热介质老化对HNBR力学性能的影响

采用加速老化实验方法研究了热介质对氢化丁腈橡胶（HNBR）材料力学性能的影响,获得了热空气、ASTM 1#标准油和ASTM 3#标准油中老化温度及老化时间对HNBR材料力学性能的影响规律。结果表明,HNBR材料具有良好的力学性能和耐油性能。     

热氧老化对特种氟橡胶交联结构及力学性能的影响

采用加速老化实验方法对特种氟橡胶密封材料的热氧老化性能进行了研究,获得了不同老化温度及老化时间对特种氟橡胶力学性能和交联结构的影响规律。研究结果表明,氟橡胶在热空气中老化时随老化温度的升高和老化时间的延长,材料的拉伸强度、硬度降低,100%定伸应力先增加后减小,拉断伸长率先减小后增大,回弹性和压缩永久变形增大。材料的交联密度先增加后减少,表明氟橡胶在热氧老化初期以交联为主,在老化后期以降解为主。     

Morphology and mechanical and viscoelastic properties of rubbery epoxy/organoclay montmorillonite nanocomposites

The morphology and mechanical and viscoelastic properties of rubbery epoxy/organoclay montmorillonite (MMT) nanocomposites were investigated with wide‐angle X‐ray scattering (WAXS), transmission electron microscopy (TEM), tensile testing, and dynamic mechanical thermal analysis. An ultrasonicator was used to apply external shearing forces to disperse the silicate clay layers in the epoxy matrix. The first step of the nanocomposite preparation consisted of swelling MMT in a curing agent, that is, an aliphatic diamine based on a polyoxypropylene backbone with a low viscosity for better diffusion into the intragalleries. Then, the epoxy prepolymer was added to the mixture. Better dispersion and intercalation of the nanoclay in the matrix were expected. The organic modification of MMT with octadecylammonium ions led to an increase in the initial d‐spacing (the [d₀₀₁] peak) from 14.4 to 28.5 Å, as determined by WAXS; this indicated the occurrence of an intercalation. The addition of 5 phr MMTC18 (MMT after the modification) to the epoxy matrix resulted in a finer dispersion, as evidenced by the disappearance of the diffraction peak in the WAXS pattern and TEM images. The mechanical and viscoelastic properties were improved for both MMT and MMTC18 nanocomposites, but they were more pronounced for the modified ones. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 103: 3547–3552, 2007     

Thermal aging on mechanical properties and crosslinked network of natural rubber/zinc Dimethacrylate composites

This article dealt with the relationship between mechanical properties and crosslinked networks of natural rubber (NR) reinforced by zinc dimethacrylate (ZDMA) after thermal aging. After thermal aging at the present experimental conditions, the covalent crosslink density showed a decrease all the time, whereas the ionic crosslink density was stable at 80°C but decreased at a higher temperature. The decrease in the total crosslink density after aging indicates the degradation of the crosslinked network. However, an experimental phenomenon observed was that the tensile strength and tear strength increased in a certain degree after aging at 80°C or at a 100°C for a short time. In addition, the thermal stability of the NR/ZDMA composite was evaluated by thermal gravimetric analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of silica loading on the mechanical properties and resistance to oil and thermal aging of CR/NR blends

Blends of 75/25 chloroprene rubber(CR)/natural rubber (NR) filled with various loadings of precipitated silica were prepared and their processability and mechanical properties as well as their resistance to thermal aging and oil were determined. The blend morphology was also studied using the atomic force microscopy technique. The results reveal that the mixing energy and the Mooney viscosity of the compound are increased continuously with increasing silica loading. It is also found that both scorch and optimum curing times are shortened while the total crosslink density is increased with increasing silica loading. The positive effect on cure could be explained by the chemical reaction between the allylic chlorine atom of CR and the silanol group on silica surface. The tensile strength, modulus, and hardness of the blend vulcanizate are noticeably improved while the compression set at elevated temperature is impaired with increasing silica loading. The results also reveal that both thermal aging resistance and oil resistance of the blend vulcanizates, as represented by the relative properties, are enhanced with the addition of silica. The resistance enhancement is believed to arise from the combination of the dilution effect, the increased crosslink density and also the reduction of NR dispersed phase size. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Variations in mechanical properties of an epoxy adhesive on exposure to warm moisture

The detrimental effects of a humid environment on the mechanical properties of adhesives have been investigated for many years. However, from early studies to recent contributions most of the interest has been focused on the reduction of strength related to plasticity associated with moisture uptake, interfacial weakening, etc. Much less attention has been paid to variations of elastic constants, which influence both the stiffness of the joint and the distribution of stresses. The goal of this study was to measure the effects of a humid and warm environment on tensile strength, Young's modulus and Poisson's ratio of a two-component epoxy adhesive, Henkel Hysol 3425. The measurements have been carried out on bulk specimens of dogbone shape, instrumented with two-grid (axial/transverse) strain gauge rosettes and tested in tension. The conditions of exposure, generated in a climatic cabinet, were 100% relative humidity and 50?°C. To relate the exposure time to the moisture uptake, the weight of the specimens was monitored. It has been noticed that most of the water uptake occurs in the first week of exposure; however, at progressively slower rate, the phenomenon is noticeable almost until the fourth week and then saturation is achieved. Over the same period, the mechanical properties decay as moisture uptake continues; at the end, the loss in strength is about 75% whilst for the elastic moduli the loss is approximately 20%. No clear evidence is found about the Poisson's ratio, which exhibits a non-monotonic behaviour: stable in the early weeks, then increasing and decreasing of a few per cent. In accord with previous works, the behaviour of the mechanical properties seems to be governed by the amount of moisture uptake.     

Physical aging of partially crosslinked RTM6 epoxy resin

The aging behavior of partially and completely crosslinked RTM6 epoxy resin samples in the glassy state is investigated by thermophysical and mechanical analyses. Curing degree, glass transition temperature, density, and micromechanical modulus are investigated as function of aging period, initial curing degree or depth below the sample surface. A clear increase of density and modulus with aging period as well as an enhanced surface stiffness is detected for all curing degrees. Also, the aging period necessary to achieve the steady state modulus is independent from the curing degree. In contrast, the degree of physical aging induced modulus changes shows a significant dependence on the curing degree. A discontinuity is detected in the so‐called transition region, which is related to the transition from rubber to glassy state during crosslinking. This emphasizes the importance of curing history for physical aging processes and the high potential of partial curing for the development of new processing routes, in particular for production of samples with low sensitivity to physical aging. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41121.     

Effects of various polyurethanes on the mechanical and structural properties of an epoxy resin

Polyurethanes (PURs) obtained from poly(ethylene glycol)s (PEGs) and polyoxypropylene diols (POPDs) of different molecular weights were used as modifiers of diglycidyl ether of bisphenol A. The impact strength, critical stress intensity factor, stress, and strain during three‐point bending were measured as functions of the PUR type and content. Scanning electron microscopy and infrared spectroscopy were employed for the structure and morphology analysis. The addition of 10 or 15% PUR to the epoxy resin resulted in the most enhanced mechanical properties. However, a modifier loading higher than 15% led to decreases in the impact strength, critical stress intensity factor, and flexural strength. Moreover, shorter flexible segments in PUR obtained from lower molecular weight PEG led to stronger composites, whereas composites containing PUR based on lower molecular weight POPD with long flexible segments exhibited higher toughness and strain at break and lower impact strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improvement of mechanical performance of epoxy resins filled with cobalt and chromium powders

Epoxy/ powder metal composites have interesting electrical properties, becoming conductors above the percolation threshold. To complete this study, mechanical investigations have been carried out to show the influence of the fillers on the mechanical performance of these composites. In this framework, different epoxy/metallic powders (Cobalt, Chromium) composites were prepared. Scanning Electron Microscopy showed that the dispersion of the metallic fillers in the matrix is almost homogeneous. The dynamic mechanical thermal analysis (DMTA) measurements showed the dependence of the viscoelastic parameters with the frequency, temperature, nature, and content of fillers. The main relaxations observed are the primary α relaxation (associated to the glass transition, T_g) and a secondary β relaxation. A second DMTA run on the same samples showed a slight increase of the T_g. It clearly showed that the used metallic fillers improve the mechanical properties of the obtained composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The influence of latex blend composition on crosslinking and mechanical properties

Model reactive latices were synthesized by semicontinuous emulsion copolymerization of n‐butyl methacrylate and acetoacetoxyethyl methacrylate or dimethylaminoethyl methacrylate. The two functional latices were then blended in various ratios to study the influence of blend composition on crosslinking and mechanical properties of the resulting films. Crosslinking was quantified through swelling measurements. It was found that the crosslink density increased with increasing amounts of acetoacetoxy‐functional polymer. In addition, the crosslink density exhibited two maxima, at 30/70 and 70/30 (acetoacetoxy‐functional latex/amino‐functional latex) blend compositions. The mechanical properties of the films were quantified by dynamic mechanical analysis (DMA). It was shown that optimal mechanical properties occurred when the particles packed most efficiently at the 30/70 and 70/30 blend compositions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3774–3779, 2007     

高低温老化对碳纤维复合材料芯棒结构性能的影响

采用拉挤工艺制备了碳纤维增强环氧树脂基复合材料芯棒,并对其进行高低温人工加速老化试验,以及对老化前后碳纤维复合材料芯棒的横截面、外观颜色和密度进行了测试和分析。结果表明,高低温老化使芯棒颜色加深,主要对芯棒的外层产生一定的影响,内部结构没有明显变化;老化后芯棒的密度比老化前减小约2.5%,并且不同老化周期对芯棒的密度基本不变。     

Multifunctionalization of novolac epoxy resin and its influence on dielectric,thermal properties,viscoelastic, and aging behavior

In this article, novolac epoxy was functionalized using p‐hydroxybenzoic acid as pendent groups, which offered weak acidic environment and were cured with methyl etherified amino resin (HMMM). Its chemical structure was characterized by Fourier transform infrared (FT‐IR), ¹H nuclear magnetic resonance (¹H NMR) and differential scanning calorimeter (DSC). To comprehensively investigate its performance, HMMM was used as a curing agent. The modified epoxy exhibited higher storage modulus, lower thermal expansion coefficient, better moisture resistance, better resistance to degradation and lower dielectric constant. Furthermore, the aging behavior was investigated using dynamic mechanical analysis and scanning electron microscopy, which showed that the activation energy of glass transition increased after aging and cured MDEN was more difficult to age. Moreover, the relation between storage modulus and curing rate was established; the low curing rate of MDEN decreased the growth rate of storage modulus and reduced the internal stress, which was beneficial for processing. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40157.     

Effects of acid,alkaline, and seawater aging on the mechanical and thermomechanical properties of glass fiber/epoxy composites filled with carbon nanofibers

Owing to the superior corrosion resistance, fiber-reinforced polymer (FRP) composites are the prime choice of structural materials for various marine and chemical industries, where there is a long-term direct contact of the components takes place with corrosive fluids. In this present work, glass fiber/epoxy (GE) composites have been fabricated with and without carbon nanofibers (CNFs), and aging has been carried out in acidic (pH = 1), seawater (pH = 8.2), and alkaline (pH = 13) solutions for 150 days. The resistance of CNF-filled GE composites toward the corrosive fluids has been evaluated in terms of alteration in the mechanical (flexural), microstructural (fractography analysis by field emission scanning electron microscope), and thermomechanical (dynamic mechanical analysis) behavior of the materials. It is revealed that as the immersion time increases, there is a continuous decrement in flexural strength and modulus, and glass-transition temperature (T_g) of all the materials in all these solutions. Compared to the 1% CNF-filled GE composite, control GE composite showed more degradation in the case of alkaline aging and seawater aging. Maximum reduction (56%) in the strength of GE composite was observed due to 150 days of alkaline aging. However, the control GE composite showed better resistance to the acidic solution than that of CNF-filled GE composite. Possible failure modes, changes in the chemistry of the material due to aging have been studied by fractography analysis. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48434.     

Effects of aging and moisture on the dynamic viscoelastic properties of oriental lacquer (urushi) film

The effects of aging and moisture on the dynamic viscoelastic properties of three oriental lacquer films were investigated. With aging over 1000 days at room temperature, the glass‐transition temperature of the lacquer films (T_α) shifted to higher temperatures, the maximum loss tangent (tanδ_α) decreased, and the storage modulus at 20°C (E) increased. These changes were analogous irrespective of lacquers. With increasing moisture content, E decreased and tanδ increased at room temperature. Although the equilibrium moisture content of the virgin lacquer (sap) film was higher than that of the clear lacquer film, its E and tanδ were more stable with an increase of moisture content. It was speculated that the polysaccharides aggregated in the sap film did not effectively contribute to the mechanical properties of the film, while their hygroscopicity resulted in higher moisture content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2288–2294, 2002     

Effect of water sorption on the structure and mechanical properties of an epoxy resin system

The characteristics of sorption and diffusion of water in an amine‐cured epoxy system based on tetraglycidyl diaminodiphenylmethane and a novolac glycidyl ether resin were studied as a function both of the polymer microstructure, known from previous works, and the temperature. Water‐sorption experiments and dynamic mechanical analysis (DMA) were performed. Tensile stress–strain and Rockwell hardness tests were conducted to investigate the effects of absorbed water on the mechanical properties of the material. Competing effects of the sorption of water in the free volume and of strong interactions between water molecules and polar groups of the network were used to explain the diffusional behavior observed, which followed Fick's second law. DMA analysis seemed to be sensitive to the water effects and the viscoelastic behavior was related both to the water‐sorption processes and to the microstructure of the system. An important impact of water uptake on the tensile properties at break was also appreciated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 71–80, 2001     

Rheological behavior and mechanical properties of sawdust/polyethylene composites

We have characterized the melt rheological behavior and the solid tensile properties of sawdust/polyethylene composites prepared in an internal mixer. Various concentrations (from 0 to 60 wt %) and three particle sizes have been tested, in presence of a coupling agent (maleic anhydride grafted polyethylene). In the molten state, for each particle size, a mastercurve of the complex viscosity as function of frequency can be plotted, using a shift factor depending on weight fraction. We show that the shift factors can be described by a Krieger‐Dougherty law, leading to a “universal” viscosity law of the Carreau‐Yasuda type. In the solid state, the presence of sawdust increases Young modulus in uniaxial elongation, mainly for small size particles, but reduces dramatically deformation at break and tensile strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of cyclic compression and thermal aging on dynamic properties of neoprene rubber bearings

The dynamic properties of rubber bearings frequently used as isolators in structures could be significantly deteriorated because of the change of microstructure in rubber caused by cyclic compression and thermal aging. As a result, a catastrophic failure of bridges and buildings unexpectedly occurs when they are subjected to earthquake attack. Here, the dynamic properties of neoprene rubber bearings before and after different cycles of compressive loading or various periods of thermal aging were first measured and compared to each other. On the basis of the experimental results, the effects of cyclic compression and thermal aging on the stiffness, energy absorption, and equivalent viscous damping coefficient of neoprene rubber bearings are investigated. It is found that the deterioration of dynamic properties of neoprene rubber bearings caused by either cyclic compression or by thermal aging is significant and should be taken into account in designing rubber bearings. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

Modeling the evolution of the dynamic mechanical properties of a commercial epoxy during cure after gelation

The cure kinetics for a commercial epoxy have been established and the influence of the degree of cure on the glass transition determined. Time‐temperature and time‐conversion superposition principles have been built into a model that successfully predicts the development of the viscoelastic properties of the epoxy during isothermal cure from gelation to after vitrification. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 495–508, 2000     

Effects of composition of hardener on the curing and aging for an epoxy resin system

Different mixture ratios of Shell Epon 828 (based on diglycidyl ether of bisphenol A, DGEBA) and Shell EPI‐CURE 3046 (based on triethylenetetramine, TETA) were evaluated under different environments of isothermal curing at 80°C in DSC, room temperature curing in air, and aging in water at 45°C. The curing reactions were monitored using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and infrared spectroscopy (IR). It was shown that the initial curing rate increased with the amount of hardener. However, the epoxy groups in samples with excess hardener were prone to reaction with primary amines located at the ends of TETA molecules, resulting in a less dense epoxy network. During aging in water at 45°C, significant effects of water on the postcure and the increased water absorption with an increase of hardener amount were observed. The DMA results show that the samples with hardener around stoichiometric composition have the greatest storage modulus while curing in air environment. However, the samples with hardener much less than stoichiometric composition have greater storage modulus under aging in water at 45°C. in water at 45°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 580–588, 2006     

Effects of aging on the adhesive properties of poly(lactic acid) by atmospheric air plasma treatment

The aim of this study was to analyze the durability of a plasma treatment on the surface of poly(lactic acid) (PLA). We used atmospheric‐plasma treatment with air to improve the wettability of PLA by evaluating the aging effect under controlled conditions of relative humidity (RH) and temperature (25% RH and 25°C). We studied the durability of the atmospheric‐plasma treatment by measuring the contact angle, calculating the surface energy, and observing changes in the resistance of the PLA–PLA adhesive bonds. These techniques allowed us to evaluate the hydrophobic recovery phenomenon that the PLA surface suffered as a consequence of the aging process. The results provide the maximum storage time of PLA treated with atmospheric plasma at which the sample retained its good adhesion properties; this time was lower than 3 days under normal atmospheric conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43040.