The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Influence of organically modified nanoclay on the performance of pineapple leaf fiber‐reinforced polypropylene nanocomposites

Polypropylene/Pine apple leaf fiber (PP/PALF)‐reinforced nanocomposites were fabricated using melt blending technique in a twin‐screw extruder (Haake Rheocord 9000). Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of nanoclay in PP/PALF composites were investigated. It was observed that the tensile, flexural, and impact properties of PP increase with the increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % PALF and 5 wt % MA‐g‐PP exhibited optimum mechanical performance with an increase in tensile strength to 31%, flexural strength to 45% when compared with virgin PP. Addition of nanoclay results in a further increase in tensile and flexural strength of PP/PALF composites to 20 and 24.3%, which shows intercalated morphology. However, addition of nanoclay does not show any substantial increase in impact strength when compared with PP/PALF composites. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), confirming a strong influence between the fiber/nanoclay and MA‐g‐PP. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties when compared with the virgin matrix. TEM micrographs also showed few layers of agglomerated clay galleries along with mixed nanomorphology in the nanocomposites. Wide angle X‐ray diffraction studies indicated an increase in d‐spacing from 22.4 Å in Cloisite 20A to 40.1 Å in PP/PALF nanocomposite because of improved intercalated morphology. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Melt grafting of maleic anhydride onto polypropylene with assistance of α‐methylstyrene

Melt grafting of maleic anhydride (MA) and α‐methylstyrene (AMS) onto polypropylene (PP) was performed by reactive extrusion. Effects of AMS on the graft degree of MA, crystallization behavior, and thermal properties of the graft copolymer were investigated. Results show that the addition of AMS as a comonomer can efficiently improve the MA graft degree. When the molar ratio of AMS to MA is 0.9:1, the maximum MA graft degree is attained, which increases about 56% compared with that using single monomer of MA. The results of the graft degree of MA obtained by chemical titration (CT) agree well with those obtained by Fourier transform infrared spectroscopy (FTIR). Melt flow rate (MFR) measurements indicate that the addition of AMS effectively reduces the degradation of PP molecules. The wide‐angle X‐ray diffraction (WAXD) results show that in comparison with the PP‐g‐MA sample, the PP‐g‐(MA‐AMS) sample shows no new crystalline form, but has a slight decrease in the average crystalline domain size. According to the results of thermogravimetry (TG) and differential scanning calorimetry (DSC), the graft PP in the presence of AMS exhibits a lower melting point and a higher crystallization temperature and thermal stability in comparison with that without AMS. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphological structure and surface properties of maleated ethylene propylene diene monomer/organoclay nanocomposites

The phase morphology and surface properties of some maleated ethylene propylene‐diene/organoclay nanocomposites (EPDM‐g‐MA/OC) were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and contact angle measurements. The effect of organoclay and/or compatibilizing agent [maleic anhydride‐grafted polypropylene (PP‐g‐MA)] on the properties of the EPDM‐g‐MA nanocomposites was investigated. The quality and uniformity of nanoclay dispersion were analyzed by SEM and AFM images. The experimental results showed an intercalate structure and biphasic morphology for the binary blends based on EPDM and clay. The surface properties of the studied composites are significantly influenced by the presence of a compatibilizing agent—PP‐g‐MA. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Interfacial agent effect on rheological response and crystallite characteristics in germicidal polypropylene/titanium dioxide nanocomposites

Germicidal nanocomposites based on metallocene isotactic polypropylene (iPP) and titanium dioxide (TiO₂) nanoparticles have been prepared at a constant TiO₂ content of 2 wt%. Different quantities of a polypropylene wax partially grafted with maleic anhydride (PP‐g‐MAH) are employed to improve the polymer‐nanoparticle compatibility. Remarkable biocidal capabilities of these TiO₂ nanocomposites have been found and their crystalline structure and thermal and rheological responses explored. Several very interesting features have been found in these germicidal nanocomposites. On the one hand, rheological parameters do not change significantly with respect to those exhibited by pure iPP. This is extremely advantageous for the processing of these compounds since they can be transformed under similar conditions to those employed for iPP. On the other hand, the existence of two polymorphs is observed independent of the amount of compatibilizer used. The enhancement in polymer‐nanoparticle interactions by effect of the interfacial (PP‐g‐MAH) component is appraised looking at dynamical mechanical relaxations as a function of temperature and at crystallization processes of the various nanocomposites. Copyright © 2012 Society of Chemical Industry     

Mechanical and thermal properties of polypropylene nanocomposites using organically modified Indian bentonite

We report preparation and characterization of nanoclay from Indian bentonite and imported nanoclays, and their compounding with polypropylene (PP) and maleic anhydride‐grafted PP (MA‐g‐PP) in twin screw extruder. The compounded polymer/nanoclay nanocomposites (PNCs) are molded into a standard specimen for studying its tensile, flexural and impact strength. A wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) study demonstrates intercalation of PP in nanoclays rather than exfoliation for both, indigenous and imported nanoclays. The tensile modulus increased by 41 and 39% for PNC1 (PNC with imported nanoclay) and PNC2 (PNC with indigenous nanoclay) with respect to PP. The flexural modulus for PNC1 and PNC2 also increases by 23 and 22% due to incorporation of 5% nanoclay in PP along with 5% MA‐g‐PP. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Polypropylene/clay nanocomposites: An innovative one‐pot process

This work discloses a novel one‐pot preparation method of polypropylene (PP)/clay nanocomposites with high degree of clay delamination and improved thermal, mechanical and rheological properties. The in situ simultaneous synthesis of carboxylate clay from native clay and ionomer of PP‐graft maleic anhydride (PP‐g‐MA) through trihydrate sodium acetate addition, combined with water injection in the extrusion process, appears to be a valuable alternative to the use of organoclay for producing PP/PP‐g‐MA/clay nanocomposites. The influence of PP‐g‐MA graft content, and of its ionomer form, onto the clay dispersion has been especially investigated. PP‐g‐MA of low graft content is compared to a home‐made highly grafted PP‐g‐MA synthesized in the presence of N‐bromosuccinimide (NBS). The nanocomposites prepared by combining the use of NBS‐mediated PP‐g‐MA, trihydrate sodium acetate and water injection exhibit the highest clay dispersion. Thermal, rheological, and mechanical properties of the nanocomposites have been measured. POLYM. COMPOS., 36:644–650, 2015. © 2014 Society of Plastics Engineers     

Crystallization,mechanical, and fracture behavior of mullite fiber‐reinforced polypropylene nanocomposites

This study describes the reinforcement effect of surface modified mullite fibers on the crystallization, thermal stability, and mechanical properties of polypropylene (PP). The nanocomposites were developed using polypropylene‐grafted‐maleic anhydride (PP‐g‐MA) as compatibilizer with different weight ratios (0.5, 1.0, 1.5, 2.5, 5.0, and 10.0 wt %) of amine functionalized mullite fibers (AMUF) via solution blending method. Chemical grafting of AMUF with PP‐g‐MA resulted in enhanced filler dispersion in the polymer as well as effective filler‐polymer interactions. The dispersion of nanofiller in the polymer matrix was identified using scanning electron microscopy (SEM) elemental mapping and transmission electron microscopy (TEM) analysis. AMUF increased the Young's modulus of PP in the nanocomposites up to a 5 wt % filler content, however, at 10 wt % loading, a decrease in the modulus resulted due to agglomeration of AMUF. The impact strength of PP increased simultaneously with the modulus as a function of AMUF content (up to 5 wt %). The mechanical properties of PP‐AMUF nanocomposites exhibited improved thermal performance as compared to pure PP matrix, thus, confirming the overall potential of the generated composites for a variety of structural applications. The mechanical properties of 5 wt % of AMUF filled PP nanocomposite were also compared with PP nanocomposites generated with unmodified MUF and the results confirmed superior mechanical properties on incorporation of modified filler. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43725.     

Nanocomposites of syndiotactic polypropylene: Phase behavior and morphology

Through differential scanning calorimetry, the crystallization kinetics of syndiotactic polypropylene (sPP) nanocomposites with organically modified layered silicates has been investigated in both nonisothermal and isothermal conditions. A strong influence on the thermal behavior is exerted by the compatibilizer agent (low molecular weight isotactic polypropylene‐g‐maleic anydrhyde, iPP‐g‐MA), which increases the crystallization rate of sPP. A further strong increase in the crystallization rate is observed upon increasing the OLS content in the sample. The kinetics data have been analyzed through the Ozawa, Avrami, and Tobin methods, the first of them resulted ineffective in describing our data. Morphological analyses have been performed by polarized optical microscopy and atomic force microscopy. Spherulitic morphology is observed for neat sPP; for the sample containing only the compatibilizer the spherulites grow around the iPP‐g‐MA particles, revealing their nucleating effect on sPP crystallization; for the nanocomposites the spherulitic morphology is lost: the texture appears globular, compact; inside the globules lamellae are present, parallel one to the other. POLYM. ENG. SCI., 46:1433–1442, 2006. © 2006 Society of Plastics Engineers     

Effects of melt structure on crystallization behavior of isotactic polypropylene nucleated with α/β compounded nucleating agents

In this study, the melt structure of isotactic polypropylene (iPP) nucleated with α/β compounded nucleating agents (α/β‐CNA, composed of the α‐NA of 0.15 wt % Millad 3988 and the β‐NA of 0.05 wt % WBG‐II) was tuned by changing the fusion temperature T_f. In this way, the role of melt structure on the crystallization behavior and polymorphic composition of iPP were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray scattering (WAXD) and scanning electron microscopy (SEM). The results showed that when T_f = 200°C (iPP was fully molten), the α/β‐CNA cannot encourage β‐phase crystallization since the nucleation efficiency (NE) of the α‐NA 3988 was obviously higher than that of the β‐NA WBG‐II. Surprisingly, when T_f was in 179–167°C, an amount of ordered structures survived in the melt, resulting in significant increase of the proportion of β‐phase (achieving 74.9% at maximum), indicating that the ordered structures of iPP played determining role in β‐phase crystallization of iPP nucleated with the α/β‐CNA. Further investigation on iPP respectively nucleated with individual 3988 and WBG‐II showed that as T_f decreased from 200°C to 167°C, the crystallization peak temperature T_c of iPP/3988 stayed almost constant, while T_c of iPP/WBG‐II increased gradually when T_f < 189°C and became higher than that of iPP/3988 when T_f decreased to 179°C and lower, which can be used to explain the influence of ordered structure and α/β‐CNA on iPP crystallization. Using this method, the selection of α‐NA for α/β‐CNA can be greatly expanded even if the inherent NE of β‐NA is lower than that of the α‐NA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41355.     

Melt processing and characterization of multicomponent polymeric nanocomposites containing organoclay

Nylon 6 (Ny)/polypropylene (PP)/maleated polypropylene (PP‐g‐MA)/organoclay/wollastonite composites were prepared by melt processing. The polymers' composition was kept constant ([70PP/30Ny]/4PP‐g‐MA). Melt compounding was conducted using a twin‐screw extruder in three different methods: (1) simultaneous incorporation of the components into the compounding equipment, (2) preparation of [Ny6/clay] concentrate, and then in a second step, mixing the other components with the concentrate, and (3) mixing of PP with wollastonite and clay followed by the addition of Ny6 and PP‐g‐MA in the second step. Injection‐molded specimens were characterized in tension, scanning electron microscopy, X‐ray diffraction (XRD), and differential scanning calorimetry. The sequence of component addition greatly influences the structure and properties of the composites. Enhanced mechanical properties were achieved when the two‐step mixing procedure was used for the PP/Ny6/PP‐g‐MA/clay system (method 2) and also for the PP/Ny6/PP‐g‐MA/clay/wollastonite system (method 3). The XRD pattern of the PP/Ny6/PP‐g‐MA/clay nanocomposites produced by the two‐step mixing method does not show a characteristic basal reflection of the pristine organoclay, indicating a predominately exfoliated structure of clay. POLYM. COMPOS., 28:417–424, 2007. © 2007 Society of Plastics Engineers     

Polymer nanocomposites based on needle‐like sepiolite clays: Effect of functionalized polymers on the dispersion of nanofiller,crystallinity, and mechanical properties

Polypropylene (PP)/sepiolite (Sep) nanocomposites are prepared by melt compounding in a mini‐extruder apparatus. The often used maleic anhydride‐modified polypropylene (PP‐g‐MA) is compared with two custom‐made functionalized polymers, PP‐acid and the di‐block copolymer PP‐PEO, with respect to the filler dispersion and filler reinforcement efficiency. For that purpose, morphological and mechanical studies are carried out by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), and mechanical tensile tests. In addition, the nanocomposites are characterized by wide‐angle X‐ray scattering (WAXS) and differential scanning calorimetric (DSC) techniques, to assess the effect of the nanofiller on the crystalline structure of the PP matrix nano‐filler. The use of PP‐PEO and PP‐acid resulted in a better nanofiller dispersion compared with traditional PP‐g‐MA‐modified systems. Sepiolite acts as nucleating agent for the crystallization of PP and seems to lead to an orientation of the α‐phase crystals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Effects of different compatibilizers on the rheological,thermomechanical, and morphological properties of HDPE/LLDPE blend‐based nanocomposites

The influence of two different compatibilizers and their combination (maleic anhydride grafted high density polyethylene, HDPE‐g‐MA; maleic anhydride grafted linear low density polyethylene, LLDPE‐g‐MA; and 50/50 wt % mixture of these compatibilizers) on the rheological, thermomechanical, and morphological properties of HDPE/LLDPE/organoclay blend‐based nanocomposites was evaluated. Nanocomposites were obtained by melt‐intercalation in a torque rheometer in two steps. Masterbatches (compatibilizer/nanoclay 2:1) were obtained and subsequently diluted in the HDPE/LLDPE matrix producing nanocomposites with 2.5 wt % of nanoclay. Wide angle X‐ray diffraction (WAXD), steady‐state rheological properties, and transmission electron microscopy (TEM) were used to determine the influence of different compatibilizer systems on intercalation and/or exfoliation process which occurs preferentially in the amorphous phase, and thermomechanical properties. The LLDPE‐g‐MA with a high melt index (and consequently low viscosity and crystallinity) was an effective compatibilizer for this system. Furthermore, the compatibilized nanocomposites with LLDPE‐g‐MA or mixture of HDPE‐g‐MA and LLDPE‐g‐MA exhibited better nanoclay's dispersion and distribution with stronger interactions between the matrix and the nanoclay. These results indicated that the addition of maleic anhydride grafted polyethylene facilitates both, the exfoliation and/or intercalation of the clays and its adhesion to HDPE/LLDPE blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1726–1735, 2013     

Effects of carbon nanofibers on the fracture,mechanical, and thermal properties of PP/SEBS‐g‐MA blends

Polypropylene/maleated (styrene‐ethylene‐butadiene‐styrene) (PP/SEBS‐g‐MA) blends reinforced with 0.2–2.5 wt% carbon nanofibers (CNFs) were prepared by injection molding. The structure, thermal, mechanical, and fracture behaviors of PP/SEBS‐g‐MA blends and their nanocomposites were studied. Wide‐angle X‐ray diffraction (WAXD) results showed that the SEBS‐g‐MA and/or CNF additions do not induce a structural change of PP. Tensile measurements showed that the Young's modulus and tensile yield strength increase with the increasing filler content. Izod impact and essential work of fracture test results demonstrated that CNFs are beneficial to improve the impact strength and specific essential work of fracture of PP/SEBS‐g‐MA blends. Therefore, tough PP‐nanocomposites can be achieved by melt‐blending low fractions of CNFs and appropriate elastomer contents. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Isotactic polypropylene toughened with poly(acrylonitrile–butadiene–styrene): Compatibilizing role of maleic anhydride grafted polypropylene

The β‐nucleating activity and toughening effect of acrylonitrile–butadiene–styrene (ABS) graft copolymer on isotactic polypropylene (iPP) and the compatibilizing role of maleic anhydride grafted polypropylene (PP‐g‐MAH) on the iPP/ABS blends were investigated. The results show that ABS can induce the formation of β‐crystal in iPP, and its β‐nucleating efficiency depends on its concentration and dispersibility. The relative content of β‐crystal form is up to 36.19% with the addition of 2% ABS. The tensile and impact properties of the iPP were dramatically enhanced by introducing ABS. The incorporation of PP‐g‐MAH into the iPP/ABS blends inhibits the formation of β‐crystal. The crystallization peaks of the blends shift toward higher temperature, due to the heterogeneous nucleation effect of PP‐g‐MAH on iPP. The toughness of iPP/ABS blends improved due to favorable interfacial interaction resulting from the compatibilization of PP‐g‐MAH is significantly better than the β‐crystal toughening effect induced by ABS. POLYM. ENG. SCI., 59:E317–E326, 2019. © 2019 Society of Plastics Engineers     

Effect of the molecular weight of maleated polypropylenes on the melt compounding of polypropylene/organoclay nanocomposites

Maleic anhydride grafted polypropylene (PP‐g‐MA) and organically modified clay composites were prepared in a plasticorder. PP‐g‐MAs, including Polybond PB3150, Polybond PB3200, Polybond PB3000, and Epolene E43, with a wide range of maleic anhydride (MA) concentrations and molecular weights were used. The structure was investigated with X‐ray diffraction (XRD) and transmission electron microscopy (TEM). PP‐g‐MA compatibilizers gave rise to similar degrees of dispersion beyond the weight ratio of 3/1, with the exception of E43, which had the highest MA content and the lowest molecular weight. The thermal instability and high melt index were responsible for the ineffective modification by E43. Furthermore, PP‐g‐MA with a lower molecular weight and a higher melt index had to be compounded at a lower mixing temperature to achieve a reasonable level of torque for clay dispersion. Polypropylene/organoclay nanocomposites were then modified with different levels of PP‐g‐MA compatibilizers with a twin‐screw extruder. The polypropylene/E43/clay system, as shown by XRD patterns and TEM observations, yielded the poorest clay dispersion of the compatibilizers under investigation. The curves of the relative complex viscosity also revealed a systematic trend with the extent of exfoliation and showed promise for quantifying the hybrid structure of the nanocomposites. The mechanical properties and thermal stability were determined by dynamical mechanical analysis and thermogravimetric analysis, respectively. Although PP‐g‐MA with a lower molecular weight led to better clay dispersion in the polypropylene nanocomposites, it caused deterioration in both the mechanical and thermal properties of the hybrid systems. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1667–1680, 2005     

A comparative study of polypropylene nucleated by individual and compounding nucleating agents. I. Melting and isothermal crystallization

In this study, melting and isothermal crystallization behaviors of polypropylene (PP) nucleated with different nucleating agents (NAs) have been comparatively studied. α‐phase NA 1,3 : 2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase NA aryl amides compound (TMB‐5), and their compounds were introduced into PP matrix, respectively. The crystallization and melting characteristics as well as the crystallization structures and morphologies of nucleated PP were studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). As indicated by previous work that a few amounts of α‐phase NA (DMDBS) or β‐phase NA (TMB‐5) has apparent nucleation effect for PP crystallization. However, the crystallization of PP nucleated with compounding NAs is dependent on the content of each NA. In the sample of PP with 0.1 wt % DMDBS and 0.1 wt % TMB‐5, the nucleation efficiency of TMB‐5 is much higher than that of DMDBS and PP crystallization is mainly nucleated by TMB‐5, and in this condition, β‐phase PP is the main crystallization structure. For the sample of PP with 0.2 wt % DMDBS and 0.2 wt % TMB‐5, 0.2 wt % DMDBS has higher nucleation efficiency than 0.2 wt % TMB5, and α‐phase is the main crystalline structure in this sample. The isothermal crystallization kinetics and crystallization structure have been analyzed in detail in this work. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009