The effect of soft‐segment structure on the properties of novel thermoplastic polyurethane elastomers based on an unconventional chain extender

Thermoplastic polyurethane elastomers (TPUs) are now widely used because of their excellent properties that include high tensile and tear strength, and good abrasion, impact and chemical resistance. TPUs are multiblock copolymers with alternating sequences of hard segments composed of diisocyanates and simple diols (chain extenders) and soft segments formed by polymer diols. Commonly used hard segments for TPUs are derived from 4,4′‐diphenylmethane diisocyanate (MDI) and aliphatic diols. The aim of our research was to examine the possibility of obtaining TPUs with good tensile properties and thermal stability by using an unconventional aliphatic‐aromatic chain extender, containing sulfide linkages. Three series of novel TPUs were synthesized by melt polymerization from poly(oxytetramethylene) diol, poly(ε‐caprolactone) diol or poly(hexane‐1,6‐diyl carbonate) diol of number‐average molecular weight of 2000 g mol^?1 as soft segments, MDI and 3,3′‐[methylenebis(1,4‐phenylenemethylenethio)]dipropan‐1‐ol as a chain extender. The structure and basic properties of the polymers were examined using Fourier transfer infrared spectroscopy, X‐ray diffraction, atomic force microscopy, differential scanning calorimetry, thermogravimetric analysis, Shore hardness and tensile tests. It is possible to synthesize TPUs from the aliphatic‐aromatic chain extender with good tensile properties (strength up to 42.6 MPa and elongation at break up to 750%) and thermal stability. Because the structure of the newly obtained TPUs incorporates sulfur atoms, the TPUs can exhibit improved antibacterial activity and adhesive properties. Copyright © 2011 Society of Chemical Industry     

Studies on thermoplastic polyurethanes based on new diphenylethane‐derivative diols. III. The effect of molecular weight and structure of soft segment on some properties of segmented polyurethanes

Two series of poly(ether urethane)s and one series of poly(ester urethane)s were synthesized, containing, respectively, poly(oxytetramethylene) diol (PTMO) of M _n = 1000 and 2000 and poly(ε‐caprolactone) diol of M _n = 2000 as soft segments. In each series the same hard segment, i.e., 4,4′‐(ethane‐1,2‐diyl)bis(benzenethiohexanol)/hexane‐1,6‐diyl diisocyanate, with different content (～ 14–72 wt %) was used. The polymers were prepared by a one‐step melt polymerization in the presence of dibutyltin dilaurate as a catalyst, at the molar ratio of NCO/OH = 1 (in the case of the polymers from PTMO of M _n = 1000 also at 1.05). For all polymers structures (by FTIR and X‐ray diffraction analysis) and physicochemical, thermal (by differential scanning calorimetry and thermogravimetric analysis), and tensile properties as well as Shore A/D hardness were determined. The resulting polymers were thermoplastic materials with partially crystalline structures (except the polymer with the highest content of PTMO of M _n = 2000). It was found that the poly(ether urethane)s showed lower crystallinity, glass‐transition temperature (T_g), and hardness as well as better thermal stability than the poly(ester urethane)s. Poly(ether urethane)s also exhibited higher tensile strength (up to 23.5 MPa vs. 20.3 MPa) and elongation at break (up to ～ 1950% vs. 1200%) in comparison with the corresponding poly(ester urethane)s. Among the poly(ether urethane)s an increase in soft‐segment length was accompanied by an increase in thermal stability, tensile strength, and elongation at break, as well as a decrease in T_g, crystallinity, and hardness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mixed macrodiol‐based siloxane polyurethanes: Effect of the comacrodiol structure on properties and morphology

Two series of polyurethanes were prepared to investigate the effect of comacrodiol structure on properties and morphology of polyurethanes based on the siloxane macrodiol, α,ω‐bis(6‐hydroxyethoxypropyl) polydimethylsiloxane (PDMS). All polyurethanes contained a 40 wt % hard segment derived from 4,4′‐methylenediphenyl diisocyanate (MDI) and 1,4‐butanediol (BDO), and were prepared by a two‐step, uncatalyzed bulk polymerization. The soft segments were based on an 80/20 mixture of PDMS (MW 967) and a comacrodiol (MW 700), selected from a series of polyethers and polycarbonates. The polyether series included poly(ethylene oxide) (PEO), poly(propylene oxide) (PPO), poly(tetramethylene oxide) (PTMO), poly(hexamethylene oxide), and poly(decamethylene oxide) (PDMO), whereas the polycarbonate series included poly (hexamethylene carbonate) diol (PHCD), poly [bis(4‐hydroxybutyl)‐tetramethyldisiloxy carbonate] diol (PSCD), and poly [hexamethylene‐co‐bis(4‐hydroxybutyl)‐tetramethyldisiloxy carbonate] diol (COPD). Polyurethanes were characterized by size exclusion chromatography, tensile testing, differential scanning calorimetry (DSC), and dynamic mechanical thermal analysis (DMTA). The results clearly demonstrated that the structure of the comacrodiol influenced the properties and morphology of siloxane‐based polyurethanes. All comacrodiols, except PEO, improved the UTS of the polyurethane; PHMO and PTMO were the best polyether comacrodiols, while PSCD was the best polycarbonate comacrodiol. Incorporation of the comacrodiol made polyurethanes more elastomeric with low modulus, but the effect was less significant with polycarbonate comacrodiols. DSC and DMTA results strongly supported that the major morphological change associated with incorporation of a comacrodiol was the significant increase in the interfacial regions, largely through the compatibilization with the hard segment. The extent of compatibilization varied with the comacrodiol structure; hydrophilic polyethers such as PEO were the most compatible, and consequently, had poor mechanical strength. Among the polyethers, PHMO was the best, having an appropriate level of compatibility with the hard segment for substantial improvement in mechanical properties. Siloxy carbonate comacrodiol PSCD was the best among the polycarbonates. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1071–1082, 2000     

Effects of wide‐range γ‐irradiation doses on the structures and properties of 4,4′‐dicyclohexyl methane diisocyanate based poly(carbonate urethane)s

For medical applications, 4,4′‐dicyclohexyl methane diisocyanate (HMDI)‐based poly(carbonate urethane)s were synthesized from HMDI and 1,4‐butanediol as hard segments and poly(carbonate diol) (number‐average molecular weight = 2000 g/mol) as soft segments. The effects of wide‐range γ irradiation on the samples were examined through a series of analytical techniques. Scanning electron microscopy revealed that γ irradiation etched and roughened the surfaces of the irradiated samples. The gel content and crosslinking density measurements confirmed that crosslinking occurred along with degradation at all of the investigated irradiation doses and the degree of both crosslinking and degradation increased with increasing irradiation dose. Fourier transform infrared spectroscopy demonstrated that chain scission in the γ‐irradiated samples occurred at the carbonate and urethane bonds. The decreasing molecular weight and tensile strength indicated that the degradation increased with the γ‐irradiation dose. Differential scanning calorimetry and dynamic mechanical thermal analysis indicated that γ irradiation had no significant effect on the phase‐separation structures. There was a slight reduction in the contact angle. An evaluation of the cytotoxicity demonstrated the nontoxicity of the nonirradiated and irradiated polyurethanes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41049.     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Synthesis and surface mobility of segmented polyurethanes with fluorinated side chains attached to hard blocks

Novel polyurethanes with fluorinated side chains attached to hard blocks were synthesized and characterized by NMR, mass spectroscopy, DSC and gel permeation chromatography (GPC). A unique chain extender, 3-(2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-pentadecafluoro-octyloxy)-propane-1,2-diol (PFOPDOL) was prepared from 3-(2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-pentadecafluoro-octyloxymethyl)-oxirane (PDFOMO) by reacting it with diluted perchloric acid. Poly(ether urethane)s and poly(carbonate urethane)s containing various amounts of the chain extender with fluorinated side chains were then synthesized using methylenebis(phenylene isocyanate) (MDI), polytetramethyleneoxide (PTMO), poly(1,6-hexyl-1,5-pentylcarbonate) diol (PHPCD), 1,4-butandiol (BDO) and PFOPDOL. Mechanical properties of the polyurethanes were characterized by Instron. Surface properties were characterized by X-ray photoelectron spectroscopy (XPS) and contact angle measurements. Results from GPC and Instron studies indicated that fluorinated polyurethanes with high molecular weights and good mechanical properties were obtained. Results from XPS and contact angle studies indicated that the surface of fluorinated polyurethanes were very nonpolar due to migration of fluorinated side chains to the surface.     

The effect of the soft segment of prepolymers on properties of poly(urethane‐ester) and its biodegradability

The influence of soft‐segment prepolymers prepared through the polymerization of δ‐valerolactone (VL) and 2,2‐dimethyl‐1,3‐propandiol (DP) monomers on the structure and properties of poly(urethane‐ester) as well as its biodegradability were investigated. Poly(urethane‐ester) was prepared in two steps. The first step was the preparation of prepolymers with various chain lengths by polymerizing VL and DP monomers in the presence of a distannoxane catalyst at 100 °C under nitrogen atmosphere. The second step was the preparation of poly(urethane‐ester) by polymerizing 4,4′‐methylene‐bis(phenyl isocyanate) (MDI) and prepolymers with various chain lengths in the absence of catalysts. The poly(urethane‐ester) was characterized through an analysis of functional groups (FTIR), thermal properties (differential thermal analysis/TGA), mechanical properties (tensile tester), crystallinity (XRD) and biodegradability. An increased chain length of the prepolymer used in polymerization with MDI leads to an increase in the thermal properties and crystallinity of poly(urethane‐ester). However, the maximum biodegradability in the activated sludge was observed in the poly(urethane‐ester) prepared by polymerizing MDI and prepolymers with a molar VL/DP ratio of 20/1. The amorphous parts of polymers were more easily decomposed by microorganism enzymes than were the crystalline parts after an incubation period of 30 days. Copyright © 2011 Society of Chemical Industry     

Segmented poly(urethane‐urea) elastomers based on polycaprolactone: Structure and properties

A series of segmented poly(urethane‐urea) polymers have been synthesized varying the hard segments content, based on the combination of polycaprolactone diol and aliphatic diisocyanate (Bis(4‐isocyanatocyclohexyl)methane), using diamine (1,4‐Butylenediamine) as the chain extender. The microstructure and properties of the material highly depend on the hard segments content (from 14 to 40%). These PUUs with hard segment content above 23% have elastomeric behaviors that allow high recoverable deformation. The chemical structure and hydrogen bonding interactions were studied using FTIR and atomic force microscopy, which revealed phase separation that was also confirmed by DSC, dynamic‐mechanical, and dielectric spectroscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyimides derived from 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene

A novel diamine, 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4‐bis [3‐oxy‐(N‐phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, ¹H NMR, and elemental analysis. A series of five‐member ring, hydrazine‐based polyimides were prepared from this diamine and various aromatic dianhydrides via one‐step polycondensation in p‐chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17–0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight‐loss temperatures of the polyimides were near 450°C in air and 500°C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass‐transition temperatures (T_gs) of these polymers were in the range of 265–360°C. The wide‐angle X‐ray diffraction showed that all the polyimides were amorphous. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of novel polyurethanes containing 4,4′‐{oxy‐1,4‐diphenyl bis(nitromethylidine)}diphenol schiff base diol

Four novel segmented polyurethanes (PUs) based on4,4′‐{oxy‐1,4‐diphenyl bis(nitromethylidine)}diphenol (ODBNMD) diol with different diisocyanates such as 4,4′‐diphenylmethane diisocyanate, toluene 2,4‐diisocyanate, isophorone diisocyanate, and hexamethylene diisocyanate have been prepared by solution method. The structures of ODBNMD and PUs have been confirmed by Fourier transform infrared (FTIR), nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), UV‐visible, and fluorescence spectroscopies. The segmented PUs were further characterized by thermogravimetry (TGA), differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction. FTIR confirmed hydrogen bonding interactions, whereas TGA and DSC suggested that introduction of aromatic/phenyl ring in the main chain considerably increased the thermal stability. POLYM. ENG. SCI., 54:24–32, 2014. © 2013 Society of Plastics Engineers     

Synthesis,characterization, and acoustic properties of new soluble polyurethanes based on 2,2′‐[1,4‐phenylenebis(nitrilomethylylidene)diphenol and 2,2′‐[4,4′‐methylene‐di‐2‐methylphenylene‐1,1′‐bis(nitrilomethylylidene)]diphenol

Eight novel polyurethanes based on 2,2′‐[1,4‐phenylenebis(nitrilomethylylidene)]diphenol and 2,2′‐[4,4′‐methylene‐di‐2‐methylphenylene‐1,1′‐bis(nitrilomethylylidene)]diphenol acting as hard segments with two aromatic and two aliphatic diisocyanates (4,4′‐diphenylmethane diisocyanate, toluene 2,4‐diisocyanate, isophorone diisocyanate, and hexamethylene diisocyanate) were prepared and characterized with Fourier transform infrared, UV spectrophotometry, fluorescence spectroscopy, ¹H‐NMR and ¹³C‐NMR spectroscopy, thermogravimetric analysis, and differential thermal analysis. All the polyurethanes contained domains of semicrystalline and amorphous structures, as indicated by X‐ray diffraction. The acoustic properties and solubility parameters were calculated with the group contribution method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Siloxane‐based segmented poly(urethane‐urea) elastomer: Synthesis and characterization

A series of segmented poly(urethane‐urea) block copolymers were synthesized with varying proportions of polydimethylsiloxane diols in combination with polytetramethylene ether glycol (PTMG) using 4,4'‐methylenediphenyl diisocyanate followed by chain extension with a (50:50 mol %) mixture of 4,4'‐methylene‐bis(3‐chloro‐2,6‐diethylaniline) (M‐CDEA) and 1,4‐butanediol (BD). The molecular structures of polydimethylsiloxane urethane‐ureas were characterized by ATR‐FTIR and ¹H‐NMR spectroscopic techniques. Distribution of siloxane domain and its influence on surface roughness were investigated by scanning electron microscopy (SEM) and atomic forced microscopy (AFM), respectively. The mechanical and thermal properties of the elastomers were studied by thermogravimetric analysis, dynamical mechanical thermal analysis, and tensile measurement. The results showed that by incorporation of polydimethylsiloxane diol and M‐CDEA chain extender in polyurethane formulation, some improvements in thermal stability, fire resistance and surface hydrophilicity were achieved. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1743–1751, 2013     

Monitoring of chemical reactions during polymer synthesis by real‐time attenuated total reflection (ATR)–FTIR spectroscopy

The present study demonstrates in situ real‐time attenuated total reflection (ATR)–FTIR spectroscopy as a powerful tool for monitoring and analyzing different polymerization and polymer modification reactions. Thus, a metallocene catalyzed copolymerization of propene and 10‐undecene‐1‐ol, a polycondensation reaction towards polysulfone, and a modification reaction of OH end groups of hyperbranched poly(urea‐urethane) were investigated successfully. The interpretation of the development of FTIR spectra was carried out on the basis of typical vibration bands of chemical groups of the corresponding monomers and polymers in each case, e.g. of the C?C double bond of 10‐undecene‐1‐ol during the copolymerization, the new C? O? C group of polysulfone, and the new urethane end group of poly(urea‐urethane). Kinetics prediction is also under consideration. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1374–1380, 2006     

Solid‐phase preparation method of silica‐supported 2,2′‐methylenebis(6‐tert‐butyl‐4‐methyl‐phenol) and its antioxidative behavior in styrene‐butadiene rubber

A solid‐phase preparation method is applied to the synthesis of a novel supported rubber antioxidant, silica–supported 2,2′‐methylenebis(6‐tert‐butyl‐4‐methyl‐phenol) (SiO₂‐2246), by directly reacting 2,2′‐methylenebis (6‐tert‐butyl‐4‐methyl‐phenol)(antioxidant 2246) with silica. FTIR, Raman spectroscopy and TGA confirm that the antioxidant 2246 is chemically bonded on the surface of the silica particles. The SEM observation shows that the SiO₂‐2246 is homogeneously dispersed in the styrene‐butadiene rubber (SBR) matrix. The results of the apparent activation energy and the attenuated total reflectance infrared spectrometry indicate that the antioxidative efficiency of the SiO₂‐2246 in SBR is superior to the corresponding low‐molecular‐weight 2246. The thermal oxidative stability of the SBR/SiO₂‐2246 composites is much higher than that of the SBR/SiO₂/2246 composites by comparing their mechanical properties retentions and crosslinking densities. Additionally, the advantages of SiO₂‐2246 also include low migration, low volatility, and low pollution. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43014.     

Synthesis and characterization of new functional poly(urethane‐imide) crosslinked networks

To synthesize new functional poly(urethane‐imide) crosslinked networks, soluble polyimide from 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride, 4,4′‐oxydianiline, and maleic anhydride and polyurethane prepolymer from polycaprolactone diol, tolylene 2,4‐diisocyanate and hydroxyl ethyl acrylate were prepared. Poly(urethane‐imide) thin films were finally prepared by the reaction between maleimide end‐capped soluble polyimide (PI) and acrylate end‐capped polyurethane (PU). The effect of polyurethane content on dielectric constant, residual stress, morphology, thermal property, and mechanical property was studied by FTIR, prism coupler, Thin Film Stress Analyzer (TFSA), XRD, TGA, DMTA, and Nano‐indentation. Dielectric constant of poly(urethane‐imide) thin films (2.39–2.45) was lower than that of pure polyimide (2.46). Especially, poly(urethane‐imide) thin films with 50% of PU showed lower dielectric constant than other poly(urethane‐imide) thin films did. Lower residual stress and slope in cooling curve were achieved in higher PU content. Compared to typical polyurethane, poly(urethane‐imide) thin films exhibited better thermal stability due to the presence of the imide groups. The glass transition temperature, modulus, and hardness decreased with increase in the flexible PU content even though elongation and thermal expansion coefficient increased. Finally, poly(urethane‐imide) thin films with low residual stress and dielectric constant, which are strongly affected by the morphological structure, chain mobility, and modulus, can be suggested to apply for electronic devices by variation of PU. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 113–123, 2006     

Effects of co‐hard segments on the microstructure and properties thermoplastic poly(ether ester) elastomers

A thermoplastic poly(ether ester) elastomer (TPEE) is composed of polyester hard segments and polyether soft segments. Polyester and polyether segments are often homopolymer segments. This work aims at incorporating poly(butylene phthalate (PBP) as co‐hard segments in the hard segments of poly(butylene terephthalate) (PBT)‐b‐poly(tetramethylene oxide) (PTMO) thermoplastic elastomer, and investigating structures and properties of the resulting materials, denoted as (PBT‐co‐PBP)‐b‐PTMO. (PBT‐co‐PBP)‐b‐PTMO was synthesized from dimethyl terephthalate (DMT), dimethyl phthalate (DMP), PTMO (M_n = 1000 g/mol), and 1,4‐butanediol (BDO). The crystallinity of (PBT‐co‐PBP)‐b‐PTMO first decreased and then increased with increasing PBP content from 5% to 10% due to a decrease in the average sequence length of the PBT hard segments. Its elongation at break was increased by 200–350%. When the mass fractions of PBT and PBP were 42% and 8%, respectively, the (PBT‐co‐PBP)‐b‐PTMO showed the best performance in terms of permanent deformation, strength, and hardness whose values were 30%, 25 MPa, and 37 D, respectively. All the synthesized copolymers had good thermal stability with a decomposition temperature of 400°C or so. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43337.     

Synthesis and characterization of novel optically active poly(imide–urethane)s derived from N,N′‐(pyromellitoyl)‐bis‐(L‐leucine) diisocyanate and aromatic diols

N,N′‐(Pyromellitoyl)‐bis‐(L ‐leucine) diacid was reacted with ethyl chloroformate in the presence of triethylamine followed by reaction with activated sodium azide and gave N,N′‐(pyromellitoyl)‐bis‐(L ‐leucine) diacylazide in high yield. This diacylazide was heated in dry benzene and gave the unstable N,N′‐(pyromellitoyl)‐bis‐(L ‐leucine) diisocyanate ( 5 ) in quantitative yield. Thus, diisocyanate 5 was generated in situ and polycondensation reaction of this monomer with several aromatic diols, such as 4,4′‐dihydroxybiphenyl, 1,4‐hydroquinone, bisphenol A, phenolphthalein and 1,4‐dihydroxyanthraquinone, was performed in dry toluene under refluxing in the presence of 1,4‐diazabicyclo[2.2.2]octane (triethylenediamine) as a catalyst. The polymerization reactions proceeded within 48 h, producing a series of optically active poly(imide–urethane)s with good yield and moderate inherent viscosity in the range 0.18–0.28 dl g^?1. All of the above polymers were fully characterized by infrared spectra, elemental analyses and specific rotation. Some structural characterization and physical properties of these optically active poly(imide–urethane)s are reported Copyright © 2003 Society of Chemical Industry     

Synthesis and characterization of organosoluble and transparent polyimides derived from trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride

A novel dianhydride, trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride (1,2‐CHDPA), was prepared through aromatic nucleophilic substitution reaction of 4‐nitrophthalonitrile with trans‐cyclohexane‐1,2‐diol followed by hydrolysis and dehydration. A series of polyimides (PIs) were synthesized from one‐step polycondensation of 1,2‐CHDPA with several aromatic diamines, such as 2,2′‐bis(trifluoromethyl)biphenyl‐4,4′‐diamine (TFDB), bis(4‐amino‐2‐trifluoromethylphenyl)ether (TFODA), 4,4′‐diaminodiphenyl ether (ODA), 1,4‐bis(4‐aminophenoxy)benzene (TPEQ), 4,4′‐(1,3‐phenylenedioxy)dianiline (TPER), 2,2′‐bis[4‐(3‐aminodiphenoxy)phenyl]sulfone (m‐BAPS), and 2,2′‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]sulfone (6F‐BAPS). The glass transition temperatures (T_gs) of the polymers were higher than 198°C, and the 5% weight loss temperatures (T_d5%s) were in the range of 424–445°C in nitrogen and 415–430°C in air, respectively. All the PIs were endowed with high solubility in common organic solvents and could be cast into tough and flexible films, which exhibited good mechanical properties with tensile strengths of 76–105 MPa, elongations at break of 4.7–7.6%, and tensile moduli of 1.9–2.6 GPa. In particular, the PI films showed excellent optical transparency in the visible region with the cut‐off wavelengths of 369–375 nm owing to the introduction of trans‐1,2‐cyclohexane moiety into the main chain. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42317.     

Synthesis and characterization of the soluble fluorescent poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)‐1,4‐phenylenevinylene]

A new soluble fluorescent polymer, poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyl‐oxy)naphthyl)‐1,4‐phenylenevinylene] (DDN‐PPV), with no tolane‐bisbenzyl (TBB) structure defects is prepared by the dehydrohalogenation of 1,4‐bis(bromomethyl)‐2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)benzene (as monomer) in this study. The aforementioned monomer is synthesized via such chemical reactions as alkylation, bromination, and Suzuki coupling reactions. The structure and properties of the DDN‐PPV are examined by ¹H NMR, FTIR, UV/vis, TGA, photoluminescence (PL), and electroluminescence (EL) analyses. The two asymmetric decyloxy and 6′‐dodecyloxynaphthyl substituents on the phenylene ring make the DDN‐PPV soluble in organic solvents and eliminate the TBB structure defects. With the DDN‐PPV acting as a light‐emitting polymer, a device is fabricated with a sequential lamination of ITO/PEDOT/DDN‐PPV/Ca/Ag. The EL spectrum of the device shows a maximum emission at 538 nm. The turn on voltage of the device is about 16.6 V. Its maximum brightness is 14 cd/m² at a voltage of 18.2 V. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2734–2741, 2007