Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Preparation of chlorinated poly(vinyl chloride)‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membranes and their water permeation properties

Chlorinated poly(vinyl chloride) (CPVC) membranes for microfiltration processes were prepared with the combined process of a solvent evaporation technique and the water‐vapor induced‐phase‐inversion method. CPVC membranes with a mean pore size of 0.7 μm were very hydrophobic. These membranes were subjected to surface modification by ultraviolet (UV)‐assisted graft polymerization with N‐vinyl‐2‐pyrrolidinone (NVP) to increase their surface wettability and decrease their adsorptive fouling. The grafting yields of the modified membranes were controlled by alteration of UV irradiation time and NVP monomer concentration. The changes in chemical structure between the CPVC membrane and the CPVC‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membrane and the variation of the topologies of the modified PVC membranes were characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, and field emission scanning electron microscopy. According to the results, the graft yield of the modified CPVC membrane reached a maximum at 5 min of UV exposure time and 20 vol % NVP concentration. The filtration behavior of these membranes was investigated with deionized water by a crossflow filtration measurement. The surface hydrophilicity and roughness were easily changed by the grafting of NVP on the surface of the CPVC membrane through a simultaneous irradiation grafting method by UV irradiation. To confirm the effect of grafting for filtration, we compared the unmodified and modified CPVC membranes with respect to their deionized water permeation by using crossflow filtration methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3188–3195, 2003     

Preparation of poly(vinyl chloride) (PVC) ultrafiltration membranes from PVC/additive/solvent and application of UF membranes as substrate for fabrication of reverse osmosis membranes

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC) as main polymer, poly(vinyl pyrrolidone) (PVP) as additive, and 1‐methyl‐2‐pyrrolidone (NMP) as solvent using Design Expert software for designing the experiments. The membranes were characterized by SEM, contact angle measurement, and atomic force microscopy. The performance of UF membranes was evaluated by pure water flux (PWF) and blue indigo dye particle rejection. In addition, the molecular weight cutoff of UF membranes was determined by poly(ethylene glycol) (PEG) rejection. The UF membranes were used as substrates for fabrication of polyamide thin film composite (TFC) reverse osmosis (RO) membranes. The results showed that the model had high reliability for prediction of PWF of UF membranes. Also, increment in PVC concentration caused reduction of PWF. Moreover, at constant PVC concentration and if the concentrations of PVC was lower than 10 wt %, the PWF reduced by increasing the concentration of PVP. However, at PVC concentration higher than 11 wt %, increment in PVP concentration showed increment and reduction of PWF. The PEG rejection results showed that the prepared membranes had UF membranes properties. Finally, the NaCl rejection tests of RO membranes by PVC as substrates indicated that the performance of RO membranes were lower than commercial membranes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46267.     

PEEKWC ultrafiltration hollow‐fiber membranes: Preparation,morphology, and transport properties

A series of hollow‐fiber membranes was produced by the dry–wet spinning method from PEEKWC, a modified poly(ether ether ketone) with good mechanical, thermal, and chemical resistance. The fibers were prepared under different spinning conditions, varying the following spinning parameters: polymer concentration in the spinning solution, height of the air gap, and bore fluid composition. The effect of these parameters on the water permeability, the rejection of macromolecules (using dextrane with an average molecular weight of 68,800 g/mol), and the morphology of the membranes was studied. The results were also correlated to the viscosity of the spinning solution and to the ternary polymer/solvent/nonsolvent phase diagram. The morphology of the cross section and internal and external surfaces of the hollow fibers were analyzed using scanning electron microscopy (SEM). All membranes were shown to have a fingerlike void structure and a skin layer, depending on the spinning conditions, varying from (apparently) dense to porous. Pore size measurements by the bubble‐point method showed maximum pore sizes ranging from 0.3 to 2 μm. Permeability varied from 300 to 1000 L/(h^?1 m^?2 bar) and rejection to the dextrane from 10 to 78%. The viscosity of polymer solutions was in the range of 0.2 to 3.5 Pa s. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 841–853, 2004     

Absorption of trioctyl trimellitate into mass‐polymerization and suspension‐polymerization poly(vinyl chloride)

Poly(vinyl chloride) (PVC) slush powder has been widely used; we prepared it by dry blending. We found that the absorption of plasticizer by the PVC resins was the most important factor in the dry‐blending process and, further, that different types of PVC resin had different absorption rates. This results of this study provide new information about the relationship of absorption to PVC and other parameters. Haake rheomix testing and the quantity of plasticizers absorbed by the PVC resins were used to characterize the absorption process. Suspension‐polymerization poly(vinyl chloride) (SPVC) and mass‐polymerization poly(vinyl chloride) (MPVC) in different sizes were used for the test. The results showed that the MPVC absorbed the plasticizer more quickly than SPVC, especially at a higher temperature. However, for the same PVC resin type, the absorbing speeds were nearly independent of particle size. The studies that used a scanning electric microscope and specific surface area revealed that the morphology of the two types of particles was different. The surfaces of the individual particles of SPVC were smoother than those of MPVC. There was a “skin” covering the SPVC particles, whereas with the MPVC particles, the primary polymer was exposed directly on the surface. This difference in morphology was shown to be a significant factor in the different rates of absorption of the plasticizers for the different PVC resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2369–2374, 2004     

Preparation and characterization of poly(vinyl chloride)‐graft‐acrylic acid membrane by electron beam

Poly(vinyl chloride) (PVC) was irradiated by electron beam in vacuum at 20 KGy to produce living free radicals, and then reacted with acrylic acid (AA) in solution to obtain the PVC‐g‐AA copolymers. The copolymers were characterized by Fourier transform infrared spectroscopy. Porous membranes were prepared from copolymers by the phase inversion technique. The morphology of PVC‐g‐AA membranes was studied by field emission scanning electron microscopy. The mean pore size and pore size distribution were determined by a mercury porosimeter. The mean pore size was 0.19 μm, and the bulk porosity was 56.02%. The apparent static water contact angle was 89.0°. The water drop penetration rate was 2.35 times to the original membrane. The maximum stress was 4.10 MPa. Filtration experiments were carried out to evaluate the fouling resistance of the PVC‐g‐AA membrane. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation,structure, and transport properties of ultrafiltration membranes of poly(vinyl chloride) (PVC), carboxylated poly(vinyl chloride) (CPVC), and PVC/CPVC blends

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC), carboxylated poly(vinyl chloride) (CPVC), and PVC/CPVC blends by the phase-inversion method. The physical structure of the membranes was characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The fouling characteristics of all the three membranes and acrylamide (AA)-grafted PVC membranes were characterized by ultrafiltration of bovine serum albumin (BSA) solution over a range of pH and of salt concentrations. Maximum adsorption of the protein on the membrane occurred near the isoelectric point of BSA and in the presence of the salts. The charge on BSA appears to be a dominant factor in determining the fouling. The UF results are explained in terms of nature of the membrane polymer, and effect of different ionic environments on the conformational changes of the protein. The ultrafiltration fluxes are correlated by a model based on the membrane resistance and the time-dependent resistance of the concentration polarization layer of the protein. The values of a mass transfer coefficient and concentration polarization were determined. Zeta potential of the membranes were also determined before and after the UF. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1117–1130, 1999     

Preparation and performance of braid‐reinforced poly(vinyl chloride) hollow fiber membranes

A novel braid‐reinforced (BR) poly(vinyl chloride) (PVC) hollow fiber membrane was fabricated via dry‐wet spinning process. The mixtures of PVC polymer solutions were uniformly coated on the tubular braid which contained polyester (PET) and polyacrylonitrile (PAN) fibers. The influences of braid composition on structure and performance of BR PVC hollow fiber membranes were investigated. The results showed that the prepared BR PVC hollow fiber membranes were composed of two layers which contained separation layer and tubular braid supported layer when the PET and PET/PAN hybrid tubular braids were used as the reinforcement. But the sandwich structure appeared when the PAN tubular braid was used as the reinforcement, which revealed outer separation layer, tubular braid supported layer and the inner polymer layer. The BR PVC hollow fiber membranes that prepared by PET/PAN hybrid tubular braid had favorable interfacial bonding state compared with the membrane prepared by pure PET or PAN tubular braid. The pure water flux of the BR PVC hollow fiber membranes that prepared by the PET/PAN hybrid tubular braid were lower than that prepared by pure PET or PAN tubular braid, but the rejection of Bovine serum albumin was opposite. The tensile strength of prepared BR PVC hollow fiber membrane was higher than 50 MPa. Both of the tensile strength and elongation at break decreased with the increase of the PAN filaments in the PET/PAN hybrid tubular braid. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45068.     

Effect of poly(vinyl chloride) resin type in the preparation process of slush powder

During the preparation of the poly(vinyl chloride) (PVC) slush powder, we found that PVC resins obtained by different polymerization methods affected many properties of slush powder and its products. Two types of commercial PVC resins were used for slush powder preparation: mass poly(vinyl chloride) (M‐PVC) and suspension poly(vinyl chloride) (S‐PVC). We used the Haake rheomix test to characterize the absorption of plasticizers into PVC resins, and the results showed that M‐PVC absorbed the plasticizers more quickly than S‐PVC. The fusion behavior of the two slush powders was studied by the thermal plate test and Haake rheomix test, and the results showed that the slush powder of M‐PVC was easier to fuse than that of S‐PVC. The different properties of the two resins and slush powder could be explained by the morphology, average size, and size distribution. Due to the “skin” of the particles' surfaces, the wider size distribution, and the large size of particles, S‐PVC absorbed the plasticizers more slowly and was more difficult to fuse. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3331–3335, 2002     

Rheology of poly(vinyl chloride) plastisol for superhigh shear‐rate processing. I

In coating operations with poly(vinyl chloride) plastisol, there is a high shear limit because the flow becomes unstable. However, there is an indication that the flow becomes stable at superhigh shear rates well past the unstable region. This article explores the effect of the particle size (with a similar size distribution spread) and the effect of the amount of the emulsifier on the flow at superhigh shear rates. It has been known that below the flow instability, larger particles lead to a lower viscosity, and an increased amount of the emulsifier leads to a higher viscosity. The question is whether or not the same trends persist at superhigh shear rates. Observations in this study confirm these trends. In addition, the emulsifier has been found to enhance the interparticle attraction. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Comparison of the toughening mechanisms of poly(vinyl chloride)/chlorinated polyethylene and poly(vinyl chloride)/acrylonitrile–butadiene–styrene copolymer blends

In this study, the influence of chlorinated polyethylene (CPE) and acrylonitrile–butadiene–styrene copolymer (ABS) on the mechanical properties of poly(vinyl chloride) (PVC)/CPE and PVC/ABS hybrids were examined. The experimental results show that the toughness of the hybrids could be modified greatly by the introduction of CPE or ABS. The microstructure and impact surfaces of the blends were investigated by scanning electron microscopy and transmission electron microscopy. ABS dispersed in the form of particles or agglomerates in the PVC matrix, and CPE tended to disperse as a net structure. In the tensile test, ABS initiated crazes as stress concentrators to toughen the PVC matrix, whereas CPE, with the PVC matrix together, caused a yield deformation by shear stress to form a shear band. The formation of crazes and shear bands benefited the toughening of PVC, but to the different extent. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 916–924, 2003     

Mechanochemical preparation of a novel polymeric photostabilizer for poly(vinyl chloride)

The preparation of a novel polymeric photostabilizer was carried out via the vibromilling of poly(vinyl chloride) (PVC) powder, a reactive light stabilizer (r‐LS), and a peroxide initiator in ball‐containing jars with a planetary ball mill for a certain time. The effects of the initiator content, milling time, and temperature on the grafting ratio were studied with gravimetric analysis and intrinsic viscosity measurements. Fourier transform infrared and ultraviolet–visible spectra were used to investigate the structural development of the mixture of the r‐LS and PVC during vibromilling. The results showed that the r‐LS was grafted onto PVC chains successfully, and the aforementioned factors had a significant effect on the grafting ratio. The optimum preparation conditions were 0.5 wt % initiator, 8 h, and 20°C. A grafting mechanism is proposed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improving the antifouling property of poly(vinyl chloride) membranes by poly(vinyl chloride)‐g‐poly(methacrylic acid) as the additive

To improve the antifouling property of poly(vinyl chloride) (PVC) membranes, a series of poly(methacrylic acid) grafted PVC copolymers (PVC‐g‐PMAA) with different grafting degree were synthesized via one‐step atom transfer radical polymerization process utilizing the labile chlorines on PVC backbones followed by one‐step hydrolysis reaction. PVC/PVC‐g‐PMAA blend membranes with different grafting degree and copolymer content were prepared by nonsolvent induced phase separation method. The surface chemical composition, surface charge, membrane structures, wettability, permeability, separation performances and the fouling resistance of blend membranes were carefully investigated. The results indicated that the PMAA chains were segregated towards the surface and the membranes were endowed with negative charge. The hydrophilicity and permeability of the blend membranes were obviously improved. Furthermore, the antifouling ability especially at neutral or alkaline environments was also significantly increased. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42745.     

Rheology of poly(vinyl chloride) plastisol for super‐high‐shear‐rate processing. II

Capillary flow of poly(vinyl chloride) plastisol was examined at low, high, and superhigh shear rates. At the low to intermediate shear rates, the flow was pseudo‐plastic, but the measured viscosity was not reproducible and widely scattered. The flow behavior was explained as the breakup of the particle network into network‐fragments of varying size. At high shear rates, the measured viscosity was reproducible and increased with shear rate, indicating that the particles were, by and large, separated from each other. At superhigh shear rates, the viscosity decreased with the increase of shear rate. The particles cease to participate in flow because rotation becomes more difficult. A plug‐flow ensues with a thin layer of lubricating plasticizer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of poly(vinyl chloride)–continuous carbon fiber composites

In this article, we report on the preparation and characterization of novel poly(vinyl chloride) (PVC)–carbon fiber (CF) composites. We achieved the reinforcement of PVC matrices with different plasticizer contents using unidirectional continuous CFs by applying a warm press and a cylinder press for the preparation of the PVC–CF composites. We achieved considerable reinforcement of PVC even at a relatively low CF content; for example, the maximum stress (σ_max) of the PVC–CF composite at a 3% CF content was found to be 1.5–2 times higher than that of the PVC matrix. There were great differences among the Young's modulus values of the pure PVC and PVC–CF composites matrices. The absolute Young's modulus values were in the range 1100–1300 MPa at a 3% CF content; these values were almost independent of the plasticizer content. In addition, we found a linear relationship between σ_max and the CF content and also recognized a linear variation of the Young's modulus with the CF content. The adhesion of CF to the PVC matrix was strong in each case, as concluded from the strain–stress curves and the light microscopy and scanning electron microscopy investigations. The mechanical properties of the PVC–CF composites with randomly oriented short (10 mm) fibers were also investigated. At low deformations, the stiffness of the composites improved with increasing CF content. Dynamic mechanical analysis (DMA) was used to determine the glass‐transition temperature (T_g) of the PVC–CF composites. The high increase in the Young's modulus entailed only a mild T_g increase. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

New ultraviolet‐curable formulations for bonding poly(vinyl chloride)‐coated fiberglass wire mesh for reinforcement applications

The advantages of the ultraviolet (UV)‐curing process are numerous, including a rapid cure, conservation of energy, environmental and user friendliness, and superior finish properties such as a high gloss and chemical and scuff resistance. In addition, the UV‐curing process offers flexibility suitable for sensitive substrates and complete screen stability because UV ink dries on exposure only to a UV‐energy source and not to ambient UV‐light sources such as sunlight or fluorescent shop lights. Industrial methods apply traditional heat setting to form mesh reinforcement structures from poly(vinyl chloride)‐coated fiberglass wires. The main defects of this method are the inefficiency and inconsistency of the process plus the huge consumption of power needed to generate the necessary thermal energy to bond the wire mesh. The heating process also causes quicker degradation of the wire and shortens the lifetime of the product. The purpose of this current innovative work is to replace this defective heat‐setting method with the more efficient and very advantageous method of applying UV‐curable coatings for this task. The obtained results are prospective for this endeavor, covering the issues of energy conservation, the economy of the process, and the improved mechanical properties of the finished product. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Formation of conjugated carbon bonds on poly(vinyl chloride) films by microwave‐discharge oxygen‐plasma treatments

Conjugated polyene bonds on poly(vinyl chloride) (PVC) films were rapidly formed by the treatment of oxygen plasma produced by microwave discharge. Changes affecting the formation of conjugated carbon bonds on PVC were studied with respect to plasma emission diagnostic and surface properties of the film with fluorescence, refractant absorption spectroscopy, X‐ray photoelectron spectroscopy analysis, and Raman spectroscopy. The formation of polyene bonds on the film surface was responsible for both the dechlorination and dehydrogenation of PVC in the plasma atmosphere. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 589–594, 2005     

硅烷交联聚氯乙烯的研究

研究了硅烷的种类,增塑剂,交联时间等因素对PVC交联的影响,结果表明,通过调节硅烷的用量可以制备不同交联度的PVC,交联后的PVC其力学性能,尺寸稳定性,体积电阻率,热主为形温度得到提高。     

Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder

Blends of poly(vinyl chloride) (PVC) with varying contents of plasticizer and finely ground powder of waste nitrile rubber rollers were prepared over a wide range of rubber contents through high‐temperature blending. The effects of rubber and plasticizer (dioctyl phthalate) content on the tensile strength, percentage elongation, impact properties, hardness, abrasion resistance, flexural crack resistance, limiting oxygen index (LOI), electrical properties, and breakdown voltage were studied. The percentage elongation, flexural crack resistance, and impact strength of blends increased considerably over those of PVC. The waste rubber had a plasticizing effect. Blends of waste plasticized PVC and waste nitrile rubber showed promising properties. The electrical properties and LOI decreased with increasing rubber and plasticizer content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1552–1558, 2004     

Nonaqueous polymerization of vinyl chloride: An environmentally friendly process

Poly(vinyl chloride) (PVC) is produced via a nonaqueous polymerization process in which hexane is used as a diluent. This nonaqueous process can lead to significant energy savings, significant reductions in carbon dioxide emissions, and the elimination of wastewater. Various suspending agents have been used to evaluate their effects on the shape and morphology of PVC grains. The nonaqueous process leads to the formation of PVC grains with higher porosity than that of typical suspension PVC. The bulk density is slightly lower than that of suspension PVC, but the thermal stability seems to be similar. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009