Electrochemical immobilization of ascorbate oxidase in poly(3,4‐ethylenedioxythiophene)/multiwalled carbon nanotubes composite films

Immobilization of ascorbate oxidase (AO) in poly(3,4‐ethylenedioxythiophene) (PEDOT)/multiwalled carbon nanotubes (MWCNTs) composite films was achieved by one‐step electrochemical polymerization. The PEDOT/MWCNTs/AO modified electrode was fabricated by the entrapment of enzyme in conducting matrices during electrochemical polymerization. The PEDOT/MWCNTs modified electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The experimental results showed that the composite films exhibited better mechanical integrity, electrochemical activity, higher electronic and ionic conductivity, and larger redox capacitance compared with pure PEDOT films, which would be beneficial to the fabrication of PEDOT/MWCNTs/AO electrochemical biosensors. The scanning electron microscopy studies revealed that MWCNTs served as backbone for 3,4‐ethylenedioxythiophene (EDOT) electropolymerization. Furthermore, the resulting enzyme electrode could be used to determine L ‐ascorbic acid successfully, which demonstrated the good bioelectrochemical catalytic activity of the immobilized AO. The results indicated that the PEDOT/MWCNTs composite are a good candidate material for the immobilization of AO in the fabrication of enzyme‐based biosensor. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanically enhanced electrically conductive films from polymerization of 3,4‐ethylenedioxythiophene with wood microfibers

This study was aimed at enhancing the mechanical properties of poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonate) (PEDOT:PSS) using wood microfibers. Ultra fine friction grinding was conducted on wood particles to reduce their size to the micron scale and to induce fibrillation. Oxidative polymerization was performed on 3,4‐ethylenedioxythiophene (EDOT) monomer at seven dosages based on the content of microfibers in the formulation. The presence of PEDOT:PSS in the prepared films was verified by infrared spectroscopy and scanning electron microscopy. The composite films became stronger and stiffer as the fiber content increased. An EDOT:microfibers ratio of 33 wt % was considered the best among the seven tested levels, judging from their low sheet resistivity (340 Ω/sq.) and favorable tensile properties (38 MPa strength and 4.8 GPa stiffness). The selected films were also tested for their resistance to solvents to obtain information about their potential use in different environments. Among the tested solvents, sodium hydroxide greatly decreased the film conductivity. It also had the harshest effect on reducing the weight of the film. Findings from this study demonstrate the successful use of wood microfibers alternative to synthetic substrates and cellulose nanofiber as a supportive and reinforcing material for electrically conductive polymers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45127.     

Non-covalent modification of graphene sheets in PEDOT composite materials by ionic liquids

An ionic liquid (IL) supported composite of poly(3,4-ethylene dioxythiophene) (PEDOT) and graphene oxide (GO) is presented. GO was dispersed in ILs and electropolymerization carried out after loading of EDOT to the dried dispersion. The content of GO was optimized to obtain high electrical conductivity of the composite material. The IL acts as the dispersant for GO and as dopant in the synthesis of PEDOT leading to films with a highly porous structure indicated from the scanning electron microscopy (SEM) images. Subsequently, GO was reduced electrochemically by cyclic voltammetry to obtain PEDOT/rGO composite films. The successful formation of composite materials was confirmed using Raman and X-ray photoelectron spectroscopy (XPS) techniques. XPS was also used to verify removal of oxygen-containing functional groups upon electrochemical reduction of the composite films. The electrochemical properties of PEDOT, PEDOT/GO and PEDOT/rGO were studied using cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The results show that electrochemical reduction clearly increases the capacitance of the composite and furthermore the cycling stability. Such an increase could be obtained if >20 cycles, extending to highly negative potentials (−2.0 V), was used during the electroreduction of incorporated GO. Owing to the high porosity, favorable electrochemical properties and cycling stability these hybrid materials shows great potential towards supercapacitor applications.     

Multicolor electrochromism of low‐bandgap copolymers based on pyrrole and 3,4‐ethylenedioxythiophene: Fine‐tuning colors through feed ratio

The copolymerization of pyrrole with 3,4‐ethylenedioxythiophene (EDOT) is successfully achieved in boron trifluoride diethyl etherate via direct anodic oxidation of the monomer mixtures on indium‐tin oxide working electrodes. The resultant copolymers are characterized by electrochemical methods, FT‐IR, XPS, SEM, and spectroelectrochemical analysis. The copolymer films present excellent electrochromic properties especially the multicolor electrochromism which can be tuned through the feed ratio of pyrrole and EDOT. The neutral copolymer films exhibit blue‐shift with the increasing feed ratio of pyrrole and EDOT, and the calculated band gaps of the copolymers are as low as that of PEDOT film. Furthermore, the electrochemical and optical stability has been improved by the incorporation of EDOT units into the polymer chains. The copolymer prepared with the changing feed ratio of pyrrole and EDOT at 1/4 retains 71% of its original electroactivity after 500 cycles and 72% of its optical contrast after 500 steps. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Fluorinated functionalized EDOT-based conducting films

Three ethylenedioxithiophene (EDOT) derivatives bearing either perfluoro- or ether perfluoro-alkyl chains were synthesized with the objective to prepare films with dry and chemically immobilized lubrication properties. The corresponding fluorinated PEDOT films were deposited on platinum surface by electropolymerization. Cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM) analyses (both quartz resonant frequency and resonant admittance) of the growing steps are described. The electroactive behavior of the films versus their doping level was followed by electrochemical impedance spectroscopy (EIS) through equivalent circuit fitting procedure and compared to their CV responses. Hysteresis in fit parameters corresponding to capacity and film resistance between the forward and the backward scans are observed and discussed. Control of the chemical structures and charge effects on PEDOT chains are followed by an XPS analysis. From these analyses, it appears that the fluorinated side-arm does not alter both the growing and the electrical properties of the films in respect to the pristine PEDOT taken as reference.     

Preparation and performance of a transparent poly(3,4‐ethylene dioxythiophene)–poly(p‐styrene sulfonate‐co‐acrylic acid sodium) film with a high stability and water resistance

Poly(p‐styrene sulfonate‐co‐acrylic acid sodium) (PSA) from the copolymerization of acrylic acid sodium and p‐styrene sulfonate monomers were used to dope poly(3,4‐ethylene dioxythiophene) (PEDOT) to generate PEDOT–PSA antistatic dispersions. Compared to those of the PEDOT–poly(p‐styrene sulfonate sodium) (PSS), the physical and electrical properties of the PEDOT–PSA conductive liquids were much better. The PEDOT–PSA films possessed a better water resistance without a decrease in the conductivity. The sheet resistance of the PEDOT–PSA–poly(ethylene terephthalate) (PET) films was about 1.5 × 10⁴ Ω/sq with a 100 nm thickness, the same as the PEDOT–PSS–PET films. The transmittance of the PEDOT–PSA–PET films exceeded 88%. Furthermore, the environmental dispersity of the PEDOT–PSA antistatic dispersion was apparently improved by the dopant PSA so that the stability was extraordinarily promoted. Meanwhile, the water resistances of the PEDOT–PSA–PET and PEDOT–PSA films were also enhanced. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45163.     

Surface polymerization of (3,4-ethylenedioxythiophene) probed by in situ scanning tunneling microscopy on Au(111) in ionic liquids

The electropolymerization of 3,4-ethylenedioxythiophene (EDOT) to poly(3,4-ethylenedioxythiophene) (PEDOT) was investigated in the air and water-stable ionic liquids 1-hexyl-3-methylimidazolium tris(pentafluoroethyl) trifluorophosphate [HMIm]FAP and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) amide [EMIm]TFSA. In situ scanning tunnelling microscopy (STM) results show that the electropolymerization of EDOT in the ionic liquid can be probed on the nanoscale. In contrast to present understanding, it was observed that the EDOT can be oxidised in ionic liquids well below its oxidation potential and the under potential growth of polymer was visualized by in situ STM. These results serve as the first study to confirm the under potential growth of conducting polymers in ionic liquids. Furthermore, ex situ microscopy measurements were performed. Quite a high current of 670 nA was observed on the nanoscale by conductive scanning force microscopy (CSFM).     

Specroelectrochemical,switching kinetics,and chronoamperometric studies of dibenzyl derivative of poly(3,4‐propylenedioxythiophene) thin‐film‐based electrochromic device

The dibenzyl derivative of poly(3,4‐propylenedioxythiophene) (PProDOT‐Bz₂) thin film is deposited onto ITO‐coated glass substrate by electropolymerization technique. The electropolymerization of ProDOT‐Bz₂ is carried out by a three‐electrode electrochemical cell. The cyclic voltammogram shows the redox properties of electrochemically prepared films deposited at different scan rates. The thin films prepared were characterized for its morphological properties to study the homogeniety. Classic six‐layer structure of PProDOT‐Bz₂ electrochromic device using this material was fabricated and reported for the first and its characterizations such as spectroelectrochemical, switching kinetics, and chronoamperometric studies are performed. The color contrast of the thin film and the device achieved are 64 and 40%, respectively, at λ_max (628 nm). The switching time is recorded and the observed values are 5 s from the coloring state to the bleaching state and vice versa. The chronoamperometry shows that the device performed up to 400 cycles, and it is capable of working up to 35 cycles without any degradation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40717.     

Electrochromic properties of a copolymer of 1‐4‐di[2,5‐di(2‐thienyl)‐1H‐1‐pyrrolyl]benzene with EDOT

Homopolymer of 1‐4‐di[2,5‐di(2‐thienyl)‐1H‐1‐pyrrolyl]benzene and its copolymer with 3,4‐ethylenedioxythiophene (EDOT) were electrochemically synthesized and characterized. Resulting homopolymer and copolymer films have distinct electrochromic properties. At the neutral state, homopolymer has λ_max due to the π‐π* transition as 410 nm and E_g was calculated as 2.03 eV. The resultant copolymer revealed multichromism through the entire visible region, displaying red‐violet, brownish yellow green, and blue colors with the variation of the applied potential. For the copolymer, λ_max and E_g were found to be 450 nm and 1.66 eV, respectively. Double potential step chronoamperometry experiment shows that homopolymer and copolymer films have good stability, fast switching times, and high optical contrast in NIR region as 41 and 30%, respectively. Copolymerization with EDOT not only decreases the band gap, E_g, but also enhances the electrochromic properties. Hence, electrochemical copolymerization is considered to be a powerful tool to improve the electrochromic properties of N‐substituted 2,5‐di(2‐thienylpyrrole) derivatives. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrical conductivity of poly(3,4-ethylenedioxythiophene):p-toluene sulfonate films hybridized with reduced graphene oxide

Reduced graphene oxide-poly(3,4-ethylenedioxythiophene):p-toluene sulfonate (rGO-PEDOT:PTS) hybrid electrode films were synthesized directly on a substrate by interfacial polymerization between an oxidizing solid layer and liquid droplets of 3,4-ethylenedioxythiophene (EDOT) produced by electrospraying. The EDOT reduced the graphene oxide by donating electrons during its transformation into PEDOT:PTS, and hybrid films consisting of rGO distributed in a matrix of PEDOT:PTS were obtained. These rGO-PEDOT:PTS hybrid films showed excellent electrical conductivities as high as 1,500 S/cm and a sheet resistance of 70 Ω sq^-1. The conductivity values are up to 50% greater than those of films containing conductive PEDOT:PTS alone. These results confirm that highly conductive rGO-PEDOT:PTS hybrid films can potentially be used as organic transparent electrodes.     

Electropolymerization and properties of 3,4‐ethylenedioxythiophene backbone polymer with tetrathiafulvalene as pendant

Three 3,4‐ethylenedioxythiophene (EDOT) derivatives, including an EDOT‐tetrathiafulvalene (TTF) derivative, were synthesized by Steglich esterification of carboxylic acids with hydroxymethyl EDOT (3,4‐ethylenedioxythiophene methanol). The UV spectra showed that there was no distinctive intramolecular interaction for the EDOT–TTF monomer between the EDOT and the TTF moieties in the ground state; however, the cyclic voltammetry responses implied that such intramolecular interaction occurred. Electropolymerization in excessive potential could bring in strong overoxidation effects and degradation in the polymer film. The polymers were simulated using density functional theory with Gaussian03 package and the optimized HOMO and LUMO state were figured out. The conductivity of TTF‐polymer was 6 S·cm^?1 obtained by galvano station and 4.8 × 10^?3 S·cm^?1 obtained by potentiostatic electropolymerization after doping with 7,7,8,8‐tetracyanoquinodimethane. The results indicated that this polymer was a reasonable candidate for conducting materials and it was meaningful to increase the conductive dimensions of TTF polymers by chemical doping. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of alcoholic solvents on the conductivity of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs)

The effects of alcoholic solvents on the charge transport properties of tosylate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐OTs) are investigated. The use of different alcoholic solvents in the oxidative chemical polymerization of 3,4‐ethylenedioxythiophene (EDOT) with iron(III)‐p‐tosylate led to a change in the electrical conductivity of PEDOT‐OTs. For example, PEDOT‐OTs prepared from methanol shows a conductivity of 20.1 S cm^?1 which is enhanced by a factor of 200 as compared to PEDOT‐OTs prepared from hexanol. The variation of charge transport properties on the use of different alcoholic solvents is consistent with the data recorded by UV‐visible and electrospin resonance (ESR) measurements. From XPS experiments, the PEDOT‐OTs samples prepared from different alcoholic solvents were found to have almost the same doping level, suggesting that the number of charge carriers is not responsible for the change in conductivity. Supported by XRD results, it was found that the use of alcoholic solvents with shorter chain length induces more efficient packing of PEDOT chains. It is proposed that the alcoholic solvents associated with the counter ion of PEDOT via hydrogen bonding give rise to a change in the molecular ordering of PEDOT chains during the polymerization step, hence enhancing or depressing the inter‐chain hopping rate of the resulting PEDOT‐OTs. Copyright © 2005 Society of Chemical Industry     

Preparation of thermally curable conductive films PEDOT:P(SS-NMA) and their performances on weather stability and water resistance

In this research, sodium 4-styrenesulfonate (SSNa) and N-(methylol acrylamide) (NMA) were copolymerized to form the thermally curable copolymer P(SS-NMA). Moisture absorptivity and swelling index were used to evaluate the weather stability of P(SS-NMA). The P(SS-NMA) copolymers with high molar content of NMA exhibited better weather stability. Then, P(SS-NMA) was used as the polymeric template to carry out the oxidative polymerization of 3,4-ethylenedioxythiophene (EDOT) and yielded the thermally curable conductive dispersion, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate-N-(methylol acrylamide)) (PEDOT:P(SS-NMA)). The optoelectronic property and surface morphology for the PEDOT:P(SS-NMA) conductive thin films were investigated. In addition, the performance of the PEDOT:P(SS-NMA) conductive film was characterized in the two parts: weather stability and water resistance. The introduction of crosslinking structures into the conductive film improved the mechanical property and weather stability so as to resolve the drawbacks of the commercial products PEDOT:PSS.     

Preparation and characterisation of poly(3,4-ethylenedioxythiophene) and poly(3,4-ethylenedioxythiophene)/poly(neutral red) modified carbon film electrodes, and application as sensors for hydrogen peroxide

Poly(3,4-ethylenedioxythiophene) (PEDOT) films have been prepared for the first time on carbon-film electrodes (CFE) in aqueous solution using electropolymerisation by potential cycling, potentiostatically and galavanostatically. Characterisation of the modified electrodes was done by cyclic voltammetry and electrochemical impedance spectroscopy and the stability of the polymer films was probed. The coated electrodes were tested for application as hydrogen peroxide sensors, by oxidation and reduction. A novel polymer film was also formed by modification of CFE by co-electropolymerisation of EDOT and the phenazine dye neutral red (NR) – (PEDOT/PNR) with a view to enhancing the properties for sensor applications. It was found that hydrogen peroxide reduction at the PEDOT/PNR coated electrodes could be carried out at a less negative potential, the sensor performance comparing very favourably with that of other polymer-modified electrodes reported in the literature.     

Copolymer from electropolymerization of thiophene and 3,4-ethylenedioxythiophene and its use as cathode for lithium ion battery

Electropolymerizations (EPs) of thiophene (Th), 3,4-ethylenedioxythiophene (EDOT) and the mixed monomers of Th and EDOT in 0.05 M Et₄NClO₄/propylene carbonate (PC) solution were performed to prepare polymer films as potential cathode materials in lithium ion battery. The incorporation of EDOT units into pure polythiophene (PTh) chain leads to large alternations on the experimental conditions of EPs and the properties of the resulting polymer films. Onset potential of the EPs was reduced with the participation of EDOT component. The resulting polymers, PTh, poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(thiophene-co-3,4-ethylenedioxythiophene) (PTh-EDOT) were then served as cathode materials to test their capabilities to transport lithium ion in 1.0 M LiPF₆/ethylene carbonate/dimethyl carbonate solution. With the inherent EDOT unit, PEDOT and PTh-EDOT have better charge capacity, stability and response rate than pure PTh. Among the copolymers, PTh-EDOT (1/1) even shows better stability than pure PEDOT homopolymer, advantage of using EDOT as copolymer component is thus evaluated.     

Capacitance properties of graphite oxide/poly(3,4‐ethylene dioxythiophene) composites

Poly(3,4‐ethylene dioxythiophene) (PEDOT) and graphite oxide (GO)/PEDOT composites (GPTs) doped with poly(sodium styrene sulfate) (PSS) were synthesized by in situ polymerization in aqueous media. The electrochemical capacitance performances of GO, PEDOT–PSS, and GPTs as electrode materials were investigated. The GPTs had a higher specific capacitance of 108 F/g than either composite constituent (11 F/g for GO and 87 F/g for PEDOT–PSS); this was attributable to its high electrical conductivity and the layer‐within/on‐layer composite structure. Such an increase demonstrated that the synergistic combination of GO and PEDOT–PSS had advantages over the sum of the individual components. On the basis of cycle‐life tests, the capacitance retention of about 78% for the GPTs compared with that of 66% for PEDOT–PSS after 1200 cycles suggested a high cycle stability of the GPTs and its potential as an electrode material for supercapacitor applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and electro-optical properties of a new copolymer based on EDOT and carbazole

A new copolymer of 3,4-ethylenedioxythiophene (EDOT) and 5-(2-ethylhexyl)-1,3-bis(9-methyl-9H-carbazol-3-yl)-5H-thieno[3,4-c]pyrrole-4,6-dione (CzPDICz) was electrochemically synthesized using different monomer feed ratios. The resulting copolymer films were investigated in terms of their electrochemical and electro-optical behaviors. Properties of the obtained copolymer films through different monomer feed ratios were compared to each other and to individual poly(ethylenedioxythiophene; PEDOT) and homopolymer of CzPDICz in order to observe the differences in the properties with respect to PEDOT and P(CzPDICz). Copolymers exhibited well adherence on the electrode surface with having non-diffusional redox process. The monomer feed ratios were prepared as 9:1; 4:1, and 1:1 (EDOT:CzPDICz) and changes in the electrochemical and spectroelectrochemical behavior were noted with increasing CzPDICz ratio in the monomer mixture. Although no appreciable change in the optical band gap values of the copolymers was noted as compared to PEDOT, the neutral blue copolymers exhibited grayish color in their semi-oxidized states and transparent green in their fully oxidized states.     

Poly(aspartic acid) Biohydrogel as the Base of a New Hybrid Conducting Material

In the present study, a composite made of conducting polymer, poly(3,4-ethylenedioxythiophene) (PEDOT), and a biodegradable hydrogel of poly(aspartic acid) (PASP) were electrochemically interpenetrated with poly(hydroxymethyl-3,4-ethylenedioxythiophene) (PHMeDOT) to prepare a new interpenetrated polymer network (IPN). Different cross-linker and PEDOT MPs contents, as well as different electropolymerization times, were studied to optimize the structural and electrochemical properties. The properties of the new material, being electrically conductive, biocompatible, bioactive, and biodegradable, make it suitable for possible uses in biomedical applications.     

Sol–Gel‐Derived High‐Performance Stacked Transparent Conductive Oxide Thin Films

Single‐ and multi‐layer transparent conductive oxide (TCO) thin films exhibiting high performance, good packing density and low surface/interface roughness are deposited on silica glass substrates by the sol–gel method. The crystal and microstructural properties of the TCO thin films are evaluated as an alternate to films prepared by ultra‐high vacuum deposition. Tin‐doped indium oxide (ITO) thin films produced using a two‐step drying process showed low surface roughness because of dense packing structure not only horizontal but also vertical directions. As a result, electrical conductivity, carrier concentration, carrier mobility, and optical transmittance of 2.3 × 10³ S/cm, 8 × 10²⁰ cm^?3, 18 cm²/Vs, and over 98% at 500 nm, respectively, were achieved. A multilayer ZnO/ITO stacked structure was also fabricated using the sol–gel process. Our findings suggest that solution‐based methods show promise as an alternative to existing ultra‐high vacuum methods to fabricate TCO thin films.     

Highly aligned poly(3,4-ethylene dioxythiophene) (PEDOT) nano- and microscale fibers and tubes

This study reports a facile method for the fabrication of aligned poly(3,4-ethylene dioxythiophene) (PEDOT) fibers and tubes based on electrospinning and oxidative chemical polymerization. Discrete PEDOT nano- and microfibers and nano- and microtubes are difficult to fabricate quickly and reproducibly. We employed poly(lactide-co-glycolide) (PLGA) polymers that were loaded with polymerizable 3,4-ethylene dioxythiophene (EDOT) monomer to create aligned nanofiber assemblies using a rotating glass mandrel during electrospinning. The EDOT monomer/PLGA polymer blends were then polymerized by exposure to an oxidative catalyst (FeCl₃). PEDOT was polymerized by continuously dripping a FeCl₃ solution onto the glass rod during electrospinning. The resulting PEDOT fibers were conductive, aligned and discrete. Fiber bundles could be easily produced in lengths of several centimeters. The PEDOT sheath/PLGA core fibers were immersed in chloroform to remove the PLGA and any residual EDOT resulting in hollow PEDOT tubes. This approach made it possible to easily generate large areas of aligned PEDOT fibers/tubes. The structure and properties of the aligned assemblies were measured using optical microscopy, electron microscopy, Raman spectroscopy, thermal gravimetric analysis, and DC conductivity measurements. We also demonstrated that the aligned PEDOT sheath/PLGA core fiber assemblies could be used in supporting and directing the extension of dorsal root ganglia (DRG) neurons in vitro.