Comparative study on electrical properties of copper nanowire/polypropylene and carbon nanotube/polypropylene composites

Nanocomposites using copper nanowires (CuNWs) or carbon nanotubes (CNTs) as fillers with polypropylene (PP) as matrix were prepared by miscible solution mixing and precipitation method. Comparative studies on electrical conductivity and electromagnetic interference shielding properties were reported. On the conductivity curve, a plateau was found for both CuNW/PP composite and CNT/PP composite. The plateaus are located at a different concentration range for each composite type: for CuNW/PP composite, it is between 0.8 and 1.7 vol %, while for CNT/PP composite the plateau occurs in a narrower range between 0.4 and 0.6 vol %. The shielding effectiveness (SE) increases with increased concentration of fillers. CNT/PP composite has higher SE at concentrations less than 2 vol %; the two curves cross near 10 dB at this point and at concentrations higher than 2 vol %, CuNW/PP composite has higher SE. © 2014 American Institute of Chemical Engineers AIChE J, 61: 296–303, 2015     

Structural characterization and electrical properties of carbon nanotubes/epoxy polymer composites

The purpose of this study is to identify the relationship between the electrical and structural characteristics of multiwalled carbon nanotubes dispersed into the polymer matrix of a resin. In a first step, the composites were characterized by small‐angle neutron scattering, which provide information about the bulk dispersion of nanotubes in the matrix and form three‐dimensional networks with a surface fractal behavior. In the second step, a dielectric and electrical study was carried out in the frequency range between 1 Hz and 10 MHz at room temperature. We have found that the electric and dielectric behavior of these composites can be described by Jonscher's universal dielectric response. We show that the critical exponents describing the concentration dependence of the conductivity and the dielectric constant, obtained in the vicinity of the percolation threshold, are in good agreement with the theoretical values. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44514.     

多壁碳纳米管／环氧树脂复合材料性能研究

采用物理机械方法与化学方法相结合的手段,制备了多壁碳纳米管（MWNTS）／环氧树脂（Epoxy）复合材料。通过力学拉伸试验测试了MWNTs/Epoxy复合材料拉伸强度和拉伸模量与MWNTS添加量的关系,利用扫描电镜（SEM）分析了MWNTS／Epoxy复合材料的拉伸断面,并用表面电阻测试仪对所制备的碳纳米管复合材料进行了电学性能测试。结果表明：经过化学酸化的方法处理后的MWNTS在复合材料中的分散得到了改善,力学性能也得到了明显的提高,但酸处理后的复合材料的电学性能明显低于未处理的复合材料。     

紫外光辐照反-1,4-聚异戊二烯/碳纳米管复合材料

在室温和氮气环境下 ,用反 - 1,4 -聚异戊二烯 (TPI)与碳纳米管 (CNT)经紫外光辐照制备了TPI/CNT复合材料。实验表明 ,TPI与CNT的复合材料或二者直接共混物的电阻率 (ρv)均随CNT质量分数的增加而下降 ;前者的导电性优于后者。CNT质量分数为 5 %时 ,TPI/CNT复合材料的 ρv 与TPI相比 ,下降了 7个数量级 ,为 6 .0 7× 10 8Ω·cm。在紫外光辐照下 ,CNT可在TPI基质中均匀分布 ,形成导电网络     

炭黑/环氧树脂复合材料的制备及电性能研究

介绍了以二氧化硅为分散剂的炭黑/二氧化硅/环氧树脂基复合材料的组成、制备、导电机理,渗流阈值及PTC效应。分析了影响其PTC效应的因素,包括炭黑粒子、聚合物基体以及材料的加工工艺等。     

A modified model of electrical conduction for carbon black–polymer composites

A modified model of electrical conduction for carbon black‐polymer composites is proposed based on the general effective media theory and the number of carbon black particles per aggregate to describe their nonlinear conductive behavior. In order to consider the interactions between carbon black particles, a simple self‐consistent approach is used to improve the model. Expressions of electrical conductivity and percolation threshold are derived from the modified model. The predicted results of electrical conductivity and percolation threshold are in good agreement with experimental data reported in previous literature. Moreover, the dependences of electrical conductivity and percolation threshold on the number of carbon black particles per aggregate are discussed. Copyright © 2010 Society of Chemical Industry     

Evaluation of the rheological and electrical percolation of high-density polyethylene/carbon black composites using mathematical models

In this work, conductive polymer composites (CPCs) of bio-based polyethylene (BioPe) containing different concentrations of carbon black (CB) were developed. By using oscillatory rheology analysis, a Newtonian plateau was observed in BioPe, and all BioPe/CB composites had a behavior of a pseudo-solid and that composites with volume fractions ranging from 0.24 to 0.56 presented higher viscosity, storage, and loss modulus. This suggests the formation of a percolated network and by using the power-law models, it was observed that the electrical percolation threshold was higher than the rheological percolation threshold. The electrical conductivity was measured using the four-point probe method and a sigmoid model was used to predict the CPCs' electrical conductivity percolation threshold. The results indicated that the four-point probe method presented satisfactory results according to the calculated standard deviations and voltage–current characteristics for each round of measurements considering the same ranging as used in rheology analysis. The analytical model used showed a coefficient of determination (R²) higher than 95%, allowing the prediction of the electrical conductivity of the CPC and the percolation threshold as a function of the volumetric fraction of the CB.     

Linear viscoelastic properties and crystallization behavior of multi‐walled carbon nanotube/polypropylene composites

Multi‐walled carbon nanotube/polypropylene composites (PPCNs) were prepared by melt compounding. The linear viscoelastic properties, nonisothermal crystallization behavior, and kinetics of PPCNs were, respectively, investigated by the parallel plate rheometer, differential scanning calorimeter (DSC), X‐ray diffractometer (XRD), and polarized optical microscope (POM). PPCNs show the typical nonterminal viscoelastic response because of the percolation of nanotubes. The rheological percolation threshold of about 2 wt % is determined using Cole‐Cole method. Small addition of nanotube can highly promote crystallization of PP matrix because of the heterogeneous nucleating effect. With increasing nanotube loadings, however, the crystallization rate decreases gradually because the mobility of PP chain is restrained by the presence of nanotube, especially at high loading levels. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Electrical,rheological, and mechanical properties copolymer/carbon black composites

This work aims to evaluate the electrical conductivity and the rheological and mechanical properties of copolymer/carbon black (CB) conductive polymer composites (CPCs). The copolymers, containing ethylene groups in their structure, used as matrix were polyethylene grafted with maleic anhydride (PEgMA), ethylene-methyl acrylate–glycidyl methacrylate (EMA-GMA), and ethylene-vinyl acetate (EVA). For comparison purposes, bio-based polyethylene (BioPE)/CB composites were also studied. The electrical conductivity results showed that the electrical percolation threshold of BioPE/CB composite was 0.36 volume fraction of CB, whereas the rheological percolation threshold was 0.25 volume fraction of CB. The most conductive CPC was BioPE/CB. Among the copolymer/CB CPCs, PEgMA/CB showed the highest conductivity, which can be attributed to the fact that the PEgMA copolymer had higher crystallinity. It also has a higher amount of ethylene groups in its structure. Torque rheometry analysis indicated that EMA-GMA copolymer may have reacted with CB. Rheological measurements under oscillatory shear flow indicated the formation of a percolated network in BioPE/CB and copolymer/CB composites. Morphology analysis by scanning electron microscopy (SEM) indicated the formation of a percolated network structure in BioPE/CB composite and finely dispersed CB particles within the PEgMA copolymer. Wetting of CB particles/agglomerates by the copolymer matrix was observed in EVA/CB and EMA-GMA/CB composites. Conductive CB acted as reinforcing filler as it increased the elastic modulus and tensile strength of BioPE and the copolymers.     

Conductive sizing for improving electrical conductivity of carbon fiber/polyaryl ether ketone/AgNWs composites

The aim of this work is to enhance the electrical conductivity of PAEK/continuous carbon fiber (CF) composites while maintaining their mechanical properties. A conductive sizing was elaborated by mixing polyetherimide (PEI) with silver nanoplates (AgNpts) in suspension in dichloromethane. An aqueous PEI formulation was used as insulating sizing reference. The presence of AgNpts into the sizing enhances electrical conductivity up to 0.2 S.m⁻¹ for a silver content ∼ 0.2 vol % without any modification of mechanical properties. The influence of conductive sizing on PAEK–AgNWs/CF was observed. For low AgNWs content lower (<1 vol %); the conductive sizing increases the electrical conductivity of the composite by one decade. This result shows that both types of Ag particles participate to the conductive path. For higher AgNWs content, electrical conductivity (200 S.m⁻¹) is independent from the AgNpts content: the conductive path is only constituted by AgNWs. Mechanical properties of such composites show that the value of the conservative modulus is almost the same, while the dissipative modulus slightly increases. The global mechanical properties of the composite are preserved despite the addition of the CF, AgNWs, and AgNpts. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47872.     

Dielectric properties of epoxy composites with modified multiwalled carbon nanotubes

We report here a high dielectric percolative polymer nanocomposite, fabricated by a combination of triethylene-tetramine (TETA) modified multiwalled carbon nanotube (named as TETA-MWNT) within epoxy resin matrix. In this composite system, with various TETA-MWNT volume fractions, the dielectric constant (K) is well fitted by the scaling law of the percolation theory with the percolation threshold f _c is 0.042 and the critical exponent p is 0.786. At 1,000 Hz of room temperature, the value of the dielectric constant is as high as 421 with the TETA-MWNT content of 4.14vol%, which is almost 60 times higher than that of epoxy resin. In contrast, a simple blend of pristine MWNT in epoxy composite shows evident lower dielectric constant and much higher loss with the same volume fraction.     

碳纳米管增强环氧／石墨复合材料的制备与性能研究

采用粉末冶金法制备了碳纳米管增强环氧／石墨复合材料,并研究了酸洗处理对复合材料弯曲强度、硬度和导电性能的影响。结果表明：与未处理碳纳米管相比,酸处理的碳纳米管增加了环氧／石墨复合材料的弯曲强度和硬度,降低了电阻率。酸处理的碳纳米管增强环氧／石墨复合材料的弯曲强度达到21．9MPa,比未添加碳纳米管时提高了近22％;同时复合材料的硬度达到最大值21．7HS,比未添加碳纳米管时提高了近10％;复合材料的电阻率达到了最小值45036μΩ·cm,比未添加碳纳米管时复合材料的电阻率降低了近17％。     

Orientation of carbon nanotubes in polypropylene melt

The correlation between shear stress and the orientation of single‐walled carbon nanotubes (SWCNTs) in an SWCNT/polypropylene composite during the melt process was investigated. Highly oriented composite fibers were produced by extruding the polypropylene melt using a capillary rheometer. The experimental range of shear rates covered those of common polymer melt‐shaping processes. The effect of functionalization of the SWCNTs on orientation was also investigated. Polarized Raman spectroscopy was used to analyze the orientation of the SWCNTs. A high degree of SWCNT orientation was observed under high shear stress, and the functionalized SWCNTs induced a higher degree of orientation than did pristine SWCNTs. The existence of a critical shear stress was observed for the orientation of the SWCNTs, and their orientation was found to occur more efficiently above this critical shear stress. The crystallization temperature and heat of fusion were characterized using a differential scanning calorimeter, and both parameters were observed to increase with the incorporation of SWCNTs. © 2012 Society of Chemical Industry     

Enhanced electrical properties by tuning the phase morphology of multiwalled carbon nanotube‐filled poly(ether ether ketone)/polyimide composites

A novel high‐performance material with enhanced electrical properties was obtained by tuning the phase morphology of poly(ether ether ketone) (PEEK)/thermoplastic polyimide (TPI)/multiwalled carbon nanotube (MWCNT) composites. MWCNTs were selectively located in the TPI phase due to discrepant affinity of MWCNTs between PEEK and TPI. The dependence of the electrical properties of the PEEK/TPI/MWCNT composites on the phase morphology was investigated by changing the PEEK/TPI ratio, and the maximum conductivity was achieved with a PEEK/TPI ratio of 50/50, which could be explained by the selective location of MWCNTs and the co‐continuous phase morphology of the composites. © 2015 Society of Chemical Industry     

Preparation and characterization of polydiphenylamine/multi‐walled carbon nanotube composites

We describe the synthesis of methane sulfonic acid (MeSA)‐doped poly(diphenylamine) (PDPA) with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) via in situ polymerization. Diphenylamine monomers were adsorbed on to the surface of c‐MWNTs and polymerized to form PDPA/c‐MWNT composites. SEM and TEM images indicated two different types of materials: the thinner fibrous phase and the larger globular phase. The individual fibrous phase had a diameter around 100–130 nm, which should be the carbon nanotubes (diameter 20–30 nm) coated with a PDPA layer. The structure of PDPA/c‐MWNT composites was characterized by FTIR, UV‐visible spectroscopy and X‐ray diffraction patterns. The electrical conductivities of PDPA/c‐MWNT composites were much higher than that of PDPA without c‐MWNTs. Copyright © 2006 Society of Chemical Industry     

多壁碳纳米管/聚酰亚胺复合材料制备及其性能研究

聚酰亚胺的前聚体,聚酰胺酸,是通过4,4-二氨基二苯醚(ODA)与3,3,4,4二苯甲酮四羧酸二酐(BTDA)反应制备的.未改性的、酸改性和胺改性的多壁碳纳米管(MWCNT)被分别地单独加入到聚酰胺酸溶液中,并加热至300℃,从而制成聚酰亚胺/碳纳米管复合材料.扫描型电子显微镜(SEM)和透射电子显微镜(TEM)的显微...     

Preparation and thermal,electrical, and morphological properties of multiwalled carbon nanotubeand epoxy composites

Multiwalled carbon nanotube (MWCNT)/epoxy composites are prepared, and the characteristics and morphological properties are studied. Scanning electron microscopy microphotographs show that MWCNTs are dispersed on the nanoscale in the epoxy resin. The glass‐transition temperature (T_g) of MWCNT/epoxy composites is dramatically increased with the addition of 0.5 wt % MWCNT. The T_g increases from 167°C for neat epoxy to 189°C for 0.5 wt % CNT/epoxy. The surface resistivity and bulk resistivity are decreased when MWCNT is added to the epoxy resins. The surface resistivity of CNT/epoxy composites decreases from 4.92 × 10¹² Ω for neat epoxy to 3.03 × 10⁹ Ω for 1 wt % MWCNT/epoxy. The bulk resistivity decreases from 8.21 × 10¹⁶ Ω cm for neat epoxy to 6.72 × 10⁸ Ω cm for 1 wt % MWCNT/epoxy. The dielectric constant increases from 3.5 for neat epoxy to 5.5 for 1 wt % MWCNT/epoxy. However, the coefficient of thermal expansion is not affected when the MWCNT content is less than 0.5 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1272–1278, 2007     

Evaluation of electrical conductivity models for conductive polymer composites

The electrical conductivity of polymeric materials can be increased by the addition of carbon fillers, such as carbon fibers and graphite. The resulting composites could be used in applications such as interference shielding and electrostatic dissipation. Electrical conductivity models are often proposed to predict the conductivity behavior of these materials in order to achieve more efficient material design that could reduce costly experimental work. The electrical conductivity of carbon‐filled polymers was studied by adding four single fillers to nylon 6,6 and polycarbonate in increasing concentrations. The fillers used in this project include chopped and milled forms of polyacrylonitrile (PAN) carbon fiber, Thermocarb^TM Specialty Graphite, and Ni‐coated PAN carbon fiber. Material was extruded and injection‐molded into test specimens, and then the electrical conductivity was measured. Data analysis included a comparison of the results to existing conductivity models. The results show that the model proposed by Mamunya, which takes into account the filler aspect ratio and the surface energy of the filler and polymer, most closely matched the conductivity data. This information will then be used in the development of improved conductivity models. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1341–1356, 2002     

Preparation and properties of the single‐walled carbon nanotube/cellulose nanocomposites using N‐methylmorpholine‐N‐oxide monohydrate

Single‐walled carbon nanotube (SWNT)/cellulose nanocomposite films were prepared using N‐methylmorpholine‐N‐oxide (NMMO) monohydrate as a dispersing agent for the acid‐treated SWNTs (A‐SWNTs) as well as a cellulose solvent. The A‐SWNTs were dispersed in both NMMO monohydrate and the nanocomposite film (as confirmed by scanning electron microscopy) because of the strong hydrogen bonds of the A‐SWNTs with NMMO and cellulose. The mechanical properties, thermal properties, and electric conductivity of the nanocomposite films were improved by adding a small amount of the A‐SWNTs to the cellulose. For example, by adding 1 wt % of the A‐SWNTs to the cellulose, tensile strain at break point, Young's modulus, and toughness increased ～ 5.4, ～ 2.2, and ～ 6 times, respectively, the degradation temperature increased to 9°C as compared with those of the pure cellulose film, and the electric conductivities at ? (the wt % of A‐SWNTs in the composite) = 1 and 9 were 4.97 × 10^?4 and 3.74 × 10^?2 S/cm, respectively. Thus, the A‐SWNT/cellulose nanocomposites are a promising material and can be used for many applications, such as toughened Lyocell fibers, transparent electrodes, and soforth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A representative and comprehensive review of the electrical and thermal properties of polymer composites with carbon nanotube and other nanoparticle fillers

In this review we present the results of our literature investigation into the electrical and thermal properties of carbon nanotube polymer composites. A short selection of data relating to conductive polymer composites with various fillers is provided for comparison. The effects of filler properties such as type and size, the use of hybrid fillers, fabrication methods for polymer composites and the importance of the modeling of the electronic and thermal transport mechanisms are discussed, as are more general factors influencing the properties of these composites. This review represents a comprehensive survey and constructive study and should serve as a useful reference tool for industrial and academic researchers working in this field. © 2017 Society of Chemical Industry