Modulating the mechanical properties of poly(diol citrates) via the incorporation of a second type of crosslink network

Novel citric acid‐based polyesters were synthesized by condensation of citric acid, 1,8‐octanediol, and unsaturated monomers such as glycerol 1,3‐diglycerolate diacrylate and bis(hydroxypropylfumarate). Under the synthesis conditions used, the crosslinked elastomeric network exhibited a wide range of mechanical properties. The mechanical properties of acrylated elastomers ranged from 7.4 to 75.9 MPa for Young's modulus, 2.8 to 15.7 MPa for ultimate tensile stress, and 86 to 133% for elongation at break. The mechanical properties of fumarate‐containing elastomers ranged from 16.4 to 38.3 MPa for Young's modulus, 5.5 to 10.2 MPa for ultimate tensile stress, and 218 to 260% for elongation at break, which depended on the content of 1‐vinyl‐2‐pyrrolidinone. Addition of a secondary crosslink network is a viable method to increase the range of mechanical properties of citric acid‐based biodegradable elastomers. The glass transition temperature (T_g) of the elastomers is between ?12.7 and ?1.6°C, confirming that all the elastomers are in a rubbery state at room temperature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(trimethylene terephthalate‐block‐tetramethylene oxide) elastomer/single‐walled carbon nanotubes nanocomposites: Synthesis,structure, and properties

Nanocomposites based on poly(trimethylene terephthalate)‐block‐poly(tetramethylene oxide) (PTT‐PTMO)‐segmented copolymer and COOH‐functionalized single‐walled carbon nanotubes (SWCNTs) were prepared by in situ polymerization method. The obtained nanocomposites were characterized by thermogravimetric analysis, scanning electron microscopy, differential scanning calorimetry (DSC), DMTA, wide‐angle x‐ray scattering (WAXS), small‐angle X‐ray scattering, and tensile testing. The nanocomposites with low SWCNTs loading (<0.5 wt %) shows uniform dispersion of CNT in polymer matrix. As the SWCNTs loading in the nanocomposites increase, the significant improvement of thermo‐oxidative stability was observed. It was found that the nanocomposites have slightly higher degree of crystallinity (determined by DSC and WAXS) of poly(trimethylene terephthalate) (PTT) hard phase than neat PTT‐PTMO copolymer. The melting point of PTT hard phase and glass transition temperature of poly(tetramethylene oxide)‐rich phase were not affected by the presence of CNTs in polymer matrix. The SWCNTs played a role as nucleating agent in PTT‐PTMO matrix, which led to increase in the crystallization rate. Tensile tests showed that the tensile strength of the nanocomposites with 0.05–0.3 wt % loading of SWCNTs have improved tensile strength in comparison to the neat PTT‐PTMO copolymer without reduction elongation at break. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Biodegradable and biocompatible nanocomposites of poly(ϵ‐caprolactone) with hydroxyapatite nanocrystals: Thermal and mechanical properties

Nanocomposites of poly(?‐caprolactone) (PCL) with hydroxyapatite nanocrystals (HAP) prepared through the solvent‐cast technique were characterized by means of transmission electron microscopy (TEM), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and tensile tests. Such composites are of great importance to make bone‐like substitutes as HAP nanocrystals have similar composition, morphology, and crystal structure as natural apatite crystals. The TEM micrograph reveals the nanocrystals dispersed homogeneously in the matrix at a microscale level. The solvent‐cast samples commonly show much higher melting points and crystallinity than the melt‐quenched samples, due to a lower undercooling as well as more sufficient time to crystallize. For both cases of samples, the melting point decreases slightly with HAP content while the level of crystallinity attained by the PCL component is not hindered by the nanocrystals. Both the glass transition temperatures and the nonisothermal crystallization temperatures are composition dependent. The tensile modulus increases with increasing HAP content while the yield stress is almost invariant with composition. Theoretical prediction of the modulus based on Halpin–Tsai equations shows excellent agreement with the experimental result. By analysis of the variation in fracture stress and strain with composition, a ductile‐to‐quasi‐brittle transition is revealed to be operative for the nanocomposites, as also can be seen by SEM. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 676–683, 2002     

Thermal and mechanical properties of poly(butylene succinate) nanocomposites with various organo‐modified montmorillonites

Nanocomposites based on biodegradable poly(butylene succinate) (PBS) and layered silicates were prepared by melt intercalation. Nonmodified montmorillonite (MMT) and MMTs (DA‐M, ODA‐M, ALA‐M, LEA‐M, and HEA‐M) organo‐modified by protonated ammonium cations {i.e., those of dodecylamine, octadecylamine, 12‐aminolauric acid, N‐lauryldiethanolamine, and 1‐[N,N‐bis(2‐hydroxyethyl)amino]‐2‐propanol, respectively} were used as layered silicates. From morphological studies using transmission electron microscopy, DA‐M, ODA‐M, and LEA‐M were found to be dispersed homogeneously in the matrix polymer, whereas some clusters or agglomerated particles were observed for ALA‐M, HEA‐M, and MMT. The enlargement of the difference in the interlayer spacing between the clay and PBS/clay composite, as measured by X‐ray diffraction, had a good correlation with the improvement of the clay dispersion and with the increase in the tensile modulus and the decrease in the tensile strength of the PBS composites with an inorganic concentration of 3 wt %. Dynamic viscoelastic measurements of the PBS/LEA‐M nanocomposite revealed that the storage modulus and glass‐transition temperature increased with the inorganic concentration (3–10 wt %). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1463–1475, 2004     

Facile synthesis of extremely biocompatible double‐network hydrogels based on chitosan and poly(vinyl alcohol) with enhanced mechanical properties

An easy and ecofriendly method for designing double‐network (DN) hydrogels based on chitosan and poly(vinyl alcohol) (PVA) with high mechanical performance is described. When covalent bonds in the networks are used as crosslinking agents in the achievement of a higher mechanical strength, the irreversible deformation of these hydrogels after a large force is applied is still one of the most important obstacles. To overcome this problem, we used physical crosslinking for both networks. The mechanical strength, surface morphology, and cytotoxicity of the films were studied by tensile testing, scanning electron microscopy analysis, and an MTT assay. The synthesized chitosan–PVA DN hydrogels showed a large improvement in the tensile strength to 11.52 MPa with an elongation of 265.6%. The surface morphologies of the films demonstrated the effective interactions between the two networks and a suitable porosity. Also, because of the use of a natural polymer and honey as a plasticizer, the cell culture indicated that the synthesized DN hydrogels had good biocompatibility (with 327.49 ± 11.22% viability) and could be used as capable biomaterials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45752.     

Preparation,crystallization, and properties of biodegradable poly(butylene adipate‐co‐terephthalate)/organomodified montmorillonite nanocomposites

Intercalated and exfoliated nanocomposites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and Cloisite 30B (C30B) were fabricated by a solution‐casting method to study the effects of the clay loading on the crystallization behavior, thermal stability, and dynamic mechanical properties of PBAT in PBAT/C30B nanocomposites. X‐ray diffraction and transmission electron microscopy results indicated the formation of exfoliated nanocomposites at low clay loadings (<5 wt %) and a mixture of exfoliated and intercalated nanocomposites with a clay content of 8 wt % throughout the PBAT matrix. Nonisothermal melt crystallization studies indicated that C30B enhanced the crystallization of PBAT, apparently because of a heterogeneous nucleation effect. Moreover, an attempt was made to quantitatively study the influence of the presence of C30B and its contents on the nucleation activity of PBAT in the PBAT/C30B nanocomposites. The thermal stability of PBAT decreased slightly in the nanocomposites. However, the storage modulus of PBAT apparently increased with the C30B loading increasing in the PBAT/C30B nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Blends of poly(d,l‐lactide) with polyhedral oligomeric silsesquioxanes‐based biodegradable polyester: Synthesis,morphology, miscibility,and mechanical property

A highly branched hybrid copolymer based on polyhedral oligomeric silsesquioxane (POSS) was designed to improve the brittleness of poly(d,l‐lactide) (PDLLA). The toughening material was synthesized using POSS‐OH as the core, which initiated the ring‐opening polymerization of ε‐caprolactone and d,l‐lactide sequentially to form the highly branched POSS‐g‐poly (ε‐caprolactone)‐b‐poly(d,l‐lactide) (POSS‐g‐PCL‐b‐PLA) copolymer with eight PCL‐b‐PLA arms. The POSS‐g‐PCL‐b‐PLA copolymer had a very good dispersion in the PDLLA matrix with the size of microdomains smaller than 1 µm when added at a low content below 10 wt %. In related to the nano‐scale size of microdomains in the blends, the crystallinity of PCL blocks was significantly suppressed. Thus, the addition of POSS‐g‐PCL‐b‐PLA is very effective to improve the roughness of the matrix polymer when added at a low content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40776.     

Preparation of porous poly(D,L‐lactide) and poly(D,L‐lactide‐co‐glycolide) membranes by a phase inversion process and investigation of their morphological changes as cell culture scaffolds

Porous membranes composed of the biodegradable polyesters poly(D,L ‐lactide) (PLA) and poly(D,L ‐lactide‐co‐glycolide) (PLGA) were prepared by a phase inversion process. The molecular weights of the polymers and the concentrations of the polymer solutions affected the pore size and structure of the PLA and PLGA membranes. The molecular weights and morphological changes of the membranes as a function of time were investigated under incubation at 37°C in a humidified 5% CO₂ atmosphere. The pores that formed in the membranes changed dramatically with increasing time under these conditions. From the thermal characterization of the polymers in their dry and wet states, we found that the glass‐transition temperatures of PLA and PLGA affected morphological structure changes in the porous membranes. We also prepared a collagen‐coated membrane to improve the interaction between the cell and the substrate, and we observed that the collagen coating enhanced the attachment and growth of Chinese hamster ovary cells on the substrate. Finally, we found that only PLA was a suitable material to prepare a porous membrane scaffold with the phase inversion process with PLA, and a collagen coating was necessary for cell culture on the membrane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2082–2092, 2004     

Graphene‐reinforced biodegradable poly(ethylene succinate) nanocomposites prepared by in situ polymerization

In this study, poly(ethylene succinate)(PES)/graphene nanocomposites were facilely prepared by in situ melt polycondensation of succinic acid and ethylene glycol in which contained well dispersed graphene oxide (GO). Fourier transform infrared (FTIR), GPC, TGA, and XRD were used to characterize the composites. The FTIR spectra and TGA measurement confirmed that PES chains had been successfully grafted onto GO sheets along with the thermal reduction of GO to graphene during the polymerization. GPC results indicated that increasing amounts of graphene caused a slight decrease in number average molecular weight of PES matrix when polymerization time was kept constant. The content of grafted PES chains on graphene sheets was also determined by TGA and was to be about 60%, which made the graphene sheets homogeneously dispersed in the PES matrix, as demonstrated by SEM and XRD investigations. Furthermore, the incorporation of thermally reduced graphene improved the thermal stability and mechanical properties of the composites significantly. With the addition of 0.5 wt % graphene, onset decomposition temperature of the composite was increased by 12°C, and a 45% improvement in tensile strength and 60% in elongation at break were also achieved. The enhanced performance of the composites is mainly attributed to the uniform dispersion of graphene in the polymer matrix and the improved interfacial interactions between both components. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3212–3220, 2013     

Effects of copolymer microstructure on the properties of electrospun poly(l‐lactide‐co‐ε‐caprolactone) absorbable nerve guide tubes

The main objective of this work has been to study the effects of copolymer microstructure, both chemical and physical, on the microporosity, in vitro hydrolytic degradability and biocompatibility of electrospun poly(l ‐lactide‐co‐ε‐caprolactone), PLC, copolymer tubes for potential use as absorbable nerve guides. PLC copolymers with L : C compositions of 50 : 50 and 67 : 33 mol % were synthesized via the ring‐opening copolymerization of l ‐lactide (L) and ε‐caprolactone (C) at 120°C for 72 h using stannous octoate (tin(II) 2‐ethylhexanoate) and n‐hexanol as the initiating system. Electrospinning was carried out from solution in a dichloromethane/dimethylformamide (7 : 3 v/v) mixed solvent at room temperature. The in vitro hydrolytic degradation of the electrospun PLC tubes was studied in phosphate buffer saline over a period of 36 weeks. The microporous tubes were found to be gradually degradable by a simple hydrolysis mechanism leading to random chain scission. At the end of the degradation period, the % weight retentions of the PLC 50 : 50 and 67 : 33 tubes were 15.6% and 70.2%, respectively. Pore stability during storage as well as cell attachment and proliferation of mouse fibroblast cells (L929) showed the greater potential of the PLC 67 : 33 tubes for use as temporary scaffolds in reconstructive nerve surgery. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4357–4366, 2013     

Thermal and dynamic mechanical properties of organic–inorganic hybrid composites of itaconate‐containing poly(butylene succinate) and methacrylate‐substituted polysilsesquioxane

Itaconate‐unit‐containing poly(butylene succinate) (PBSI) was synthesized by the reaction of 1,4‐butanediol, succinic acid, and itaconic acid in a molar ratio of 2.0 : 1.0 : 1.0, and the obtained PBSI was reacted with methacryl‐group‐substituted polysilsesquioxane (ME‐PSQ) in the presence of benzoyl peroxide (BPO) at 130°C to produce PBSI/ME‐PSQ hybrid composites. The thermal and dynamic mechanical properties of the PBSI/ME‐PSQ hybrid composites were investigated in comparison with those of PBSI cured at 130°C in the presence of BPO. As a result, the hybrid composites showed a much higher thermal degradation temperature and storage modulus in the rubbery state than the cured PBSI (C‐PBSI). The thermal degradation temperature and storage modulus of the hybrid composites increased with increasing ME‐PSQ content. The glass‐transition temperature, measured by dynamic mechanical analysis of the hybrid composites, somewhat increased with increasing ME‐PSQ content. However, the glass‐transition temperatures of all the hybrid composites were lower than that of C‐PBSI. Although the IR absorption peak related to C?C groups was not detected for C‐PBSI, some olefinic absorption peaks remained for all the hybrid composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,characterization and properties of biocompatible poly(glycerol sebacate) pre‐polymer and gel

Poly(glycerol sebacate) (PGS) is an elastomer with potential biomedical applications but it suffers from problems with irreproducible synthesis and the unacceptable toxicity of very soft PGS elastomers. To establish the reason for these problems, PGS was synthesized using different temperatures and reaction times, and the reaction was monitored by titration of the unreacted carboxylic groups and measurement of the mass loss during synthesis. It was found that evaporation of glycerol was a major cause of irreproducibility of the elastomer synthesis and this was more significant at higher reaction temperatures. The polymer microstructure was analysed using NMR spectroscopy and all twelve acylglyceride ¹³C‐signals as well as two small extra peaks of the residual glycerol were observed for the pre‐polymer. For the PGS gel, the glyceride moieties were characterized using NMR spectroscopy for the first time. The modulus and ultimate tensile strength of the gel increased with longer cure times and at higher cure temperatures while the elongation to break decreased and this was interpreted in terms of network theory. The cell viability of mouse fibroblasts was better for PGS samples with a higher conversion.© 2012 Society of Chemical Industry     

Synthesis,characterization, and in vitro biocompatibility study of novel disulfide cross‐linked hydrogels based on poly(amic acid)

In this study, novel disulfide cross‐linked hydrogels were designed and synthesized. First, ethylenediaminetetraacetic dianhydride reacted with butanediamine and amino‐terminated polyethylene glycol via N‐acylation reaction to give biocompatible poly(amic acid) (PAA) with pendant carboxyl groups; then, the amino groups of cystamine reacted with carboxyl groups of PAA to generate disulfide cross‐linked network polymer (PAA‐SS). Fourier transform infrared spectroscopy, ¹H nuclear magnetic resonance imaging, gel permeation chromatography with multiangle laser light scattering, potentiometric titration, rheology, hydrolytic degradation, morphology, porosity, and in vitro biocompatibility studies were used to qualitatively and quantitatively characterize the obtained polymers. The results indicated that the equilibrium swelling ratio of the PAA‐SS decreased with the increase in Rm. The PAA‐SS provided good mechanical strength to maintain their integrity, and the storage modules (G′) of the hydrogels can be adjusted by Rm. The PAA‐SS presented co‐continuum pores, and the pore size correlated with the cross‐linking degree. The degradation of PAA‐SS could be controlled by regulating the concentration of dithiothreitol. Particularly, the PAA‐SS possessed an excellent biocompatibility, as the average proliferating rate of osteoblasts on PAA‐SS was appreciably higher than that on PAA and glass coverslips. In conclusion, the above obtained results demonstrate that the performance of the PAA‐SS outbalance and facilitate the application in biomedical region, particularly in bone tissue regeneration. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40930.     

Study of carbon black‐filled poly(butylene succinate)/polylactide blend

In this study, carbon black (CB) was used to control the conductivity and the compatibility of immiscible poly(butylene succinate)/polylactide (PBS/PLA) blend. It is shown that most of the CB particles are selectively dispersed in the matrix PBS phase because of the viscosity ratio of the blend components. The increasing viscosity of PBS phase prevents the coalescence of the dispersed PLA domain during the melt mixing. The domain sizes of PLA are refined when compared with that of blank PBS/PLA blend. The ternary composite shows an onset of the electrical conductivity at low filler loadings (1.5 wt %), which is attributed to a percolation of CB in the insulating matrix polymer. Moreover, the composites exhibited remarkable improvement of rheological properties in the melt state when compared with that of blank PBS/PLA blend. According to the van Gurp‐Palmen plot, the rheological percolation threshold for ternary systems is lower than 1.5 wt %. Furthermore, the ternary composites present improved mechanical properties and thermal stability even at very low loading levels of the CB. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis,self‐assembly,and drug release behavior of star‐shaped poly(ε‐caprolactone)‐b‐poly(ethylene oxide) block copolymer with porphyrin core

A serial of star‐shaped poly(ε‐caprolactone)‐b‐poly(ethylene oxide) (SPPCL‐b‐PEO) block copolymers with porphyrin core were successfully synthesized from ring‐opening polymerization (ROP) of ε‐caprolactone (CL) initiated with porphyrin core, followed by coupling reaction with a hydrophilic polymer poly(ethylene oxide) (PEO) shell. The structure of this novel copolymer were synthesized and thoroughly characterized by Nuclear Magnetic Resonance (NMR), Gel Permeation Chromatography (GPC), Fourier Transform Infrared Spectroscopy (FTIR). Notably, the as‐prepared porphyrin‐cored star‐shaped copolymer could self‐assembly into different structures determined by transmission electron microscopy (TEM) and dynamic lighting scattering (DLS), which provides the great potential of using this well‐defined photodynamic therapy material for drug delivery system. Particularly, the doxorubicin‐loaded SPPCL‐b‐PEO nanosphere exhibits property of pH‐induced drug release. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40996.     

Transport Properties of Modified Montmorillonite‐Poly(ε‐caprolactone) Nanocomposites

A series of montmorillonite‐poly(ε‐caprolactone) nanocomposites were prepared according to a two‐stage procedure. In the first step Na‐type silicate clay was cation exchanged with protonated 12‐aminolauric acid. In the second step ε‐caprolactone was intercalated in the modified clay and ring‐opening polymerized. The clay content was varied regularly from 0 to 44 wt.‐%, with exfoliation of the silicate layers being detected by X‐ray diffraction in the nanocomposites dispersing up to at least 16 wt.‐% clay. Crystallization of poly(ε‐caprolactone) was not prevented in the nanocomposites, although it proceeded to a lower extent/order than in a homopolymer sample. The transport properties were investigated using water or dichloromethane as vapor permeants. In each case, a dual sorption behavior was observed as a function of the vapor activity because of the occurrence of different sorption mechanisms. The permeability of the nanocomposites to either permeant decreased with increasing clay content. In particular, the permeability behavior to water was largely dominated by the diffusion parameter.     

Tribological properties of micro‐ and nanoparticles‐filled poly(etherimide) composites

It has been found that nano‐ or microsized inorganic particles in general enhance the tribological properties of polymer materials. In the present study, 5 vol % nano‐TiO₂ or micro‐CaSiO₃ was introduced into a polyetherimide (PEI) matrix composite, which was filled additionally with short carbon fibers (SCF) and graphite flakes. The influence of these inorganic particles on the sliding behavior was investigated with a pin‐on‐disc testing rig at room temperature and 150°C. Experimental results showed that both particles could reduce the wear rate and the frictional coefficient (μ) of the PEI composites under the applied testing conditions. At room temperature, the microparticles‐filled composites exhibited a lower wear rate and μ, while the nano‐TiO₂‐filled composites possessed the lowest wear rate and μ at elevated temperature. Enhancement in tribological properties with the addition of the nano‐particles was attributed to the formation of transfer layers on both sliding surfaces together with the reinforcing effect. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1678–1686, 2006     

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites with improved thermal and mechanical properties

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites in the form of films are prepared by simple solution processing. The structure and properties of these nanocomposites are studied using X‐ray diffractions, scanning electron microscopy, Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. The results indicate that graphene oxide is dispersed on a molecular scale and aligned in the poly(vinyl alcohol) matrix, and there exists strong interfacial interactions between both components, which are responsible for the significant improvement in the thermal and mechanical properties of the nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development and material properties of poly(lactic acid)/poly(3‐hydroxybutyrate‐co−3‐hydroxyvalerate)‐based nanocrystalline cellulose nanocomposites

This study is focused on the development and analysis of the thermal and structural behavior of nanocrystalline cellulose (NCC)‐based bionanocomposites (BCs). Nanocrystalline cellulose was prepared by controlled acid hydrolysis of oil palm empty fruit bunch fibers. The resulting NCC was surface modified using TEMPO‐mediated oxidation and solvent exchange methods for surface functionalization and also to improve dispersion of fillers. Solvent exchange NCC reinforced polymer blend containing poly(lactic acid)/poly‐(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) was prepared by using solution casting technique at various NCC loading percentages. The addition of NCC resulted in the improvement of structural, thermal, and mechanical properties of BCs as compared to that of the polymer blend. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44328.     

Functionalization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) films via surface‐initiated atom transfer radical polymerization: Comparison with the conventional free‐radical grafting procedure

We modified hydrophobic poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBHV) films with hydrophilic chains to control their surface properties. We designed and investigated surface‐initiated atom transfer radical polymerization (SI‐ATRP) to modify the PHBHV films by grafting poly(2‐hydroxyethyl methacrylate) (PHEMA) from the surface. This method consisted of two steps. In the first step, amino functions were formed on the surface by aminolysis; this was followed by the immobilization of an atom transfer radical polymerization initiator, 2‐bromoisobutyryl bromide. In the second step, the PHEMA chains were grafted to the substrate by a polymerization process initiated by the surface‐bound initiator. The SI‐ATRP technique was expected to favor a polymerization process with a controlled manner. The experimental results demonstrate that the grafting density was controlled by the reaction conditions in the first step. The grafted films were analyzed by Fourier transform infrared spectroscopy, contact angle testing, scanning electron microscopy, and energy‐dispersive X‐ray spectroscopy. The results show that grafted chains under the SI‐ATRP method were preferentially located on the surface for surface grafting and in the bulk for conventional free‐radical polymerization initiated by benzoyl peroxide. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011