulated to occur in two stages. The first stage lasts about 10-23 s and growth takes place laterally. Growth takes place at the hydrate/gas and the hydrate/water interfaces during the second stage. The implication of the findings for process design of hydrate formation vessels is also discussed.     

Inhibitory effects of novel green inhibitors on gas hydrate formation

Natural gas hydrates easily form in pipelines, causing potential safety issues during oil and gas production and transportation. Injecting gas hydrate inhibitors is one of the most effective methods for preventing gas hydrate formation or aggregation. However, some thermodynamic hydrate inhibitors are toxic and harmful to the environment, whereas degradation of kinetic inhibitors is difficult. Therefore, environmentally friendly and easily biodegradable novel green inhibitors have been proposed and investigated. This paper provides a short but systematic review of the inhibitory performance of amino acids, antifreeze proteins, and ionic liquids. For different hydrate formation systems, the influences of the inhibitor type, structure, and concentration on the inhibitory effects are summarized. The mechanism of green inhibitors as kinetic inhibitors is also discussed. The progress described here will facilitate further developments of such green inhibitors for gas hydrate formation.     

The modelling of hydrocarbon bubble plumes to include gas hydrate formation

Information gained on hydrate formation on a single rising bubble of hydrocarbon gas is applied to the case of a complete bubble plume. When hydrate formation is included in the plume equations there is a strong coupling between small scale bubble behaviour and the total plume buoyancy. The sensitiv of the plume solutions to this coupling is examined for methane and a natural gas typical of certain Arctic oilwells. The results of the latter are app to a hypothetical oilwell blowout under Arctic conditions, and indicate that for wellhead depths greater than 800 m all the gas will be converted to hy before the surface is reached.     

长输管道内天然气水合物形成的预测

长距离天然气输送管道输送压力一般较高,管道内易形成水合物而阻塞管道.长输管道内压力温度变化复杂,难于精确判断水合物的形成.针对这一问题,本文分析了长输管道内压力温度的变化规律,给出了判断水合物形成的理论模型和计算方法.并将计算结果与实验值做了比较,结果表明该模型具有较高的精度.     

SDBS的表面张力对天然气水合物生成的影响

利用德国KRUSS公司生产的界面张力仪K11中的板法测定十二烷基苯磺酸钠在不同温度(5,10,20,30,35℃)和不同浓度下(100,400,800,1200,1600,2000 mg/L)的表面张力,确定有利于天然气水合物合成的最佳浓度为1 200 mg/L,这在工业应用中有着重要的参考价值,同时分析了表面活性剂加速天然气水合物生成的机理。     

海底天然气水合物生成影响因素研究进展

通过归纳总结众多研究成果,综述了海底天然气水合物生成的影响因素,并对影响因素中的温压条件、构造条件、沉积条件、气源条件加以详细阐述。最后提出目前研究工作中还存在的一些问题:经验公式计算水合物赋存温度存在一定误差;水合物成矿与沉积物颗粒粗细的关系机理不明确;如何提高水合物的精准预测程度等,这都需要加大研究力度。     

海底天然气水合物生成影响因素研究进展

通过归纳总结众多研究成果,综述了海底天然气水合物生成的影响因素,并对影响因素中的温压条件、构造条件、沉积条件、气源条件加以详细阐述。最后提出目前研究工作中还存在的一些问题:经验公式计算水合物赋存温度存在一定误差;水合物成矿与沉积物颗粒粗细的关系机理不明确;如何提高水合物的精准预测程度等,这都需要加大研究力度。     

气体水合物快速生成强化技术与方法研究进展

水合物技术可应用于天然气储运、污水处理、海水淡化、混合气体分离、水溶液浓缩以及水合物蓄冷等领域,而该技术成功应用的关键在于如何强化水合物快速生成.本文介绍了水合物的生成机理,综述了气体水合物快速生成强化技术与方法研究进展,分析了各自的优缺点,并对气体水合物快速生成技术进行了展望.     

Modelling hydrate formation kinetics of a hydrate promoter-water-natural gas system in a semi-batch spray reactor

Hydrate formation kinetic modelling studies reported so far mainly concentrates on pure water-gas systems in stirred-tank batch environments. This work proposes a model for gas hydrate formation kinetics of a hydrate promoter-water-natural gas system in a semi-batch reactor assuming steady-state, isothermal and isobaric conditions. The hydrate formation kinetics was modelled after extending the recent method proposed by Kashchiev and Firoozabadi (J. Crystral Growth 241 (2002a) 220; J. Crystal Growth 243 (2002b) 476; J. Crystal Growth 250 (2003) 499) for a single component gas-water system to a multi-component gas-water-additive system. The extended Kashchiev and Firoozabadi model was applied for a semi-batch spray reactor here for the first time. The hydrate formation experiments were carried out in a pilot plant spray reactor at three different pressure-temperature regimes to determine the actual hydrate formation kinetics in the spray reactor. The experiment results were then used to finetune the adjustable parameters to facilitate accurate model predictions.     

多孔介质中水合物生成与分解的电阻率性质

A new one-dimensional system for resistivity measurement for natural gas hydrate (NGH) exploitation is designed, which is used to study the formation and decomposition processes of NGH.The experimental results verify the feasibility of the measurement method, especially in monitoring the nucleation and growth of the NGH.Isovolumetric formation experiment of NGH is performed at 2 ℃ and 7.8 MPa.Before the NGH formation, the ini-tial resistivity is measured to be 4-7 Ω·m, which declines to the minimum value of 2-3 Ω·m when NGH begins to nucleate after the pressure is reduced to 3.3 MPa.As the NGH grows, the resistivity increases to a great extent, and finally it keeps at 11-13 Ω·m, indicating the completion of the formation process.The NGH decomposition ex-periment is then performed.When the outlet pressure decreases, NGH begins to decompose, accordingly, the resis-tivity declines gradually, and is at 5-9 Ω·m when the decomposition process ends, which is slightly higher than the resistivity value before the formation of NGH.The occurrence and distribution uniformity of NGH are determined by the distribution and magnitude of the resistivity measured on an one-dimensional sand-packed model.This study tackles the accurate estimation for the distribution of NGH in porous medium, and provides an experimental basis for further study on NGH exploitation in the future.     

Kinetics of gas hydrate formation from mixtures of methane and ethane

Experimental data on the kinetics of formation of gas hydrates from three mixtures of gaseous methane and ethane are reported. the experiments were conducted in a semi-batch stirred tank reactor at temperatures from 273 to 284 K and of pressures from 0.68 to 5.60 MPa. An intrinsic kinetic model for the growth of the gas hydrate is proposed. It is extension of the model for pure component hydrate formation. The model is based on the crystallization theory coupled with the two-film theory for the gas absorption into the liquid phase. the model does not contain any adjustable parameters. The kinetic rate constants which appear in the model are those obtained previously from pure component formation data. The results indicate that the formation rate is proportional to a lienar combination of the differences in the fugacities of the dissolved gases and their three-phase equilibrium fugacities at the experimental temperature. The effect of the mixture composition is taken into account indirectly through the computation of the three-phase equilibrium conditions and of the fugacities. the total gas consumption rate is proportional to the second moment of the particle size distribution.     

天然气水合物形成与生长影响因素综述

天然气水合物(NGH)是水分子和天然气分子形成的一种复杂的笼型晶体,其在油气管道输送、天然气储存和制冷等行业中都具有重要的研究意义和利用价值,但天然气水合物的形成是一个多组分、多阶段的复杂过程,不同因素对于天然气水合物形成和生长的影响尚有待明确。本文介绍了天然气水合物形成的物理过程以及水合物成核的3种机理假说;详细梳理了基质两亲性、添加剂、多孔介质环境和杂质、液体组成、温度压力以及流动条件等因素对于天然气水合物形成和生长的影响,并对其作了简要分析。同时指出,原油组成对于水合物抑制效果的定量化、蜡晶结构对于水合物形成过程中传质和传热的影响以及微观化的动力学抑制剂抑制机理等都是水合物相关研究中需要进一步深入探究和明确的问题。     

气体水合物生成微观机理及分析方法研究进展

水合物技术在能源和气候领域有着广阔的应用前景,有望成为应对能源挑战和气候变化的关键技术。但目前该技术存在着水合物生成速率慢、气体消耗量低的缺点,限制了水合物技术的工业化发展。从微观机理的角度,梳理和总结了关于气体水合物生成机制的理论观点,简述了驱动力和气体溶解度在水合物成核过程中的影响,介绍了表面活性剂和纳米粒子对水合物形成的影响机理以及常用的微观分析技术。分析发现,气体水合物的形成机制时至今日仍未有统一定论,对于促进剂作用机理的研究也不够充分,现有的微观分析手段难以捕捉水合物形成过程中的分子行为。这些问题限制了水合物技术向更快、更高效方面发展。探究水合物技术的相关机理,了解各类影响因素的作用原理,探索新的分析手段,将有助于突破水合物技术的瓶颈,为寻找更佳性能的促进剂、更高效地合成水合物探明道路。