Low-temperature H2-SCR of NO on a novel Pt/MgO-CeO2 catalyst

The selective catalytic reduction of NO by H₂ under strongly oxidizing conditions (H₂-SCR) in the low-temperature range of 100–200 °C has been studied over Pt supported on a series of metal oxides (e.g., La₂O₃, MgO, Y₂O₃, CaO, CeO₂, TiO₂, SiO₂ and MgO-CeO₂). The Pt/MgO and Pt/CeO₂ solids showed the best catalytic behavior with respect to N₂ yield and the widest temperature window of operation compared with the other single metal oxide-supported Pt solids. An optimum 50 wt% MgO-50wt% CeO₂ support composition and 0.3 wt% Pt loading (in the 0.1–2.0 wt% range) were found in terms of specific reaction rate of N₂ production (mols N₂/g_cat s). High NO conversions (70–95%) and N₂ selectivities (80–85%) were also obtained in the 100–200 °C range at a GHSV of 80,000 h⁻¹ with the lowest 0.1 wt% Pt loading and using a feed stream of 0.25 vol% NO, 1 vol% H₂, 5 vol% O₂ and He as balance gas. Addition of 5 vol% H₂O in the latter feed stream had a positive influence on the catalytic performance and practically no effect on the stability of the 0.1 wt% Pt/MgO-CeO₂ during 24 h on reaction stream. Moreover, the latter catalytic system exhibited a high stability in the presence of 25–40 ppm SO₂ in the feed stream following a given support pretreatment. N₂ selectivity values in the 80–85% range were obtained over the 0.1 wt% Pt/MgO-CeO₂ catalyst in the 100–200 °C range in the presence of water and SO₂ in the feed stream. The above-mentioned results led to the obtainment of patents for the commercial exploitation of Pt/MgO-CeO₂ catalyst towards a new NO_x control technology in the low-temperature range of 100–200 °C using H₂ as reducing agent. Temperature-programmed desorption (TPD) of NO, and transient titration of the adsorbed surface intermediate NO_x species with H₂ experiments, following reaction, have revealed important information towards the understanding of basic mechanistic issues of the present catalytic system (e.g., surface coverage, number and location of active NO_x intermediate species, NO_x spillover).     

Low-temperature H2 and N2 transport through thin Pd66Cu34Hx layers

The single gas H₂ and N₂ permeability of a 4 μm thick dense fcc-Pd₆₆Cu₃₄ layer has been studied between room temperature and 510 °C and at pressure differences up to 400 kPa. Above 50 °C the H₂ flux exhibits an Arrhenius-type temperature dependence with J_H2=(5.2±0.3) mol m⁻² s⁻¹ exp[(−21.3 ± 0.2) kJ mol⁻¹/(R·T)]. The hydrogen transport rate is controlled by the bulk diffusion although the pressure dependence of the H₂ flux deviates slightly from Sieverts’ law. A sudden increase of the H₂ flux below 50 °C is attributed to embrittlement.     

Crystal structure of zeolite X nickel(II) exchanged at pH 4.3 and partially dehydrated, Ni2(NiOH)35(Ni4AlO4)2(H3O)46Si101Al91O384

Complete Ni²⁺ exchange of a single crystal of zeolite X of composition Na₉₂Si₁₀₀Al₉₂O₃₈₄ per unit cell was attempted at 73°C with flowing aqueous 0.05 M NiCl₂ (pH=4.3 at 23°C). After partial dehydration at 23°C and ≈10⁻³ Torr for two days, its structure, now of composition Ni₂(NiOH)₃₅(Ni₄AlO₄)₂(H₃O)₄₆Si₁₀₁Al₉₁O₃₈₄ per unit cell, was determined by X-ray diffraction techniques at 23°C (space group Fd , a₀=24.788(5) Å). It was refined using all intensities; R₁=0.080 for the 236 reflections for which F_o>4σ(F_o), and wR₂=0.187 using all 1138 unique reflections measured. At four crystallographic sites, 45 Ni²⁺ ions were found per unit cell. Thirty of these are at two different site III′ positions. Twenty of those are close to the sides of 12-rings near O–Si–O sequences, where each coordinates octahedrally to two framework oxygens, to three water molecules which hydrogen bond to the zeolite framework, and to an OH⁻ ion. The remaining 10 are near O–Al–O sequences; only three members of a likely octahedral coordination sphere could be found. In addition, two Ni²⁺ ions are at site I, eight are at site I′, and five are at site II. Forty six H₃O⁺ ions per unit cell, 24 at site II′ and 22 at site II, each hydrogen bond triply to six rings of the zeolite framework. Each of the 22 H₃O⁺ ions also hydrogen bonds to a H₂O molecule that coordinates to a site III′ Ni²⁺ ion. Six of the eight sodalite cages each contain four H₃O⁺ ions at site II′; the remaining two each contains a tetrahedral orthoaluminate anion at its center. Each tetrahedral face of each orthoaluminate ion is centered by a site I′ Ni²⁺ ion to give two Ni₄AlO₄ clusters. The five site II Ni²⁺ ions each coordinate to a OH⁻ ion. With 46 H₃O⁺ ions per unit cell, the great tendency of hydrated Ni²⁺ to hydrolyze within zeolite X is demonstrated. With a relatively weak single-crystal diffraction pattern, with dealumination of the zeolite framework, and with an apparent decrease in long-range Si/Al ordering likely due to the formation of antidomains, this crystal like others treated with hydrolyzing cations appears to have been damaged by Ni²⁺ exchange and partial dehydration.     

Water vapor sensitivity of nanosized La(Co, Mn, Fe)1−x(Cu, Pd)xO3 perovskites during NO reduction by C3H6 in the presence of oxygen

A series of La(Co, Mn, Fe)_1−x(Cu, Pd)_xO₃ perovskites having high specific surface areas and nanosized crystal domains was prepared by reactive grinding. The solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed desorption (TPD) of O₂, NO + O₂, C₃H₆, in the absence or presence of 5% H₂O, Fourier transform infrared (FTIR) spectroscopy, as well as activity tests towards NO reduction by propene under the conditions of 3000 ppm NO, 3000 ppm C₃H₆, 1% O₂, 0 or 10% H₂O, and 50,000 h⁻¹ space velocity. The objective was to investigate the influence of H₂O addition on catalytic behavior. A good performance (100% NO conversion, 77% N₂ yield, and 90% C₃H₆ conversion) was achieved at 600 °C over LaFe_0.8Cu_0.2O₃ under a dry feed stream. With the exposure of LaFe_0.8Cu_0.2O₃ to a humid atmosphere containing 10% water vapor, the catalytic activity was slightly decreased yielding 91% NO conversion, 51% N₂ yield, and 86% C₃H₆ conversion. A competitive adsorption between H₂O vapor with O₂ and NO molecules at anion vacancies over LaFe_0.8Cu_0.2O₃ was found by means of TPD studies here. A deactivation mechanism was therefore proposed involving the occupation of available active sites by water vapor, resulting in an inhibition of catalytic activity in C₃H₆ + NO + O₂ reaction. This H₂O deactivation was also verified to be strictly reversible by removing steam from the feed.     

Preparation of supported Pt-M catalysts (M = Mo and W) from anion-exchanged hydrotalcites and their catalytic activity for low temperature NO-H2-O2 reaction

The NO-H₂-O₂ reaction was studied over supported bimetallic catalysts, Pt-Mo and Pt-W, which were prepared by coexchange of hydrotalcite-like Mg-Al double layered hydroxides by Pt(NO₂)₄²⁻, MoO₄²⁻, and/or WO₄²⁻ and subsequent heating at 600 °C in H₂. The Pt–Mo interaction could obviously be seen when the catalyst after reduction treatment was exposed to a mixture of NO and H₂ in the absence of O₂. The Pt-HT catalyst showed the almost complete NO conversion at 70 °C, whereas the Pt-Mo-HT showed a negligible conversion. Upon exposure to O₂, however, Pt-Mo-HT exhibited the NO conversion at the lowest temperature of ≥30 °C, compared to ≥60 °C required for Pt-HT. EXAFS/XANES, XPS and IR results suggested that the role of Mo is very sensitive to the oxidation state, i.e., oxidized Mo species residing in Pt particles are postulated to retard the oxidative adsorption of NO as NO₃ and promote the catalytic conversion of NO to N₂O at low temperatures.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Hydrothermal synthesis of Ba(Ti, Sn)O3 fine powders and dielectric properties of the corresponding ceramics

Fine powders of submicron-sized crystallites of BaTiO₃ were prepared at 85–130°C by the hydrothermal method, starting from TiO₂.ξH₂O gel and Ba(OH)₂ solution. The products obtained below 110°C incorporated considerable amounts of H₂O and OH⁻ in the lattice. As-prepared BaTiO₃ is cubic and converts to the tetragonal phase after heat treatment at 1200°C, accompanied by the loss of residual OH⁻ ions. Hydrothermal reaction of SnO₂.ξH₂O gel with Ba(OH)₂ at 150–260°C gives rise to the hydrated phase, BaSn(OH)₆.3H₂O, due to the amphoteric nature of SnO₂.ξH₂O which stabilises Sn(OH)₆²⁻ anions in basic media. On heating in air or releasing the pressure in situ at 260°C, BaSn(OH)₆.3H₂O converts to BaSnO₃ through an intermediate, BaSnO(OH)₄. Solid solutions of Ba(Ti,Sn)O₃ are directly formed from (TiO₂ + SnO₂)..ξH₂O gel up to 35 mol% SnO₂. At higher Sn contents, the hydrothermal products are mixtures of BaSn(OH)₆.3H₂O and BaTiO₃, which on annealing at 1000°C result in monophasic Ba(Ti,Sn)O₃. The sintering characteristics and the dielectric properties of the ceramics prepared out of these fine powders are presented. The dielectric properties of fine-grained Ba(Ti,Sn)O₃ ceramics are explained on the basis of the prevailing diffuse phase transition behaviour.     

Catalytic decomposition of nitrous oxide over calcined cobalt aluminum hydrotalcites

Catalytic decomposition of nitrous oxide has been carried out over calcined cobalt aluminum hydrotalcites of general formula [Co_1−xAl_x(OH)₂[CO₃]_x/2 H₂O where x = 0.25–0.33 at 50 Torr (1 Torr = 133 Pa) initial pressure of N₂O in a static glass recirculatory reactor (130 cc) in the temperature range 150–280°C. All catalysts showed a first order dependence in N₂O without significant oxygen inhibition. The activity increased with an increase in cobalt concentration present in the sample. The catalyst precursor synthesized under low supersaturation (LS) exhibited a higher activity than the precursor synthesized by sequential precipitation (SP) method. The observed trend in the activity is explained based on the surface concentration of cobalt, determined by XPS and matrix effects. Prior to catalytic studies, the fresh and calcined samples were characterized by various physicochemical techniques such as XRD, FT–IR, TG–DSC, TEM (with EDAX) and BET surface area measurements.     

Experimental and microkinetic modeling of steady-state NO reduction by H2 on Pt/BaO/Al2O3 monolith catalysts

Experimental results describing the product distribution during the reduction of NO by H₂ on Pt/Al₂O₃ and Pt/BaO/Al₂O₃ catalysts are presented in the temperature range 30–500 °C and H₂/NO feed ratio range of 0.9–2.5. A microkinetic model that describes the kinetics of NO reduction by H₂ on Pt/Al₂O₃ is proposed and most of the kinetic parameters are estimated from either literature data or from thermodynamic constraints. The microkinetic model is combined with the short monolith flow model to simulate the conversions and selectivities corresponding to the experimental conditions. The predicted trends are in excellent qualitative and reasonable quantitative agreement with the experimental results. Both the model and the experiments show that N₂O formation is favored at low temperatures and low H₂/NO feed ratios, N₂ selectivity increases monotonically with temperature for H₂/NO feed ratios of 1.2 or less but goes through a maximum at intermediate temperatures (around 100 °C) for H₂/NO feed ratios 1.5 or higher. Ammonia formation is favored for H₂/NO feed ratios of 1.5 or higher and intermediate temperatures (100–350 °C) buts starts to decompose at a temperature of 400 °C or higher. The microkinetic model is used to determine the surface coverages and explain the trends in the experimentally observed selectivities.     

三元体系NH4Cl+MgCl2+H2O 323.2 K相平衡研究

采用等温溶解平衡法开展了323.2 K时三元体系NH₄Cl+MgCl₂+H₂O的相平衡研究,测定了平衡固液相组成及密度,并绘制了该三元体系相图。研究发现：该体系323.2 K时有复盐NH₄Cl·MgCl₂·6H₂O生成,相图包含2个共饱点（F₁、F₂）、3条单变量曲线（AF₁、F₁F₂、F₂B）、3个结晶区（NH₄Cl、MgCl₂·6H₂O、NH₄Cl·MgCl₂·6H₂O）。对比该体系273.2、298.2、323.2 K时的相图可知：随着温度升高,NH₄Cl和MgCl₂·6H₂O结晶区变小,NH₄Cl·MgCl₂·6H₂O结晶区变大,同时NH₄Cl·MgCl₂·6H₂O由不相称复盐转变为相称复盐,对应的不相称共饱点转变为相称共饱点。     

Selective oxidation of ammonia over copper-silver-based catalysts

A novel catalyst based on copper-silver was developed to solve the contradiction between the high conversion temperature of Cu-based catalyst and low N₂ selectivity of Ag-based catalyst during selective oxidation of ammonium gas. The Cu-Ag-based catalyst (Cu 5 wt.%-Ag 5 wt.%/Al₂O₃) displayed a relatively low complete conversion temperature (<320 °C) with a high N₂ selectivity (>95%). Increasing loading of Cu and Ag decreases N₂ selectivity. The low N₂ selectivity of Ag-based catalyst is possibly related to the formation of Ag₂O crystals. Improvement of N₂ selectivity of Ag-based catalyst was obtained by doping Cu to decrease crystallized Ag₂O phase. The temperature programmed reaction (TPR) data show that N₂O is the main byproduct of oxidation of ammonia at temperature lower than 200 °C. Two bands of nitrate species at 1541 and 1302 cm⁻¹ were observed on Ag 10 wt.%/Al₂O₃ at the temperature higher than 250 °C, which indicates the formation of NO_x during the selective catalytic oxidation of ammonia. No nitrate species was observed on Cu 10 wt.%/Al₂O₃ and Cu 5 wt.%-Ag 5 wt.%/Al₂O₃, while only one nitrate species (1543 cm⁻¹) existed on Cu 10 wt.%-Ag 10 wt.%/Al₂O₃. We proposed that mixing Ag with Cu inhibited the formation of NO_x during the selective catalytic oxidation of ammonia over Cu-Ag/Al₂O₃.     

Porous structures constructed from [SiMo12O40] and [SiW12O40] Keggin units

Three compounds, K₂(H₂O)₄H₂SiMo₁₂O₄₀ · 7H₂O (1), K₂Na₂(H₂O)₄SiW₁₂O₄₀ · 4H₂O (2), and Na₄(H₂O)₈SiMo₁₂O₄₀ · 6H₂O (3) have been synthesized and structurally characterized by single-crystal X-ray analysis, IR, and thermogravimetry. Compounds 1 and 2 both show the high symmetry trigonal space group P3₂21 and a novel 3D network structure. The Keggin anions [SiM₁₂O₄₀]⁴⁻(M = Mo, W) are linked by potassium or sodium cations to generate hexagon-shaped channels along the c-axis, in which water molecules are accommodated. Compound 3 is tetragonal, space group P4/mnc constructed from [SiMo₁₂O₄₀]⁴⁻ anions and Na ions.     

Combined effect of H2O and SO2 on V2O5/AC catalysts for NO reduction with ammonia at lower temperatures

Combined effect of H₂O and SO₂ on V₂O₅/AC the activity of catalyst for selective catalytic reduction (SCR) of NO with NH₃ at lower temperatures was studied. In the absence of SO₂, H₂O inhibits the catalytic activity, which may be attributed to competitive adsorption of H₂O and reactants (NO and/or NH₃). Although SO₂ promotes the SCR activity of the V₂O₅/AC catalyst in the absence of H₂O, it speeds the deactivation of the catalyst in the presence of H₂O. The dual effect of SO₂ is attributed to the SO₄²⁻ formed on the catalyst surface, which stays as ammonium-sulfate salts on the catalyst surface. In the absence of H₂O, a small amount of ammonium-sulfate salts deposits on the surface of the catalyst, which promote the SCR activity; in the presence of H₂O, however, the deposition rate of ammonium-sulfate salts is much greater, which results in blocking of the catalyst pores and deactivates the catalyst. Decreasing V₂O₅ loading decreases the deactivation rate of the catalyst. The catalyst can be used stably at a space velocity of 9000 h⁻¹ and temperature of 250 °C.     

Synthesis, structure and thermal properties of a novel 3D aluminophosphate UiO-26

The synthesis of a novel 3D aluminophosphate is described. The thermal properties of the material were investigated, and the existence of three high-temperature variants was revealed. The crystal structures of the as-synthesized material (UiO-26-as) and the material existing around 250°C (UiO-26-250) were solved from powder X-ray diffraction data. UiO-26-as with the composition [Al₄O(PO₄)₄(H₂O)]²⁻[NH₃(CH₂)₃NH₃]²⁺ crystallizes in the monoclinic space group P2₁/c (no. 14) with a=19.1912(5), b=9.3470(2), c=9.6375(2) Å and β=92.709(2)°. It exhibits a 3D open framework consisting of connections by PO₄ tetrahedra with AlO₄ tetrahedra, AlO₅ trigonal bipyramids and AlO₅(H₂O) octahedra forming two types of layers stacked along [1 0 0] and connected by Al–O–P bondings. The structure possesses a 1D 10-ring channel system running along [0 0 1], in which doubly protonated 1,3-diaminopropane molecules are located. UiO-26-250 with the composition [Al₄O(PO₄)₄]²⁻[NH₃(CH₂)₃NH₃]²⁺ crystallizes in the monoclinic space group P2₁/c with a=19.2491(4), b=9.27497(20), c=9.70189(20) Å and β=93.7929(17)°. The transformation to UiO-26-250 involves removal of the water molecule which originally is coordinated to aluminum. The rest of the structure remains virtually unchanged. The crystal structures of the two other variants existing around 400 (UiO-26-400) and 600°C (UiO-26-600) remain unknown.     

Changes in free radicals in coal-derived pyrites upon heating in N2, H2, and vacuum: Role of pyrite—pyrrhotite conversion

Through electron spin resonance (e.s.r.) studies, three different kinds of free radicals have been identified in pyrite samples containing coal impurities. Changes in the e.s.r. parameters (g-value, linewidths, and concentration n) of free radicals have been monitored as the coal-derived pyrites are heated in different atmospheres (vacuum, N₂ and H₂) from room temperature to 500°C in 50°C steps for a residence time of 30 min at each temperature. Changes in n (concentration/g) and other parameters begin to occur at 300°C in vacuum, at 200°C in N₂, and at 100°C in H₂ amtospheres. At these temperatures conversion of pyrite to pyrrhotite is also observed to occur. It is argued that the enhancement of n in these samples is related to the conversion mechanism of pyrite to pyrrhotites. The maximum relative increase in n follows the sequence n (vacuum)>n(N₂)>n(H₂). At high temperature n decreases due to recombination of free radicals formed so that at 500°C, all three types of radicals have small but equal concentrations.     

High-quality, oriented and mesostructured organosilica monolith as a potential UV sensor

We synthesized high-quality and oriented periodic mesoporous organosilica (PMO) monoliths through a solvent evaporation process using a wide range of mole ratios of the components: 0.17–0.56 1,2-bis(triethoxysilyl)ethane (BTSE): 0.2 cetyltrimethylammonium chloride (CTACl): 0–1.8 × 10⁻³ HCl: 0–80 EtOH: 5–400 H₂O. X-ray diffraction (XRD) patterns and transmission electron microscopy (TEM) images indicated that the mesoporous channels within the monolith samples were oriented parallel to the flat external surface of the PMO monolith and possessed a hexagonal symmetry lattice (p6mm). The PMO monolith synthesized from a reactant composition of 0.35 BTSE: 0.2 CTACl: 1.8 × 10⁻⁶ HCl: 10 EtOH: 10 H₂O had a pore diameter, pore volume, and surface area – obtained from an N₂ sorption isotherm – of 25.0 Å, 0.96 cm³ g⁻¹ and 1231 m² g⁻¹, respectively. After calcination at 280 °C for 2 h in N₂ flow, the PMO monolith retained monolith-shape and mesostructure. Pore diameter and surface area of the calcined PMO monolith sample were 19.8 Å, 0.53 cm³ g⁻¹ and 1368 m² g⁻¹, respectively. We performed ²⁹Si and ¹³C CP MAS NMR spectroscopy experiments to confirm the presence of Si–C bonding within the framework of the PMO monoliths. We investigated the thermal stability of the PMO monoliths through thermogravimetric analysis (TGA). In addition, rare-earth ions (Eu³⁺, Tb³⁺ and Tm³⁺) were doped into the monoliths. Optical properties of those Eu³⁺, Tb³⁺ and Tm³⁺-doped PMO monoliths were investigated by photoluminescence (PL) spectra to evaluate their potential applicability as UV sensors.     

Selective catalytic reduction of N2O and NOx in a single reactor in the nitric acid industry

The nitric acid industry is a source of both NO_x and N₂O. The simultaneous selective catalytic reduction of both compounds using propane as a reductant has been investigated. A stacked catalyst bed with first a Co-ZSM-5 catalyst and second a Pd/Fe-ZSM-5 catalyst gives >80% conversion of N₂O and NO_x above 300 °C at atmospheric pressure. At 4 bar absolute pressure (bara) the Co-ZSM-5 DeNO_x catalyst shows higher NO_x and propane conversion. This leaves not enough propane for the Pd/Fe-ZSM-5 DeN₂O catalyst, which causes a ‘dip’ in N₂O conversion. Reducing the space velocity (SV) of the first catalyst bed secures high NO_x and N₂O conversions from 300 °C and up at 4 bara.     

Ceria-based oxides as supports for LaCoO3 perovskite; catalysts for total oxidation of VOC

Supported LaCoO₃ perovskites with 10 and 20 wt.% loading were obtained by wet impregnation of different Ce_1−xZr_xO₂ (x = 0–0.3) supports with a solution prepared from La and Co nitrates, and citric acid. Supports were also prepared using the “citrate method”. All materials were calcined at 700 °C for 6 h and investigated by N₂ adsorption at −196 °C, XRD and XPS. XRD patterns and XPS measurements evidenced the formation of a pure perovskite phase, preferentially accumulated at the outer surface. These materials were comparatively tested in benzene and toluene total oxidation in the temperature range 100–500 °C. All catalysts showed a lower T₅₀ than the corresponding Ce_1−xZr_xO₂ supports. Twenty weight percent LaCoO₃ catalysts presented lower T₅₀ than bulk LaCoO₃. In terms of reaction rates per mass unit of perovskite calculated at 300 °C, two facts should be noted (i) the activity order is more than 10 times higher for toluene and (ii) the reverse variation with the loading as a function of the reactant, a better activity being observed for low loadings in the case of benzene. For the same loading, the support composition influences drastically the oxidative abilities of LaCoO₃ by the surface area and the oxygen mobility.     

H4SiW12O40-catalyzed oxidation of nitrobenzene in supercritical water: kinetic and mechanistic aspects

The catalytic effect of a heteropolyacid, H₄SiW₁₂O_40, on nitrobenzene (20 and 30 μM) oxidation in supercritical water was investigated. A capillary flow-through reactor was operated at varying temperatures (T=400–500 °C; P=30.7 MPa) and H₄SiW₁₂O₄₀ concentrations (3.5–34.8 μM) in an attempt to establish global power-law rate expressions for homogenous H₄SiW₁₂O₄₀-catalyzed and uncatalyzed supercritical water oxidation. Oxidation pathways and reaction mechanisms were further examined via primary oxidation product identification and the addition of various hydroxyl radical scavengers (2-propanol, acetone, acetone-d₆, bromide and iodide) to the reaction medium. Under our experimental conditions, nitrobenzene degradation rates were significantly enhanced in the presence of H₄SiW₁₂O₄₀. The major differences in temperature dependence observed between catalyzed and uncatalyzed nitrobenzene oxidation kinetics strongly suggest that the reaction path of H₄SiW₁₂O₄₀-catalyzed supercritical water oxidation (average activation E_a=218 kJ/mol; k=0.015–0.806 s⁻¹ energy for T=440–500 °C; E_a=134 kJ/mol for the temperature range T=470–490 °C) apparently differs from that of uncatalyzed supercritical water oxidation (E_a=212 kJ/mol; k=0.37–6.6 μM s⁻¹). Similar primary oxidation products (i.e. phenol and 2-, 3-, and 4-nitrophenol) were identified for both treatment systems. H₄SiW₁₂O₄₀-catalyzed homogenous nitrobenzene oxidation kinetics was not sensitive to the presence of OH√ scavengers.     

Reaction and characterization studies of an industrial Cr-free iron-based catalyst for high-temperature water gas shift reaction

Activity and stability of an industrial Cr-free iron-based catalyst (NBC-1) for high-temperature water gas shift (WGS) reaction were studied in a fixed-bed reactor under 350 °C, 1 atm, H₂O:gas = 1:1 and 3000 h⁻¹ (dry-gas basis). Physical properties of the NBC-1 catalyst before and after the WGS reaction, the desorption behavior of H₂O, CO, CO₂ and H₂, and surface reaction over the catalyst were characterized by BET, X-ray diffraction (XRD), Mössbauer emission spectroscopy (MES), temperature programmed desorption (TPD) and temperature programmed surface reaction (TPSR). The NBC-1 catalyst is active and has excellent thermo-stability even after pretreatment at a high temperature of 530 °C. Its activity and thermo-stability are comparable to those of an UCI commercial Fe-Cr catalyst, C12-4. XRD and MES studies show that iron in the fresh NBC-1 catalyst is present as γ-Fe₂O₃, most of which is converted to Fe₃O₄ during reduction and reaction. Results of TPD demonstrate that adsorbed CO₂ and CO cannot exist on the NBC-1 surface beyond the temperature of 300 °C while higher temperatures (>400 °C) are required to completely desorb H₂O. A redox mechanism of WGS on the NBC-1 surface is proposed based on the TPD and TPSR observations.