Resultant synergism in the shear resistance of acrylic pressure‐sensitive adhesives prepared by emulsion polymerization of n‐butyl acrylate/2‐ethyl hexyl acrylate/acrylic acid

Acrylic emulsion pressure‐sensitive adhesives (PSAs) were synthesized by the copolymerization of n‐butyl acrylate with various levels of 2‐ethyl hexyl acrylate (2EHA) and a small constant amount of acrylic acid. The effect of varying the n‐butyl acrylate/2EHA monomer composition on the kinetic behavior of the polymerization and the characteristics of the copolymers prepared in a batch process were investigated. The results showed that increasing the amount of 2EHA in the monomer caused the polymerization rate and the glass‐transition temperature of the acrylic copolymers to decrease. Increasing the amount of 2EHA caused the gel content of the copolymers to decrease, reaching a minimum at 50 wt %; thereafter, the gel content increased at higher 2EHA levels. For the acrylic emulsion, the peel‐fracture energy of the PSAs decreased as the amount of 2EHA in the monomer was increased up to 50 wt %. At higher 2EHA levels, the peel‐fracture energy was relatively constant. Interestingly, a synergistic effect of increased shear resistance at 25 wt % 2EHA was observed without a significant trade‐off in terms of the peel and tack properties. This behavior was attributed to a good interconnection between the microgels and the free polymer chains inside the contacting particles in the adhesive film. Cooperation between various levels of 2EHA in the copolymer structure simultaneously changed the crosslink molecular weight (M_c) of the microgels and the entanglement molecular weight (M_e) of the free chains in the adhesive network morphology. The adhesive performance of the PSAs was found to be correlated with their M_c/M_e values as the 2EHA proportion was varied. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of polyurethane acrylates by hydrogenated castor oil and dimer‐based polyester diol and study on pressure‐sensitive adhesive

Synthesis of polyurethane acrylate (PUA) and preparation of the UV‐cured pressure‐sensitive adhesives (PSA) are reported. Molecular weight (M_w) (by gel permeation chromatography) and viscosity (η*) of PUA were measured. Characterization of PUA and PSA before and after UV‐curing was made by FTIR. Increase of the hydroxyls from hydrogenated castor oil/hydroxyls from dimer‐based polyester diol (OH_HCO/OH_Diol) ratio decreased the M_w and η* value of PUA. Dynamic viscoelastic properties (by dynamic rheological spectrometer) and performance of the UV‐cured PSA were also studied. Increase of the OH_HCO/OH_Diol ratio increased the storage modulus (G′), the loss modulus (G″), and complex viscosity (Eta*) of the UV‐cured PSA, which, in turn, enhanced holding power and shear adhesion failure temperature (SAFT) and yet decreased peeling strength. Substitution of OB for DBTDL depressed the M_w and η* value of PUA, while the G″ and Eta* values of the UV‐cured PSA were elevated, which, in turn, increased the holding power and SAFT and yet depressed the peeling strength. Elevation of the tackifying resin content depressed the G′, G″, and Eta* values of the cured PSA and yet increased glass transition temperatures (T_g) of PSA, measured by differential scanning calorimetry. Peeling strength of PSA elevated as increasing the tackifying resin, while the holding power and SAFT fell. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1814–1821, 2005     

Synthesis and characterization of ternary‐copolymer of soluble fluorinated polyimides based on 1,4‐bis (4‐amino‐2‐trifluoromethylphenoxy) benzene

A series of novel ternary‐copolymer of fluorinated polyimides (PIs) were prepared from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (pBATB), commercially available aromatic dianhydrides, and aromatic diamines via a conventional two‐step thermal or chemical imidization method. The structures of all the obtained PIs were characterized with FTIR, ¹H‐NMR, and element analysis. Besides, the solubility, thermal stability, mechanical properties, and moisture uptakes of the PIs were investigated. The weight‐average molecular weight (M_w) and the number‐average molecular weight (M_n) of the PIs were determined using gel‐permeation chromatography (GPC). The PIs were readily dissolved not only in polar solvents such as DMF, DMAc, and NMP, but also in some common organic solvents, such as acetic ester, chloroform, and acetone. The glass transition temperatures of these PIs ranged from 201 to 234°C and the 10% weight loss temperatures ranged from 507 to 541°C in nitrogen. Meanwhile, all the PIs left around 50% residual even at 800°C in nitrogen. The GPC results indicated that the PIs possessed moderate‐to‐high number‐average molecular weight (M_n), ranging from 9609 to 17,628. Moreover, the polymer films exhibited good mechanical properties, with elongations at break of 8–21%, tensile strength of 66.5–89.8 MPa, and Young's modulus of 1.04–1.27 GPa, and low moisture uptakes of 0.54–1.13%. These excellent combination properties ensure that the polymer could be considered as potential candidates for photoelectric and microelectronic applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Schiff base‐substituted polyphenol: synthesis,characterisation and non‐isothermal degradation kinetics

BACKGROUND: Polymers of phenols and aromatic amines have emerged as new materials in fields such as superconductors, coatings, laminates, photoresists and high‐temperature environments. The stability, kinetics and associated pollution of the thermal decomposition of oligophenols are of interest for the aforementioned fields. RESULTS: A new Schiff base polymer, derived from N,N′‐bis(2‐hydroxy‐3‐methoxyphenylmethylidene)‐2,6‐pyridinediamine, was prepared by oxidative polycondensation. Characterisations using Fourier transform infrared, UV‐visible, ¹H NMR and ¹³C NMR spectroscopy, thermogravimetric/differential thermal analysis, gel permeation chromatography, cyclic voltammetry and conductivity measurements were performed. The number‐average (M_n) and weight‐average molecular weight (M_w) and dispersity (D = M_w/M_n) of the polymer were found to be 61 000 and 94 200 g mol^?1 and 1.54, respectively. Apparent activation energies of the thermal decomposition of the polymer were determined using the Tang, Flynn–Wall–Ozawa, Kissinger–Akahira–Sunose and Coats–Redfern methods. The most likely decomposition process was a D_n deceleration type in terms of the Coats–Redfern and master plot results. CONCLUSION: The mechanism of the degradation process can be understood through the use of kinetic parameters obtained from various non‐isothermal methods. Copyright © 2009 Society of Chemical Industry     

Synthesis,physical properties,and characterization of starch‐based blend films by adding nano‐sized TiO2/poly(methyl metacrylate‐co‐acrylamide)

The purpose of this study was to improve the physical properties and to expand the application range of starch‐based blend films added nano‐sized TiO₂/poly(methyl methacrylate‐co‐acrylamide) (PMMA‐co‐AM). Starch‐based blend films were prepared by using corn starch, polyvinyl alcohol (PVA), nano‐sized PMMA‐co‐AM, nano‐sized TiO₂/PMMA‐co‐AM particles, and additives, i.e., glycerol (GL) and citric acid (CA). Nano‐sized PMMA‐co‐AM was synthesized by emulsion polymerization and TiO₂ nanoparticles were also prepared by using sol–gel method. Nano‐sized TiO₂/PMMA‐co‐AM particles were synthesized by wet milling for 48 h. The morphology and crystallinity of TiO₂, nano‐sized PMMA‐co‐AM and TiO₂/PMMA‐co‐AM particles were investigated by using the scanning electron microscope (SEM) and X‐ray diffractometer (XRD). In addition, the functional groups of the TiO₂/PMMA‐co‐AM particles were characterized by IR spectrophotometry (FTIR). The physical properties such as tensile strength (TS), elongation at break (%E), degree of swelling (DS), and solubility (S) of starch‐based films were evaluated. It was found that the adding of nano‐sized particles can greatly improve the physical properties of the prepared films. The photocatalytic degradability of starch/PVA/nano‐sized TiO₂/PMMA‐co‐AM composite films was evaluated using methylene blue (MB) and acetaldehyde (ATA) as photodegradation target under UV and visible light. The degree of decomposition (C/C₀) of MB and ATA for the films containing TiO₂ and CA was 0.506 and 0.088 under UV light irradiation and 0.586 (MB) and 0.631 (ATA) under visible light irradiation, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of novel polymethacrylate bearing an (S)‐(+)‐1‐cyclohexylethyl urea group in the side chain and its chiral recognition ability

A new chiral methacrylate, (S)‐(+)‐1‐cyclohexylethyl‐(2‐methacryloyloxyethyl)urea (CEMOU), was synthesized from 2‐methacryloyloxyethyl isocyanate (MOI) and (S)‐(+)‐cyclohexylethylamine. Radical homopolymerization of CEMOU was performed in several solvents to obtain the corresponding chiral polymers having hydrogen bonds based on urea moieties. Specific optical rotations of poly(CEMOU) were slightly changed by the measurement temperature, which may be attributed in part to a change of conformation caused by hydrophobic interaction between the cyclohexyl groups. From the results of radical copolymerization of CEMOU (M₁) with styrene (ST, M₂) or methyl methacrylate (MMA, M₂), monomer reactivity ratios (r₁, r₂) and Alfrey–Price Q–e values were determined: r₁ = 0.89, r₂ = 0.12, Q₁ = 2.45, e₁ = 0.68 for the CEMOU–ST system; r₁ = 0.48, r₂ = 0.18, Q₁ = 8.39, e₁ = 1.97 for the CEMOU–MMA system. The chiroptical property of the poly(CEMOU‐co‐ST) was slightly influenced by the co‐units. Poly(CEMOU)‐bonded silica gel as the chiral stationary phase (CSP) was prepared for high‐performance liquid chromatography (HPLC). The CSP resolved trans‐2‐dibenzyl‐4,5‐di(o‐hydroxyphenyl)‐1,3‐dioxolane in normal phase such as n‐hexane/2‐propanol by HPLC. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1018–1025, 2003     

Polymer gel electrolytes prepared from P(EG‐co‐PG) and their nanocomposites using organically modified montmorillonite

Polymer gel electrolytes were prepared by thermal crosslinking reaction of a series of acrylic end‐capped poly(ethylene glycol) and poly(propylene glycol) [P(EG‐co‐PG)] having various geometries and molecular weights. Acrylic end‐capped prepolymers were prepared by the esterification of low molecular weight (M_n: 1900–5000) P(EG‐co‐PG) with acrylic acid. The linear increase in the ionic conductivity of polymer gel electrolyte films was observed with increasing temperature. The increase in the conductivity was also monitored by increasing the molecular weight of precursor polymer. Nanocomposite electrolytes were prepared by the addition of 5 wt % of organically modified layered silicate (montmorillonite) into the gel polymer electrolytes. The enhancement of the ionic conductivity as well as mechanical properties was observed in the nanocomposite systems. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 894–899, 2004     

Rheological behavior of pH‐responsive associating ionic polymers of diallyammonium salts and sulfur dioxide

In this study, the viscoelastic behavior of hydrophobically modified polyelectrolytes obtained from the hydrolysis of cationic acid salts (CAS's) as a function of their zwitterion fraction (x) and anion fraction (z) was studied. The dynamic viscosity (η′) dependence on frequency of polymer solutions of polybetaine/anionic polyelectrolyte (APE) with various compositions of x and z in 0.1N NaCl showed typical shear thinning behavior. η′ of a solution of CAS 4 (M₂‐4 (4 mol % hydrophobe)) attained a maximum value in the presence of 1.67 equiv of NaOH (corresponding to an x : z ratio of 33 : 67) and decreased with any further addition of NaOH. We suggest this maximum to be a result of a combined effect of coil expansion and hydrophobic association. The influence of the temperature and concentration on η′ of CAS 4 (M₂‐4) treated with 1.67 equiv of NaOH was also investigated. The rheology of CAS 4 (M₂‐4) samples treated with 1.67, 1.81, and 2.0 equiv of NaOH suggested a reversible network. However, for APE 7 (M₂‐5 (5 mol % hydrophobe)), elastic behavior was dominant, and the formation of highly interconnected three‐dimensional networks was suggested. At lower x : z ratios, the effect of coil expansion due to a higher APE fraction was more than counterbalanced by the lower degree of intermolecular hydrophobic associations, whereas at higher x : z ratios, coil contraction became the predominant effect. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Organic‐acid‐catalyzed sol–gel route for preparing poly(methyl methacrylate)–silica hybrid materials

In this study, a series of organic–inorganic hybrid sol–gel materials consisting of a poly(methyl methacrylate) (PMMA) matrix and dispersed silica (SiO₂) particles were successfully prepared through an organic‐acid‐catalyzed sol–gel route with N‐methyl‐2‐pyrrolidone as the mixing solvent. The as‐synthesized PMMA–SiO₂ nanocomposites were subsequently characterized with Fourier transform infrared spectroscopy and transmission electron microscopy. The solid phase of organic camphor sulfonic acid was employed to catalyze the hydrolysis and condensation (i.e., sol–gel reactions) of tetraethyl orthosilicate in the PMMA matrix. The formation of the hybrid membranes was beneficial for the physical properties at low SiO₂ loadings, especially for enhanced mechanical strength and gas barrier properties, in comparison with the neat PMMA. The effects of material composition on the thermal stability, thermal conductivity, mechanical strength, molecular permeability, optical clarity, and surface morphology of the as‐prepared hybrid PMMA–SiO₂ nanocomposites in the form of membranes were investigated with thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, gas permeability analysis, ultraviolet–visible transmission spectroscopy, and atomic force microscopy, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Balance of mechanical and electrical performance in polyimide/nano titanium dioxide prepared by an in‐sol method

Hybrid polyimide (PI)/titanium dioxide (TiO₂) films were prepared by in situ polymerization and sol–gel and in‐sol methods (where in‐sol method indicates that in situ polymerization and the sol–gel method were used in the same samples). The mechanical and electrical properties were found to be sensitive to the processing methods and the dispersion of nano titanium dioxide (nano‐TiO₂) in the PI matrix. For the PI/TiO₂ films prepared by the in situ polymerization method, their tensile strength increased with increasing TiO_{2‐in situ} (“TiO_{2‐in situ}” is “the TiO₂ nano‐particles prepared by in situ polymerization method”) concentration. However, the optimal corona lifetime of the PI/TiO₂ films was 15 min at 20 kHz and 2 kV because of poor dispersion. For the PI/TiO₂ films prepared by the sol–gel method, the corona lifetime reached 113 min because of superior dispersion and a tensile strength of about 19.63 MPa. A balance of mechanical and electrical performances was achieved with the in‐sol method. The corona‐resistant life of the PI/TiO₂ films was 43 min, which was about six times longer than that of the neat PI. Their tensile strength was 83.5 MPa; these films showed no decrease in this value compared with the pure PI films. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44666.     

Effect of 3‐aminopropyltriethoxysilane on properties of poly(butyl acrylate‐co‐maleic anhydride)/silica hybrid materials

The transparent poly(butyl acrylate‐co‐maleic anhydride)/silica [P(BA‐co‐MAn)/SiO₂] has been successfully prepared from butyl acrylate‐maleic anhydride copolymer P(BA‐co‐MAn) and tetraethoxysilane (TEOS) in the presence of 3‐aminopropyltriethoxysilane (APTES) by an in situ sol–gel process. Triethoxysilyl group can be readily incorporated into P(BA‐co‐MAn) as pendant side chains by the aminolysis of maleic anhydride unit of copolymer with APTES, and then organic polymer/silica hybrid materials with covalent bonds between two phases can be formed via the hydrolytic polycondensation of triethoxysilyl group‐functionalized polymer with TEOS. It was found that the amount of APTES could dramatically affect the gel time of sol–gel system, the sol fraction of resultant hybrid materials, and the thermal properties of hybrid materials obtained. The decomposition temperature of hybrid materials and the final residual weight of thermogravimetry of hybrid both increase with the increasing of APTES. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) showed that the morphology of hybrid materials prepared in the presence of APTES was a co‐continual phase structure. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 419–424, 1999     

Rheological and adhesion properties of acrylic pressure‐sensitive adhesives

Different pressure‐sensitive adhesives (PSAs) based on acrylic monomers were synthesized under different reaction conditions. The synthesized PSAs have good adhesive properties and without leaving any residue can be easily peeled off from the surface of a substrate. The relationship between PSAs rheological behavior and its adhesion properties (e.g., peel, tack, and shear resistance) has been studied at constant adhesive thickness. The samples were examined for their surface energy and viscoelastic characteristics. It was observed that increase in reaction temperature and reaction time results in decreased storage modulus due to lowered molecular weight, which finally leads to lower elasticity of the PSA. While the storage (G′) and loss (G″) modulus of samples increase with increased initiator concentration, the elasticity of PSA is increased as well. High G″ at high frequency (100 Hz) represents high peel strength because of higher dissipation of viscoelastic energy during debonding. The tack values increase by lowering storage modulus at 1 Hz due to higher M_e. Shear values are increased by higher storage modulus at low frequency (0.1 Hz) due to hydrogen bonding of the different components. Some parallel investigations on the surface energy of the samples showed that they have different properties because of the nature of different monomeric units with their corresponding orientations. Our results reveal that the peel strength is not affected by surface energy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Modification research on the peel strength of the acrylate emulsion pressure‐sensitive adhesives

Pressure‐sensitive adhesives (PSAs) were produced with latexes synthesized via starved semibatch emulsion polymerization processes with butyl acrylate, three different kinds of hard monomers [styrene (St), methyl methacrylate, and 2‐phenoxy ethyl methacrylate (SR340)], acrylic acid, and 2‐hydroxy ethyl acrylate. The management of both the copolymer composition and the polymerization process allowed us to control the behavior of the PSAs. For the acrylate latexes, the types of hard monomers and their contents, the concentration of buffer [bicarbonate (NaHCO₃)], and three kinds of semibatch processes were manipulated to modify the polymer properties. The performance of the PSA films cast from these latexes was evaluated by the peel strength. The results show that the PSA prepared with St exhibited the highest peel strength among the three hard monomers, and the latex synthesized by SR340 showed the largest gel content compared with the other two hard monomers. With increasing buffer, the latex particle size increased, and the peel strength initially increased to a maximum and then decreased. Nevertheless, the stability of the latexes decreased with increasing buffer concentration. In addition, the effects of the three kinds of semibatch processes on the peel strength of the PSA were also evaluated. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40095.     

Rheological evolution of a particular sol‐gel system

Rheological measurements and results discussed in this paper made on gelling mass containing thetraethoxysilane (TEOS or Si(OC₂H₅)₄) and calcium nitrate as sol‐gel precursors is important because of the interest of sol‐gel processes as a possible preparation route of glasses and amorphous body structures (sol‐gel route). The rheological measurements in our study, have been made to investigate the sol‐gel transition of Si(OC₂H₅)₄ by measuring the viscosity evolution at time intervals and temperature values established. The temperature dependence of the viscosity was used to determine the activation energies of the flow.     

High oil‐absorptive composites based on 4‐tert‐butylstyrene‐EPDM‐divinylbenzene graft polymer

4‐tert‐Butylstyrene‐EPDM‐divinylbenzene graft polymer (PBED) was prepared by graft crosslinking polymerization in toluene using BPO as an initiator. Gel and sol of PBED were isolated by extraction with tetrahydrofuran (THF). Sol PBED can be reused as oil absorbent through cross‐linking by ultraviolet irradiation. After swelling in oil, crosslinked polymers have poor gel strength to be taken out of oil wholly at high absorbency, although they possess strong mechanical strength in their dry states. As known, composite technique is one of the useful methods for material reinforcement. Fibres, sponges and non‐woven fabrics were used as reinforcers or supporters in this work. Oil absorbency was measured by method ASTM (F726‐81) and swelling kinetics of the composite was evaluated by an experimental equation. The gel strength parameter S, the relaxation exponent n, and the fractal dimension d_f of polymer and some composites in pseudo‐critical gel state were determined from oscillatory shear measurements by a dynamic rheometer. Mechanical properties and the morphologies of some composites were measured with a tensile tester and scanning electron microscopy, respectively. © 2001 Society of Chemical Industry     

UV‐curable methacrylic epoxy dispersions for cationic electrodeposition coating

UV‐curable epoxy dispersions were prepared for cationic electrodeposition coating. Sequential reactions were used to introduce methacrylate groups to the epoxy‐amine polymer as coupling agents to the multifunctional acrylates. The molecular weight values of the prepared epoxy‐amine polymer were M_n = 2800 and M_w = 4300. The neutralized epoxy‐amine polymer containing photoinitiator with or without multifunctional acrylate (pentaerythritol triacrylate, PETA) could be dispersed into a stable dispersion without any phase separation. The size of the particles in these epoxy dispersions was approximately 77.7 nm, and increased with the incorporation of PETA. The electrodeposition process was introduced to the prepared epoxy dispersions, and the electrodeposited films were cured by UV irradiation after a 10‐min flash off at 80°C. Studies of the kinetics using photo‐DSC revealed that the crosslinked films containing PETA gave a higher conversion rate than those without PETA, resulting in better resistance to methyl ethyl ketone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5566–5570, 2006     

High lithium ionic conductivity in the garnet‐type oxide Li7−2xLa3Zr2−xMoxO12 (x=0‐0.3) ceramics by sol‐gel method

Lithium garnet‐type oxides Li_7?2xLa₃Zr_2?xMo_xO₁₂ (x=0, 0.1, 0.2, 0.3) ceramics were prepared by a sol‐gel method. The influence of molybdenum on the structure, microstructure and conductivity of Li₇La₃Zr₂O₁₂ were investigated by X‐ray diffraction, scanning electron microscopy, and impedance spectroscopy. The cubic phase Li₇La₃Zr₂O₁₂ has been stabilized by partial substitution of Mo for Zr at low temperature. The introduction of Mo (x≥0.1) can accelerate densification. Li_6.6La₃Zr_1.8Mo_0.2O₁₂ sintered at lower temperature 1100°C for 3 hours exhibits highest total ionic conductivity of 5.09 × 10^?4 S/cm. Results indicate that the Mo doping LLZO synthesized by sol‐gel method effectively lowers its sintering temperature and improves the ionic conductivity.     

Synthesis of poly(methyl methacrylate‐g‐glycidyl azide) graft copolymers using N,N‐dithiocarbamate‐mediated iniferters

A glycidyl azide polymer with pendent N, N‐diethyl dithiocarbamate groups (GAP‐DDC) was prepared by the reaction of poly(epichlorohydrin) (PECH) with pendent N, N‐diethyl dithiocarbamate groups (PECH‐DDC) and sodium azide (NaN₃) in dimethylformamide (DMF). It was then used as a macro‐photoinitiator for the graft polymerization of methyl methacrylate (MMA). Photopolymerization was carried out in a photochemical reactor at a wavelength greater than 300 nm. Conversion was determined gravimetrically and first‐order time conversion plot for the polymerization system showed linear increase with the polymerization time indicating that polymerization proceed in controlled fashion. The molecular weight distribution (M_w/M_n) was in the range of 1.4–1.6 during polymerization. The formation of poly(methyl methacrylate‐g‐glycidyl azide) (PMMA‐g‐GAP) graft copolymer was characterized by gel permeation chromatography, FT‐IR spectroscopy, Thermogravimetric analysis, and differential scanning calorimetry. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Sol–gel process of alkoxysilane in emulsifier‐involved aqueous emulsions: A one‐pot synthetic route to emulsions of core‐shell composite particles and their applications

In this work, a one‐pot route to prepare emulsions of silica/polymer core‐shell composite particles was developed through the direct sol–gel processing of alkoxysilane on the surface of newly synthesized template polymer particles in emulsifier‐involved aqueous emulsions. It included two continuous steps: first, the polymer emulsions were synthesized through emulsion polymerization, and second, the template particles in the emulsions were directly coated with silica via sol–gel reaction of precursors without adding ethanol or removing emulsifiers. The size and morphology of the composite particles were characterized, and the results showed that the silica/polymer composite particles with core‐shell structure could be prepared only on the basis of cationic template emulsions, and the in situ‐coating reaction of sol–gel precursors carried on easier with the increasing of the positive charge density on the surface of template particles. The films formed from the composite emulsions were found to have superior optical and flame‐retardant properties compared to polymer films, owing to the core‐shell composite microstructure of the particles. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of CuBr2 salt treatment on the performance of nanocolloidal PPy:PSS multilayer thin film counter electrodes of dye‐sensitized solar cells

A thin Pt layer on fluorine‐doped tin oxide (FTO) glass is commonly used as the counter electrode (CE) for dye‐sensitized solar cells (DSCs). We have investigated thin layers on FTO glass made from spherical polypyrrole (PPy)–poly(styrene sulfonate) (PSS) nanocolloidal particles with and without treatment of CuBr₂ and used them as CEs. The colloidal polymer composite (PPy:PSS) was spin‐coated at 4000 rpm, and PPy:PSS multilayer (one, three, five) films were employed as the CEs. Aqueous solutions of CuBr₂ (0.5 M and 1 M) were coated onto the multilayer CEs, which increased the efficiency of DSCs. When compared with the untreated PPy:PSS counter electrodes, the CuBr₂‐treated PPy:PSS films showed lower charge‐transfer resistance, higher surface roughness, and improved catalytic performance for the reduction of . The enhanced catalytic performance is attributed to the interaction of the superior electrocatalytic activity of PPy:PSS and CuBr₂ salt. Under standard AM 1.5 sunlight illumination, the counter electrodes based on a single‐layer PPy:PSS composite with 0.5 M and 1 M CuBr₂ salt treatment demonstrated power conversion efficiencies (PCE) of 5.8% and 5.6%, respectively. These values are significantly higher than that of the untreated PPy:PSS CE and are comparable with that of a Pt CE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43772.