Preparation and electroresponsive property of poly(vinyl alcohol)/sodium alginate composite hydrogel

Poly(vinyl alcohol) (PVA)/sodium alginate composite hydrogel was prepared by solidifing the blending solution of PVA and sodium alginate, then freezing and thawing repeatedly. In the direct current electric field, the composite hydrogel in aqueous NaCl solution swelled, contracted, and bent. The gel's bending speed and maximum bending degree increased with increase in the electric field intensity and the concentration of NaCl solution. The maximum bending degree increased with increase in the sodium alginate content in the composition hydrogel. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3493–3496, 2006     

Preparation and properties of keratin–poly(vinyl alcohol) blend fiber

Keratin–poly(vinyl alcohol) (PVA) blend fibers containing 13–46 wt % of –SSONa⁺ (S‐sulfo) keratin were prepared by the wet‐spinning technique. They were formed by dehydration of an aqueous solution of S‐sulfo keratin and PVA (spinning dope) in a coagulation bath of sodium sulfate–saturated solution and subsequently drawn. Keratin–PVA fibers showed higher tenacity than that of wool, presumably originating from the high mechanical strength of the PVA component. The heat treatment at about 200°C improved the waterproof characteristics such as shrinkage of keratin–PVA fibers more conspicuously than did PVA fibers. That is, after heat treatment at 195°C for 10 min, keratin–PVA blend fiber shrank 20% in water at 60°C, whereas PVA fiber shrank 56%. Differential thermal analysis suggested the crosslinking of disulfide bonds between keratin molecules during the heat treatment, whereas the additional crystallization of PVA component was not observed. Adsorption of heavy metal and toxic gas to keratin–PVA fibers was also investigated. Keratin–PVA fiber was found to adsorb Ag⁺ and formaldehyde gas more efficiently than PVA. Thus, blends of keratin and PVA were advantageous for both polymer fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 756–762, 2004     

A poly(vinyl alcohol)/sodium alginate blend monolith with nanoscale porous structure

A stimuli-responsive poly(vinyl alcohol) (PVA)/sodium alginate (SA) blend monolith with nanoscale porous (mesoporous) structure is successfully fabricated by thermally impacted non-solvent induced phase separation (TINIPS) method. The PVA/SA blend monolith with different SA contents is conveniently fabricated in an aqueous methanol without any templates. The solvent suitable for the fabrication of the present blend monolith by TINIPS is different with that of the PVA monolith. The nanostructural control of the blend monolith is readily achieved by optimizing the fabrication conditions. Brunauer Emmett Teller measurement shows that the obtained blend monolith has a large surface area. Pore size distribution plot for the blend monolith obtained by the non-local density functional theory method reveals the existence of the nanoscale porous structure. Fourier transform infrared analysis reveals the strong interactions between PVA and SA. The pH-responsive property of the blend monolith is investigated on the basis of swelling ratio in different pH solutions. The present blend monolith of biocompatible and biodegradable PVA and SA with nanoscale porous structure has large potential for applications in biomedical and environmental fields.     

Study of electrospinning of sodium alginate,blended solutions of sodium alginate/poly(vinyl alcohol) and sodium alginate/poly(ethylene oxide)

Alginate is an interesting natural biopolymer for many of its merits and good biological properties. This paper investigates the electrospinning of sodium alginate (NaAlg), NaAlg/PVA‐ and NaAlg/PEO‐ blended systems. It was found in this research that although NaAlg can easily be dissolved in water, the aqueous NaAlg solution could not be electrospun into ultrafine nanofibers. To overcome the poor electrospinnability of NaAlg solution, synthetic polymers such as PEO and PVA solutions were blended with NaAlg solution to improve its spinnability. The SEM images of electrospun nanofibers showed that the alginate (2%, w/v)–PVA (8%, w/v) blended system in the volume ratio of 70 : 30 and the alginate (2%, w/v)–PEO (8% w/v) blended system in the volume ratio of 50 : 50 could be electrospun into finest and uniform nanofibers with average diameters of 118.3 nm (diameter distribution, 75.8–204 nm) and 99.1 nm (diameter distribution, 71–122 nm), respectively. Rheological studies showed a strong dependence of spinnability and fiber morphology on solution viscosity and thus on the alginate‐to‐synthetic polymer (PVA or PEO) blend ratios. FTIR studies indicate that there are the hydrogen bonding interactions due to the ether oxygen of PEO (or the hydroxyl groups of PVA) and the hydroxyl groups of NaAlg. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Photodependent release from poly(vinyl alcohol)/epoxypropoxy coumarin hydrogels

To obtain a photoresponsive hydrogel, poly(vinyl alcohol) (PVA) having coumarin residue as a pending group was crosslinked by photodimerizing the coumarin pendants. PVA having coumarin pendants was prepared by reacting the polymer with epoxypropoxy coumarin (EPC) in a strong alkali condition with EPC/PVA molar ratio of 200/1. According to the 1H NMR spectrum of PVA‐EPC conjugate, the molar ratio of EPC residue to PVA was about 4.3/1, indicating that EPC was attached to PVA every 444 repeating units of vinyl alcohol. An aqueous solution of PVA‐EPC (5%, w/v) became a semi‐solid hydrogel by the irradiation of a light (λ = 365 nm; 400 W) for 1 hr. The dimerization degree of EPC residues of the hydrogel decreased and increased in a periodical manner under the cyclic irradiation between two UV lights (λ = 365 nm and λ = 254 nm). The release of 5(6)‐carboxyfluorescein (CF) from PVA‐EPC hydrogel was significantly enhanced by the 5 min‐irradiation of λ = 254 nm (6 W), possibly due to the photodedimerization of EPC residues of the hydrogel. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal and spectroscopic studies of poly(N‐vinyl pyrrolidone)/poly(vinyl alcohol) blend films

Poly(N‐vinyl pyrrolidone) (PVP) and poly (vinyl alcohol) (PVA) homopolymers and their blended samples with different compositions were prepared using cast technique and subjected to X‐ray diffraction (XRD) measurements, infrared (IR) spectroscopy, ultraviolet/visible spectroscopy, and thermogravimetric analysis (TGA). XRD patterns of homopolymers and their blended samples indicated that blending amorphous materials, such as PVP, with semicrystalline polymer, such as PVA, gives rise to an amorphous structure with two halo peaks at positions identical to those found in pure PVP. Identification of structure and assignments of the most evident IR ‐ absorption bands of PVP and PVA as well as their blends in the range 400–2000 cm^?1 were studied. UV–vis spectra were used to study absorption spectra and estimate the values of absorption edge, E_g, and band tail, E_e, for all samples. Making use of Coats‐Redfern relation, thermogravimetric (TG) data allowed the calculation of the values of some thermodynamic parameters, such as activation energy E, entropy ΔS^#, enthalpy ΔH, and free energy of activation ΔG^# for different decomposition steps in the samples under investigation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of interpenetrating network beads of poly(vinyl alcohol)‐grafted‐poly(acrylamide) with sodium alginate and their controlled release characteristics for cypermethrin pesticide

Interpenetrating network polymeric beads of poly(vinyl alcohol)‐grafted‐acrylamide with sodium alginate have been prepared by crosslinking with glutaraldehyde. Cypermethrin, a widely used pesticide, was loaded with 80% efficiency in these hydrogel beads. The beads were characterized by Fourier transform infrared spectroscopy to confirm the grafting. Scanning electron microscopy was used to know the morphology of the beads. Equilibrium swelling experiments indicated that swelling of the beads decreased with an increase in crosslinking. The in vitro release studies were performed under static conditions and the release data have been fitted to an empirical relation to estimate the transport parameters. The diffusion coefficients have been calculated for the transport of pesticide through the polymeric beads using the initial time approximation method. These values showed decrease with increasing crosslinking as well as increasing pesticide loading. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 552–560, 2002; DOI 10.1002/app.10306     

Synthesis of copolymeric acrylamide/potassium acrylate hydrogels blended with poly(vinyl alcohol): Effect of crosslinking and the amount of poly(vinyl alcohol) on swelling behavior

A novel series of copolymeric acrylamide/potassium acrylate superabsorbents, blended with poly(vinyl alcohol), have been synthesized by using N, N′‐methylenebisacrylamide as a crosslinker and potassium persulphate (K₂S₂O₈) as an initiator. Swelling behavior of these hydrogels in water was investigated; and on the basis of swelling properties, the diffusional behavior of water into these hydrogel systems was analyzed. It was observed that with the increase of amount of poly(vinyl alcohol) or crosslinking, the swelling of the hydrogels decreased. The hydrogel synthesized by addition of 5% poly(vinyl alcohol) and 0.25% crosslinking showed maximum swelling of 54445%. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1927–1931, 2005     

Swelling and mechanical behavior of modified poly(vinyl alcohol)/laponite nanocomposite membranes

Nanocomposite (NC) membranes based on hydrophobically modified PVA and laponite were synthesized with varying laponite content in the feed. The incorporation of laponite in NC membranes was investigated by FTIR spectroscopy and thermogravimetric analysis. The swelling ratio of membranes was determined as a function of temperature and laponite content. Swelling studies of NC membranes exhibited the decrease in swelling with an increase in laponite content in the NC membranes. The swelling ratio of NC membrane with 20% laponite slightly increased with an increase in temperature. Dynamic mechanical analysis showed the systematic increase in storage modulus with laponite content, which indicates the enhancement of mechanical property upon laponite addition. There was also a decrease in the tan δ peak values of NC membranes with an increase in laponite content in NCs. The permeabilities through NC membranes as a function of solute size and laponite content were studied and the results showed molecular screening based on size. The permeability of solute reduced due to the presence of well‐dispersed laponite in the NC. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2896–2903, 2007     

Thermal and mechanical behaviors of poly(vinyl alcohol)–lactose blends

Thermal and mechanical behaviors of poly(vinyl alcohol) (PVA)–lactose blends were studied by differential scanning calorimetry, thermal gravimetric analysis, and stress–strain analysis. The increase in glass transition temperature of the PVA–lactose blends with lactose contents suggests the formation of hydrogen‐bonded PVA–lactose complex in the PVA matrix. The hydrogen bonding interactions can improve thermal and mechanical properties of the blends. Results of this study demonstrate that lactose, a byproduct of dairy industry, can be used directly and in substantial quantity (33%) as a modifier to enforce the physical properties of PVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 929–935, 2002     

辐照法制备聚乙烯醇水凝胶研究进展

简要评述了聚乙烯醇水凝胶的制备方法,分析了各种方法的优点和缺点,介绍聚乙烯醇辐照交联的基本原理,并展望了辐射交联聚乙烯醇水凝胶研究及应用前景.     

Network characterization and swelling behavior of chemical hydrogels based on acid‐containing poly(vinyl alcohol)

Poly(vinyl alcohol) (PVA) was modified with phthalic and succinic anhydrides to give vinyl alcohol–vinyl ester copolymers that contain carboxylate groups. These half‐esters were then crosslinked by using the poly‐ (ethylene glycol) (PEG) 400 diglycidylether. Low crosslinker/carboxylate ratios were used to obtain low degrees of crosslinking, so the capacity of the resulting hydrogel to absorb water was high. Water absorption was determined gravimetrically as a function of time at room temperature. The equilibrium swelling ratio and compressive modulus were characterized for all the resulting PVA hydrogels and related to the network structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3026–3031, 2003     

Preparation and characterization of poly(vinyl alcohol)‐poly(vinyl pyrrolidone) blend: A biomaterial with latent medical applications

Aqueous solutions of poly(vinyl alcohol) and poly(vinyl pyrrolidone) are blended and films are produced by casting method with the further intention of being used as bio‐materials with latent medical application. Glutaraldehyde, 4,4′‐diazido‐2,2′‐stilbenedisulfonic acid disodium salt tetra‐hydrate are used as crosslinker agents, whereas lactic acid is the plasticizer in the blend. The obtained films are characterized by differential scanning calorimetry (DSC), mechanical properties, swelling and solubility behavior. DSC measurements show that the blends exhibit a single glass transition temperature indicating that they are miscible, even in the presence of the plasticizer and crosslinker agents. By the combination of all mentioned additives, a relevant enhancement of the swelling is observed, accompanied by a stabilization of the solubility during the tested time. Finally, mechanical properties show an appropriate performance in the studied parameters. As a consequence, the obtained films could be suitable for use as medium or long‐term implants. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Swollen behavior of crosslinked network hydrogels based on poly(vinyl alcohol) and polydimethylsiloxane

Poly(vinyl alcohol) (PVA) was dissolved in the water to make a 10 wt % aqueous solution, and polydimethylsiloxane (PDMS) was mixed with 1 wt % 2,2‐dimethyl‐2‐phenylacetophenone (DMPAP) and 0.5 mol % methylenebisacrylamide (MBAAm) in isopropyl alcohol. This mixture was added to a PVA aqueous solution and heated at 90°C for 7 h. Various crosslinked networks were prepared at different molar ratios of PVA/PDMS (1:1, 1:3, and 3:1). The characterization of PVA/PDMS crosslinked networks was determined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), a universal testing machine (UTM), and the equilibrium water content (EWC). The DSC melting endotherms showed, at 219.49°C, a sharp endothermic peak of PVA, and PVA/PDMS crosslinked networks had melting peaks close to this point. The value of EWC increased with the content of PVA in the crosslinked networks, simultaneously depending on the temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 957–964, 2002     

Characterization of degraded hydrogels based on poly(vinyl alcohol) grafted with poly(lactide‐co‐glycolide)

Poly(vinyl alcohol) (PVA) grafted with poly(lactide‐co‐glycolide) and cross‐linked as a material of increased hydrophobicity relative to PVA was produced. The properties were examined with respect to the mass loss, water uptake, hydrophilicity, and mechanical characteristics upon hydrolytical degradation. The hydrogels investigated display water uptake increasing with degradation time because of increasing hydrophilicity. The mass loss amounts up to 15% after eight weeks of degradation. The mechanical properties of the hydrogels are within the range of those of natural tissue, the E modulus is 18 MPa, or even 100–200 MPa, depending on the structure of material. The mechanical characteristic and their dependence degradation show the most recognizable correlation with the chemical structure. Studies of the topography of degraded samples (scanning electron microscopy) and IR measurements demonstrate the degradation to occur at slow rate due to the high degree of grafting. The mass loss is rather low and a bulk degradation mechanism takes place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Properties and structure of poly(vinyl alcohol)/silica composites

The relationships between the properties and structure are discussed for poly(vinyl alcohol)(PVA)/silica composites prepared through the sol‐gel process. The composites became stiff and brittle with increasing the silica content. The properties of the composites were changed drastically at around the composition of PVA/silica = 70/30 wt %. For example, there was no large change in the Young's modulus above 30 wt % of silica content (Pure PVA: 31.8 MPa, silica 30%: 52.6 MPa, silica 50%: 55.2 MPa). Consequently, it was considered that the three‐dimensional network structure of silica could be formed in the composite with more than 30 wt % of silica in PVA. From this behavior, it could be considered that the crystal growth of PVA was remarkably inhibited by silica network. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 133–138, 1999     

Drug release behavior of electrical responsive poly(vinyl alcohol)/poly(acrylic acid) IPN hydrogels under an electric stimulus

The electrically modulated properties of interpenetrating polymer networks (IPN) composed of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAAc) under electric field were investigated for drug delivery systems. PVA/PAAc IPNs with various compositions were synthesized by a sequential method, that is, ultraviolet polymerization of AAc in the mixture of PVA and aqueous AAc monomer solution, followed by a freeze‐thawing process to prepare elastic hydrogels. The amount of loaded drug significantly increased with the content of PAAc containing ionizable groups in IPN. The amount of introduced ionic drug (cefazoline) was greater than that of the nonionic drug (theophylline). Release behaviors of drug molecules from negatively charged PVA/PAAc IPN were switched on and off in a pulsatile pattern depending on the applied electric stimulus. The released amount and the release rate of drug were influenced significantly by the applied voltage, ionic group contents in IPN, ionic properties of drug solute, and the ionic strength of release medium. In addition, the ionic properties of drug molecules dramatically affected release behaviors, thus the release of ionic drug was much more enhanced than that of the nonionic drug. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1752–1761, 1999     

Interfacial interaction and mechanical properties of chitin whisker–poly(vinyl alcohol) gel‐spun nanocomposite fibers

Nanocomposite fibers were prepared from chitin whiskers (ChWs) as the reinforcing phase and poly(vinyl alcohol) (PVA) as the matrix. Colloidal suspensions of ChWs, obtained by acid hydrolysis of chitin from crab shell, were thoroughly mixed with aqueous PVA. The homogeneous PVA–ChW suspensions were gel‐spun into a methanol coagulating bath. Wide‐angle X‐ray diffraction patterns evidenced the orientation of ChWs along the fiber axis. From differential scanning calorimetry, the crystallinity of the PVA component was found to increase with ChW loading due to the possible dragging of PVA chains adhering to ChWs during vertical extrusion. The non‐isothermal crystallization peak of PVA was observed to shift to lower temperature with ChW loading indicating interfacial interactions between PVA and ChW. Further interaction between PVA and ChW was evidenced by the shifting of the Fourier transform infrared bands of PVA to lower wavenumber and the dynamic tan δ peak, corresponding to α‐relaxation of PVA, shifting to higher temperature. The interaction of ChWs with the matrix PVA yielded a significant enhancement in the mechanical properties of the nanocomposites. Copyright © 2012 Society of Chemical Industry     

Effect of stereoregularity and molecular weight on the mechanical properties of poly(vinyl alcohol) hydrogel

The effect of the stereoregularity and molecular weight of poly(vinyl alcohol) (PVA) on the mechanical properties of hydrogel was investigated. Compressive strength, creep behavior, and dynamic viscoelasticity were measured on hydrogels of syndiotacticity‐rich PVA derived from poly(vinyl pivalate) (D_p = 1690 diad‐syndiotacticity = 61%, D_p = 8020 diad‐syndiotacticity = 62%) and atactic PVA (D_p = 1750 diad‐syndiotacticity = 54%, D_p = 7780 diad‐syndiotacticity = 54%). Increasing the molecular weight of molecular chains constituting the gel improved the compressive strength of atactic PVA hydrogel. The stereoregularity of PVA had a greater effect than molecular weight on the strength of the hydrogel. Gel prepared from 8.8 g/dL syndiotacticity‐rich PVA had a high compressive modulus of 10 kPa, and the compressive modulus of the gel prepared from 3.3 g/dL was comparable with that of atactic PVA hydrogel prepared with more than 6 g/dL. The dynamic storage modulus of the gel derived from syndiotacticity‐rich PVA was remarkably higher than that of the atactic PVA gel and remained constant up to 60°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of chitosan/poly(vinyl alcohol) blend fibers

Chitosan and poly(vinyl alcohol) blend fibers were prepared by spinning their solution through a viscose‐type spinneret at 25°C into a coagulating bath containing aqueous NaOH and ethanol. The influence of coagulation solution composition on the spinning performance was discussed, and the intermolecular interactions of blend fibers were studied by infrared analysis (IR), X‐ray diffraction (XRD), and scanning electron micrograph (SEM) and by measurements of mechanical properties and water‐retention properties. The results demonstrated that the water‐retention properties and mechanical properties of the blend fibers increase due to the presence of PVA in the chitosan substract, and the mechanical strength of the blends is also related to PVA content and the degree of deacetylation of chitosan. The best mechanical strength values of the blend fibers, 1.82 cN/d (dry state) and 0.81 cN/d (wet state), were obtained when PVA content was 20 wt % and the degree of deacetylation of chitosan was 90.2%. The strength of the blend fibers, especially wet tenacity could be improved further by crosslinking with glutaraldehyde. The water‐retention values (WRV) of the blend fibers were between 170 and 241%, obviously higher than pure chitosan fiber (120%). The structure analysis indicated that there are strong interaction and good miscibility between chitosan and poly(vinyl alcohol) molecular resulted from intermolecular hydrogen bonds. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2558–2565, 2001