Swelling–deswelling behavior of poly(acrylamide‐co‐maleic acid) hydrogels

In this study the poly(acrylamide‐co‐maleic acid) hydrogels containing small amounts of maleic acid have been synthesized, and the effect of pH, ionic strength, and nature of counterions on the equilibrium water uptake has been investigated. The incorporation of small amount of maleic acid results in the transition of swelling mechanism from Fickian to non‐Fickian. The equilibrium mass swelling has been found to increase with pH of the swelling medium while increase in ionic strength causes a decrease in the swelling. The amount of maleic acid present in the hydrogel affects the swelling behavior in rather an unusual way. With lower acid contents, the equilibrium mass swelling increases while higher concentrations of maleic acid cause a decrease in the degree of swelling. The hydrogels have been found to undergo a number of swelling–deswelling cycles when pH of the swelling medium changes from 8.0 to 2.0. Hydrogels require more time to deswell compared to the time required for swelling, which has been explained on the basis of the fact that gels follow different mechanisms for the two processes. Various swelling parameters such as equilibrium mass swelling, diffusion coefficient, intrinsic diffusion coefficient, swelling exponent, etc., have been evaluated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2782–2789, 2001     

Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Frontal polymerization preparation of poly(acrylamide‐co‐acrylic acid)/activated carbon composite hydrogels for dye removal

A series of poly(acrylic acid‐co‐acrylamide) (PAA)/activated carbon (AC) composite hydrogels were rapidly prepared via frontal polymerization (FP). It was found that an increase in the concentration of AC caused an increase in the front velocity (V_f) and the highest front temperature (T_max). It may be attributed to that AC particles could increase the liquid viscosity of reaction mixture and remain the reaction heat during FP. The Fourier transform infrared and scanning electron microscopy (SEM) confirmed that AC particles had entered the hydrogel network, and many spherical AC particles with an average diameter of 0.5–1 μm had been dispersed homogeneously in the PAA hydrogel matrix. The swelling behavior showed that the equilibrium swelling values of hydrogels increased when the concentration of AC particles increased. Adsorption studies showed that incorporation of AC particles into PAA hydrogel matrix could increase the sites of interaction between the hydrogels and crystal violet molecules and result in an increase of adsorption capacities of hydrogels toward dyes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and properties of starch grafted poly[acrylamide‐co‐(acrylic acid)]/montmorillonite nanosuperabsorbent via γ‐ray irradiation technique

The novel nanosuperabsorbent copolymer (NSAP) was synthesized by grafting copolymerization of acrylamide (AM) and acrylic acid (AA) onto starch with montmorillonite (MMT) initiated using ⁶⁰Co γ‐ray irradiation. NSAP was characterized by IR spectroscopy and X‐ray diffraction (XRD). Different synthesis parameters were studied, such as AM‐to‐AA ratio, radiation total dose, radiation dose rate, crosslinker content, and clay content. NSAP can effectively improve the water retention capacity of soil. The effects of NSAP on crops were also studied, showing that NSAP has an encouraging potential for agricultural application. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1341–1346, 2005     

Encapsulation of disperse dye by phase separation technique using poly(styrene‐maleic acid)

C.I. disperse dye blue 60 was encapsulated by poly(styrene‐maleic acid) using phase separation technique, followed by the preparation of the encapsulated disperse dye dispersion. The effects of process conditions on particle size of the dispersion were investigated. The results showed that the particle size of the encapsulated disperse dye dispersion was small, and the stability was excellent when mass ratio of poly(styrene‐maleic acid) to disperse dye (R_p/d), dropping speed of phase separation agent (D_s), disperse dye content in dispersion (C_d), and dispersing time (D_t) were about 20%, 7 mL/min, 5–7.5%, and 1.5 h, respectively. Transmission electron microscope (TEM), zeta potentials, and contact angle indicated that C.I. disperse dye blue 60 was successfully encapsulated by poly(styrene‐maleic acid). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) reinforced by poly(lactic acid) fibers

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) (PBSA) reinforced by poly(lactic acid) (PLA) fibers were developed by hot compression and characterized by Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analyzer, and tensile testing. The results show that PBSA and PLA are immiscible, but their interface can be improved by processing conditions. In particular, their interface and the resulting mechanical properties strongly depend on processing temperature. When the temperature is below 120 °C, the bound between PBSA and PLA fiber is weak, which results in lower tensile modulus and strength. When the processing temperature is higher (greater than 160 °C), the relaxation of polymer chain destroyed the molecular orientation microstructure of the PLA fiber, which results in weakening mechanical properties of the fiber then weakening reinforcement function. Both tensile modulus and strength of the composites increased significantly, in particular for the materials reinforced by long fiber. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43530.     

Evaluation of toughening mechanisms of polypropylene/ethylene–octene copolymer/maleic anhydride‐grafted poly(ethylene‐co‐octene)/clay nanocomposite

The toughness of a polypropylene (PP)/ethylene‐octene copolymer (EOC)/maleic anhydride‐grafted poly(ethylene‐co‐octene) (EOC‐g‐MA)/clay nanocomposite and blends of PP/EOC and PP/EOC/EOC‐g‐MA was investigated using Charpy impact and single‐edge‐notch tensile (SENT) tests. In order to understand the toughening mechanisms, impact fracture surfaces and damage zones of single‐edge‐notch samples were studied with scanning electron microscopy and transmission optical microscopy, respectively. It was observed that the addition of EOC‐g‐MA to PP/EOC blend led to improvements in both impact strength and fracture energy of SENT tests because of the enhanced compatibility of the blend, which resulted from reduced EOC particle size and improved interfacial adhesion, and the decreased crystallinity of PP. The incorporation of clay to PP/EOC/EOC‐g‐MA blend caused a further increase of the toughness, owing to the greater decrease in the size of elastomer particles, to the presence of clay tactoids inside the elastomer phase and presumably to debonding of clay layers during the low‐speed SENT tests. The results of microscopic observations showed that the main toughening mechanism in PP/EOC/EOC‐g‐MA blend and PP/EOC/EOC‐g‐MA/clay nanocomposite is crazing. Copyright © 2012 Society of Chemical Industry     

Sorption properties of poly(styrene‐co‐divinylbenzene) amine functionalized weak resin

The poly(styrene‐co‐divinylbenzene) amine functionalized weak resin was studied as adsorbent of heavy metal ions from an aqueous solution by using the Batch equilibrium procedure. The resin adsorbed Hg(II) 56% (0.56 mEq/g) at pH 2, and 45% (1.13 mEq/g) of U(VI), 38% (0.36 mEq/g) of Pb(II) at pH 5 from an aqueous solution containing 1 g/L of each metal ion. It did not adsorb Cd(II), Zn(II). The equilibrium time was achieved during the first hour. The maximum load capacity for Hg(II) was 0.8 mEq/g (75 mg)/g dry resin. It is possible to recover around 60% of the resin after the treatment with 1–4 M HClO₄ and HNO₃ of the loaded Hg(II) resin. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2123–2127, 2001     

Poly(acrylic acid‐co‐acrylamide‐co‐2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid)‐grafted nanocellulose/poly(vinyl alcohol) composite for the in vitro gastrointestinal release of amoxicillin

Superabsorbent polymer composites (SAPCs) are very promising and versatile materials for biomedical applications. This study concentrates on the development of novel cellulose‐based SAPC, Poly(acrylic acid‐co‐acrylamide‐co?2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid)‐grafted nanocellulose/poly(vinyl alcohol) composite, P(AA‐co‐AAm‐co‐AMPS)‐g‐NC/PVA, as a potential drug delivery vehicle. Amoxicillin was selected as a model drug, which is used for the treatment of Helicobacter pylori induced peptic and duodenal ulcers. P(AA‐co‐AAm‐co‐AMPS)‐g‐NC/PVA was synthesized by graft copolymerization reaction, and FTIR, XRD, SEM, and DLS analyses were performed for its characterization. Equilibrium swelling studies were conducted to evaluate the stimuli‐response behavior of the SAPC and found that equilibrium swelling was dependent on pH, contact time, temperature, ionic strength, concentration of crosslinker and PVA. Maximum drug encapsulation efficiency was found out by using different concentrations of amoxicillin. Drug release studies were carried out at simulated gastric and intestinal fluids and the release % was observed as maximum in intestinal fluids within 4 h. The drug release kinetics was investigated using Peppas' potential equation and follows non‐Fickian mechanism at pH 7.4. Thus, the drug release experiments indicate that P(AA‐co‐AAm‐co‐AMPS)‐g‐NC/PVA would be a fascinating vehicle for the in vitro administration of amoxicillin into the gastrointestinal tract. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40699.     

Fire retardancy and durability of poly(N‐benzyloxycarbonyl‐3,4‐dihydroxyphenylalanine)‐montmorillonite composite film coated polyimide fabric

Polyimide (PI) fabric was coated with composite films composed of poly(N‐benzyloxycarbonyl‐3,4‐dihydroxyphenylalanine) (PNBD) and montmorillonite (MMT), prepared via layer‐by‐layer assembly. Three coating recipes (changed by altering the concentration of PNBD solution) were used to study the growth of thin films. Scanning electron microscope showed that, after 20 times standard washing, PNBD‐MMT film still coated on PI fiber, while MMT film coated on PI had been almost washed off. Thermogravimetric analysis indicated that, in nitrogen atmosphere at 900°C, the residue of uncoated PI was 36.62%, after 20 times standard washing, residue of PNBD‐MMT coated PI (53.80%) was higher than that of MMT coated PI (50.08%). Vertical flame testing showed that the burning length of PNBD‐MMT coated PI (7 mm) was much shorter than that of uncoated PI (30 mm) and MMT coated PI (17 mm) after 20 times standard washing. These results demonstrated the excellent flame retardancy and durability of PNBD‐MMT film coated PI fabric. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39608.     

Poly(ethylene terephthalate)/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate)/clay nanocomposites: Effects of biaxial stretching

In this study, we fabricated poly(ethylene terephthalate) (PET)/clay, PET/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate) (PETG), and PET/PETG/clay nanocomposite plates and biaxially stretched them into films by using a biaxial film stretching machine. The tensile properties, cold crystallization behavior, optical properties, and gas and water vapor barrier properties of the resulting films were estimated. The biaxial stretching process improved the dispersion of clay platelets in both the PETG and PET/PETG matrices, increased the aspect ratio of the platelets, and made the platelets more oriented. Thus, the tensile, optical, and gas‐barrier properties of the composite films were greatly enhanced. Moreover, strain‐induced crystallization occurred in the PET/PETG blend and in the amorphous PETG matrix. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42207.     

Sorption of dye wastes by poly(vinyl alcohol)/poly(carboxymethyl cellulose) blend grafted through a radiation method

The instability in water of poly(vinyl alcohol) (PVA)/poly(carboxymethyl cellulose) (CMC) was improved through radiation-induced grafting with a styrene monomer. The PVA/CMC blend graft copolymer was used as a sorbent for dye wastes normally released from textile factories. The factors that may affect the sorption process such as time, temperature, weight of the blend graft copolymer, and volume of the dye waste were investigated. The sorption of dyestuffs by the blend graft copolymer was determined by a method based on spectroscopic analysis. The results showed that the blend graft copolymer has a high affinity for basic, acid, and reactive dyes. Meanwhile, it was observed that the sorption of dyes is more effective at the high temperature of 70^oC. Moreover, it was found that the sorption of dyes depends on the weight of the blend graft copolymer and does not depend on the volume of the waste solution. The sorption of the dyestuffs by a PVA/CMC graft copolymer may be considered to be a practical method to remove organic pollutants. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 136–142, 2001     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Lignocellulosic flour‐reinforced poly(hydroxybutyrate‐co‐valerate) composites

Residual lignocellulosic flour from spruce and ground olive stone was used as a natural filler in poly(hydroxybutyrate‐co‐valerate) (PHBV)‐based composites. The morphology and the thermal properties of these composites were investigated by scanning electron microscopy and differential scanning calorimetry, respectively. Lignocellulosic fillers acted as nucleating sites for the crystallization of PHBV and strongly enhanced its degree of crystallinity. Dynamic mechanical analysis and tensile properties of these materials were also studied. A significant reinforcing effect was displayed by dynamic mechanical analysis at temperatures higher than the glass–rubber transition of the matrix. In addition, for low‐particle‐size spruce, a stabilization of the modulus was observed up to 500 K. High‐strain tensile properties did not show any reinforcing effect. This apparent disagreement was explained by the poor adhesion between the hydrophilic lignocellulosic filler and the hydrophobic polymeric matrix. To validate this hypothesis, the experimental data were compared with predicted data involving the percolation concept. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1302–1315, 2003     

Mechanical properties of acrylonitrile–butadiene–styrene copolymer/poly(l‐lactic acid) blends and their composites

As the material properties of acrylonitrile–butadiene–styrene copolymer (ABS) have an excessively wide margin for applications in automobile console boxes, ABS partly replaced with poly(l ‐lactic acid) (PLA) may be used for the same purpose with improved ecofriendliness if the corresponding deterioration of the material properties is acceptable through the choice of appropriate additives. ABS composites with 30 wt % renewable components (PLA and cellulose pulp) were prepared by melt compounding, and the material properties were examined as a function of the additive content. The changes in the mechanical properties of the ABS/PLA blends were examined after the addition of cellulose pulp and two clays [Cloisite 25A (C25A) and sodium montmorillonite] as well as these two clays treated with bis(3‐triethoxysilylpropyl)tetrasulfide (TESPT). The heat distortion temperatures of the composites were measured as a function of the content of the TESPT‐treated C25A. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40329.     

Modification of poly(3‐hydroxybutyrate)‐co‐poly(3‐hydroxyvalerate) with natural rubber

Composites of poly(3‐hydroxybutyrate)‐co‐poly(3‐hydroxyvalerate) (PHBHV) with 6% of 3‐hydroxyvalerate (HV) and natural rubber (NR) were prepared by a solvent‐casting method. Different approaches were tested for the composite preparation. Both PHBHV and NR were dissolved in chloroform, followed by its evaporation, giving various layers. The mechanical properties and morphology of the obtained composites were evaluated by tensile tests and scanning electron microscopy (SEM), respectively. The obtained results demonstrated that the final composite has excellent mechanical properties when compared with PHBHV. SEM analysis unequivocally showed the excellent adhesion between the two polymeric layers. This new material was also tested as a drug delivering system using flurbiprofen as a model drug, and then the diffusion coefficients were determined. This article describes an easy method to produce a desirable composite from PHBHV and NR. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Alternative procedure for the incorporation of quantum dots into poly(N‐isopropyl acrylamide‐co‐acrylic acid) microgels based on multiple interactions

Monodisperse fluorescent poly(N‐isopropyl acrylamide‐co‐acrylic acid) microgels doped with quantum dots (QDs) were fabricated as follows. First, cysteamine‐capped cadmium telluride (CA–CdTe) QDs were introduced into the microgels at pH 7 by electrostatic interactions. Afterward, the CA–CdTe QDs were further immobilized in the microgels by the collapse of the polymer network when the pH of solution was adjusted to 4. In this system, there existed multiple interactions between the CA–CdTe QDs and the microgels, including hydrogen bonds, electrostatic interactions, and coordination bonds. The photoluminescence intensity and maximum emission wavelength of the resulting microgels could be easily adjusted by changes in the content of the CA–CdTe QDs in the hybrid microgels (HMs) and with differently sized QDs, respectively. We found that the lower the addition of CA–CdTe QDs was, the bigger the blueshift of the photoluminescence spectra of the HMs was and the weaker the photoluminescence intensity was. Finally, temperature‐responsive emission of the HMs was examined. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43227.     

PTCR characteristics of poly(styrene‐co‐acrylonitrile) copolymer/stainless steel powder composites

Positive temperature coefficient of resistivity (PTCR) characteristics of poly(styrene‐co‐acrylonitrile) copolymer (SAN)/stainless steel (SS) powder (80 wt %) composites prepared by melt‐mixing method has been investigated with reference to SAN/carbon black (CB) composites. The SAN/CB (10 wt %) composites showed a sudden rise in resistivity (PTC trip) at 125°C, above the glass transition temperature (T_g) of SAN (T_g ≈ 107°C). However, the PTC trip temperature of SAN/SS (80 wt %) composites appeared at 94°C, well below the T_g of SAN. Addition of 1 phr of nanoclay increased the PTC trip temperature of SAN/CB (10 wt %) composites to 130°C, while SAN/SS (80 wt %)/clay (1 phr) nanocomposites showed the PTC trip at 101°C. We proposed that the mismatch in coefficient of thermal expansion (CTE) between SAN and SS played a key role that led to a disruption in continuous network structure of SS even at a temperature below the T_g of SAN. The dielectric properties study of SAN/SS (80 wt %) composites indicated possible use of the PTC composites as dielectric material. DMA results showed higher storage modulus of SAN/SS composites than the SAN/CB composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical properties of poly(N‐isopropyl‐acrylamide‐co‐itaconic acid) hydrogels

Hydrogels of N‐isopropylacrylamide and itaconic acid were synthesized with different monomer ratios and with two crosslinking agent concentrations. The different xerogels were immersed in water and the swelling process was conducted up to equilibrium conditions at two temperatures (22 and 37°C). These temperatures are lower and higher than the transition temperature shown by PNIPA hydrogels. The mechanical properties of the different solvated hydrogels were examined by oscillatory shear measurements at 22 and 37°C. The copolymer volume fraction and the elastic storage modulus of the hydrogels decreased as the itaconic acid percentage in the copolymer increased. This behavior was attributed to the higher hydrophilic character of the itaconic acid comonomer. Effective crosslinking density, molar mass between crosslinks, and the polymer–solvent interaction parameter were determined from the experimental values of the elastic storage moduli and the copolymer volume fractions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2540–2545, 2002     

Hydrogel composites based on linear low‐density polyethylene‐g‐poly (acrylic acid)/Kaolin or halloysite nanotubes

Two series of superabsorbent hydrogel composites were prepared using waste linear low‐density polyethylene, acrylic acid, and two types of clays including kaolin and halloysite nanotube (HNT) through emulsion polymerization. The effects of the clay content on Water absorbency were investigated to obtain a high swelling capacity. The prepared samples were characterized using FTIR, SEM, thermogravimetric analysis, XRD, solid‐state ¹³C Nuclear Magnetic Resonance spectroscopy, and ²⁹Si NMR. SEM characterization of the samples showed that the hydrogel composites have more pores and a higher swelling ratio than the clay‐free hydrogels. The hydrogel composite containing kaolin had higher water absorbency compared to the hydrogel composites with HNT. The swelling behavior of the hydrogel composite was investigated in various saline solutions. The hydrogel composite containing 5 wt % kaolin had the highest water absorbency (760 g/g in distilled water). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40101.