Separation of toluene–methanol mixtures by pervaporation using crosslink IPN membranes

Polyvinyl alcohol (PVOH) has been chemically modified by crosslink copolymerization of acrylic acid (AA) and hydroxyethylmethacrylate (HEMA) in aqueous solution of PVOH and finally crosslinking PVOH to produce a full interpenetrating network (IPN) membrane termed as PVAH. Accordingly, three such full crosslink IPNs membranes, i.e. PVAHI, PVAHII and PVAHIII containing varied weight ratio of PVOH and copolymer have been synthesized and used for pervaporative separation of methanol from its mixtures with toluene. For comparison, a conventional PVOH membrane crosslinked with glutaraldehyde has also been used for the same pervaporation study. The flux and selectivity of these IPN membranes were found to be much higher than the conventional glutaraldehyde crosslinked PVOH membrane. Among the three membranes, PVAHII with 50 wt% polyAH incorporation showed optimum performance in terms of flux and methanol selectivity.     

Synthesis of full interpenetrating network membranes of poly(acrylic acid-co-acrylamide) in the matrix of polyvinyl alcohol for dehydration of ethylene glycol by pervaporation

Polyvinyl alcohol (PVOH) has been chemically modified by crosslink copolymerization of acrylic acid (AA) and acrylamide (AM) in aqueous solution of PVOH and finally crosslinking the copolymer with methylene bis acrylamide (MBA) and PVOH with glutaraldehyde to produce a full interpenetrating network (FIPN) membrane. Accordingly, three such fully crosslinked IPNs i.e. FIPN25, FIPN50 and FIPN75 have been synthesized with different mass ratio of PVOH:copolymer i.e. 1:0.25 (FIPN25), 1:0.50 (FIPN50) and 1:0.75 (FIPN75). These full IPN membranes were used for pervaporative dehydration of ethylene glycol (EG). All of these IPN membranes were characterized with various conventional methods like FTIR, mechanical properties, DTA and SEM. The performances of the membranes were evaluated in terms of sorption and pervaporative dehydration of EG. The IPN membranes were found to show preferential sorption and diffusion for water. Flux and water selectivity of these membranes were found to increase with increasing amount of copolymer in PVOH matrix. However, among the three membranes, FIPN75 were found to show the highest flux but lower selectivity for water while FIPN50 membrane showed optimum performance in terms of both flux and selectivity. Diffusion coefficient and plasticization interaction of water and EG through all the IPN membranes were determined using modified solution-diffusion model.     

Synthesis of Novel Polymeric Membrane for Separation of MTBE-Methanol by Pervaporation

Abstract

Polyvinyl alcohol(PVOH) has been chemically modified by crosslinking copolymerization of acrylic acid(AA) and hydroxyethylmethacrylate (HEMA) in aqueous solution of PVOH and finally crosslinking PVOH with glutaraldehyde to produce a full interpenetrating network(IPN) membrane. Accordingly, three such full crosslink IPNs i.e., PVAHI, PVAHII and PVAHIII have been synthesized with different weight ratio of PVOH:Poly (AA-co-HEMA) i.e., 1:0.25 (PVAHI), 1:0.50 (PVAHII) and 1:0.75 (PVAHIII). These IPN membranes have been used for pervaporative separation of MTBE-methanol mixtures. All the PVAH membranes were also characterized with various conventional methods like FTIR, mechanical properties, DSC and TGA. Permeability and methanol selectivity of these membranes were found to increase with increasing amount of copolymer in PVOH matrix. However, among the three membranes, PVAHIII were found to show the highest flux but lower selectivity for methanol while PVAHII membrane showed optimum performance in terms of both flux and selectivity.     

Swelling dynamics of IPN hydrogels including acrylamide‐acrylic acid‐chitosan and evaluation of their potential for controlled release of piperacillin‐tazobactam

For to be used in controlled releasing of piperacillin‐tazobactam, a series of semi and full IPN type hydrogels composed of acrylic acid (AA), acrylamide (AAm) and Chitosan (CS) were prepared via free‐radical polymerization. Ethylene glycol dimethacrylate (EGDMA) was used for crosslinking of PAAm and PAA chains to form semi‐IPN hydrogels. However, the full‐IPN type hydrogels were prepared by using glutaraldehyde (GA) and EGDMA as cocrosslinkers. Characteristics of the hydrogels were investigated by swelling experiments and SEM and FTIR analysis. Generally, full‐IPN type hydrogels swell much more than the semi‐IPN types. By comparing the full‐IPN type hydrogels in between, it is found that the increasing amount of GA causes the decreasing in S% values from 4860 to 4300%. Releasing of piperacillin‐tazobactam from selected three hydrogels were investigated in phosphate buffer solution at pH = 7.4, 37°C. The kinetic release parameters, n and k were calculated and non‐Fickian type diffusion was established for these hydrogels. The behaviors of the piperacillin‐tazobactam loaded hydrogels in Staphylococcus aureus (S. aureus) and Pseudomonas aeruginosa (P. aeruginosa) culture suspensions were also studied and the statistically significant differences for the microorganism growth values were determined. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of Chemically Modified Polyvinyl Alcohol Membranes for Dehydration of Dioxane by Pervaporation

Abstract

Polyvinyl alcohol (PVOH) has been chemically modified by polymerizing hydroxyethylmethacrylate (HEMA) in aqueous solution of PVOH and finally crosslinking PVOH with glutaraldehyde to produce a semi-interpenetrating network (SIPN) membrane. Accordingly, three such SIPNs i.e., SIPNI, SIPNII, and SIPNIII were synthesized with different weight ratio of PVOH: HEMA i.e., 1:0.25 (SIPNI), 1:0.50 (SIPNII) and 1:0.75 (SIPNIII). These SIPN membranes were used for pervaporative dehydration of dioxane. PVOH without any chemical modification but crosslinked with the same amount of glutaraldehyde has also been used for this study for comparison. All the SIPN membranes were also characterized with various conventional methods like mechanical properties, DSC and TGA. Water permeability and water selectivity of the IPN membranes were found to be much higher than those of the crosslinked PVOH membrane which was not chemically modified. The permeability of the membranes were also found to increase with increase in the HEMA content in PVOH matrix.     

Preparation of alginate/poly(N‐isopropylacrylamide) semi‐interpenetrating and fully interpenetrating polymer network hydrogels with γ‐ray irradiation and their swelling behaviors

Semi‐interpenetrating polymer network (semi‐IPN) and fully interpenetrating polymer network (full‐IPN) hydrogels composed of alginate and poly(N‐isopropylacrylamide) were prepared with γ‐ray irradiation. The semi‐IPN hydrogels were prepared through the irradiation of a mixed solution composed of alginate and N‐isopropylacrylamide (NIPAAm) monomer to simultaneously achieve the polymerization and self‐crosslinking of NIPAAm. The full‐IPN hydrogels were formed through the immersion of the semi‐IPN film in a calcium‐ion solution. The results for the swelling and deswelling behaviors showed that the swelling ratio of semi‐IPN hydrogels was higher than that of full‐IPN hydrogels. A semi‐IPN hydrogel containing more alginate exhibited relatively rapid swelling and deswelling rates, whereas a full‐IPN hydrogel showed an adverse tendency. All the hydrogels with NIPAAm exhibited a change in the swelling ratio around 30–40°C, and full‐IPN hydrogels showed more sensitive and reversible behavior than semi‐IPN hydrogels under a stepwise stimulus. In addition, the swelling ratio of the hydrogels continuously increased with the pH values, and the swelling processes were proven to be repeatable with pH changes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4439–4446, 2006     

Mechanical and dynamic mechanical studies of epoxy/VAc‐EHA/HMMM IPN–jute composite systems

Epoxy [50:50 mixture of Di‐Glycidyl Ether of Bis‐Phenol A (DGEBA) and Epoxidized Novolac (EPN)] was solution blended with Vinyl Acetate‐2‐ Ethylhexylacrylate (VAc‐EHA) resin in aqueous medium, in varying weight fractions, with Hexamethoxymethylmelamine (HMMM) as a crosslinker and data was compared with a control. The present work was aimed to optimize the tensile strength, dynamic mechanical strength, impact strength, and toughness by preparing a blend followed by jute composites of a semi‐ and full interpenetrating network (IPN). In control experiments epoxy alone was crosslinked (semi‐IPN), whereas the DGEBA‐EPN and VAc‐EHA/HMMM were crosslinked separately (full‐IPN), using jute as the substrate for making composites. Composites of full‐IPN systems of epoxy/VAc‐EHA system had higher moduli and UTS than the semi‐IPN systems. Dynamic mechanical study showed that full‐IPN systems have higher T_g values than semi‐IPN systems. The impact strength increases with increasing proportions of VAc‐EHA copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 958–963, 2004     

Preparation and Swelling Properties of Temperature‐Sensitive Semi‐Interpenetrating Polymer Networks Composed of Poly[(N‐tert‐butylacrylamide)‐co‐acrylamide] and Hydroxypropyl Cellulose

Summary: Temperature‐responsive hydrogels based on linear HPC and crosslinked P(NTBA‐co‐AAm) were prepared by the semi‐IPN technique. The structure of these semi‐IPN hydrogels was investigated by FT‐IR spectroscopy. An increase in normalized band ratios (A₂₉₈₀/A₁₆₆₅) was observed with increasing HPC content in the initial mixture. The swelling kinetics and water transport mechanism of these semi‐IPN hydrogels were examined and their temperature responsive behaviors were also investigated by measuring equilibrium swelling ratios and pulsatile swelling experiments. The results showed that these semi‐IPN hydrogels underwent a volume phase transition between 18 and 22 °C irrespective of the amounts of MBAAm and HPC. However, below the volume phase transition temperature, their equilibrium swelling ratios were affected by the amount of MBAAm and HPC. The pulsatile swelling experiments indicated that the lower the MBAAm and the higher HPC contents in semi‐IPN hydrogels the faster the response rate temperature change.

Equilibrium swelling ratios of the semi‐IPN P(NTBA‐co‐AAm)/HPC hydrogels in water shown as a function of temperature.     

Preparation and characterization of pH‐ and temperature‐responsive semi–interpenetrating polymer network hydrogels based on linear sodium alginate and crosslinked poly(N‐isopropylacrylamide)

In this study, pH‐ and temperature‐responsive hydrogels based on linear sodium alginate (SA) and crosslinked poly(N‐isopropylacrylamide) (PNIPAAm) were prepared by semi‐interpenetrating network (semi‐IPN) technique. The dually responsive hydrogels were characterized by FTIR, DSC, and SEM, and their temperature‐ and pH‐responsive behaviors were investigated by measuring equilibrium swelling ratios and pulsatile swelling experiments. The results showed that these hydrogels underwent volume phase transition at around 33°C irrespective of the pH value of the medium, but their pH sensitivity was evident only below their volume phase transition temperature. Under basic conditions, the swelling ratios of SA/PNIPAAm semi‐IPN hydrogels were greater than that of pure PNIPAAm hydrogel and increased with increasing SA content incorporated into the hydrogels, but the case was inverse under acidic conditions. The pulsatile swelling experiments indicated that the higher the SA content in SA/PNIPAAm semi‐IPN hydrogels, the faster the response rate to both pH and temperature change. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1931–1940, 2005     

Water and temperature response of semi‐IPN hydrogels composed of chitosan and polyacrylonitrile

Temperature‐responsive semi‐interpenetrating polymer networks (semi‐IPNs) constructed with chitosan and polyacrylonitrile (PAN) were crosslinked with glutaraldehyde. The semi‐IPN determined the sorption behavior of water at several temperatures and at a relative humidity (RH) of 95% using a dynamic vapor sorption (DVS) system. Water diffusion coefficients of semi‐IPNs were calculated according to the Fickian Law at several temperatures and exhibited a relatively water uptake, 0.1–0.4 at room temperature. The water uptake of hydrogels depended on temperature. The apparent activation energy was dependent of the composition of the semi‐IPN with value of 32.8–34.8 kJmol^?1. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 12: 2721–2724, 2003     

Synthesis and properties of the semi‐interpenetrating polymer network–like,thermosensitive poly(N‐isopropylacrylamide) hydrogel

A new strategy was used to prepare a semi‐interpenetrating polymer network (semi‐IPN)–like poly(N‐isopropylacrylamide) (PNIPAAm) polymeric hydrogel, consisting of either low (2300) or high (33,000) molecular weight linear PNIPAAm chains and the crosslinked PNIPAAm network. The properties of the resulting PNIPAAm hydrogels were characterized by DSC and SEM as well as their swelling ratios at various temperatures, the deswelling in hot water (48°C), and the oscillating shrinking–swelling properties within small temperature cycles. It was found that the deswelling rate of these semi‐IPN–like PNIPAAm hydrogels was improved if the molecular weight and/or composition of the linear PNIPAAm chains within the semi‐IPN–like PNIPAAm hydrogels were increased. This improved deswelling rate was attributed to the fast response nature of the linear PNIPAAm chains and the increased pore number in the matrix network, which provided numerous water channels for the water to diffuse out during the deswelling process at a temperature above the lower critical solution temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1935–1941, 2003     

Copolymers of acrylic acid with N‐vinylpyrrolidinone and 2‐hydroxyethyl methacrylate as pH‐responsive hydrogels synthesized through a photoinitiator‐free photopolymerization technique

pH‐sensitive hydrogels for biomedical applications were synthesized using a photoinitiator‐free technique involving the initiation of photopolymerization by donor/acceptor pairs. The differential photocalorimetric technique indicated a high polymerization rate for the N‐vinylpyrrolidinone (NVP, donor)/acrylic acid (AA, acceptor) pair at a 1:1 molar ratio. However, photopolymerization of larger quantities of these monomers (1:1 molar ratio) produced a water‐soluble polymer. Nevertheless, an anionic hydrogel was successfully formed when a small quantity of 2‐hydroxyethyl methacrylate (HEMA) was included in the NVP/AA formulation. A mixture of HEMA and AA, although both are classified as acceptors, photopolymerized to produce a copolymer which functioned as an anionic hydrogel. The swelling and drug release of these hydrogels were investigated in acidic, neutral and basic pH environments. Their biocompatibility with HaCaT human epidermal keratinocyte cells was tested and a positive cell growth as evidenced by the 3‐[4,5‐dimethylthiazol‐2‐yl]‐2,5‐diphenyl tetrazolium bromide (MTT) cell proliferation assay indicated that these hydrogels have no toxic effect on HaCaT. Copyright © 2006 Society of Chemical Industry     

Tuning the Mechanical Properties of BIEE‐Crosslinked Semi‐Interpenetrating,Double‐Hydrophilic Hydrogels

Double‐hydrophilic, semi‐interpenetrating (semi‐IPN) hydrogels are synthesized by encapsulating hydrophilic polyvinylpyrrolidone (PVP) linear chains in structure‐defined 1,2‐bis‐(2‐iodoethoxy)ethane (BIEE)‐crosslinked (poly(2‐(dimethylamino)ethyl methacrylate) (pDMAEMA) hydrogels. A series of semi‐IPN double‐hydrophilic hydrogels are prepared in which the pDMAEMA/BIEE content is kept the same and only the PVP content is varied, from 0 up to 33 wt%. The mechanical properties of the water‐swollen hydrogels are experimentally evaluated under unconfined compressive loading conditions, while a nonlinear hyperelastic constitutive equation is used to predict their mechanical response. No significant difference is found in the mechanical response of the semi‐IPN PVP/pDMAEMA/BIEE hydrogel containing 5 wt% PVP compared to the pDMAEMA/BIEE analog, however, for greater loading percentages (15 and 33 wt% of PVP), the semi‐IPN hydrogels exhibit less stiffness/higher ductility. Furthermore, in vitro biocompatibility studies are carried out for the pDMAEMA/BIEE and the semi‐IPN PVP/pDMAEMA/BIEE, indicating that both the formulations exhibit no toxicity in cultured cells.     

Separation of Toluene-Methanol Mixtures by Pervaporation Using Semi-IPN Polymer Membranes

Polyvinyl alcohol (PVOH) has been chemically modified by polymerizing hydroxyethylmethacrylate (HEMA) in aqueous solution of PVOH and finally crosslinking PVOH with glutaraldehyde to produce a semi-interpenetrating network (SIPN) membrane. Accordingly, three such SIPN membranes, namely SIPNI, SIPNII, and SIPNIII were synthesized with different weight ratio of PVOH: HEMA i.e., 1:0.25 (SIPNI), 1:0.50 (SIPNII), and 1:0.75 (SIPNIII). These SIPN membranes were used for pervaporative separation of methanol from its mixtures with toluene. The flux and methanol selectivity of these SIPN membranes were found to be much higher than conventional PVOH membrane crosslinked with glutaraldehyde. Among the three membranes, SIPNIII with 75 wt% HEMA incorporation shows optimum performance in terms of flux and methanol selectivity. The permeability of the membranes was also found to increase with increase in HEMA content in PVOH matrix. The novelty of the work lies in synthesis and characterization of a new kind of membrane and its potential for selective removal of methanol from its mixtures with toluene.     

Preparation and antidehydration of interpenetrating polymer network hydrogels based on 2‐hydroxyethyl methacrylate and N‐vinyl‐2‐pyrrolidone

This work reports the preparation of 2‐hydroxyethyl methacrylate (HEMA)/N‐vinyl‐2‐pyrrolidone (NVP) interpenetrating polymer network (IPN) hydrogels by UV‐initiated polymerization in the presence of free radical photoinitiator Darocur 1173 and cationic photoinitiator 4,4′‐dimethyl diphenyl iodonium hexafluorophosphate. The polymerization mechanism was investigated by the formation of gel network. The structure and morphology of the HEMA/NVP IPN hydrogels were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The results showed that the IPN gels exhibited homogeneous morphology. The dehydration rates of HEMA/NVP IPN hydrogels were examined by the gravimetric method. The results revealed that the hydrogels had a significant improvement of antidehydration ability in comparison with poly(2‐hydroxyethyl methacrylate)(PHEMA) hydrogel embedded physically with poly(N‐vinyl‐2‐pyrrolidone)(PVP). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical and dynamic mechanical studies of resol/vinyl acetate‐2‐ethylhexylacrylate/ hexamethoxymethylmelamine interpenetrating network systems

Resol was solution blended with vinyl acetate–2‐ethylhexylacrylate (VAc–EHA) resin in aqueous medium, in varying weight fractions, with hexamethoxymethylmelamine (HMMM) as crosslinker, and data was compared with a control. The present work was aimed at getting an optimum combination of tensile strength, dynamic mechanical strength, impact strength, and toughness by synthesis of an interpenetrating network (IPN) of the resins. The control gave a semi‐IPN system, in which the resol crosslinked, while the acrylic did not, whereas the blend, where HMMM was the crosslinker, gave a full IPN system. Full IPNs of the resol/VAc–EHA system had higher moduli and ultimate tensile strength than the semi‐IPNs. Dynamic mechanical study showed that full IPN systems have higher T_g values than semi‐IPN systems. The impact strength increases with increasing proportions of VAc–EHA copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1765–1771, 2003     

Characterization of hydrogels based on chitosan and copolymer of poly(dimethylsiloxane) and poly(vinyl alcohol)

Copolymers composed of poly(vinyl alcohol) (PVA) and poly(dimethylsiloxane) (PDMS) were crosslinked with chitosan to prepare semi‐interpenetrating polymer network (IPN) hydrogels by an ultraviolet (UV) irradiation method for application as potential biomedical materials. PVA/PDMS copolymer and chitosan was cast to prepare hydrogel films, followed by a subsequent crosslinking with 2,2‐dimethoxy‐2‐phenylacetophenone as a nontoxic photoinitiator by UV irradiation. Various semi‐interpenetrating polymer networks (semi‐IPNs) were prepared from different weight ratios of chitosan and the copolymer of PVA/PDMS. Photocrosslinked hydrogels exhibited an equilibrium water content (EWC) in the range of 65–95%. Swelling behaviors of these hydrogels were studied by immersion of the gels in various buffer solutions. Particularly, the PCN13 as the highest chitosan weight ratio in semi‐IPN hydrogels showed the highest EWC in time‐dependent and pH‐dependent swelling. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2591–2596, 2002     

Synthesis and characteristics of an amphoteric semi‐IPN hydrogel composed of acrylic acid and poly(diallydimethylammonium chloride)

Semi‐interpenetrating polymer network (IPN) hydrogels, with acrylic acid (AA) and poly(diallydimethylammonium chloride) (PDMDAAC), were constructed by a sequential IPN method. The characterizations of the IPN hydrogels were investigated by FTIR, DTA, and swelling tests under various conditions. The prepared semi‐IPN hydrogels exhibited relatively high swelling capacity, in the range of 477–630 g/g at 25°C. The results show that the swelling capacity of AA/PDMDAAC semi‐IPN hydrogels was pH and temperature dependent. Swelling behaviors were also studied in the different salt solutions. Swelling kinetic parameters are given. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 345–350, 2007     

Syntheses,characterization, and antibacterial activity of chitosan grafted hydrogels and associated mica‐containing nanocomposite hydrogels

Chitosan (CS) grafted poly[(acrylic acid)‐co‐(2‐hydroxyethyl methacrylate)] (CS‐g‐poly(AA‐co‐HEMA)) at different molar ratios of AA and HEMA, and the associated nanocomposite hydrogels of CS‐g‐poly(AA‐co‐HEMA)/mica were synthesized by radical copolymerization. The grafting positions at the amino or hydroxyl groups in the CS were identified by Fourier transform infrared spectroscopy. CS‐g‐poly(AA‐co‐HEMA) hydrogels were intercalated in the mica and the amount of hydrogel insertion did not affect the spacing of the silicate layers in mica. The higher mica loadings produced a rougher surface of the nanocomposite hydrogel. The water absorbency of the CS‐g‐poly(AA‐co‐HEMA)/mica nanocomposite hydrogels decreased with increasing levels of mica loading to a lower level than those of the CS‐g‐poly(AA‐co‐HEMA) hydrogels. Both CS‐g‐poly(AA) and CS‐g‐poly(AA‐co‐HEMA)/mica nanocomposite hydrogels exhibited a higher antiproliferative activity against Staphylococcus aureus than did the neat CS hydrogel with CS‐g‐poly(AA) revealing a very pronounced minimum inhibition concentration (MIC) of 1.56 mg mL^?1. The extent of mica loading in the CS‐g‐poly(AA‐co‐HEMA) nanocomposite hydrogels did not affect the MIC (12.5 mg mL^?1). © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of thermosensitive poly(N‐isopropylacrylamide)/poly(ethylene oxide) semi‐interpenetrating polymer networks

Temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels were successfully synthesized by using poly(ethylene oxide) as the interpenetrating agent. The newly prepared semi‐interpenetrating polymer network (semi‐IPN) hydrogels exhibited much better properties as temperature‐sensitive polymers than they did in the past. Characterizations of the IPN hydrogels were investigated using a swelling experiment, FTIR spectroscopy, and differential scanning calorimetry (DSC). Semi‐IPN hydrogels exhibited a relatively high temperature dependent swelling ratio in the range of 23–28 at room temperature. DSC was used for the determination of the lower critical solution temperature of the semi‐IPN hydrogel. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3032–3036, 2003