Effect of temperature and elongation on the liquid diffusion and permeation characteristics of natural rubber,nitrile rubber,and bromobutyl rubber

The diffusive properties of acetone, dichloromethane, and toluene in natural, nitrile, and bromobutyl rubber membranes at temperatures between 273 and 313 K and uniaxial elongations between 0 and 40% were investigated. As the temperature and elongation increase, the steady state flux increases, and the breakthrough time decreases. An increase in temperature leads to an increase in permeability, and small extensions do not cause significant changes in the diffusive properties. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1250–1255, 2000     

Characterization and transport properties of ceramic filler incorporated natural rubber composites

Crystalline glass–ceramic fillers were prepared from calcium carbonate, silica, alumina, and calcium fluoride by heating and subsequent quenching in cold water. The fillers were incorporated into natural rubber (1,4-cis-polyisoprene) and the filled rubber composites were crosslinked with sulfur in the presence of different rubber additives. The unfilled and filled rubber composites were characterized. The transport properties of benzene, toluene, and p-xylene (BTX) through the rubber composites were studied in terms of sorption, diffusion, permeation, and mass transfer coefficients. The effect of the ceramic fillers on the mechanical, thermal and transport properties were studied. The sorption data at different temperatures were used for calculating activation energy of diffusion, permeation, free energy, and enthalpy of sorption. The BTX remained in the liquid state within the composite matrix as evident from negative ΔS. The diffusion coefficient (D) and mass transfer coefficient (k_mtc) of BTX decreased with the increase in filler loading. Accordingly, for the transport of BTX the unfilled rubber showed a D (D × 10⁷ cm²/s) and mass transfer coefficient (k_mtc × 10⁴ cm/s) of 5.67/3.97/2.96 and 7.71/7.08/7.04, respectively which decreased to 5.06/2.95/2.57 and 7.53/6.95/6.90, respectively for the composite containing 50 wt.% ceramic filler.     

Melt‐spun polylactic acid fibers: Effect of cellulose nanowhiskers on processing and properties

Bio‐based continuous fibers were processed from polylactic acid (PLA) and cellulose nanowhiskers (CNWs) by melt spinning. Melt compounding of master batches of PLA with 10 wt % CNWs and pure PLA was carried out using a twin‐screw extruder in which compounded pellets containing 1 and 3 wt % of CNWs were generated for subsequent melt spinning. The microscopy studies showed that the fiber diameters were in the range of 90‐95 µm, and an increased surface roughness and aggregations in the fibers containing CNWs could be detected. The addition of the CNWs restricted the drawability of the fibers to a factor of 2 and did not affect the fiber stiffness or strength, but resulted in a significantly lower strain and slightly increased crystallinity. Furthermore, CNWs increased the thermal stability, creep resistance and reduction in thermal shrinkage of PLA fibers, possibly indicating a restriction of the polymer chain mobility due to the nanoscale additives. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Surface modification of nanocrystalline cellulose and its application in natural rubber composites

As a biopolymer with high mechanical strength, nanocellulose was generally considered as a green filler for reinforcing polymer. In this study, nanocrystalline cellulose (NCC) isolated from softwood pulp was successfully modified by cetyltrimethyl ammonium bromide (CTMAB), a cationic surfactant, and the modified nanocrystalline cellulose (m-NCC) was used to reinforce natural rubber (NR). In this composite architecture, it was found that when the filler content was 5 or 10 phr, the surface modification of NCC improved the dispersion state of NCC in NR matrix and the interfacial interaction between NR and NCC. Therefore, the NR/m-NCC composites exhibited outstanding mechanical properties, and its tensile strength, elongation at break and tear strength was increased by 132.8, 20, and 66.1%, respectively, compared to pristine NR composites. Besides, the modified NCC could accelerate the vulcanization and improve wet-skid resistance and aging resistance of NR composites. It is envisioned that the modified NCC has the potential to be generalized to manufacturing other polymer matrix composites strengthened with nanocellulose.     

Experimental Studies and Modelling of Sorption and Diffusion of Water and Alcohols in Cellulose Acetate

The sorption characteristics of water, methanol and ethanol vapours in cellulose acetate (CA) films were measured by microgravimetry. The sorption isotherms for water vapours in the CA film at different temperatures in the range 20–40°C do not obey the Flory equation over the whole water activity range. At high water activities, the sorption extent increases much faster with the water activity than it should according to the Flory approach. The isotherms over the whole water activity range can be fitted well by the ENSIC model, a new mechanistic model developed to account for the possibility of solvent cluster formation in the polymer material. Similar behaviour was observed for ethanol, which shows a lower tendency to form clusters, but higher affinity to CA. The sigmoidal shape found for the methanol sorption isotherm suggests a strong sorption on CA sites at low methanol activities. The Guggenheim–Anderson–De Boer equa-tion fitted well this isotherm. The diffusion coefficient, which was calculated from Fickian sorption kinetics at different solvent activities by curve fitting, was constant for water but increased with ethanol content in the membrane according to an exponential relationship characterized by a limit diffusion coefficient and a plasticization coefficient. The limit diffusion coefficient for water was two orders of magnitude larger than that for ethanol, but the activation energy for ethanol was twice as large. Methanol diffusion was only Fickian at a low solvent activity; the diffusion coefficient was one order of magnitude lower than that for water. © of SCI.     

Graft copolymers of microcrystalline cellulose as reinforcing agent for elastomers based on natural rubber

In the present study, free radical graft copolymerization of acrylic monomers and microcrystalline cellulose (MCC) was applied to develop a biopolymer for natural rubber reinforcements. The copolymerization was carried out in aqueous media. Cerium ammonium nitrate was employed as the initiator in the presence of nitric acid. Acrylic monomers used in the copolymer synthesis were ethyl acrylate (EA) and butyl acrylate (BA). Effects of monomer concentration, initiator concentration, polymerization time, and polymerization temperature on the obtained graft copolymers were investigated. The graft parameters were obtained by thermal gravimetric analysis method. The obtained copolymers (MCC‐g‐PEA, MCC‐g‐PBA) were characterized by attenuated total reflection, wide‐angle X‐ray diffraction, field‐emission electron microscopy, and thermal gravimetric analysis. In comparison to native MCC, better thermal stability of graft copolymers were observed. In addition, the graft copolymers reinforced natural rubber composites were produced, and sulfur was used as the vulcanizing agent. Their vulcanization and mechanical properties were characterized. Comparing to the native MCC reinforced natural rubber composites, the copolymers reinforced natural rubber composites shows improved mechanical properties, indicating the copolymer's potential application as rubber reinforcements. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43087.     

Development and molecular dynamics simulation of green natural rubber composites with modified sisal microcrystalline cellulose

In this study, green composites were prepared using natural rubber (NR) as the matrix and the sisal microcrystalline cellulose (MCC) as the filler. Three modifying agents oleic acid (OA), γ-aminopropyltriethoxylsilane (KH550), and bis-γ-(triethoxysilylpropyl)-tetrasulfide (Si69) were individually tested to modify the MCC to improve the interfacial compatibility of the NR and MCC. Combined with modern instrumental analysis technology and molecular dynamics simulation, the reinforcing effect and microscopic mechanism of modified MCC on NR were analyzed. The structure–activity relationship of NR and MCC composites was further revealed, and the interaction between the two components was clarified. At the same time, the reinforcing and compatibilizing effect of three kinds of modified MCC in NR matrix were also revealed. The results showed that the properties of NR/Mod-MCC composites were better than those of NR/MCC composites, where NR/OA-MCC presented the highest tensile strength, followed by NR/Si69-MCC. In addition, NR/Si69-MCC exhibited higher elongation at break and NR/KH550-MCC exhibited higher vulcanization characteristics. Molecular model systems were constructed through molecular dynamics simulation to investigate the interactions between the three modified cellulose molecules and the NR molecules. OA-cellulose has a better interaction with NR than KH550-cellulose and Si69-cellulose, The simulation results were consistent with the experimental results.     

Experimental and simulation studies on molecular transport of substituted monocyclic aromatic liquids into fluoropolymer sheet membranes: Liquid structure–diffusion, –sorption,and –permeation relationships

The present study reports an investigation on the molecular transport of 10 monocyclic aromatic liquids (benzene, chlorobenzene, 1,2‐dichlorobenzene, bromobenzene, toluene, p‐xylene, trimethylbenzene, ethylbenzene, methoxybenzene, and ethoxybenzene) at 40 and 50°C through sheet polymeric membranes (FLS‐2650) using a sorption gravimetric technique. Diffusion and permeation coefficients of these liquids were calculated from the sorption data using Fick's diffusion equation. Sorption results were analyzed typically in the case of benzene and chlorobenzene to compute the concentration profiles at different depths along the thickness direction of the sheet membranes and at different time intervals by solving the Fick's equation under appropriate boundary conditions, based on the numerical simulation method developed in “C” language using a finite‐difference method. Transport results were analyzed to establish the relationships between the penetrating liquid structures with diffusion, permeation, and sorption data. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 991–996, 2004     

Liquid crystal behavior of cellulose nanoparticles-ethyl cellulose composites: Preparation,characterization, and rheology

This work deals with assessing the approach for preparation of cellulose nanoparticles (CNPs) to be acted as synergistic component in liquid crystal (LC) ethyl cellulose composite (EC-CNPs). In this respect different structures of CNPs were prepared by acid and salt agents. These prepared CNPs were characterized by carboxyl content, IR, transmission electron microscope (TEM), and zeta potential, while their composites with EC were characterized by rheological measurements as a key factor for measuring the critical concentration of LC behavior. The results showed that, the crystallinity of CNPs obtained by ammonium persulfate exceeded that prepared by sulfuric acid hydrolysis. TEM images of stained CNPs showed both methods led to produce nanoparticles have rod like shape with aspect ratio (L/W) between 7.69 ± 3 and 31.3 ± 5. For the rheological measurements, it demonstrated the efficient of incorporating the CNPs to EC (EC-CNPs composites) to decrease the critical concentration of EC from 40 wt% to approximately 34 wt%.     

Evaluation of kinetics and transport mechanism of solvents through natural rubber composites containing organically modified gadolinium oxide

The solvent transport properties of the prepared composites were analysed using solvents of varying cohesive energy density and the effect of both modified as well as unmodified filler on the sorption and diffusion behaviour of NR vulcanisates has been investigated. It is found that the equilibrium uptake decreases with increase in filler content, as anticipated owing to the restrictions offered by the filler for solvents to diffuse into the polymer matrix. The mechanism of transport in natural rubber composites was carefully tracked and it was found to exhibit an anomalous mode of solvent transport where the polymer relaxation is in par with the rate of diffusion. Theoretical modelling of the swelling parameters was done and the results were found to be in agreement with existing models. The excellent swelling resistance coupled with the simultaneous improvement in mechanical properties would definitely pave way for the utilisation of these composites as barrier membranes.     

Castor oil‐based polyurethane–polyester nonwoven fabric composites: Mechanical properties,chemical resistance,and water sorption behavior at different temperatures

Castor oil‐based polyurethane (PU)–polyester nonwoven fabric composites were fabricated by impregnating the polyester nonwoven fabric in a composition containing castor oil and diisocyanate. The effects of different diisocyanates such as toluene‐2,4‐diisocyanate (TDI) and hexamethylene diisocyanate (HMDI) on the mechanical properties have been studied for neat PU sheets and their composites with polyester nonwoven fabric. Chemical resistance of the PU composites has been assessed by exposing the specimens to different chemical environments. Percentage water absorption of composites and neat PU sheets has been determined both at room temperature and in boiling water. Both TDI‐ and HMDI‐based PU composites showed a marginal improvement in tensile strength retention at 100°C heat ageing. Water sorption studies were carried out at different temperatures, viz, 30, 50, and 70°C, based on immersion weight gain method. From the sorption results, the diffusion (D) and permeation (P) coefficients of water penetrant have been calculated. Attempts were made to estimate the empirical parameters such as n, which suggests the mode of transport (non‐Fickian), and K, a constant which depends on the structural characteristics of the polymer in addition to its interaction in boiling water. The temperature dependence of the transport coefficients has been used to estimate the activation energy parameters for diffusion (E_D) and permeation (E_p) processes from Arrhenius plots. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Diffusion and sorption of benzene vapor through polybutadiene‐, polybutadiene/styrene‐, and polybutadiene/acrylonitrile‐based polyurethanes

A series of polyurethane (PU) films made from toluene diisocyanate (TDI), 1,4‐butanediol (BDO), and hydroxyl‐terminated polybutadiene (HTPB), hydroxyl terminated polybutadiene/styrene (HTBS), or hydroxyl terminated polybutadiene/acrylonitrile (HTBN) was synthesized by solution polymerization. The absorption of benzene vapor was found mainly in the soft phase. The equilibrium adsorption (M_∞) was reduced with increasing hard segment content for all the PUs. The values of M_∞ were in the sequence of HTBN‐PUs > HTBS‐PUs > HTPB‐PUs, which could be explained by the different interaction parameters between soft segments and benzene. The HTBN‐PU film showed the lowest degree of phase segregation and had more hard segments intermixed in the soft phase, restricting the movement of soft segments, and therefore resulted to non‐Fickian behavior, while the HTPB‐PU is antithetical. FTIR and atomic force microscopy were utilized to identify the hydrogen bonding behavior and morphology change of the PU films before and after the absorption of benzene vapor. The tensile strength of the HTBN‐PUs showed a greater decrease than that of HTBS‐PUs and HTPB‐PUs after absorbing benzene vapor. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2984–2991, 2004     

Preparation,characterization, and applicability of novel calix[4]arene‐based cellulose acetate membranes in gas permeation

Cellulose acetate (CA) is well known glassy polymer used in the fabrication of gas‐separation membranes. In this study, 5,11,17,23‐tetrakis(N‐morpholinomethyl)‐25,26,27,28‐tetrahydroxycalix[4]arene (CL) was blended with CA to study the gas‐permeation behavior for CO₂, N₂, and CH₄ gases. We prepared the pure CA and CA/CL blended membranes by following a diffusion‐induced phase‐separation method. Three different concentrations of CL (3, 10, and 30 wt %) were selected for membrane preparation. The CA/CL blended membranes were then characterized via Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X‐ray diffraction analysis. The homogeneous blending of CL and CA was confirmed in the CA/CL blended membranes by both SEM and AFM analysis. In addition to this, the surface roughness of the CA/CL blended membranes also increased with increasing CL concentration. FTIR analysis described the structural modification in the CA polymer after it was blended with CL too. Furthermore, CL improved the tensile strength of the CA membrane appreciably from 0.160 to 1.28 MPa, but this trend was not linear with the increase in the CL concentration. CO₂, CH₄, and N₂ gases were used for gas‐permeation experiments at 4 bars. With the permeation experiments, we concluded that permeability of N₂ was higher in comparison to those of CO₂ and CH₄ through the CA/CL blended membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39985.     

Diffusion and sorption of organic liquids through polymer membranes. II. Neoprene,SBR, EPDM,NBR, and natural rubber versus n-alkanes

Diffusion and sorption of n-alkanes (C₆–C₁₀) through commercial polymer membranes such as neoprene, styrene butadiene rubber, ethylene propylene diene terpolymer, nitrile butadiene rubber, and natural rubber have been studied from 25 to 60°C. The diffusion results have been explained in terms of the size of liquid molecules and the diffusion mechanism was found to follow the Fickian trend. Nitrile butadiene rubber and neoprene showed much smaller values of diffusivities and sorption constants than the other polymer membranes. Arrhenius parameters for the activated diffusion process and the thermodynamic quantities for the process of equilibrium sorption have been estimated.     

Morphology and antibacterial properties of natural rubber composites based on biosynthesized nanosilver

The objective of this work is to improve the properties of natural rubber composites (NRC) that were frequently used in medical and health supplies, using nanosilver additions. Silver nanocolloids were biosynthesized with an aqueous medium of aloe leaf extract (ALE) as capping agent, and then were filled in natural rubber matrix to prepare nanosilver‐based NRC. UV–vis spectrophotometer, X‐ray diffraction, and transmission electron microscopic analyses proved that the particle size of resultant silver was about 20 nm. The antibacterial activities against Staphylococcus aureus and Escherichia coli bacteria of NRC were dependable on the silver nanoparticles content and the treating methods on ALE, which was used in synthesizing silver nanocolloids. The morphology and thermal stability effect of nanosilver on NRC were determined with scanning electron microscopic and thermogravimetric analysis, respectively. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40746.     

Determination of the diffusion coefficients of organic solvents in polyepichlorohydrin: A comparative study of inverse gas chromatography and sorption methods

The diffusivity of organic solvents in polyepichlorohydrin was studied with two different experimental setups: inverse gas chromatography (IGC) with packed columns and sorption measurements in gravimetric experiments monitored in a Cahn electrobalance. The aim of this work was to test the possibility of solving an inherent problem in the data reduction of IGC measurements, that is, the necessity of characterizing the morphology of the polymer coated on the support (usually given in the so‐called geometric factor of the column). Temperatures between 35 and 65°C were used in the IGC experiments, whereas the sorption measurements were performed between 30 and 40°C. Glass beads were used as supports in IGC for obtaining data concerning the variation of the plate height with the average gas velocity, with which the use of the Van Deemter equation allowed the determination of the diffusion coefficient if the geometric factor was known. In the sorption experiments, the diffusion coefficients at different penetrant activities were directly measured. For their extrapolation within the same concentration range used for IGC (infinite dilution of the penetrant), the theoretical model of Vrentas and Duda was used. By a combination of sorption and IGC experiments, the geometric factor of an IGC column could be adjusted, and this allowed the determination of the diffusion parameters of any other solvent in the same column. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2216–2223, 2003     

Cellulose microfibrils from potato tuber cells: Processing and characterization of starch–cellulose microfibril composites

The ultrastructure and morphology of potato (Solanum tuberosum L.) tuber cells were investigated by optical, scanning, and transmission electron microscopies. After removal of starch granules, pectins and hemicelluloses were solubilized under alkaline conditions. The alkaline insoluble residue consisted mainly of primary cell wall cellulose, which can be disintegrated under shearing to produce a homogenized microfibril suspension, as reported in a previous work. 40 Composite materials were processed from this potato cellulose microfibril suspension, gelatinized potato starch as a matrix and glycerol as a plasticizer. After blending and casting, films were obtained by water evaporation. The mechanical properties and water absorption behavior of the resulting films were investigated, and differences were observed depending on the glycerol, cellulose microfibrils, and relative humidity content. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 2080–2092, 2000     

氧化石墨烯/天然橡胶复合材料的制备与性能

采用己内酰胺（CPL）改性氧化石墨烯（GO）（CPL-GO）,与天然橡胶（NR）复合后通过熔融共混法制备了CPL-GO/NR复合材料。考察了CPL-GO用量对CPL-GO/NR复合材料物理机械性能、界面相互作用和气体阻隔性能的影响。结果表明,CPL改性GO后,X射线衍射层间距增加,片层堆砌更为松散,CPL-GO与水接触角增至91.2°。当CPL-GO的质量分数为2.0%时,CPL-GO/NR复合材料的拉伸强度为26.1 MPa,较纯NR提高了50.9%。随着CPL-GO用量的增加,复合材料的储能模量增加,损耗因子的峰值减小,表明GO经CPL表面改性后与NR复合,增强了两相界面间的相互作用,从而提高了复合材料抵抗变形的能力。在40 ℃下,当CPL-GO的质量分数为3.0%时,CPL-GO/NR复合材料的气体渗透系数较纯NR下降了57.1%。     

Nanocomposites of ethylene vinyl alcohol copolymer with thermally resistant cellulose nanowhiskers by melt compounding (I): Morphology and thermal properties

In this study, ethylene‐vinyl alcohol copolymer (EVOH) nanocomposites were prepared by melt compounding both plant cellulose nanowhiskers (CNW) and bacterial cellulose nanowhiskers (BCNW) as nanofillers. Electrospinning and a “dissolution precipitation” method were used as strategies for the incorporation of CNW in EVOH before melt compounding with the aim of enhancing the degree of dispersion of the nanocrystals when compared with direct melt‐mixing of the freeze‐dried product with the polymer. As revealed by morphological characterization, the proposed preincorporation methods led to a significant improvement in the dispersion of the nanofiller in the final nanocomposite films. Furthermore, it was possible to incorporate concentrations as high as 4 wt % BCNW without causing significant agglomeration of the nanofiller, whereas increasing the CNW concentration up to 3 wt % induced agglomeration. Finally, DSC studies indicated that the crystalline content was significantly reduced when the incorporation method led to a poor dispersion of the nanocrystals, whereas high‐nanofiller dispersion resulted in thermal properties similar to those of the neat EVOH. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Melt compounded nanocomposites with semi‐interpenetrated network structure based on natural rubber,polyethylene, and carrot nanofibers

The present study deals with the processing and characterization of cellulose nanocomposites natural rubber (NR), low‐density polyethylene (LDPE) reinforced with carrot nanofibers (CNF) with the semi‐interpenetrated network (S‐IPN) structure. The nanocomposites were compounded using a co‐rotating twin‐screw extruder where a master‐batch of NR and CNF was fed to the LDPE melt, and the NR phase was crosslinked with dicumyl peroxide. The prepared S‐IPN nanocomposites exhibited a significant improvement in tensile modulus and yield strength with 5 wt % CNF content. These improvements are due to a better phase dispersion in the S‐IPN nanocomposites compared with the normal blend materials, as demonstrated by optical microscopy, electron microscopy and ultraviolet–visible spectroscopy. The S‐IPN nanocomposite also displayed an improved crystallinity and higher thermal resistance compared with NR, CNF, and the normal blend materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45961.