弱限制MMI型光功分器

本文采用导模数值计算法对MMI(多模干涉)型光功分器SIE干涉区内的导模进行计算并对输出波导位置进行优化,证明在一定条件的弱限制下器件的插入损耗和输出均匀度均超过强限制的情况,说明MMI型光功分器的制作可以采用方便的湿法刻蚀,在器件成本降低的同时其精度也得到改善.     

MMI阵列波导光栅复用/解复用器的研制

详细分析了基于自镜像效应的MMI DMUX器件的基本工作原理,在此基础上,在SOI材料上完成了对8信道MMI DMUX的具体设计.该器件的输入、输出单模波导采用Soref的大截面脊形光波导理论进行优化设计,最后获得了当输入、输出单模波导宽度为5μm,SIE多模波导宽度和长度分别为72μm和6313.4μm时,该器件对8信道波长的隔离度均在35dB以上,且理论传输损耗＜0.18dB.     

离子交换制作0.85μm MMI光功分器的仿真研究

提出了利用离子交换技术制作多模干涉(MMI)型光功分器的设计方法.以1×8MMI光功分器为例,采用导模传输分析法分析了器件基本原理,对离子交换制作波导的折射率分布进行了讨论.针对工作波长为0.85μm的1×8MMI光功分器结构参数进行了设计,对器件输出特性、各项技术指标、离子交换决定的折射率差Δn对器件性能的影响均进行了BPM仿真,结果表明:利用离子交换方法制作MMI型光功分器,设计指标可达到均匀性约0.009dB、平均插入损耗约9.111dB和最大插入损耗约9.116dB,均优于现有器件的指标.     

基于聚合物多模干涉器的大容差相干光混频器

根据多模干涉器(MMI,multimode interferome ter)的自映像效应,设计了基于2×4MMI 的聚合物相干光混频器,优化光混频器结构参数;采用模式转换设计解 决多模波导的 自映像与单模波导模式失配的问题,从而进一步提高其性能。仿真结果表明,优化后的光混 频器其传输损耗 小于6.3dB,传输不均衡性小于1dB,相位误差小于1°,并且MMI长 度与宽度的设计容差分别达到40μm 和0.5μm。根据设计制备了聚合物光混频器,通过实验表征了此光 混频器的传输性能。在C波段下的测量 结果表明,其传输损耗小于10dB,不均衡性在0.5～1. 5dB之间,相位误差小于10°, 而达到这些性能的MMI长度与宽度的器件容差分别为25μm和0.5μm,均大于制备过程中0.1μm的工艺容差。测 量结果与理论模拟结果基本吻合。本文的聚合物光混频器成本低、容差高,对实现高集成度 相干接收机具有实际意义。     

玻璃基多模波导光功分器的研制

利用Ag+-Na+电场辅助玻璃基离子交换技术制作了低损耗的掩埋多模波导,并在此基础上研制了多模波导光功分器.测试分析了多模波导和光功分器的损耗和偏心率特性.所研制的多模直波导传输损耗小于0.1dB/cm,所制作的1×2的多模波导光功分器附加损耗小于1.3 dB.     

MMI阵列波导光栅复用/解复用器的研制

详细分析了基于自镜像效应的 MMI DMUX器件的基本工作原理 ,在此基础上 ,在 SOI材料上完成了对 8信道 MMI DMU X的具体设计 .该器件的输入、输出单模波导采用 Soref的大截面脊形光波导理论进行优化设计 ,最后获得了当输入、输出单模波导宽度为 5 μm,SIE多模波导宽度和长度分别为 72 μm和 6 313.4μm时 ,该器件对8信道波长的隔离度均在 35 d B以上 ,且理论传输损耗 <0 .18d B.     

基于SOI的2×2 MMI耦合器的设计

设计了一种可用于阵列波导光栅(AWG)解调集成微系统的绝缘体上硅(SOI)基2×2多模干涉(MMI)耦合器,用光束传播法(BPM)对MMI耦合器进行了模拟。耦合器输入/输出波导采用倒锥形,多模干涉区尺寸为6μm×57μm。在TE偏振中心波长为1.55μm时,器件附加损耗为0.46dB,不均匀性为0.06dB。在1.49～1.59μm波长范围内耦合器的附加损耗小于1.55dB。仿真结果表明所设计的2×2MMI耦合器体积小、附加损耗低、波长响应范围宽、分光均匀,符合片上集成系统的要求。     

MMI型1.31／1.55umGaAs波分复用／解复用器的研制

利用多模波导的自镜像原理,分析设计了一种能直接与单模光纤相耦合的具有最小循环比的1031/1.55um波长的GaAs/G aAlAs波分复用／解复用器。该器件的输入、输出单模波导和SIE多模波导采用离散谱折射率法进行了优化设计,最后获得了当输入、输出单模波导宽为3um、SIE多模波导宽度和最佳耦合长度分别为18um和5602.8um时,该器件的1.31um和1.55um两个波长的隔离度均在70dB以上,且传输损耗小于0.1 dB.     

MMI型1.31/1.55 μm GaAs波分复用/解复用器的研制

利用多模波导的自镜像原理,分析设计了一种能直接与单模光纤相耦合的具有最小循环比的1.31/1.55 μm波长的GaAs/GaAlAs波分复用/解复用器。该器件的输入、输出单模波导和SIE多模波导采用离散谱折射率法进行优化设计,最后获得了当输入、输出单模波导宽为3 μm、SIE多模波导宽度和最佳耦合长度分别为18 μm和5 602.8 μm时,该器件对1.31 μm和1.55 μm两个波长的隔离度均在70 dB以上,且传输损耗小于0.1 dB。     

基于MMI的聚合物1×16光功分器的设计及飞秒激光制备

高传输损耗和器件尺寸是限制光通信系统性能的关键问题,为此以光束传播法(BPM)设计仿真、利用飞秒超快加工技术制备了基于多模干涉耦合器(MMI)的聚合物1×16光功分器,器件尺寸小于22000μm。仿真结果表明平均插入损耗小于23dB,均匀性1.27dB。测试在1550nm波段,1×16光功分器平均插入损耗小于23dB,均匀性1.48dB。基于SU8胶材料仿真了用于光电电路板垂直耦合的光波导结构,利用时域有限差分法(FDTD)分析空间位置偏差对光纤与45°微反射镜的耦合效率影响,得到最佳耦合位置和最大耦合效率86.1%。结果表明器件具有易制备,较低的制备容差敏感度和结构紧凑的优点,符合光电集成和批量生产要求,对光分路器的设计和生产工艺有一定的参考价值。     

聚对苯撑苯并双(口恶)唑发光及其器件制备

采用光谱技术,研究了聚对苯撑苯并双(口恶)唑(PBO)溶液的光敏发光特性,并用相对法估算出溶液发光效率在50%范围.结合光谱技术、半导体电学和电化学等研究手段,具体研究了以PBO为发光层的单层电致发光器件,研究结果显示,电致发光与薄膜的光致发光有具有相同的发光中心,峰值位于510 nm左右.同时发现,由于存制备过程中不同处理条件使得不同厚度薄膜残留的掺杂物质浓度不同,从而引起薄膜的导电性的不同.使得器件的阈值场强随PBO厚度的减小而逐渐增加.     

系统级封装新型埋入式电源滤波结构的研究

在高密度小尺寸的系统级封装(SiP)中,对供电系统的完整性要求越来越高,多芯片共用一个电源网路所产生的电压抖动除了会影响到芯片的正常工作,还会通过供电网路干扰到临近电路和其他敏感电路,导致芯片误动作,以及信号完整性和其他电磁干扰问题.这种电压抖动所占频带相当宽,几百MHz到几个GHz的中频电源噪声普通方法很难去除.结合埋入式电容和电源分割方法的特点,提出一种新型高性能埋入式电源低通滤波结构直接替代电源/地平面.研究表明,在0.65～4GHz的频带内隔离深度可达-40～75 dB,电源阻抗均在0.25ohm以下,实现了宽频高隔离度的高性能滤波作用.分别用电磁场和广义传输线两种仿真器模拟,高频等效电路模型分析这种低通滤波器的工作原理以及结构对隔离性能的影响,并进行了实验验证.     

Emerging interconnects: a state-of-the-art review and emerging solutions

Aluminium was a primary material for interconnection in integrated circuits (ICs) since their inception. Later, copper was introduced as interconnect material which has better metallic conductivity and resistance to electromigration. As the aggressive technology scaling continues, the copper resistivity increased because of size effects, which causes increase in delay, power dissipation and electromigration. The need to reduce the resistor-capacitor??????? delay, dynamic power utilisation and the crosstalk commotion is as of now the fundamental main impetus behind the presentation of new materials. The purpose of this paper is to do a survey of interconnect material used in IC from introduction of ICs to till date. This paper studies and reviews new materials available for interconnect application which are optical interconnects, carbon nanotube (CNT), graphene nanoribbons (GNRs) and silicon nanowires which are alternatives to copper. While doing a survey of interconnect material, it is found that multiwalled CNTs, multilayer GNR and mixed CNT bundles are promising candidates and are ultimate choice that can strongly address the problems faced by copper but on integration basis copper would last for coming years.     

Arsenic deposition as a precursor layer on silicon (211) and (311) surfaces

We investigate the properties of arsenic (As) covered Si(211) and Si(311) surfaces by analyzing data from x-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED) images. We then create a model using total surface energy calculations. It was found that both Si(211) and Si(311) had 0.68±0.08 surface As coverage. Si(211) had 0.28±0.04 Te coverage and Si(311) had 0.24±0.04 Te coverage. The Si(211) surface replaces the terrace and trench Si atoms with As for a lower surface energy, while the Si edge atoms form dimers. The Si(311) surface replaces all terrace atoms and adsorbs an As dimer every other edge site. These configurations imply an improvement in the mean migration path from the bare silicon surface by allowing the impinging atoms for the next epitaxial layer, tellurium (Te), to bind at every other pair of edge atoms, and not the step terrace sites. This would ensure a nonpolar, B-face growth.     

光子晶体微腔发光二极管

光子晶体微腔因其具有增强自发辐射、定向输出和单模工作的能力而受到广泛关注。介绍了光子晶体微腔发光二极管的基本原理、设计、特性、制作及其典型器件。     

用于单光子TOF测量的时间-幅度变换器

基于新型共源共栅电流源的积分方法,设计了一种用于单光子飞行时间(TOF)测量的时间-幅度变换器(TAC)。该方法有效简化了TAC电路结构,减小了TAC占用面积,显著提高了TOF的满量程范围(FSR)。采用0.18 μm标准CMOS工艺设计。集成TAC的单光子探测器像素单元的填充因子可达到26.8%。后仿真结果表明,该TAC在120 ns的FSR内具有230 ps的定时分辨率,微分非线性(DNL)低于0.05 LSB,积分非线性(INL)低于1.1 LSB。蒙特卡洛仿真表明,512个TAC像素间的不均匀性低于0.5 %。该TAC非常适用于高密度时间相关的单光子计数(TCSPC)探测器阵列。     

Comparative study of maximum power point tracking techniques for hybrid renewable energy system

The power generation demand is increasing day-by-day throughout the world, therefore, the use of hybrid systems becomes a significant solution. The hybrid renewable energy system (HRES) is used for delivering power in various regions in order to overcome intermittence of wind and solar resources. Because of increasing environmental problems, for example, greenhouse gas emission and energy cost have interested novel research into substitute methods in favour of electrical power generation. Maximum Power Point Tracking (MPPT) control method is a vast deal of novel research used for enhancing the efficiency of HRES. The authors have revealed that the hybrid techniques i.e. Global MPPT, fuzzy-neuro systems, Adaptive Neuro-Fuzzy Inference System (ANFIS), Perturbed and Observe (P&O) + Adaptive Neural Network (ANN) etc. can provide best results as compared to other MPPT control methods. This paper offering a state of art review of MPPT control techniques for HRES.     

Joint estimation of TOA and DOA in IR-UWB system using a successive propagator method

Impulse radio ultra-wideband (IR-UWB) ranging and positioning require accurate estimation of time-of-arrival (TOA) and direction-of-arrival (DOA). With receiver of two antennas, both of the TOA and DOA parameters can be estimated via two-dimensional (2D) propagator method (PM), in which the 2D spectral peak searching, however, renders much higher computational complexity. This paper proposes a successive PM algorithm for joint TOA and DOA estimation in IR-UWB system to avoid 2D spectral peak searching. The proposed algorithm firstly gets the initial TOA estimates in the two antennas from the propagation matrix, then utilises successively one-dimensional (1D) local searches to achieve the estimation of TOAs in the two antennas, and finally obtains the DOA estimates via the difference in the TOAs between the two antennas. The proposed algorithm, which only requires 1D local searches, can avoid the high computational cost in 2D-PM algorithm. Furthermore, the proposed algorithm can obtain automatically paired parameters and has better joint TOA and DOA estimation performance than conventional PM algorithm, estimation of signal parameters via rotational invariance techniques algorithm and matrix pencil algorithm. Meanwhile, it has very close parameter estimation to that of 2D-PM algorithm. We have also derived the mean square error of TOA and DOA estimation of the proposed algorithm and the Cramer-Rao bound of TOA and DOA estimation in this paper. The simulation results verify the usefulness of the proposed algorithm.     

超宽带脉冲信号的光学生成方法研究

近年来超宽带(UWB)通信技术迅猛发展,在测量、雷达技术、民用和军事无线通信中有着重要的应用,UWB-over-fiber技术已经成为目前研究的热点,其中就包括UWB脉冲信号的产生方法。区别于传统的电子学方法,光子学产生方法不受电子瓶颈制约,可以实现很高的带宽,并且具有抗电磁干扰、重量轻、结构紧凑的优点。通过对比国内外本领域研究成果,讨论及总结了以下三种原理的UWB脉冲信号的光学生成方法:1)相位调制-强度调制转换(PM-IM);2)半导体光放大器(SOA)的非线性效应;3)频谱塑形和色散所致频域-时域映射,然后对各种方案进行了对比分析。     

多孔硅发光机制的分析

从量子力学的基本理论出发讨论了量子限制效应，推导出多孔硅有效禁带宽度增量并用量子限制效应和表面态及其物质在发光中作用的理论解释了ＰＳ光致发光的实验现象。