Synergic effect of N‐benzylimine aminothioformamide secondary accelerator during sulfur vulcanization of a styrene‐butadiene‐natural rubber blend

In this study we reported synergic activity of a novel secondary accelerator N‐Benzylimine aminothioformamide (BIAT) along with tetramethylthiuram disulfide (TMTD) in improving cure and mechanical properties of gum and filled mixes of Styrene‐Butadiene Rubber (SBR). The feasibility of application of BIAT in sulfur vulcanization of an ideal blend of SBR and natural rubber (NR) has also been investigated. The mechanical properties like t ensile strength, tear resistance, hardness, compression set, and abrasion loss were measured. Swelling values were also determined as a measure of crosslink densities of the vulcanizates. The binary accelerator system BIAT‐TMTD was found very effective in improving cure properties of the mixes of pure SBR and a 50/50 blend of SBR and NR.There was also found simultaneous improvement in mechanical properties of vulcanizates of both pure and blend. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Bis(N‐benzyl piperazino) thiuram disulfide and dibenzothiazyl disulfide as synergistic safe accelerators in the vulcanization of natural rubber

Some investigation regarding the effect of binary system of accelerators comprising one safe thiuram disulfide, namely bis(N‐benzyl piperazino) thiuram disulfide (BPTD) and dibenzothiazyl disulfide (MBTS), on the vulcanization of NR is carried out. The results are compared with those obtained with conventional tetra methyl thiuram disulfide (TMTD) presently considered as unsafe. The vulcanizates obtained from safe synergistic pair of accelerators (BPTD‐MBTS) possess comparable mechanical properties [modulus, tensile strength, and elongation at break (%)] and exhibits some improvement in heat resistant behavior when compared with those obtained with TMTD‐MBTS system. In the light of mechanical properties, safe BPTD‐MBTS system introduces the safe noncarcinogenic rubber accelerator in the vulcanization of rubber. Same type of synergistic activity may be due to comparable activation energy for both the TDs with the combination of MBTS. Although rate constant values are low for BPTD‐MBTS (6 : 3) compared to TMTD‐MBTS (6 : 3) in the high temperature vulcanization, the crosslinking efficiency of former is very large compared to later. This may be responsible for improvement in heat resistance behavior of the novel accelerator in the combination with MBTS. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

New binary systems containing TMTD‐amidino phenyl thiourea and CBS–amidinophenyl thiourea for the vulcanization and rheological behavior of natural rubber latex

The use of accelerators in rubber latex is basically different from their use in dry rubber. In the present study, N amidino N'phenyl thiourea (APT) which is more nucleophilic than thiourea was studied as a secondary accelerator along with tetra methyl thiuram disulphide (TMTD) and N‐cyclohexylbenzothiazyl sulphenamide (CBS) in the vulcanization of natural rubber latex. These binary systems were found to be very effective in reducing the vulcanization time. The optimum dosages for this non‐toxic secondary accelerator required were derived. Rheological studies of the compounded latex show that the introduction of APT in these systems does not have adverse effect in processing in comparison with the thiourea systems. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies on novel binary accelerator system in sulfur vulcanization of natural rubber

The synergistic activity of binary accelerator systems in rubber vulcanization is well known. Binary accelerator systems are being widely used in industry and are becoming increasingly popular because of the fact that such mixed systems can effectively prevent prevulcanization, permit the vulcanization to be carried out at a lower temperature in a shorter time, and produce a vulcanizate with superior mechanical properties compared to those of a stock cured with a single accelerator. Thiourea and its derivatives are important secondary accelerators in this context. It is suggested that thiourea containing binary accelerator systems cause rubber vulcanization to proceed by a nucleophilic reaction mechanism. In the present study 1‐phenyl‐5‐ortho, ‐meta, and ‐para‐tolyl derivatives of 2,4‐dithiobiurets, which are more nucleophilic than thiourea and vary in their nucleophilic reactivity, are used as secondary accelerators along with 2‐morpholinothiobenzothiazole in the vulcanization of natural rubber. The results show an appreciable reduction in the cure time for the mixes containing the dithiobiurets compared to the reference mix. These results are indicative of a nucleophilic reaction mechanism in the vulcanization reaction under consideration. These vulcanizates also demonstrate comparatively better tensile properties and good retention of these properties after aging. An attempt is also made to correlate the variation in physical properties to chemical crosslink formation in the various vulcanizates. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3173–3182, 2003     

Optimization of accelerators on curing characteristics,tensile, and dynamic mechanical properties of (natural rubber)/(recycled ethylene‐propylene‐diene‐monomer) blends

The migration of sulfur from natural rubber (NR) compound to the ground waste ethylene‐propylene‐diene monomer (EPDM) rubber phase may have caused the cure incompatibility between these two rubbers. Optimization of accelerators had been adopted to overcome the cure incompatibility in NR/(R‐EPDM) blends as well as to get increased curative distribution. In this study, blends of NR and R‐EPDM were prepared. The effect of accelerator type on curing characteristics, tensile properties, and dynamic mechanical properties of 70/30/NR/(R‐EPDM) blend was investigated. Four types of commercial accelerators were selected [ie, N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , N‐cyclohexyl‐benzothiazyl‐sulfenamide (CBS), tetramethylthiuram disulfide, and 2‐mercaptobenzothiazol]. It was found that the tensile strength of the blends cured in the presence of CBS was relatively higher than the other three accelerators. Scanning electron micrographs of CBS‐cured NR/(R‐EPDM) blends exhibited more roughness and cracking path, indicating that higher energy was required toward the fractured surface. The high crosslinking density observed from the swelling method could be verified from the storage modulus (E′) and damping factor (tan δ) where (tetramethylthiuram disulfide)‐cured NR/(R‐EPDM) blends provided a predominant degree of crosslinking followed by N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , CBS, and 2‐mercaptobenzothiazol, respectively. J. VINYL ADDIT. TECHNOL., 21:79–88, 2015. © 2014 Society of Plastics Engineers     

Influence of sulfenamide accelerators on cure kinetics and properties of natural rubber foam

The effect of types of sulfenamide accelerator, i.e., 2‐morpholinothiobenzotiazole (MBS), N‐t‐butylbenzothiazole‐2‐sulfenamide (TBBS), and N‐cyclohexyl benzothiazole‐2‐sulfenamide (CBS) on the cure kinetics and properties of natural rubber foam was studied. It has been found that the natural rubber compound with CBS accelerator shows the fastest sulfur vulcanization rate and the lowest activation energy (E_a) because CBS accelerator produces higher level of basicity of amine species than other sulfenamide accelerators, further forming a complex structure with zinc ion as ligand in sulfur vulcanization. Because of the fastest cure rate of CBS accelerator, natural rubber foam with CBS accelerator shows the smallest bubble size and narrowest bubble size distribution. Moreover, it exhibits the lowest cell density, thermal conductivity and thermal expansion coefficient, as well as the highest compression set as a result of fast crosslink reaction. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44822.     

A new secondary accelerator for the sulfur vulcanization of natural rubber latex and its effect on the rheological properties

The vulcanization of natural rubber (NR) latex can be effectively carried out at low temperatures by using binary accelerator systems containing thiourea (TU) as a secondary accelerator. It was reported that sulfur‐containing nucleophiles such as thiourea enable the primary accelerator to become effective even at low temperatures, indicating a nucleophilic reaction mechanism in such vulcanization reactions. In the present study, a derivative of thiourea [viz. aminoiminomethyl thiourea (AMT)], which is more nucleophilic than thiourea, is used as a secondary accelerator in the sulfur vulcanization of NR latex. One of the aims of this study was to give conclusive evidence for a nucleophilic reaction mechanism. The synergistic effect of the above thiourea derivative with primary accelerators such as tetramethylthiuram disulfide (TMTD), zinc diethyldithiocarbamate (ZDC), and cyclohexylbenzthiazyl sulfenamide (CBS) was studied at two different temperatures (viz. 100 and 120°C). These binary systems were found to be very effective in reducing the optimum cure time of the different mixes compared to control formulations containing TU. The optimum amount of the secondary accelerator required was also determined. Mechanical properties such as tensile strength and tear strength of the vulcanizates were also evaluated. Chemical characterization of the vulcanizates was carried out by determining the total crosslink density. Values of the cure characteristics evaluated support a nucleophilic reaction mechanism in these vulcanization reactions under review. The effect of this secondary accelerator on the rheological behavior of compounded latex is also studied and was found not to affect adversely. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2781–2789, 2004     

Synthesis,characterization, and evaluation of natural rubber‐graft‐N‐(4‐aminodiphenyl methane) acrylamide as an antioxidant

The synthesis of N‐(4‐aminodiphenylmethane) acrylamide (ADPMA) was performed through the reaction of 4,4′‐diaminodiphenyl methane and acryloyl chloride in the presence of triethyl amine. The grafting of ADPMA onto natural rubber was executed with UV radiation. Benzoyl peroxide was used to initiate the free‐radical grafting copolymerization. Natural rubber‐graft‐N‐(4‐aminodiphenyl methane) acrylamide (NR‐g‐ADPMA) was characterized with an IR technique. We studied the effect of aging on the mechanical properties and the swelling and extraction phenomena for acrylonitrile–butadiene copolymer (NBR) vulcanizates, which contained the prepared NR‐g‐ADPMA and a commercial antioxidant, N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine. The prepared antioxidant enhanced both the mechanical properties of the NBR vulcanizates and the permanence of the ingredients in these vulcanizates. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 843–849, 2006     

TDEC和ZDC对EPDM的硫化促进性能的影响

促进剂在橡胶硫化中起着非常重要的作用,其中氨基甲酸盐类作为超促进剂的一种,在工业生产中有着广泛的用途,特别适用于丁基橡胶和三元乙丙橡胶。目前氨基甲酸盐类促进剂还没有较好的替代品。研究了氨基甲酸盐类中的TDEC和ZDC两种促进剂对三元乙丙胶的硫化促进性能。研究发现,TDEC的硫化促进性能和硫化胶的力学性能远好于ZDC。TDEC和ZDC的加入远好于空白样,说明氨基甲酸盐类促进剂有效地促进了硫化,并改善了硫化胶的力学性能。     

Upgrading of acrylonitrile–butadiene copolymer properties using natural rubber–graft–N‐(4‐aminodiphenylether) acrylamide

The grafting of ADPEA onto natural rubber was executed with UV radiation. Benzoyl peroxide was used to initiate the free‐radical grafting copolymerization. Natural rubber‐graft‐N‐(4‐aminodiphenylether) acrylamide (NR‐g‐ADPEA) was characterized with an IR technique. The ultrasonic velocities of both longitudinal and shear waves were measured in thermoplastic discs of NBR vulcanizates as a function of aging time. Ultrasonic velocity measurements were taken at 2 MHz ultrasonic frequency using the pulse echo method. We studied the effect of aging on the mechanical properties and the swelling and extraction phenomena for acrylonitrile–butadiene copolymer (NBR) vulcanizates, which contained the prepared NR‐g‐ADPEA and a commercial antioxidant, N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine. The prepared antioxidant enhanced both the mechanical properties of the NBR vulcanizates and the permanence of the ingredients in these vulcanizates. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies on ethylene‐propylene‐diene rubber modification by N‐chlorothio‐N‐butyl‐benzenesulfonamide

N‐Chlorothiosulfonamides have been used to modify ethylene‐propylene‐diene rubber (EPDM) to enhance the compatibility of EPDM in, e.g., natural rubber (NR)/butadiene rubber (BR)/EPDM blends for ozone resistance. N‐Chlorothio‐N‐butyl‐benzenesulfonamide (CTBBS) was selected as a representative for N‐chlorothiosulfonamides. In this study, we found that CTBBS behaves differently with various types of EPDM. Three types of EPDM were selected: ethylidene norbornene (ENB)‐EPDM, hexadiene (HD)‐EPDM, and dicyclopentadiene (DCPD)‐EPDM. HD‐EPDM showed the greatest effectiveness toward CTBBS‐modification. However, this EPDM is not commercially available anymore. On the opposite side, DCPD‐EPDM showed the lowest reactivity so that almost no modification could be realized. The result with ENB‐EPDM was, that upon application of CTBBS to ENB‐EPDM, gelation occurred and, therefore, a low amount of modification was achieved. With the limited modification efficiency for ENB‐EPDM, there is no significant improvement when applying the modified ENB‐EPDM into NR/BR/EPDM blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of fillers in the binary systems containing TMTD–amidinothiourea and MBTS–amidinothiourea in NR vulcanization

In earlier studies,^1,2 we have shown that in MBTS–amidinothiourea and TMTD–amidinothiourea binary system of rubber vulcanization, amidinothiourea functions effectively as a secondary accelerator and improves the accelerator activity of these systems. These secondary accelerators enhance the physical properties of the vulcanizates and show better cure characteristics of the mixes compared to the reference systems studied. In this paper, we present the results of our study on the effect of various fillers in the sulfur vulcanization of natural rubber using amidinothiourea as the secondary accelerator. We have taken MBTS–amidinothiourea and TMTD–amidinothiourea binary accelerator systems and vulcanizates were prepared with carbon black, precipitated silica, and china clay as fillers. Different compositions of amidinothiourea were used in various mixes using standard recipes. Reference mixes were also studied. Curing characteristics of the mixes and various physical properties of the vulcanizates were evaluated. Optimum dosage of amidinothiourea required has also been derived. Among the different secondary accelerators tried including amidinothiourea, it may be stated generally that the more nucleophilic the secondary accelerator, the less the optimum cure times. This fact points to a nucleophilic reaction mechanism in the systems under review. In the evaluation of tensile and other physical properties of the vulcanizates, some of the systems containing amidinothiourea show better properties while others give comparable values with the reference mixes. Estimation of crosslink density also supports the above conclusion. © 1996 John Wiley & Sons, Inc.     

Studies on cure synergism. I. Effect of safe zinc dithiocarbamates on NR vulcanization accelerated by thiazole-based accelerators

Investigations have been carried out on the effect of several zinc dithiocarbamates in the presence of thiazole-based accelerators in the vulcanization of natural rubber (NR), keeping in mind the possibility of introducing safe dithiocarbamates derived from safe amines. Mutual activity is observed in all the binary systems studied, the highest being observed in the zinc dibenzyldithiocarbamate-dibenzothiazyldisulfide (ZBEC–MBTS)-accelerated system. The effect of zinc diisopropyl dithiophosphate, reportedly a safe rubber additive, which is recognized as an age-resistant agent for NR, on cure has also been studied. The study reveals that thiuram disulfide and MBT are always formed from the reaction either between zinc dithiocarbamate (ZDC) and MBTS or between ZDC and N-cyclohexyl-2-benzothiazole sulfenamide (CBS). It has been conclusively proved that 2-mercaptobenzothiazole (MBT) generated from MBTS or CBS reacts with ZDC and produces tetramethyl thinram disulfide (TMTD). The observed mutual activity has been discussed based on the cure and physical data and explained through the results based on HPLC and a reaction mechanism. © 1994 John Wiley & Sons, Inc.     

Safe amine based zinc dithiocarbamates for the vulcanization of carbon black reinforced natural rubber

Binary combination of three safe amine based synthesized zinc dithiocarbamates (ZDC), namely zinc (N‐benzyl piperazino) dithiocarbamate (ZBPDC), zinc (N‐ethyl piperazino) dithiocarbamate (ZEPDC), and zinc (N‐phenyl piperazino) dithiocarbamate (ZPPDC) with mercapto benzothiazole disulfide (MBTS) as an effective accelerator system for the vulcanization of carbon black (N330, N550, and N774) filled natural rubber (NR) composites are studied. A comparison between the safe amine based zinc dithiocarbamates with the unsafe zinc dimethyl dithiocarbamate (ZDMC) in the light of mechanical and aging resistance behavior, introduces the non carcinogenic rubber additives in the filled vulcanization of rubber. Both accelerator and filler have the major importance for improving the mechanical as well as aging resistance behavior of the resultant vulcanizate. Variation in the filler and also filler to oil ratio are done to optimize the mechanical properties. SEM studies of different types of filler with different amounts show that N330 at 30 phr loading composites forms more homogeneity and less aggregated structures. Natural rubber systems with N330 carbon black show the best results with respect to tensile strength, but after the aging N774 carbon black filled system indicates better retention in the tensile strength. ZPPDC‐MBTS accelerated vulcanizate shows the better age resistance behavior than ZDMC‐MBTS accelerated vulcanizate. From both the points of age resistance and mechanical properties, ZBPDC‐MBTS accelerator system is the suitable substitute for ZDMC‐MBTS accelerated system in the filled vulcanization of natural rubber composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39988.     

Effect of N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine antioxidant on the adhesion properties of (zinc oxide)‐filled (epoxidized natural rubber 25)‐based pressure‐sensitive adhesives

The effect of antioxidant, namely, N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine (IPPD), on the adhesion properties of epoxidized natural rubber (ENR 25)‐based pressure‐sensitive adhesive was investigated. The concentration of the IPPD was varied from 0 to 5 parts by weight per hundred parts of rubber (phr). Coumarone‐indene resin, zinc oxide, toluene, and polyethylene terephthalate were used as the tackifier, filler, solvent, and substrate, respectively. A Lloyd Adhesion Tester operating at different testing rates (10–60 cm/min) was used to determine the loop tack, peel strength, and shear strength at 60‐µm and 120‐µm coating thicknesses. Results indicate that adhesion properties increase with IPPD up to 2 phr of content, after which it decreases with further addition of the antioxidant. This observation is attributed to the culmination of wettability and compatibility at the optimum IPPD concentration. The 60‐µm coated sample consistently shows higher adhesion strength than that of 120‐µm coated sample. Loop tack and peel strength increase with testing rate up to 30 cm/min. However, shear strength increases with increasing testing rate in the testing rate investigated in this study. J. VINYL ADDIT. TECHNOL., 21:111–115, 2015. © 2014 Society of Plastics Engineers     

Rheological and mechanical properties of DGEBA‐S epoxy copolymer initiated by N‐benzylquinoxalinium hexafluoroantimonate

The rheological and mechanical properties of the DGEBA‐S epoxy copolymer initiated by N‐benzylquinoxalinium hexafluoroantimonate (BQH) as a cationic latent thermal catalyst were investigated. The rheological properties of the DGEBA‐S/BQH system were investigated using a rheometer under isothermal conditions, and the mechanical properties of the casting specimens, involving flexure and impact tests, were also performed. The crosslinking activation energy and mechanical properties of the DGEBA‐S/BQH system were higher than those of the DGEBA/BQH system. This could be attributed to the introduction of sulfone groups with a polar nature to the main chain of the epoxy resins which led to a decrease of molecular motion and an improvement in the toughness of the cured epoxy copolymers. Copyright © 2005 Society of Chemical Industry     

Blend films of O‐carboxymethyl chitosan and cellulose in N‐methylmorpholine‐N‐oxide monohydrate

To introduce N‐methylmorpholine‐N‐oxide (NMMO) process to prepare antibacterial lyocell fiber, the blend films of O‐carboxymethyl chitosan (O‐CMCS) and cellulose were prepared. O‐CMCS in aqueous suspension with particles having a surface mean diameter of 2.24 μm was blended with cellulose in NMMO hydrate. The blend films with different O‐CMCS content were prepared with the blend solutions. SEM confirmed that O‐CMCS remained within the cellulose film in the particle. The mechanical properties of the blend films show little increased value when O‐CMCS was less 5%; however, it decreased sharply when O‐CMCS was over 8%. Thus, the optimum O‐CMCS content may give a good combination of antibacterial action and mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4601–4605, 2006     

A new binary accelerator system for the sulfur vulcanization of natural rubber latex

Vulcanization of latex products are usually carried out at lower temperatures compared to dry rubber products. It has been suggested that, in latex vulcanization systems where thiourea is used as a secondary accelerator, it acts as a nucleophilic reagent facilitating the cleavage of the sulfur bonds in the primary accelerator like TMTD or CBS at lower temperature. But no conclusive proof is given to such a postulate. In the present study 1-phenyl-2,4-thiobiuret (DTB II) and 1,5-diphenyl-2,4-dithiobiuret (DTB III), which are more nucleophilic than thiourea and which vary in their nucleophilic reactivity, were studied as secondary accelerators along with tetramethyl thiuram disulphide (TMTD) and N-cyclohexylbenzothiazyl sulphenamide (CBS) in the vulcanization of natural rubber latex. These binary systems were found to be very effective in reducing the optimum vulcanization time. Also it was noted that 1-phenyl-2,4-dithiobiuret, which is more nucleophilic, is more reactive (as observed from the reduction in optimum cure time) as a secondary accelerator, indicating a nucleophilic reaction mechanism in the vulcanization reactions under review. The optimum dosages of the secondary accelerators required were derived. Physical properties like tensile strength, 300% modulus, and elongation at break of the latex vulcanizates were also studied. There is a definite advantage with respect to many of these properties for dithiobiuret systems compared to the systems containing TMTD alone or TMTD/thiourea. DTB III gives higher values in many of these physical properties than DTB II. Chemical characterization of the vulcanizates was also carried out to correlate the physical properties with the type of chemical crosslinks formed. © 1993 John Wiley & Sons, Inc.     

Epoxidized natural rubber as a reinforcement modifier for silica‐filled nitrile rubber

Hydrated silicas impart better physical properties to polar rubbers, compared to those of hydrocarbon rubbers. However, to achieve optimum properties silane coupling agents are crucial in such formulations. Epoxidized natural rubber (ENR) in small proportions is used as a reinforcement modifier for silica‐filled nitrile rubber (NBR). Two systems of cure were used: N‐cyclohexyl‐ 2‐benzthiazyl sulfenamide (CBS) alone and in combination with diphenyl guanidine (DPG). In the CBS accelerated system, incorporation of an optimum concentration of about 15% of ENR on total rubber was found to improve technological properties. Addition of a secondary accelerator further improves these properties. Comparable results are obtained with those containing coupling agent and NBR–ISAF. High bound rubber and volume fraction values indicate a high polymer–filler interaction and gel content resulting from the NBR–ENR interaction. Results of this study reveal that ENR could be used as a reinforcement modifier for the NBR–silica system. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 292–306, 2002     

Studies on novel binary accelerator system in sulfur vulcanization of natural rubber

The synergistic activity of binary accelerator systems in rubber vulcanization is well known. Thiourea and its derivatives are important secondary accelerators in this context. It is suggested that thiourea containing binary systems of rubber vulcanization proceed by a nucleophilic reaction mechanism. Amidinothioureas (ATUs), which are derivatives of thiourea, have been investigated extensively as secondary accelerators. One of the aims of this study was to get further proof with regard to the theory of the nucleophilic reaction mechanism in such binary systems. In the present study phenyl substituted ATU was used as a secondary accelerator along with mercaptobenzothizyl disulfide, tetramethyl thiuram disulfide, or cyclohexyl benzthiazyl sulfenamide in the sulfur vulcanization of natural rubber. The results showed an appreciable reduction in the cure time for the mixes containing the ATU compared to the reference mixes. These results are indicative of a nucleophilic reaction mechanism in the vulcanization reaction under review. These vulcanizates also showed comparatively better tensile properties and good retention of these properties after aging. The optimum dosages of the secondary accelerator required for these vulcanization reactions were also derived. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1–8, 2001