Emission analysis of Azolla methyl ester with BaO nano additives for IC engine

The aim of this work is to decrease emissions in diesel engines fueled with diesel and algae biodiesel blends and also addition of BiO nanoparticles. Azolla algae can be used to produce biodiesel, because of high oil content. The biodiesel was prepared by using Azolla algae non-edible oil through transesterification process. In the present study, the BaO nano additives into the algae oil-based methyl ester blend and its diesel blends are analyzed the emission characteristic at different load. Addition of BaO nanoparticle was a strategy to reduce emission (CO, HC, and O₂) of the biodiesel.     

Emission analysis of Azolla methyl ester with Bi2O3 nano additives for IC engine

This work investigates the effect of using Bi₂O₃ nanoparticles at a different proportion of Azolla algae methyl ester in a four-stroke single cylinder diesel engine. Azolla algae can be used to produce biodiesel, because of high oil content. Biodiesel is developed by the transesterification of oil. In the present study, the Bi₂O₃ nano additives into the oil-based methyl ester blend and its diesel blends are analyzed the emission characteristic at different load. Addition of Bi₂O₃ nanoparticle is a strategy to reduce emission (CO, HC and smoke) of the biodiesel.     

Performance and emission analysis of cottonseed oil methyl ester in a diesel engine

In this study, performance and emissions of cottonseed oil methyl ester in a diesel engine was experimentally investigated. For the study, cottonseed oil methyl ester (CSOME) was added to diesel fuel, numbered D2, by volume of 5%(B5), 20%(B20), 50%(B50) and 75%(B75) as well as pure CSOME (B100). Fuels were tested in a single cylinder, direct injection, air cooled diesel engine. The effects of CSOME-diesel blends on engine performance and exhaust emissions were examined at various engine speeds and full loaded engine. The effect of B5, B20, B50, B75, B100 and D2 on the engine power, engine torque, bsfc's and exhaust gasses temperature were clarified by the performance tests. The influences of blends on CO, NO_x, SO₂ and smoke opacity were investigated by emission tests. The experimental results showed that the use of the lower blends (B5) slightly increases the engine torque at medium and higher speeds in compression ignition engines. However, there were no significant differences in performance values of B5, B20 and diesel fuel. Also with the increase of the biodiesel in blends, the exhaust emissions were reduced. The experimental results showed that the lower contents of CSOME in the blends can partially be substituted for the diesel fuel without any modifications in diesel engines.     

Performance and emission evaluation of a diesel engine fueled with methyl esters of rubber seed oil

Recent concerns over the environment, increasing fuel prices and scarcity of its supply have promoted the interest in development of the alternative sources for petroleum fuels. At present, biodiesel is commercially produced from the refined edible vegetable oils such as sunflower oil, palm oil and soybean oil, etc. by alkaline-catalyzed esterification process. This process is not suitable for production of biodiesel from many unrefined non-edible vegetable oils because of their high acid value. Hence, a two-step esterification method is developed to produce biodiesel from high FFA vegetable oils. The biodiesel production method consists of acid-catalyzed pretreatment followed by an alkaline-catalyzed transesterification. The important properties of methyl esters of rubber seed oil are compared with other esters and diesel. Pure rubber seed oil, diesel and biodiesel are used as fuels in the compression ignition engine and the performance and emission characteristics of the engine are analyzed. The lower blends of biodiesel increase the brake thermal efficiency and reduce the fuel consumption. The exhaust gas emissions are reduced with increase in biodiesel concentration. The experimental results proved that the use of biodiesel (produced from unrefined rubber seed oil) in compression ignition engines is a viable alternative to diesel.     

Combustion of algae oil methyl ester in an indirect injection diesel engine

An experimental study has been carried to use raw Algae oil and its methyl esters in an indirect injection diesel engine. Effects of engine speed, engine load output, injection timing of the algae biofuel and engine compression ratio on the engine output torque, combustion noise (maximum pressure rise rate), maximum pressure and maximum heat release rate have been studied. Raw oil extracted from microalgae and two versions of its methyl ester (0.1 and 0.2 methyl ester versions) have been evaluated in a Ricardo E6 engine. It has been shown that the algae oil methyl ester’s properties are similar to diesel fuel and its use has been successful in running the diesel engine smoothly. However, its use reduced the engine output torque slightly and increased the combustion noise. The engine output can be increased and the combustion noise can be reduced by controlling the engine design parameters e.g. injection timing and compression ratio.     

Emission characteristics of diesel engine operating on rapeseed methyl ester

Biofuels are being investigated as potential substitutes for current high pollutant fuels obtained from the conventional sources. In the past, fuels were generally selected on the basis of lowest cost relating to the requirements of the engine, and no attention was given to the possible effects of their use on the environment. Recent concerns over the environment, increasing liquid fuel prices and scarcity of supply in the last decade have promoted interest in the development of alternative sources of liquid energy. The purpose of this research was to evaluate the potential of rapeseed methyl ester (RME) as a liquid fuel for diesel engines in relation to meeting emission requirements. The test results showed that RME and its blends with diesel fuel emitted high CO₂ compared to test results on diesel fuel. A very significant reduction in emissions of hydrocarbon (HC) were recorded when running on RME and the blends. HC emissions were noted to increase with increased amount of diesel fuel in the blend. The fuel economy was a little worse when running on RME due to its low energy content. There were no marked difference noted for the exhaust temperatures of the blends, RME and diesel fuel at high speed operation. However, the diesel fuel operation produced high exhaust temperatures at low engine speed. Lubricating oil analysis showed reduction in viscosity indicating oil dilution.     

Performance and emissions of a diesel tractor engine fueled with marine diesel and soybean methyl ester

Biodiesel is an alternative fuel that is cleaner than petrodiesel. Biodiesel can be used directly as fuel for a diesel engine without having to modify the engine system. It has the major advantages of having high biodegradability, excellent lubricity and no sulfur content. This paper presents the results of investigations carried out in studying the fuel properties of soybean methyl ester (SME) and its blend with marine diesel fuel from 5%, 20% and 50% blends by volume and in running a diesel engine with these fuels. The results indicate that the use of biodiesel produces lower smoke opacity (up to 74%), but higher brake specific fuel consumption (BSFC) (up to 12%) compared to marine fuel (MF). The measured carbon monoxide (CO) emissions of B5 and B100 fuels were found to be 3% and 52% lower than that of the MF, respectively.     

Emission analysis of the effect of doped nano-additives on biofuel in a diesel engine

This study was aimed at hybrid nanocatalysts to reduce emissions of a diesel engine fueled with nanocatalyst biodiesel blends. Biodiesel was produced from Prosopis juliflora oil by the transesterification process. The nanocatalyst having cerium oxide on multiwall carbon a nanotube was investigated using biodiesel blends at two concentrations (50 and 100 ppm).The results revealed that the high surface area of the nanoparticles and their proper distribution along with catalytic oxidation reaction resulted in significant overall reductions in the emission. More specifically, all pollutants, i.e., CO, HC, and NOx, and smoke opacity were reduced when compared to B20.     

Direct injection diesel engine performance,emission, and combustion characteristics using diesel fuel,nonedible honne oil methyl ester,and blends with diesel fuel

Honne oil methyl ester (HOME) is produced from a nonedible vegetable oil, namely, honne oil, available abundantly in India. It has remained as an untapped new possible source of alternative fuel that can be used for diesel engines. The present research is aimed at investigating experimentally the performance, exhaust emission, and combustion characteristics of a direct injection diesel engine (single cylinder, water cooled) typically used in agricultural sector over the entire load range when fuelled with HOME and diesel fuel blends, HM20 (20% HOME + 80% diesel fuel)–HM100. The properties of these blends are found to be comparable with diesel fuel conforming to the American and European standards. The combustion parameters of HM20 are found to be slightly better than neat diesel (ND). For other blend ratios, these combustion parameters deviated compared with ND. The performance (brake thermal efficiency (BTE), brake‐specific fuel consumption, and exhaust gas temperature) of HM20 is better than ND. For other blend ratios, BTE is inferior compared with ND. The emissions (CO and SO) of HM20–HM100, throughout the entire load range, are dropped significantly compared with ND. Unburned hydrocarbon emissions of HM20–HM40, throughout the entire load range, is slightly decreased, whereas for other blend ratios, it is increased compared with ND. NO_x emissions of HM20, throughout the entire load range, is slightly increased, whereas for other blend ratios, it is slightly decreased. The reductions in exhaust emissions together with increase in BTE made the blend HM20 a suitable alternative fuel for diesel fuel and thus could help in controlling air pollution. Copyright © 2011 John Wiley & Sons, Ltd.     

Comparative assessment of a biogas run dual fuel diesel engine with rice bran oil methyl ester,pongamia oil methyl ester and palm oil methyl ester as pilot fuels

The present study tries to explore the potential of three different types of biodiesel viz. Rice bran oil methyl ester (RBME), Pongamia oil methyl ester (PME) and Palm oil methyl ester (POME) as pilot fuels for a biogas run dual fuel diesel engine designed for power generation. The results indicated that under dual fuel mode, RBME-biogas produced a maximum brake thermal efficiency of 19.97% in comparison to 18.4% and 17.4% respectively for PME-biogas and POME-biogas at 100% load. The emission study divulged that under dual fuel mode, on an average, there was an increase of CO emission by 25.74% and 32.58% for PME-biogas and POME-biogas, respectively in comparison to RBME-biogas. Furthermore, on an average, the HC emissions for PME-biogas and POME-biogas increased by 11.73% and 16.27%, respectively in comparison to RBME-biogas. On the other hand, on an average, there was a decrease in NO_X emission by 5.8% and 14%, respectively for PME-biogas and POME-biogas respectively in comparison to RBME-biogas.     

Performance evaluation of a diesel engine fueled with methyl ester of castor seed oil

In this investigation, castor methyl ester (CME) was prepared by transesterification using potassium hydroxide (KOH) as catalyst and was used in four stroke, single cylinder variable compression ratio type diesel engine. Tests were carried out at a rated speed of 1500 rpm at different loads. Straight vegetable oils pose operational and durability problems when subjected to long term usages in diesel engines. These problems are attributed to high viscosity, low volatility and polyunsaturated character of vegetable oils. The process of transesterification is found to be an effective method of reducing vegetable oil viscosity and eliminating operational and durability problems. The important properties of methyl ester of castor seed oil are compared with diesel fuel. The engine performance was analysed with different blends of biodiesel and was compared with mineral diesel. It was concluded that the lower blends of biodiesel increased the break thermal efficiency and reduced the fuel consumption. The exhaust gas temperature increased with increasing biodiesel concentration. The results proved that the use of biodiesel (produced from castor seed oil) in compression ignition engine is a viable alternative to diesel.     

Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters

The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NO_x. Overall fish biodiesel showed good combustion properties and environmental benefits.     

The emission analysis of an IDI diesel engine fueled with methyl ester of waste frying palm oil and its blends

In this study, the exhaust emissions of an unmodified diesel engine fueled with methyl ester of waste frying palm-oil (biodiesel) and its blends with petroleum based diesel fuel (PBDF) were investigated at the full load-variable speed condition. The relationships between the fuel properties and the air–fuel equivalence ratio, fuel line pressure, start of injection (SOI) timing, and ignition delay were also discussed to explain their effects on the emissions. The obtained test results were compared with the reference values which were determined by using PBDF. The results showed that when biodiesel was used in the test engine, the fuel line pressure increased while air–fuel equivalence ratio and ignition delay decreased. These behaviors affected the combustion phenomena of biodiesel which caused to reduction 57% in carbon monoxide (CO) emission, about 40% in unburned hydrocarbon (HC) emission and about 23% in smoke opacity when compared with PBDF. However, NO_x and CO₂ emissions of the biodiesel have showed different behaviors in terms of the engine speed.     

Performance and exhaust emission characteristics of a CI engine fueled with Pongamia pinnata methyl ester (PPME) and its blends with diesel

Transport vehicles greatly pollute the environment through emissions such as CO, CO₂, NO_x, SO_x, unburnt or partially burnt HC and particulate emissions. Fossil fuels are the chief contributors to urban air pollution and major source of green house gases (GHGs) and considered to be the prime cause behind the global climate change. Biofuels are renewable, can supplement fossil fuels, reduce GHGs and mitigate their adverse effects on the climate resulting from global warming. This paper presents the results of performance and emission analyses carried out in an unmodified diesel engine fueled with Pongamia pinnata methyl ester (PPME) and its blends with diesel. Engine tests have been conducted to get the comparative measures of brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC) and emissions such as CO, CO₂, HC, NO_x to evaluate the behaviour of PPME and diesel in varying proportions. The results reveal that blends of PPME with diesel up to 40% by volume (B40) provide better engine performance (BSFC and BSEC) and improved emission characteristics.     

Effect of metal based additive on performance emission and combustion characteristics of diesel engine fuelled with biodiesel

This study investigates the use of ferric chloride (FeCl₃) as a fuel borne catalyst (FBC) for waste cooking palm oil based biodiesel. The metal based additive was added to biodiesel at a dosage of 20 μmol/L. Experiments were conducted to study the effect of ferric chloride added to biodiesel on performance, emission and combustion characteristics of a direct injection diesel engine operated at a constant speed of 1500 rpm at different operating conditions. The results revealed that the FBC added biodiesel resulted in a decreased brake specific fuel consumption (BSFC) of 8.6% while the brake thermal efficiency increased by 6.3%. FBC added biodiesel showed lower nitric oxide (NO) emission and slightly higher carbon dioxide (CO₂) emission as compared to diesel. Carbon monoxide (CO), total hydrocarbon (THC) and smoke emission of FBC added biodiesel decreased by 52.6%, 26.6% and 6.9% respectively compared to biodiesel without FBC at an optimum operating condition of 280 bar injection pressure and 25.5^o bTDC injection timing. Higher cylinder gas pressure, heat release rate and shorter ignition delay period were observed with FBC added biodiesel at these conditions.     

The use of Koroch seed oil methyl ester blends as fuel in a diesel engine

An experimental investigation was carried out on a small direct injection (DI) diesel engine, fuelling the engine with 10% (B10), 20% (B20), 30% (B30) and 40% (B40) blending of Koroch seed oil methyl ester (KSOME) with diesel. The performance and combustion characteristics of the engine at various loads are compared and analyzed. The results showed higher brake specific fuel consumption (BSFC) and lower brake thermal efficiency (BTE) for the KSOME blends. The engine indicated power (IP) was more for the blends up to B30, but found to be reduced for the blend B40 when compared to that of diesel. The engine combustion parameters such as pressure crank angle diagram, peak pressure, time of occurrence of peak pressure, net heat-release rate, cumulative heat release, ignition delay and combustion duration were computed. The KSOME blends exhibited similar combustion trend with diesel. However, the blends showed an early start of combustion with shorter ignition delay period. The study reveals the suitability of KSOME blends up to B30 as fuel for a diesel engine mainly used in generating sets and the agricultural applications in India without any significant drop in engine performance.     

Performance and emission study of preheated Jatropha oil on medium capacity diesel engine

Diesel engines have proved its utility in transport, agriculture and power sector. Environmental norms and scared fossil fuel have attracted the attention to switch the energy demand to alternative energy source. Oil derived from Jatropha curcas plant has been considered as a sustainable substitute to diesel fuel. However, use of straight vegetable oil has encountered problem due to its high viscosity. The aim of present work is to reduce the viscosity of oil by heating from exhaust gases before fed to the engine, the study of effects of FIT (fuel inlet temperature) on engine performance and emissions using a dual fuel engine test rig with an appropriately designed shell and tube heat exchanger (with exhaust bypass arrangement). Heat exchanger was operated in such a way that it could give desired FIT. Results show that BTE (brake thermal efficiency) of engine was lower and BSEC (brake specific energy consumption) was higher when the engine was fueled with Jatropha oil as compared to diesel fuel. Increase in fuel inlet temperature resulted in increase of BTE and reduction in BSEC. Emissions of NO_x from Jatropha oil during the experimental range were lower than diesel fuel and it increases with increase in FIT. CO (carbon monoxide), HC (hydrocarbon), CO₂ (carbon dioxide) emissions from Jatropha oil were found higher than diesel fuel. However, with increase in FIT, a downward trend was observed. Thus, by using heat exchanger preheated Jatropha oil can be a good substitute fuel for diesel engine in the near future. Optimal fuel inlet temperature was found to be 80 °C considering the BTE, BSEC and gaseous emissions.     

Performance and emission study on the effect of oxygenated additive in neat biodiesel fueled diesel engine

This work presents the effect of the Di-tetra-butyl-peroxide (DTBP) as an oxygenated additive on neat used mustard oil biodiesel (B100) to evaluate the emission and performance engine characteristics. Four fuels, namely, diesel, biodiesel (Mustard biodiesel), a blend of B100-10percentage, and 20% by volume of DTBP (BD90DTBP10 and BD80DTBP20) are prepared and tested on a single cylinder, constant speed diesel engine. Experimental outcomes revealed that 20% of DTBP reduces 7.3% CO, 5.1% HC, and 4.6% NOx and 3.2% smoke emissions of B100. From this study, further, it is inferred that BD80DTBP20 blend could be utilized as an alternative fuel for a CI engine with no modifications in engine design.     

Environment effect of La2O3 nano-additives on microalgae-biodiesel fueled CRDI engine with conventional diesel

In this present work, corn oil biodiesel with La₂O₃ was used as an additive with neat diesel fuel and blends were prepared. La₂O₃ nanoparticles are dispersed in the emulsions with different dosage levels of 50, 75, and 100 ppm. A single-cylinder, four-stroke CRDI diesel engine is made to run on different fuel concentrations to study the effect of emission characteristics of the fuel. The test engine was operated under constant engine speed (1500 rpm) and different engine load test conditions. According to the experimental results, fuel blends with biodiesel fuel emission increases CO₂ and NOx and reduces the CO, HC, and smoke emissions compared with the B20 fuel.     

Performance,emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends

The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with waste cooking oil methyl ester and its 20%, 40%, 60% and 80% blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of waste cooking oil methyl ester as a biofuel has been established in this study. Bio diesel produced from waste sun flower oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 18:1, 19:1, 20:1, 21:1 and 22:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for waste cooking oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.