Adhesion property of novel polyimides with 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride

Novel polyimides were synthesized from 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride (6FPPMDA) by a conventional two‐step process: the preparation of poly(amic acid) followed by solution imidization via refluxing in p‐chlorophenol. The diamines used for polyimide synthesis included bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, bis(3‐aminophenyl)‐4‐trifluoromethylphenyl phosphine oxide, and bis(3‐aminophenyl)phenyl phosphine oxide. The synthesized polyimides were designed to have a molecular weight of 20,000 g/mol by off‐stoichiometry and were characterized by Fourier transform infrared, NMR, differential scanning calorimetry, and thermogravimetric analysis. In addition, their intrinsic viscosity, solubility, water absorption, and coefficient of thermal expansion (CTE) were also measured. The adhesion properties of the polyimides were evaluated via a T‐peel test with bare and silane/Cr‐coated Cu foils, and the failure surfaces were investigated with scanning electron microscopy. The 6FPPMDA‐based polyimides exhibited high glass‐transition temperatures (280–299°C), good thermal stability (>530°C in air), low water absorption (1.46–2.16 wt %), and fairly low CTEs (32–40 ppm/°C), in addition to good adhesion properties (83–88 g/mm) with silane/Cr‐coated Cu foils. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1801–1809, 2005     

Synthesis,characterization, thermal and optical properties of soluble polyimides derived from an unsymmetrical diamine

A new unsymmetrical diamine monomer, 2,4‐diaminophenyl [4′‐(2′′,6′′‐diphenyl‐4′′‐pyridyl)phenyl]ether, was successfully synthesized by nucleophilic substitution of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2′,6′‐diphenyl‐4′‐pyridyl) phenol. The diamine monomer was characterized by FTIR, ¹H and ¹³C NMR, and elemental analysis techniques and used for the preparation of novel polyimides (PIs) by reaction with commercially available tetracarboxylic dianhydrides such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs with inherent viscosities ranged from 0.43 to 0.48 dL/g were readily soluble in many organic solvents and afforded tough and flexible films by solution casting. These polymers exhibited T_gs between 237 and 294°C, and 10% weight loss temperatures in excess of 500°C with up to 56% char yield at 600°C in air. Their maximum fluorescence emission in dilute (0.2 g/dL) NMP solution appeared at 450 nm. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of polyimides from novel 1-(3′,5′-bis(trifluoromethyl)benzene) pyromelliticdianhydride (6FPPMDA)

Mono-substituted dianhydride monomer, 1-(3′,5′-bis(trifluoromethyl)phenyl) pyromellitic dianhydride (6FPPMDA), was prepared via the Suzuki cross coupling reaction followed by oxidation and cyclodehydration. The monomer was characterized by FT-IR, NMR, elemental analyzer (EA) and melting point apparatus. For comparison, 1-(4′-trifluoromethylphenyl)pyromellitic dianhydride (3FPPMDA) and 1-phenyl pyromellitic dianhydride (PPMDA) were also utilized. The dianhydrides were used to prepare polyimides with aromatic diamines such as bis(3-aminophenyl) 3,4-bis(trifluoromethyl)phenyl phosphine oxide (mDA6FPPO), bis(3-aminophenyl) 4-(trifluoromethyl)phenyl phosphine oxide (mDA3FPPO), bis(3-aminophenyl) phenyl phosphine oxide (mDAPPO) and 1,1-bis(4-aminophenyl)-1-phenyl-2,2,2-trifluoroethane (p3FDAm). The polyimides were synthesized via a two-step process; preparation of poly(amic-acid) in p-chlorophenol with isoquinoline, followed by solution imidization at the reflux temperature for 12 h. Polymer characterization was carried out by FT-IR, NMR, GPC, DSC and TGA, and their solubility, solution viscosity, water absorption, CTE, dielectric constant and refractive index were also evaluated.     

Phosphorus‐containing epoxy resins: Thermal characterization

Three novel aromatic phosphorylated diamines, i.e., bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl} pyromellitamic acid (AP), 4,4′‐oxo bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AB) and 4,4′‐hexafluoroisopropylidene‐bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AF) were synthesized and characterized. These amines were prepared by solution condensation reaction of bis(3‐aminophenyl)methyl phosphine oxide (BAP) with 1,2,4,5‐benzenetetracarboxylic acid anhydride (P)/3,3′,4,4′‐benzophenonetetracarboxylic acid dianhydride (B)/4,4′‐(hexafluoroisopropylidene)diphthalic acid anhydride (F), respectively. The structural characterization of amines was done by elemental analysis, DSC, TGA, ¹H‐NMR, ¹³C‐NMR and FTIR. Amine equivalent weight was determined by the acetylation method. Curing of DGEBA in the presence of phosphorylated amines was studied by DSC and curing exotherm was in the temperature range of 195–267°C, whereas with conventional amine 4,4′‐diamino diphenyl sulphone (D) a broad exotherm in temperature range of 180–310°C was observed. Curing of DGEBA with a mixture of phosphorylated amines and D, resulted in a decrease in characteristic curing temperatures. The effect of phosphorus content on the char residue and thermal stability of epoxy resin cured isothermally in the presence of these amines was evaluated in nitrogen atmosphere. Char residue increased significantly with an increase in the phosphorus content of epoxy network. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2235–2242, 2002     

Synthesis and property measurements of polyimides with substituted pyromellitic dianhydride for flexible printed circuits applications

Pyromellitic dianhydride‐based dianhydrides with bulky substituents, such as 1‐phenyl pyromellitic dianhydride and 1‐(4′‐trifluoromethylphenyl)pyromellitic dianhydride, were combined with bis(3‐aminophenyl)phenylphosphine oxide and 4,4′‐phenylene diamine to prepare polyimides with low coefficient of thermal expansion (～ 17 ppm/°C) and good adhesion (>100 g/mm). The polyimides were synthesized via a conventional two‐step process: preparation of poly(amic‐acid) followed by solution imidization with o‐dichlorobenzene. The molecular weights of the polyimides were controlled to 25,000 g/mol via off‐stoichiometry and the synthesized polyimides were characterized by Fourier transform infrared, nuclear magnetic resonance, differential scanning calorimetry, and thermogravimetric analysis. Their intrinsic viscosity and solubility were also measured, while adhesive property was measured via T‐peel test samples of Cu/polyimide. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies on novel semi‐2‐IPNs from polyetherimide and citraconimide

A series of novel semi‐2‐interpenetrating polymeric networks (semi‐2‐IPNs) were prepared through blending in solution using two different polyimides, biscitraconamic acid as a precursor of biscitraconimide (MBMI) with various proportions of polyetherimide (PEI) to achieve optimum properties. Biscitraconamic acid was prepared by reacting citraconic anhydride (CA), 3,3',4,4'‐benzophenone tetracarboxylic dianhydride (BTDA) and bis(3‐aminopropyl)phenyl phosphine (BAPPP) and it was characterized by differential scanning calorimetry (DSC), FTIR, and ¹H‐NMR spectroscopy. Both biscitraconamic acid and PEI were blended in N,N‐dimethylacetamide (DMAc) solution, casted and thermally cured up to 300°C to give semi‐2‐IPNs. The MBMI/PEI semi‐IPN systems were characterized by UV‐Vis spectroscopy, FTIR spectroscopy and thermal techniques. The phase morphology, isothermal aging, and water uptake of semi‐IPN systems have also been studied. The morphological studies on phase distribution were investigated by scanning electron microscopy (SEM). Thermal performance of MBMI/PEI semi‐IPN systems were evaluated by DSC and thermo gravimetric analysis (TGA). All the compositions of semi‐IPN polyimide system were stable up to 400°C and their thermal stability increased with increase in the content of PEI. Isothermal aging studies done at 300°C for various time periods showed good thermo‐oxidative stability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry     

Synthesis and properties of new aromatic polyimides based on 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride

New polyimides with enhanced thermal stability and high solubility were synthesized in common organic solvents from a new dianhydride, 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride (DBBTDA). DBBTDA was used as monomer to synthesize polyimides by using various aromatic diamines. The polymers were characterized by IR and NMR spectroscopy and elemental analysis. These polyimides had good inherent viscosities in N‐methyl‐2‐pyrrolidinone (NMP) and also high solubility and excellent thermo‐oxidative stability, with 5 % weight loss in the range 433 to 597 °C. Copyright © 2004 Society of Chemical Industry     

Microwave assisted polycondensation of polyimides by [4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,pyromellitic dianhydride] and [2,4,6‐trimethyl‐m‐phenylenediamine]. Power,time, and solvent effect

The microwave assisted polycondensation of two polyimides were studied using pyromellitic dianhydride (PMDA), and 4,4′‐(hexafluoroisopropyliden)diphthalic anhydride (6FDA) as dianhydride monomers and 2,4,6‐trimethyl‐m‐phenylenediamine (TrmPD), as diamine monomer, under microwave irradiation in DMF and DMSO solvents. The structure and performance of polymers were characterized by Fourier Transform Infrared Spectroscopy (FTIR), viscosity, density, and Thermogravimetric Analysis (TGA). The results show that the polyimides can be obtained in a short reaction time with high intrinsic viscosity and high yield. The effect of the presence of a bridging group, ? C(CF₃)₂? , in the monomer structure is apparent in the permeability parameters of the macromolecules as polymer (6FDA‐TrmPD) always presents better results than polymer (PMDA‐TrmPD). Properties as density and T_g increases with the time exposition to the microwave irradiation. Polyimides obtained present good thermal properties because they began to lose weight in a range of 8–16% at high temperature as 450°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of organosoluble polyimides based on novel flourene‐ring containing diacetamido‐diamine

A new diacetamido‐diamine monomer, N′‐[7‐(acetyl‐4‐aminoanilino)‐9,9‐dioctylflouren‐2‐yl]‐N′‐4‐aminophenyl) acetamide (ADOAc), with flourene‐based structure was prepared from the reaction of 4‐aminoacetanillide with 2,7‐dibromo‐9,9‐dioctylfluorene in the presence of 10 mol % CuI, 20 mol % N,N′‐dimethylethylene diamine as catalyst and K₂CO₃ as base. Two new flourene‐ring containing polyimides were prepared from the reaction of ADOAc with aromatic dianhydrides such as pyromellitic dianhydride (PMDA) and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA) via chemical imidization of poly(amic acid). The new diamine and the related polyimides were characterized by using conventional methods such as FT‐IR, NMR, and elemental analysis. The polyimides obtained from the reaction of ADOAc with PMDA (PIa) and of ADOAc with BTDA (PIb) had inherent viscosity of 0.49 and 0.58 dL/g respectively, and showed excellent solubility in a variety of organic solvents. The polyimides of PIa and PIb showed excellent thermal stability with 10% weight loss in nitrogen atmosphere at temperatures of 418°C and 407°C and T_g of 172°C and 167°C, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel poly(thiourea‐ether‐imide)s derived from 4,4′‐oxydiphenyl‐bis(thiourea): probing the possibility for high‐temperature applications

Our interest in the fabrication of high‐performance polyimides has led to thiourea‐substituted poly(thiourea‐ether‐imide)s (PTEIs) with good retention of thermal properties along with flame retardancy. A new aromatic monomer, 4,4′‐oxydiphenyl‐bis(thiourea) (ODPBT), was efficiently synthesized and polymerized with various dianhydrides (pyromellitic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride and 4,4′‐(hexafluoroisopropylidene)diphthalic dianhydride) via two‐stage chemical imidization to fabricate a series of PTEIs. The structural characterization of ODPBT and the polymers was carried out using Fourier transform infrared, ¹H NMR and ¹³C NMR spectral techniques along with crystallinity, organosolubility, inherent viscosity and gel permeation chromatographic measurements. PTEIs bearing C?S and ? O? moieties in the backbone demonstrated an amorphous nature and were readily soluble in various amide solvents. The novel polymers had inherent viscosities of 1.16–1.23 dL g^?1 and molecular weights of ca 90 783–96 927 g mol^?1. Their thermal stability was substantiated via 10% weight loss in the temperature range 516–530 °C under inert atmosphere. The polyimides had glass transition temperatures of 260–265 °C. Incorporation of thiourea functionalities into polymer backbones is demonstrated to be an effective way to enhance their thermal properties and flame retardancy. Thus, ODPBT can be considered as an excellent candidate for use in the synthesis of high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis,characterization and properties of TAP‐6FDA hyperbranched polyimides with different branching degrees

A series of hyperbranched polyimides were successfully synthesized by condensation polymerization of A₂‐type dianhydride monomer 2,2‐bis(3,4‐dicarboxylphenyl) hexafluoropropane dianhydride (6FDA) and B′B₂‐type triamine monomer 2,4,6‐triaminopyrimidine (TAP). Polymers with different branching degrees (DB) and terminated groups were obtained by changing the monomer addition order and the monomer molar ratio. Fourier transform infrared spectroscopy and ¹H NMR were used to verify the structure of the prepared polyimides, which indicated that the amino group still existed in all the products. The DB of the polymers indicated by ¹H NMR increased from 30% to 79% with the molar ratio of TAP:6FDA decreasing from 1:1 to 1:2. The absolute molecular weights were measured by size‐exclusion chromatography with multi‐angle laser light‐scattering detection, which suggested that the highest molecular weight would be obtained when the molar ratio of amino groups:anhydride groups of the monomers was 3:3.2. With the DB increasing, the d‐spacing values indicated by wide angle X‐ray diffraction increased from 5.15 Å to 5.68 Å and the UV ? visible spectra of the polymers exhibited decreasing cut‐off wavelengths. The 5% weight loss temperature in nitrogen increased with decreasing content of TAP monomer, and the glass transition temperatures of the obtained polyimides decreased from 282 °C to 258 °C with increasing DB. © 2013 Society of Chemical Industry     

Synthesis and properties of novel phosphorus‐containing poly(ether ether ketone ketone)s

A novel monomer, bis[4‐(4‐fluorobenzoyl)phenyl]phenylphosphine oxide, was synthesized through the reaction of bis(4‐chloroformylphenyl) phenyl phosphine oxide with fluorobenzene. Three poly(ether ether ketone ketone)s derived from bis[4‐(4‐fluorobenzoyl)phenyl]phenylphosphine oxide and different aromatic bisphenols were prepared by aromatic nucleophilic substitution reactions. The resulting polymers had inherent viscosities in the range of 0.55–0.73 dL/g. The structures of the poly(ether ether ketone ketone)s were characterized with Fourier transform infrared and ¹H‐NMR. Thermal analysis indicated that the glass‐transition temperatures of the poly(ether ether ketone ketone)s were higher than 200°C, and the 5% weight loss temperatures in nitrogen were higher than 463°C. All the polymers showed excellent solubility in polar solvents such as N‐methyl‐2‐pyrrolidone, dimethylformamide, and dimethylacetamide and could also be dissolved in chlorinated methane. The polymers afforded transparent and flexible films by solvent casting. Organic phosphorous moieties also imparted good flame‐retardancy to the polymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyether–polyimide thermoplastic elastomers. I. Synthesis and properties

A series of polyether–polyimides based on polycondensation of poly(tetramethylene oxide) glycol di-p-aminobenzoate with different molecular weights (650, 1000, 2000) and benzenetetracarboxylic acid dianhydride (BTDA) or 3,3′,4,4′-benzenetetracarboxylic acid anhydride (BPTDA) was synthesized. Infrared spectroscopy (IR), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and stress–strain tests were used to follow the imidization process and to study the structure–property relations of this family of polymers. FTIR data showed that the imidization was completed after 6 h at 140°C, which is a much lower temperature than that required for polyimides synthesized from low molecular weight diamines. DSC and DMA results indicated that the block copolymer exhibited a well-phase-separated structure and had a broad rubbery plateau from about ?70°C to 260°C, which varied with dianhydride type and hard-segment content. The BTDA series had enhanced mechanical properties compared to the BPTDA series. The excellent tensile properties of the polyether–polyimides suggest that they could be potentially used as heat-resistant thermoplastic elastomers.     

Investigations on the polyimides derived from unfunctionalized symmetric cyclopentyl‐containing alicyclic cardo‐type dianhydride

This study presents an investigation on polyimides derived from a unfunctionalized symmetric cyclopentyl‐containing alicyclic cardo‐type dianhydride with ester linkage 1,1‐bis(4‐(3,4‐dicarboxylbenzoyloxy)phenyl)cyclopentylene dianhydride (BDPCP) that was readily accessed starting from cyclopentanone through two steps in high yield. Two series of polyimides, Cardo‐type series (CPI‐x) and analogous aromatic series (ArPI‐x) were prepared from condensation of BDPCP and aromatic 3,3′,4,4′‐Oxydiphthalic dianhydride with four aromatic diamines, respectively. Comparative studies revealed that CPI polymers show more favorable properties including better solubility in organic solvents, higher transparency with lower cut‐off wavelength (λ₀) ranging in 395–375 nm than 425–405 nm, lower water absorption ranging in 0.66–1.14% and surface energy 23.71–32.77 mN/m than 1.01–1.28% and 29.52–41.99 mN/m of ArPI analogs. Meanwhile, CPI series exhibit considerable mechanical properties with tensile strengths ranging in 87.6–102.9 MPa, elongations at break 6.6–8.9%. Owing to the moderate strain in cyclopentyl ring, CPI series retain good thermal properties with the glass transition temperature (T_g) in the range of 217–271°C. Dynamic dielectric measurement revealed that Cardo‐type dianhydride BDPCP endows CPI‐4 film with lower dielectric constant (ε′) 3.34 at 1 MHz and 25°C and dielectric loss (ε′′) 0.0064 at 1 kHz and 25°C than 3.49 and 0.013 for ArPI‐4 film. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42670.     

Synthesis and characterization of novel soluble pyridine‐containing polyimides based on 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine and various aromatic dianhydrides

A new kind of pyridine‐containing aromatic diamine monomer, 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine (PAPP), was successfully synthesized by a modified chichibabin reaction of benzaldehyde and a substituted acetophenone, 4‐(4‐nitrophenoxy)‐acetophenone (NPAP), followed by a reduction of the resulting dinitro compound 4‐phenyl‐2,6‐bis[4‐(4‐nitrophenoxy)phenyl]‐pyridine (PNPP) with Pd/C and hydrazine monohydrate. The aromatic diamine was employed to synthesize a series of new pyridine‐containing polyimides by polycondensation with various aromatic dianhydrides in N‐methy‐2‐pyrrolidone (NMP) via the conventional two‐step method, i.e., ring‐opening polycondensation forming the poly (amic acid)s and further thermal or chemical imidization forming polyimides. The inherent viscosities of the resulting polyimides were in the range of 0.79–1.13 dL/g, and most of them were soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), NMP, and tetrahydrofuran (THF), etc. Meanwhile, strong and flexible polyimide films were obtained, which had good thermal stability, with the glass transition temperatures (T_g) of 268–338°C and the temperature at 5% weight loss of 521–548°C in air atmosphere, as well as outstanding mechanical properties with tensile strengths of 89.2–112.1 MPa and elongations at break of 9.5–15.4%. The polyimides also were found to possess low dielectric constants ranging from 2.53 to 3.11. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 212–219, 2007     

Synthesis and characterization of soluble copolyimides containing chalcone and phosphine oxide moieties in the main chain

The functional diamines 3,3′‐diaminochalcone and bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide were successfully prepared by simple and convenient procedures with short reaction times, and the overall yields were 78 and 70%, respectively. Copolyimides prepared from 3,3′‐diaminochalcone, bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, and 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride exhibited excellent solubility in several organic solvents, such as dimethyl sulfoxide, N,N‐dimethylformamide, N‐methyl pyrrolidone, tetrahydrofuran, and acetone. They also showed very good thermal stability even up to 450°C for 5% weight loss (by thermogravimetric analysis) in nitrogen and a high glass‐transition temperature up to 274°C (by differential scanning calorimetry) in nitrogen. The copolymers' adhesive and photoreactive properties were also investigated, and it was confirmed that the copolyimide containing chalcone and phosphine oxide moieties in the main chain had good adhesiveness and photoreactivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Organosoluble,low‐dielectric‐constant fluorinated polyimides based on 9,9‐bis[4‐(4‐amino‐2‐trifluoromethyl‐ phenoxy)phenyl]xanthene

A new trifluoromethylated bis(ether amine) monomer, 9,9‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]xanthene (BATFPX), was prepared through the nucleophilic aromatic substitution reaction of 2‐chloro‐5‐nitrobenzotrifluoride and 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate, followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of novel fluorinated polyimides were synthesized from BATFPX with various commercially available aromatic tetracarboxylic dianhydrides by one‐step polycondensation in m‐cresol. The resulting polyimides were readily soluble in many organic solvents such as N,N‐dimethylacetamide and tetrahydrofuran, and afforded transparent, flexible and strong films with low moisture absorption (0.28–0.51%), low dielectric constant (2.85–3.26 at 1 MHz) and good optical transparency with UV‐visible absorption cut‐off wavelengths at 352–410 nm. All the polyimides were amorphous and exhibited high thermal stability, with glass transition temperatures of 282–330 °C, 5% weight loss temperatures above 520 °C in nitrogen or air and char yields higher than 55% at 800 °C in nitrogen. Also, these polyimides had good mechanical properties with tensile strengths of 93–118 MPa, elongations at break of 9–16% and initial moduli of 2.07–2.58 GPa. Copyright © 2011 Society of Chemical Industry     

Synthesis and properties of novel polyimides from 3‐(4‐aminophenylthio)‐N‐aminophthalimide

A novel, asymmetric diamine, 3‐(4‐aminophenylthio)‐N‐aminophthalimide, was prepared from 3‐chloro‐N‐aminophthalimide and 4‐aminobenzenethiol. The structure of the diamine was determined via IR and ¹H‐NMR spectroscopy and elemental analysis. A series of polyimides were synthesized from 3‐(4‐aminophenylthio)‐N‐aminophthalimide and aromatic dianhydrides by a conventional two‐step method in N,N‐dimethylacetamide and by a one‐step method in phenols. These polyimides showed good solubility in 1‐methyl‐2‐pyrrolidinone, m‐cresol, and p‐chlorophenol, except polyimide from pyromellitic dianhydride, which was only soluble in p‐chlorophenol. The 5% weight loss temperatures of these polyimides ranged from 460 to 498°C in air. Dynamic mechanical thermal analysis indicated that the glass‐transition temperatures of the polyimides were in the range 278–395°C. The tensile strengths at break, moduli, and elongations of these polyimides were 146–178 MPa, 1.95–2.58 GPa, and 9.1–13.3%, respectively. Compared with corresponding polyimides from 4,4′‐diamiodiphenyl ether, these polymers showed enhanced solubility and higher glass‐transition temperatures. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008