Preparation and structure and mechanical properties of poly(styrene‐b‐butadiene)/clay nanocomposites

Star‐shaped and linear block thermoplastic poly(styrene‐b‐butadiene) copolymer (SBS)/organophilic montmorillonite clays (OMMT) were prepared by a solution approach. The intercalation spacing in the nanocomposites and the degree of dispersion of nanocomposites were investigated by X‐ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The mechanical properties, dynamic mechanical properties, and thermal stability of these nanocomposites were determined. Results showed that SBS chains were well intercalated into the clay galleries and an intercalated nanocomposite was obtained. The mechanical strength of nanocomposites with the star‐shaped SBS/OMMT were significantly increased. The addition of OMMT also gave an increase of the elongation, the dynamic storage modulus, the dynamic loss modulus, and the thermal stability of nanocomposites. The increase of the elongation of nanocomposites indicates that SBS has retained good elasticity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3430–3434, 2004     

Magnetite‐functionalized graphene/poly(styrene‐butadiene‐styrene) composites: thermal and mechanical properties

Advanced polymer composites containing organic–inorganic fillers are gaining increasing attention due to their multifunctional applications. In this work, poly(styrene‐butadiene‐styrene) (SBS) composites containing magnetite‐functionalized graphene (FG) were prepared by a dissolution ? dispersion ? precipitation solution method. Evidently, through morphology studies, amounts of FG were well distributed in the SBS matrix. Improvements in neat SBS properties with respect to FG loading in terms of thermal stability, creep recovery and mechanical properties are presented. As expected, the addition of FG improved the thermal stability and mechanical properties of the composites. The yield strength and Young's modulus of the SBS increased by 66% and 146% at 5 wt% filler loading which can be attributed to the reinforcing nature of FG. Similarly, an increase in the storage and loss modulus of the composites showed a reinforcement effect of the filler even at low concentration. The results also showed the significant role of FG in improving the creep and recovery performance of the SBS copolymer. Creep deformation decreased with filler loading but increased with temperature. © 2017 Society of Chemical Industry     

Compatibilization effects of styrenic/rubber block copolymers in polypropylene/polystyrene blends

Compatibilizing effects of styrene/rubber block copolymers poly(styrene‐b‐butadiene‐b‐styrene) (SBS), poly(styrene‐b‐ethylene‐co‐propylene) (SEP), and two types of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS), which differ in their molecular weights on morphology and selected mechanical properties of immiscible polypropylene/polystyrene (PP/PS) 70/30 blend were investigated. Three different concentrations of styrene/rubber block copolymers were used (2.5, 5, and 10 wt %). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the phase morphology of blends. The SEM analysis revealed that the size of the dispersed particles decreases as the content of the compatibilizer increases. Reduction of the dispersed particles sizes of blends compatibilized with SEP, SBS, and low‐molecular weight SEBS agrees well with the theoretical predictions based on interaction energy densities determined by the binary interaction model of Paul and Barlow. The SEM analysis confirmed improved interfacial adhesion between matrix and dispersed phase. The TEM micrographs showed that SBS, SEP, and low‐molecular weight SEBS enveloped and joined pure PS particles into complex dispersed aggregates. Bimodal particle size distribution was observed in the case of SEP and low‐molecular weight SEBS addition. Notched impact strength (a_k), elongation at yield (ε_y), and Young's modulus (E) were measured as a function of weight percent of different types of styrene/rubber block copolymers. The a_k and ε_y were improved whereas E gradually decreased with increasing amount of the compatibilizer. The a_k was improved significantly by the addition of SEP. It was found that the compatibilizing efficiency of block copolymer used is strongly dependent on the chemical structure of rubber block, molecular weight of block copolymer molecule, and its concentration. The SEP diblock copolymer proved to be a superior compatibilizer over SBS and SEBS triblock copolymers. Low‐molecular weight SEBS appeared to be a more efficient compatibilizer in PP/PS blend than high‐molecular weight SEBS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 291–307, 1999     

Synthesis and characterization of poly (styrene‐b‐[(butadiene)1−x‐(ethylene‐co‐butylene)x] ‐b‐styrene) star‐like molecular polymers produced by partial hydrogenation of SBS

This article reports the synthesis and characterization of four arm star‐shaped poly(styrene‐b‐[(butadiene)_1?x‐(ethylene‐co‐butylene)_x]‐b‐styrene) (SBEBS) copolymers. A series of SBEBS copolymers with different compositions of the elastomeric block were produced by hydrogenating a given poly(styrene‐b‐butadiene‐b‐styrene) (SBS) copolymer using a catalyst prepared from bis(η⁵‐cyclopentadienyl)titanium(IV) dichloride and n‐butyllithium. The characterization was accomplished by proton nuclear magnetic resonance spectroscopy (¹H NMR), infrared spectroscopy (FTIR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). The results indicate that there is a selective saturation of the polybutadiene block over the polystyrene block; this selectivity was determined by the Ti/Li molar ratio and the concentration of Ti. It was observed that the saturation rate of the 1,2‐vinyl was higher than that of the 1,4‐trans and 1,4‐cis poly(butadiene)‐b isomers. The DSC and DMA results indicate that the degree of hydrogenation had a profound effect on the polymer's relaxation behavior. All samples exhibited a biphasic system behavior with two distinct transitions corresponding to the elastomeric and polystyrene blocks. SBEBS copolymers with higher saturation levels (>33%) exhibited a crystalline character. The TGA results indicated a characteristic weight loss temperature in all samples, with slightly higher thermal degradation stabilities in the materials with higher degrees of saturation. POLYM. ENG. SCI., 54:2332–2344, 2014. © 2013 Society of Plastics Engineers     

Morphology and mechanical properties of high‐impact polystyrene/elastomer/magnesium hydroxide composites

Ternary composites of high‐impact polystyrene (HIPS), elastomer, and magnesium hydroxide filler encapsulated by polystyrene were prepared to study the relationships between their structure and mechanical properties. Two kinds of morphology were formed. Separation of elastomer and filler was found when a nonpolar poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS) was incorporated. Encapsulation of filler by elastomer was achieved by using the corresponding maleinated SEBS (SEBS‐g‐MA). The mechanical properties of ternary composites were strongly dependent on microstructure. In this study, the composites with separate dispersion structure showed higher elongation, modulus and impact strength than those of encapsulation structure. Impact‐fracture surface observation showed that the toughening mechanism was mainly due to the massive cavitation and extensive matrix yielding. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5184–5190, 2006     

Simple route for the preparation of graphene/poly(styrene‐b‐butadiene‐b‐styrene) nanocomposite films with enhanced electrical conductivity and hydrophobicity

This paper reports a simple route for the preparation of graphene/poly(styrene‐b‐butadiene‐b‐styrene) (SBS) nanocomposite films employing a vacuum filtration method. Graphene is exfoliated well by an electrochemical procedure and homogeneously dispersed in the polymer matrix. The prepared nanocomposite films were characterized by XRD, Fourier transform IR (FTIR) spectroscopy, X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, AFM and SEM. Morphological studies showed that graphene formed a smooth coating over the surface of SBS. The increase in graphene concentration induces the wrinkling of graphene sheets at the composite surface which causes a further increase in surface roughness. The FTIR, Raman and XPS spectra of graphene/SBS nanocomposite films indicate the strong interactions between graphene and the polymer matrix. According to the XRD patterns, introducing SBS into graphene did not modify the graphene structure additionally, i.e. the crystal lattice parameters do not depend on SBS content in graphene/SBS nanocomposite films. The graphene/SBS nanocomposite films also exhibited better hydrophobicity due to the increased surface roughness and lower sheet resistivity (reduced 10 times) compared to exfoliated graphene. © 2018 Society of Chemical Industry     

Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Facile preparation of Cu(I) impregnated MIL‐101(Cr) and its use in a mixed matrix membrane for olefin/paraffin separation

Cu(I) impregnated MIL‐100(Cr) [denoted Cu@MIL‐101(Cr)] is fabricated by a facile method and utilized in mixed matrix membranes (MMMs) for propylene/propane separation. Cu(I) is prepared from a CuCl₂ solution via mild reduction process using sodium sulfite as the reducing agent. The filler is incorporated into a polystyrene‐b‐polybutadiene‐b‐polystyrene (SBS) block copolymer matrix to form MMMs. As a result, both the permeability and selectivity of propylene/propane are improved after Cu(I) impregnation. The best performance is obtained for SBS/Cu@MIL‐101(Cr) MMM, and these values represent 17% and 54% improvements compared to those of SBS/MIL‐101(Cr) MMM, respectively. This result is attributed to the π‐complexation of the loaded Cu(I) by propylene gas, indicating that Cu@MIL‐101(Cr) with internal Cu(I) and a high pore volume acted as an effective filler to aid propylene/propane separation. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46545.     

A modified rheological model of viscosities for BR–SBS blends

Blends of polybutadiene (BR) and styrene–butadiene–styrene triblock copolymer (SBS) have been prepared by a two‐roll mill. The morphologies of extruded samples from a capillary rheometer were observed by scanning electron microscopy (SEM). It is found that PS phase is dispersed in the BR phase. The glass transition temperature (T_g) of the blend has been examined by using differential scanning calorimetry (DSC). From the T_g behavior and the electron microscopy study, it is found that certain degree of miscibility between the polystyrene phase and the BR phase is observed. The rheological behavior of the blend has been investigated by a capillary rheometer. It is found that the viscosity of the blend increases with increased content of PS phase. The behavior is in accord with the expected behavior of filler effect. To predict the filler effect of PS phase on the BR–SBS blend, a modified model of Chen and Cheng is proposed to elucidate the rheological properties of the BR–SBS blends with different compositions. Chen and Cheng's micromechanical model derived in Part I of this series, which relates the macroscopic shear stress to the macroscopic shear rate of a rigid non‐Newtonian suspension when the direct contribution of Brownian force is completely neglected. The agreement between the theoretical predictions and the experimental results is satisfactory. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 39–46, 1999     

A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of arm number on the properties of transparent elastomers prepared from styrene–butadiene block copolymer

A series of the SBS transparent elastomers were prepared from star‐shaped SBS having different arm number by solution‐casting. Their structure and physical properties were characterized by scanning electron microscope, ultraviolet spectrometer, wide‐angle X‐ray diffractometer, differential scanning calorimetry, dynamic mechanical thermal analysis, tensile testing, and contact angle measurements. The results revealed that the miscibility, optical transparence (T_r), tensile strength (σ_b), elongation at break (ε_b), and elasticity at low temperature of the star SBS increased with an increase of arm number. The six‐arm SBS having relatively high molecular weight exhibited a simultaneous enhancement of T_r (90% at 800 nm), σ_b (6.0 Mpa), and ε_b (1260%). This indicated that the SBS materials having six arms had higher transparence and elasticity than others. Moreover, the water contact angle on surface of the star‐shaped SBS film increased with an increase of arm number that is enhancement of hydrophobicity. Therefore, the relatively high arm number and molecular weight played an important role in the improvement of the miscibility and properties of the SBS sheets as a result of the compacted architecture of the hyperbranched molecules. This work provides a convenient way to obtain materials with both high transparence and elasticity by increasing the arm number. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 729–736, 2006     

Synthesis and thermal characterization of new dumbbell shaped POSS/PS nanocomposites: Influence of the symmetrical structure of the nanoparticles on the dispersion/aggregation in the polymer matrix

A series of three novel dumbbell shaped polyhedral oligomeric silsesquioxanes (POSS)/ polystyrene (PS) nanocomposites, at different POSS contents (3%, 5% and 10% w/w), was synthesized and characterized in order to investigate the effects of this new bridged structure on the filler‐polymer interaction and then on the thermal behavior of the obtained polymer nanostructured materials (PNMs). Nanocomposites were synthesized by in situ polymerization of styrene and the actual POSS concentration in the obtained PNMs was checked by ¹H NMR spectroscopy. Scanning electron microscopy (SEM) and FTIR spectroscopy evidenced, at the same time, the presence of filler‐polymer interactions and auto‐aggregation phenomena. Degradations were carried out into a thermobalance, in the scanning mode, at various heating rates in both inert and oxidative atmospheres. The characteristic parameters of thermal stability, namely temperature at 5% mass loss and the apparent activation energy of degradation, for the various nanocomposites were determined and an increase in the initial decomposition temperatures of PNMs with increasing the POSS contents was observed. The results are discussed and interpreted. POLYM. COMPOS., 36:1394–1400, 2015. © 2014 Society of Plastics Engineers     

Proton conducting crosslinked polymer electrolyte membranes based on SBS block copolymer

A series of crosslinked polymer electrolyte membranes with controlled structures were prepared based on poly(styrene‐b‐butadiene‐b‐styrene) (SBS) triblock copolymer and a sulfonated monomer, 2‐sulfoethyl methacrylate (SEMA). SBS membranes were thermally crosslinked with SEMA in the presence of a thermal‐initiator, 4,4′‐azobis(4‐cyanovaleric acid) (ACVA), as confirmed by FT‐IR spectroscopy. The water uptake and ion exchange capacity (IEC) of membranes increased almost linearly with SEMA concentrations due to the increase of SO groups. However, the proton conductivity of membranes increased linearly up to 33 wt % of SEMA, above which it abruptly jumped to 0.04 S/cm presumably due to the formation of well‐developed proton channels. Microphase‐separated morphology and amorphous structures of crosslinked SBS/SEMA membranes were observed using wide angle X‐ray scattering (WAXS), small angle X‐ray scattering (SAXS), and transmission electron microscopy (TEM). The membranes exhibited good mechanical properties and high thermal stability up to 250°C, as determined by a universal testing machine (UTM) and thermal gravimetric analysis (TGA), respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis of a chiral stationary phase with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] by surface‐initiated atom transfer radical polymerization and its chiral resolution efficiency

A chiral stationary phase (CSP) with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] was synthesized by the surface‐initiated atom transfer radical polymerization (SI‐ATRP) of cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)‐6‐acrylate after the SI‐ATRP of styrene on the surface of silicon dioxide supports in pyridine. The successful preparation of the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] was confirmed via Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X‐ray photoelectron spectroscopy, elemental analysis, and thermal analysis. The applicability for the chiral resolution of the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐diphenylcarbamate)] was evaluated with high‐performance liquid chromatography with 10 racemates under various mobile phases of hexane/alcohol, hexane/tetrahydrofuran (THF), and hexane/chloroform. The results show that the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐diphenylcarbamate)] could be used in THF and chloroform as eluents. The chiral resolutions of the commercial Chiracel OD, the CSP with cellulose 2,3‐bis(3,5‐dimethylphenylcarabmate), and the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] prepared by SI‐ATRP were examined. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Viscoelastic relaxation of styrene–butadiene–styrene block copolymers with different topological structures

The viscoelastic relaxation of linear styrene–butadiene–styrene triblock copolymer (l‐SBS) and star styrene–butadiene–styrene triblock copolymer (s‐SBS) with four arms were investigated with differential scanning calorimetry and dynamic rheological measurements. Three characteristic viscoelastic responses of l‐SBS and s‐SBS in the plot of the loss tangent (tan δ) and temperature at different frequencies (ω's), which corresponded to the relaxation of the polybutadiene (PB) block (peak I), the glass transition of the polystyrene (PS) phase (peak II), and the mutual diffusion between the PB blocks and PS blocks (peak III), respectively, were observed in the experimental range. Although ω was 0.1 rad/s, a noticeable peak III was gained for both l‐SBS and s‐SBS. The dynamic storage modulus (G′) of l‐SBS showed two distinct types of behavior, depending on the temperature. At temperature (T) < T₂ (where T₂ is the temperature corresponding to peak II), G′ of l‐SBS displayed a very weak ω dependency. In contrast, at T > T₂, G′ decayed much more rapidly. However, G′ of s‐SBS displayed a very weak ω dependency at both T < T₂ and T > T₂. Only near T₂ did s‐SBS decay with ω a little sharply. These indicated, in contrast to l‐SBS, that s‐SBS still exhibited more elasticity even at T > T₂ because of its crosslinking point between the PB blocks (the star structure). In the lower ω range, l‐SBS exhibited a stronger peak III than s‐SBS despite the same styrene content for l‐SBS and s‐SBS. The high tan δ value of peak III for l‐SBS was considered to be related to the internal friction among the PB blocks or the whole l‐SBS chain, not the PS blocks. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Studies on morphology and mechanical properties of PP/HIPS blends from postconsumer plastic waste

The aim of this work was to study the compatibilizing effect of the triblock copolymer poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS) on the morphology and mechanical properties of virgin and recycled polypropylene/high‐impact polystyrene (PP/HIPS) blends. The components of the blend were obtained from municipal plastics waste (MPW), with the PP obtained from blue mineral water bottles, symbolized as PP_b, and the HIPS from disposable cups. These materials were preground, washed only with water, dried with hot air, and ground again (PP_b) or agglutinated (HIPS). Blends of PP_b and HIPS in three weight ratios (6:1, 6:2, and 6:3) were prepared, and three concentrations of SEBS (5.0, 6.0, and 6.7% w/w) were used for investigations of its compatibilizing effect. Scanning electron microscopy (SEM) showed that SEBS reduced the diameter of HIPS dispersed particles that were globular and fibril shaped, along with improving the adhesion between the dispersed phase and the matrix. On the other hand, SEBS interactions with PP_b and HIPS influenced the mechanical properties of the compatibilized PP_b/HIPS/SEBS blends. The optimal concentration of SEBS was 5 wt % for application to composite films with similar characteristics to synthetic paper. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 747–751, 2003     

Investigation on the morphological and mechanical properties of (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) ternary blends

In this work, ternary polymer blends based on (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) (SEBS) triblock copolymer and a varying concentration of the reactive (maleic anhydride)‐grafted SEBS were prepared by using a melt‐blending process. The effects of the material parameters (composition of ternary blends and SEBS/[{maleic anhydride}‐grafted SEBS] concentration ratio) and blending sequence on the morphological and mechanical properties of ternary blends were studied. Taguchi experimental design methodology was employed to design the experiments and select the material and processing parameters for the optimized mechanical properties. Tensile properties (Young's modulus and yield stress) and impact strength were considered as the response variables. It was demonstrated that there is a meaningful relationship between the composition of blends, processing parameters, observed phase structure, and obtained mechanical properties. The mechanical tests showed that the highest impact strength was achieved as the dispersion of the rubbery phase achieved an optimum size of about 1 μm. J. VINYL ADDIT. TECHNOL., 23:329–337, 2017. © 2015 Society of Plastics Engineers     

Preparation and characterization of poly(styrene‐b‐butadiene‐b‐styrene)/montmorillonite nanocomposites

With some polymerizable small molecules grafting onto the montmorillonite surface, we disposed the clay through in‐situ emulsion polymerization, and the structure of the modified montmorillonites were studied through Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD). The nanocomposites of poly(styrene‐b‐butadiene‐b‐styrene) (SBS)/montmorillonite with excellent mechanical properties were prepared by mixing SBS and the modified montmorillonite on the double rollers at 150°C. The exfoliation of the layered silicates was confirmed by XRD analysis and transmission electron microscopy (TEM) observation. After mechanical kneading of the molten nanocomposites, the exfoliation structure of the silicates is still stable for polystyrene macromolecules grafting onto the silicates. Upon the addition of the modified montmorillonite, the tensile strength, elongation at break and tear strength of the nanocomposites increased from 22.6 MPa to 31.1 MPa, from 608% to 948%, from 45.32 N/mm to 55.27 N/mm, respectively. The low‐temperature point of glass‐transition temperature (T_g) of the products was about −77°C, almost constant, but the high‐temperature point increased from 97°C to 106°C. In addition, the nanocomposites of SBS and modified montmorillonites showed good resistance to thermal oxidation and aging. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Preparation and characterization of styrene/styryl–polyhedral oligomeric silsesquioxane hybrid copolymers

BACKGROUND: Organic–inorganic nanocomposites were prepared by copolymerization of various monomers and polyhedral oligomeric silsesquioxane (POSS) derivatives. Preliminary results showed that styrene/styryl–POSS copolymers could be obtained using CpTiCl₃ catalyst. In the work reported here, the copolymerization of styrene and styryl‐substituted POSS was studied in detail for a more effective catalyst, Cp*TiCl₃. RESULTS: The glass transition temperature (T_g) of the copolymers prepared increased with increasing POSS content. The degradation temperature (T_d) of the copolymers was 60 °C higher than that of syndiotactic polystyrene under nitrogen. Although the thermal properties were improved by incorporation of POSS, the catalytic activity decreased with POSS content. The racemic triad and syndiotactic index of the copolymers decreased with increasing POSS content. Gel permeation chromatograms of the copolymers exhibited multimodal distribution due to the presence of multi‐active centres, which were formed by interaction of Ti with the POSS siloxane linkage. CONCLUSION: With the incorporation of POSS, the thermal properties of polystyrene were improved. The styrene/styryl–POSS copolymers are formed through the various active sites arising from the interactions of Ti with POSS. Copyright © 2008 Society of Chemical Industry