Thermal and dynamic mechanical behavior of poly(vinyl chloride)/wood flour composites

Thermal and dynamic mechanical behaviors of wood plastic composites made of poly vinyl chloride (PVC) and surface treated, untreated wood flour were characterized by using differential scanning calorimetry and dynamic mechanical analysis. Glass transition temperature (T_g) of PVC was slightly increased by the addition of wood flour and by wood flour surface treatments. Heat capacity differences (ΔC_p) of composites before and after glass transition were markedly reduced. PVC/wood composites exhibited smaller tan δ peaks than PVC alone, suggesting that less energy was dissipated for coordinated movements and disentanglements of PVC polymer chains in the composites. The rubbery plateaus of storage modulus (E′) curves almost disappeared for PVC/wood composites in contrast to a well defined plateau range for pure PVC. It is proposed that wood flour particles act as “physical crosslinking points” or “pinning centers” inside the PVC matrix, resulting in the absence of the rubbery plateau and high E′ above T_g. The mobility of PVC chain segments were further retarded by the presence of surface modified wood flour. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties of poly(vinyl chloride)/wood flour/glass fiber hybrid composites

Short glass fibers were added to poly(vinyl chloride) (PVC)/wood flour composites as reinforcement agents. Unnotched and notched impact strength of PVC/wood flour/glass fiber hybrid composites could be increased significantly without losing flexural properties by adding type L glass fibers and over 40% of PVC. There was no such improvement when using type S glass fiber. The impact strength of hybrid composites increased along with the increment of the type L glass fiber content at a 50% PVC content. At high PVC contents, impact fracture surfaces were characterized by wood particle, glass fiber breakage and pullout, whereas interfacial debonding was the dominant fracture mode at higher filler concentrations. The significant improvement in impact strength of hybrid composites was attributed to the formation of the three‐dimensional network glass fiber architecture between type L glass fibers and wood flour.     

Free volume microprobe studies on poly(methyl methacrylate)/poly(vinyl chloride) and poly(vinyl chloride)/polystyrene blends

Blends of Poly(methyl methacrylate) (PMMA)/Poly(vinyl chloride) (PVC) and Poly(vinyl chloride) (PVC)/Polystyrene (PS) of different compositions were prepared by solution casting technique. The blends were characterized using Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR), and Positron Lifetime Spectroscopy. DSC data were found to be inadequate to describe whether PMMA/PVC blends are miscible or not, possibly because of the small gap in their glass transition temperatures. On the other hand, PVC/PS blends were clearly found to be immiscible by DSC. FTIR results for PMMA/PVC indicate the possible interactions between the carbonyl group of PMMA and α‐hydrogen of PVC. Free volume data derived from Positron lifetime measurements showed that the PMMA/PVC blends to be miscible in low PVC concentration domain. For the first time, the authors have evaluated the hydrodynamic interaction parameter α, advocated by Wolf and Schnell, Polymer, 42, 8599 (2001), to take into account the friction between the component molecules using the free volume data. This parameter (α) has a high value (?57) at 10 wt% of PVC, which could be taken to read miscibility for PMMA/PVC blends to be high. In the case of PVC/PS blends, the positron results fully support the DSC data to conclude the blends to be immiscible throughout the range of concentration. As expected, the hydrodynamic interaction parameter α does not show any change throughout the concentration in PVC/PS blends, further supporting the idea that α is another suitable parameter in the miscibility study of polymer blends. POLYM. ENG. SCI., 46:1231–1241, 2006. © 2006 Society of Plastics Engineers     

Structure and properties of poly(vinyl chloride)/montmorillonite composites produced from plastisols

Poly(vinyl chloride) (PVC)/montmorillonite nanocomposites were prepared from plastisols. The concentrations of plasticizer and montmorillonite were varied. The composites were characterized by both X‐ray diffraction and transmission electron microscopy, which indicated that intercalated nanocomposites were prepared, but that the distribution of clay was not uniform on the nanoscale. Plasticizer migration was found to decrease with increasing concentration of clay and could be reduced by 25% when 3 wt% of Cloisite 30B was added in formulations containing 100 phr (parts by weight per hundred parts of resin) of plasticizer. Montmorillonite was found to reduce the tensile properties of PVC, especially when the plasticizer concentration was low, i.e., 50 phr. J. VINYL ADDIT. TECHNOL., 22:140–145, 2016. © 2014 Society of Plastics Engineers     

Processing thermal stability and degradation kinetics of poly(vinyl chloride)/montmorillonite composites

Thermal stability of polyvinyl chloride (PVC) based montmorillonite composites with either sodium montmorillonite (MMT) or alkyl ammonium ion modified montmorillonite (OMMT) were investigated by thermogravimetric analysis. The apparent activation energies associated with the first thermal degradation stage were calculated by the methods of Flynn–Wall–Ozawa and Kissinger in nitrogen atmosphere at several different heating rates. The processing thermal stability of PVC and PVC/MMT(OMMT) composites was also discussed. Increase of mixing torque did not result in a larger intercalation extent of PVC on MMT; instead, it unexpectedly induced discoloration of PVC and then deteriorated the processing stability, especially in the presence of OMMT. The apparent activation energies in the first thermal degradation stage exhibited little difference among PVC, PVC/MMT, and PVC/OMMT composites, and the kinetic compensation effect of S_p^* kept a constant value, indicating that the thermal stability and thermal degradation mechanism of PVC were not affected by the presence of either MMT or OMMT, although the processing discoloration of PVC is observed for PVC/OMMT composite. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1521–1526, 2004     

Rheological and mechanical properties of poly(vinyl chloride)/chlorinated poly(vinyl chloride) miscible blends

The properties of poly(vinyl chlorlde)/ehlorinated poly(vinyl chloride) (61.6 percent C1) blends, prepared by melt and solution blending, were measured by various tests. Based on the chlorinated poly(vinyl chloride) (CPVC) composition, percent chlorine, and mole percent CC1₂ groups, these blends were expected to show intermediate properties between miscible and immiscible systems. Indicative of miscible behavior were the single glass transition temperatures over the entire composition range for both melt and solution blended mixtures. A single phase was also indicated by transmission electron microscopy. However, the yield stress showed a minimum value less than either of the pure components in the 50 to 75 percent CPVC range, which is characteristic of two-phased systems. Specific volume, glass transition temperature, and heat distortion temperature were linear with binary composition. The storage modulus showed a small maximum, suggesting a weak interaction between the two miscible polymers. Heats of melting for the residual PVC crystallinity were also less than expected from linear additivity. At 160°C and 210°C, the logarithm of the complex viscosity was essentially linear with volume fraction of CPVC, except for a very slight decrease in the 50 to 75 percent CPVC range, which may have been a result of lower crystallinity. At 140°C, the complex viscosity of the CPVC was less than that of PVC owing to the higher crystallinity of the latter. The viscosities were similar at 160°C, but at 210°C, where most of the crystallites had melted, the complex viscosity of the CPVC was higher because of its higher glass transition temperature.     

Preparation and characterization of poly(vinyl chloride)/virgin and treated sisal fiber composites

Mechanical property changes, thermal stability, and water absorption capacity of poly(vinyl chloride) (PVC)/sisal fiber composites were assessed with respect to the effect of maleic anhydride chemical treatments of the sisal fiber, for five different sisal fiber contents, varying from 0 to 30% by weight in the composite. The composites prepared with the untreated sisal exhibited higher tensile modulus and hardness than the unloaded resin, while elongation and tensile strength were reduced. The deterioration in the mechanical properties of PVC blended with sisal fiber is attributed to the presence of moisture, interfacial defects at the fiber and polymer interface, and fiber dispersion in the PVC matrix. The amount of absorbed water is a function of the amount of fiber in the composite (F0 = 0 phr, F5 = 0.77 phr, and F20 = 4.83 phr). The comparison of the results of characterization of F5, F20, and F30 formulations prepared with the untreated fibers and the treated ones showed a reduction in absorbed water after the chemical treatment of fiber with maleic anhydride (F0 = 0 phr, F5 = 0.28 phr, and F20 = 2.99 phr), thus improving the mechanical properties of composites prepared with the treated sisal. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3630–3636, 2007     

Miscibility in poly(vinyl chloride)/chlorinated poly(vinyl chloride) blends,and blends of different chlorinated poly(vinyl chlorides)

Blends of poly(vinyl chloride) with chlorinated poly(vinyl chloride) (PVC), and blends of different chlorinated poly(vinyl chlorides) (CPVC) provide an opportunity to examine systematically the effect that small changes in chemical structure have on polymer-polymer miscibility. Phase diagrams of PVC/CPVC blends have been determined for CPVC's containing 62 to 38 percent chlorine. The characteristics of binary blends of CPVC's of different chlorine contents have also been examined using differential calorimetry (DSC) and transmission electron microscopy. Their mutual solubility has been found to be very sensitive to their differences in mole percent CCl₂ groups and degree of chlorination. In metastable binary blends of CPVC's possessing single glass transition temperatures (T_g) the rate of phase separation, as followed by DSC, was found to be relatively slow at temperatures 45 to 65° above the T_g of the blend.     

Thermal stability of poly(vinyl chloride)/polyurethane blends

The thermal stability of poly(vinyl chloride) (PVC) and thermoplastic polyurethane (PU) blends has been studied in this work. It has been found that the PVC/PU blends possess lower thermal stability than unmodified PVC. No effect of the structure of polyurethanes or their content on the stability of PVC/PU system has been found.     

聚乙烯醇/微纤化纤维素复合微发泡材料的制备

通过溶液浇铸法制备了聚乙烯醇(PVOH)/微纤化纤维素(MFC)复合薄膜材料,以超临界二氧化碳(scCO₂)为物理发泡剂,采用间歇式降压法制备了一系列PVOH/MFC复合微发泡材料,主要讨论了在没有水分的影响下,不同发泡温度和时间以及MFC含量对PVOH/MFC复合微发泡材料的泡孔形貌、泡孔尺寸和泡孔密度的影响;同时,也对MFC的分散性和PVOH/MFC复合材料的流变性能和热性能对发泡行为的影响进行了研究。实验结果表明,均匀分散在PVOH基体中的MFC作为异相成核剂提高了气孔成核能力,且随着MFC含量的增加,泡孔尺寸降低,泡孔密度增大;并研究了发泡温度对PVOH/MFC复合材料的发泡形貌的影响,获得最优发泡温度。     

A study of the synergism of poly(vinyl chloride)/polyether-ester blends

The synergism between blends of poly(vinyl chloride), PVC, and a polyether-ester elastomer, COPE, was investigated. Previous research indicated that blends of these two polymers produced synergistic results in the melt index and Izod impact properties of the system. This research confirmed the increased flow properties of the blends using melt index, capillary rheometer, and dynamic mechanical analysis. The synergism was found to be shear rate dependent and an additive relationship was approached at high shear rates. Differential scanning calorimetry showed that the blends were immiscible. This suggested that phase separation was the cause of the synergism in the flow properties and that elongation of the COPE domains most likely produced the shear rate dependency of the blend synergism. The phase separation would also have produced the improvement in the Izod impact properties of the blends.     

Behavior of flexible poly(vinyl chloride)/poly(hydroxybutyrate valerate) blends

Blends of flexible poly(vinyl chloride) (PVC) and a poly(hydroxybutyrate valerate) (PHBV) copolymer were prepared and characterized with different techniques. The tensile strength of PVC did not show a marked reduction at PHBV concentrations up to 50 phr, despite a lack of miscibility between the two polymers. The crystallization of the PHBV copolymer was markedly hindered by the presence of PVC, as calorimetric results revealed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of moisture content on mechanical properties,thermal and structural stability and extrudate texture of poly(vinyl chloride)/wood sawdust composites

Mechanical properties and thermal and structural changes of poly(vinyl chloride) (PVC)/wood sawdust composites were assessed with respect to the effect of moisture content, varying from 0.33 to 3.00 % by weight in the composite, for three different wood sawdust contents. The swell ratio and texture characteristics of the composite extrudates were also evaluated. Unique explanations were given to describe changes in the composite properties in terms of molecular interactions between PVC, cellulosic sawdust and moisture, such as dipole–dipole interactions, interfacial defects and bonding, fibre swelling, and moisture evaporation. The results suggest that at low moisture content the tensile modulus decreased and elongation at break of the composites increased with moisture content, the effect being reversed for high moisture content. Tensile strength decreased with increasing moisture content up to 1–2 %, and then unexpectedly increased at higher moisture contents. The effect of moisture content on flexural properties of the composite was similar to that on tensile properties. Impact strength of the composites was considerably improved with moisture content at low sawdust contents (16.7 wt%), and was independent of the moisture content at higher sawdust contents (28.6 and 37.5 wt%). A decrease in decomposition temperature with an increase in polyene content was evidenced with increasing moisture content, while the glass transition temperature did not change with varying moisture content. The extrudate swell ratio increased with the shear rate but remained unaffected by moisture content. The bubbling and peeling‐off in the composite extrudate occurred as a result of the evaporation of water molecules and the application of a high shear rate. Copyright © 2004 Society of Chemical Industry     

Properties and structure of poly(vinyl alcohol)/silica composites

The relationships between the properties and structure are discussed for poly(vinyl alcohol)(PVA)/silica composites prepared through the sol‐gel process. The composites became stiff and brittle with increasing the silica content. The properties of the composites were changed drastically at around the composition of PVA/silica = 70/30 wt %. For example, there was no large change in the Young's modulus above 30 wt % of silica content (Pure PVA: 31.8 MPa, silica 30%: 52.6 MPa, silica 50%: 55.2 MPa). Consequently, it was considered that the three‐dimensional network structure of silica could be formed in the composite with more than 30 wt % of silica in PVA. From this behavior, it could be considered that the crystal growth of PVA was remarkably inhibited by silica network. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 133–138, 1999     

Modification of poly(vinyl chloride). XIX. Electroplating of poly(vinyl chloride)

As a preliminary treatment in the PVC-electroplating procedure, treatment with dimethylformamide followed by sensitization leads to a finely roughened and a highly hydrophilic surface with reducing power. This is caused by the formation of an ionic complex compound between dimethylformamide and tin(II) chloride absorbed in the PVC surface. A much more finely and deeply etched surface which exhibits higher adhesion through the mechanical interlocking effect is obtained with the PVC blends containing the plasticizer with a low value of interaction parameter and with a solubility parameter approximate to that of PVC. Adhesion of the metal layer to the PVC surface thus obtained is improved about 1.5 times by thermal aging at 120°C for 20 min.     

Study on thermal,mechanical and morphological properties of recycled poly(vinyl chloride)/fly ash composites

The present study deals with the development of composite materials utilizing recycled poly(vinyl chloride) (r‐PVC) recovered from waste electrical and electronic materials and waste fly ash obtained from thermal power plants. The effect of the incorporation of fly ash on the mechanical, thermal and morphological properties of the r‐PVC matrix was studied. The primary characterization of r‐PVC and fly ash was done employing FTIR, EDX, particle size analysis and XRD analysis. Subsequently, fly ash with a particle size of approximately 9.29 μm was incorporated within the r‐PVC matrix. Composite sheets were prepared using a melt blending process followed by compression moulding. The mechanical test revealed an increase in the tensile strength and elongation at break of the r‐PVC/fly ash composite up to 30 wt% loading of fly ash beyond which there was a decrease in the tensile strength. The impact strength, however, decreased with increasing fly ash content in the r‐PVC matrix. The morphological properties of the composites showed a good distribution of the filler within the recycled matrix. The thermal properties of r‐PVC also improved with the incorporation of fly ash which was revealed from DSC and TGA studies. The water absorption test showed an increase in water uptake with the addition of fly ash in the r‐PVC matrix. © 2020 Society of Chemical Industry     

Some viscoelastic porperties of poly(vinyl chloride)/dioctyl phthalate systems

The viscosty and the recoverable shear compliance of poly(viny chloride)/dioctyl phthalate systems are studied at different temperatures and concentrations. The recoverable shear compliance is determined by the method of the stress relaxation after cessation of flow in a Couette flow viscosimeter. The results show the existence of a concentration dependent critical temperature T_c which separates two different flow regions.     

Comparison of the toughening mechanisms of poly(vinyl chloride)/chlorinated polyethylene and poly(vinyl chloride)/acrylonitrile–butadiene–styrene copolymer blends

In this study, the influence of chlorinated polyethylene (CPE) and acrylonitrile–butadiene–styrene copolymer (ABS) on the mechanical properties of poly(vinyl chloride) (PVC)/CPE and PVC/ABS hybrids were examined. The experimental results show that the toughness of the hybrids could be modified greatly by the introduction of CPE or ABS. The microstructure and impact surfaces of the blends were investigated by scanning electron microscopy and transmission electron microscopy. ABS dispersed in the form of particles or agglomerates in the PVC matrix, and CPE tended to disperse as a net structure. In the tensile test, ABS initiated crazes as stress concentrators to toughen the PVC matrix, whereas CPE, with the PVC matrix together, caused a yield deformation by shear stress to form a shear band. The formation of crazes and shear bands benefited the toughening of PVC, but to the different extent. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 916–924, 2003     

Modification of poly(vinyl chloride). XXXIV. Crosslinked poly(vinyl chloride) via paste-processing

A novel PVC-crosslinking technique using 6-dibutylamino-1,3,5-triazine-2,4-dithiol (DB) was applied for a paste processing to produce a crosslinked PVC product. The paste formulation recommended in the present study consisted of 100 parts of PVC (Zeon 121), 60 parts of dioctyl phthalate, 0.2 parts of MgO, and 6 parts of a 50% solution of DB-Na in butylcarbitol, which gave a highly crosslinked and transparent sheet with an excellent stability for thermal discolouring. The increasing viscosity behaviour of the paste during storage is explained by the effect of interparticle attracting forces of DB-Na which coordinates to the ether oxygen atoms in the glycol derivatives adsorbed on the surface of PVC particles. The increased viscosity can be reduced by addition of 3 parts of N-butyl-benzene-sulfonamide. The tension-distortion properties at elevated temperatures were remarkably improved at the crosslinked product compared with the uncrosslinked. The mechanical properties of the two crosslinked products produced via paste processing and roll-blending are compared in regard to the differences of the uniformity of crosslinking units.