Effect of filler surface treatment on mechanical properties and thermal properties of single and hybrid filler–filled PP composites

The influence of two types of surface treatments (aminosilane and Lica‐12) on the mechanical and thermal properties of polypropylene (PP) filled with single and hybrid filler (silica and mica) was studied. An improvement in tensile properties and impact strength was found for both treatments compared to those of untreated composites. However, the filler with silane coupling agent showed better improvement compared to the filler with Lica‐12 coupling agent. This was due to better adhesion between filler and matrix. Thermal analysis indicates that surface treatments increased the nucleating ability of filler, but decreased the coefficient of thermal expansion of PP composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and mechanical properties of dual‐curable epoxyacrylate hybrid composites

A dual‐curable epoxyacrylate (EA) oligomer with one epoxide group and one vinyl group at each end was synthesized for the application as adhesive sealant in the liquid crystal display panels. However, after UV and thermal cure, the EA resin was brittle with a poor resistance to crack initiation and propagation. Liquid rubbers with different functional end groups were thus tried as toughening agents for the EA resin. Among all the rubber‐toughened EAs, the EA‐V5A5 added with vinyl‐terminated and amino‐terminated butadiene‐acrylonitrile copolymers (VTBN and ATBN) each at 5 phr had the highest fracture toughness, tensile strength, and elongation at break but a lower initial modulus. To raise the modulus, submicron‐sized silica particles (∼170 nm) with surface vinyl functional groups were further added to the EA‐V5A5 to prepare the hybrid composites. Because of interfacial chemical bonding provided by the surface vinyl functional groups, both modulus and fracture toughness were increased by adding silica particles, without any appreciable decrease in extensibility. For the hybrid composite at 20 phr silica particles, the initial modulus, fracture toughness, and fracture energy were raised by 10.3, 100, and 267%, respectively, when compared to the neat epoxyacrylate. Owing to their strong interfacial bonding, the increase of fracture toughness was mainly due to the crack deflection and bifurcation on silica particles, in addition to the rubber particle bridging and tearing as evidenced by SEM pictures on the fracture surface. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41820.     

Effect of quasi‐carbonization processing parameters on the mechanical properties of quasi‐carbon/phenolic composites

In this work, quasi‐carbon fabrics were produced by quasi‐carbonization processes conducted at and below 1200°C. Stabilized polyacrylonitrile (PAN) fabrics and quasi‐carbon fabrics were used as reinforcements of phenolic composites with a 50 wt %/50 wt % ratio of the fabric to the phenolic resin. The effect of the quasi‐carbonization process on the flexural properties, interfacial strength, and dynamic mechanical properties of quasi‐carbon/phenolic composites was investigated in terms of the flexural strength and modulus, interlaminar shear strength, and storage modulus. The results were also compared with those of a stabilized PAN fabric/phenolic composite. The flexural, interlaminar, and dynamic mechanical results were quite consistent with one another. On the basis of all the results, the quasi‐static and dynamic mechanical properties of quasi‐carbon/phenolic composites increased with the applied external tension and heat‐treatment temperature increasing and with the heating rate decreasing for the quasi‐carbonization process. This study shows that control of the processing parameters strongly influences not only the mechanical properties of quasi‐carbon/phenolic composites but also the interlaminar shear strength between the fibers and the matrix resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Size effect of charcoal particles on the properties of bamboo charcoal/ultra‐high molecular weight polyethylene composites

This study was aimed at examining the size effect of charcoal particles on the properties of bamboo charcoal (BC)/ultra‐high molecular weight polyethylene (UHMWPE) composites. Four types of BC with various particle sizes were mixed with UHMWPE using a twin‐screw extruder. It was found that the melting temperature and crystallinity of the composites were slightly decreased with the addition of BC. The incorporation of BC remarkably improved the tensile properties and creep resistance of UHMWPE, and the particle size of BC strongly affected the properties of BC/UHMWPE composites. The BC with lowest particle size exhibited best reinforcement, where the tensile strength and Young's modulus were increased by 385% and 517% compared with neat UHMWPE. The composites with 70 wt % BC possessed conductivities of 16.8, 14.1, 13.5, and 10.9 S/m. The storage modulus and glass transition temperature of the composites also increased with the addition of BC. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45530.     

The mechanical and tribological properties of nitric acid‐treated carbon fiber‐reinforced polyoxymethylene composites

The carbon fibers have been exposed to nitric acid oxidation treatments and introduced into polyoxymethylene composites (POM/CF). The nitric acid treatment increases the number of the flaws, roughness of the surface, and disorder of carbon atoms on fiber, as well as introduces reactive functional groups, which could lead to a better mechanical bonding between fiber and the matrix. It is shown that the impact strength and fiber‐matrix adhesion in composites (POM/mCF) are superior to those for POM/CF composites. Simultaneously, the addition of mCF improves flexural strength and modulus relative to virgin POM significantly. Average friction coefficient values of POM/CF composites are lower than that of POM/mCF composites. As the percentage of fiber increases, the trend of wear ratio of the composites goes down initially and bumps up afterwards. The results indicate that the proper contents of CF and mCF in composites range from 5 wt % to 20 wt %. Scanning electron microscopy of worn surface morphology has revealed that the main wear mechanism of the composites were adhesive wear and ploughing wear. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41812.     

Thermal and mechanical properties of polypropylene/wood‐flour composites

In this research, polypropylene/wood‐flour composites (WPCs) were blended with different contents of wood and/or maleated polypropylene (MAPP) and clay. We found that the addition of MAPP or clay in the formulation greatly improved the dispersion of the wood fibers in the composite; this suggested that MAPP or clay may have played the role of an adhesion promoter in the WPCs. The results obtained with clay indicate that it also acted as a flame retardant. The thermal tests carried out with the produced samples showed an increased crystallization temperature (T_c), crystallinity, and melting temperature (T_m) with wood loading. The increase of the two former parameters was explained by the incorporation of wood flour, which played the role of nucleating agent and induced the crystallization of the matrix polymer. On the other hand, the T_m increase was ascribed to the insulating properties of wood, which hindered the movement of heat conduction. The effects of UV irradiation on T_m and T_c were also examined. T_c increased with UV exposure time; this implied that UV degradation generated short chains with low molecular weight that could move easily in the bulk of the sample and, thus, catalyze early crystallization. The flexural strength and modulus increased with increasing wood‐flour content. In contrast, the impact strength and tensile strength and strain decreased with increasing wood‐flour content. All of these changes were related to the level of dispersion of the wood flour in the polymeric matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preferred orientation of chopped fibers in polymer-based composites processed by selective laser sintering and fused deposition modeling: Effects on mechanical properties

The orientation of reinforcing fibers in polymer-based composites greatly affects their mechanical features. It is known that different orientations of continuous fibers in the stacked layers of a laminate play a crucial role in providing an isotropic mechanical behavior, while the alignment of chopped fibers in injection molding of composites results in a degree of anisotropy. Recent additive manufacturing techniques have offered a way of controlling the fiber orientation. This article aims to investigate the effect of fiber orientation on the mechanical properties of polyamide/carbon fiber composites processed by fused deposition modeling and selective laser sintering. Tensile samples which had different fibers and layer interface with respect to the sample axis (and therefore to the tensile load) were produced. Tensile tests were performed at different strain rates; the tensile properties and the fracture surface morphology were correlated with the processing method and the sample microstructure. The best strength and stiffness were observed when the fibers and the layer interfaces were parallel to the sample axis.     

Flame‐retardant and mechanical properties of rigid polyurethane foam/MRP/mg(OH)2/GF/HGB composites

Some rigid polyurethane foam (RPUF) composites modified with microencapsulated red phosphorus (MRP), magnesium hydrate (Mg(OH)₂), glass fiber (GF), and hollow glass bead (HGB) were prepared. The influence of the MRP, Mg(OH)₂, GF, and HGB on the flame‐retardant, combustion, and mechanical properties of the filled RPUF composites was investigated. The results showed that the flame‐retardant and the combustion properties of the composites were obviously improved, the limiting oxygen index, half burning time and the residual mass/original mass ratio increased with increasing MRP/Mg(OH)₂ weight fraction, especially in case of MRP/Mg(OH)₂ weight fraction of 8 wt %; the carbon monoxide (CO) concentration decreased with increasing MRP/Mg(OH)₂ weight fraction, When the composites were loaded appreciate content of the HGB and the GF, the maximum torque and compressive strength of the composites were improved. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46551.     

Effect of hybrid hollow microspheres on thermal insulation performance and mechanical properties of silicone rubber composites

Hollow microspheres (HM) of ceramic, silica, and glass‐filled silicone rubber (SR) composites were prepared, and the effects of hybrid HM on thermal and mechanical properties of composites were investigated. The results indicate that hybrid HM can effectively improve the thermal insulation property of HM/SR composites. Especially, for sample 15S, the thermal conductivity and thermal degradation temperature reached 0.1273 W/m K and 521 °C (45 °C higher than that of neat SR), respectively. Besides, thermal insulation performance was improved, showing as a temperature of 103.2 °C after 15 min heating, which is 37.8 °C lower than that of SR. The tensile strength of composites was enhanced from 1.92 MPa at 11.56 vol % hollow silica microspheres (HSM) loading to 3.08 MPa at 21.88 vol % HSM loading. Moreover, the compressive strength was improved from 3.33 to 5.68 MPa by introducing more hollow ceramic microspheres into the matrix, in this case, from 7.79 to 15.33 vol %. Furthermore, the failure mechanism was analyzed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46025.     

Effect of structure on mechanical properties of vinyl ester resins and their glass fiber‐reinforced composites

The article describes the effect of structure of vinyl ester resins (VE) on the mechanical properties of neat sheets as well as glass fabric‐reinforced composites. Different samples of VE were prepared by reacting ester of hexahydrophthalic anhydride (ER) and methacrylic acid (MAA) (1 : 1 molar ratio) followed by reaction of monomethacrylate terminated epoxy resin with glutaric (E) or adipic (F) or sebacic acid (G) (2 : 1 molar ratio). The neat VE were diluted with styrene and sheets were fabricated by using a glass mold. A significant reduction in the mechanical properties was observed by increasing the methylene content of resin backbone (i.e., sample E to G). Glass fabric‐reinforced composites were fabricated by vacuum assisted resin transfer molding (VARTM) technique. Resin content in the laminates was 50 ± 5 wt %. Increase in the number of methylene groups in the vinyl ester resin (i.e., increasing the bridge length) did not show any significant effect on limiting oxygen index (LOI) value (21 ± 1) of the laminates but tensile strength, tensile modulus, flexural strength, and flexural modulus all increased though these values are significantly lower than observed in laminates based on resin B. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nano/micro ternary composites based on PP,nanoclay, and CaCO3

Nano‐/microcomposites based on polypropylene/montmorillonite/calcium carbonate were prepared by melt mixing. Their structures and properties were characterized by small‐angle X‐ray diffraction, thermal analysis, and rheological measurements. The intercalation degree was found to be dependent on the compatibilizer content and the processing temperature. The addition of the organoclay slightly increased the melt crystallization temperature of polypropylene, acting as nucleating agents, and improved the degree of crystallinity. The rheological tests showed that nanocomposites increased the complex viscosity when compared with the microcomposites with the same filler content and exhibited a pronounced shear‐thinning behavior in the low frequency range. A Carreau‐Yasuda model was used to model the rheological behavior of these materials. The nano‐/microcomposites showed a significant improvement (about 50%) of the Young's modulus when compared with microcomposites with the same filler content due to the intercalation or exfoliation of the organoclay and the enhanced degree of crystallinity. Moreover, some formulations showed an enhancement of elongation at break and ultimate strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

X‐ray irradiated LDPE/PP blends with high mechanical and dielectric performance

In this study, the influences of polypropylene (PP) additive (varying from 20% to 80% wt) and low dose X‐ray irradiation (changing from 25 to 100 Gy) on the mechanical and dielectric properties of low‐density polyethylene (LDPE) were investigated. LDPE/PP film blends were prepared by hot press technique. While the highest Young modulus and tensile strength were observed for the 20%LDPE/80%PP blend at 25 Gy X‐ray irradiation, the same blend had the highest energy at break and percentage strain at break values for 50 Gy X‐ray exposure. These results also indicated a chain scission in the material. The differential scanning calorimetry curves also indicated a chain scission and crosslinking effects in the blends due to X‐ray irradiation. Hence, the higher concentration of PP additive and exposure of low dose X‐ray resulted in a polymer composite with high mechanical performance. On the other hand, the dielectric investigations revealed that the 25 Gy X‐ray irradiated 20%LDPE/80%PP blend may also attract attention for capacitor applications due to its increased static dielectric constant and reduced dielectric loss. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46571.     

Effect of starch predrying on the mechanical properties of starch/poly(ε‐caprolactone) composites

This study describes the effect of predrying sago starch, a tropical starch, on the resultant mechanical properties of starch/poly(ε‐caprolactone) composite materials. Sago starch was dried to less than a 1% moisture level in a vacuum oven and dispersed into a polycaprolactone matrix with an internal mixer at 90°C. The mechanical properties of the composite were studied according to methods of the Association for Standards, Testing, and Measurement, whereas the morphology was monitored with scanning electron microscopy. The properties were compared with a composite obtained with native starch containing 12% moisture. The results indicated that predrying the starch led to a lower property drop rate in the composite as the starch content increased. The elastic modulus, tensile strength, and elongation at break were higher than those obtained when starch was used without predrying. The morphology observed during scanning electron microscopy studies was used to explain the observed trends in the mechanical properties. In this way, a relatively simple and cost‐effective method was devised to increase the starch loading in the polycaprolactone matrix to obtain properties within the useful range of mechanical properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 877–884, 2003     

Synthesis of hybrid ZnO/CNTs nanoparticles and their reinforcement in nylon‐6 polymer fibers

In this investigation, in situ synthesis of zinc oxide nanoparticles in the presence of multiwalled carbon nanotubes (CNTs) have been carried out using a sonochemical technique. Zinc(II)acetate was used as a source of ZnO in the presence of ethylene glycol (EG) to obtain zinc oxide (ZnO) nanoparticles. The synthesized hybrid ZnO/CNTs nanoparticles were used as reinforcements to enhance the mechanical, thermal and UV absorbing properties of Nylon‐6 composite fibers. The polymer nanocomposites (PNC) were fabricated by dry mixing Nylon‐6 polymer powder with the ZnO/CNTs hybrid nanoparticles as the first step, then followed by the drying and melt extrusion process of fiber materials in a single‐screw extruder. The extruded fibers were stretched and stabilized using a godet set‐up and wound on a Wayne filament winder machine. The hybrid ZnO/CNTs infused Nylon‐6 composite fibers were compared with commercial ZnO, CNTs infused Nylon‐6 composite fibers and neat Nylon‐6 fibers for their structural and thermal properties. The morphological characteristics of ZnO/CNTs nanoparticles were carried out using X‐ray diffraction and transmission electron microscopy (TEM) techniques. The Nylon‐6 PNC fibers which were of ～80 μ size were tested mechanically. The tensile tests revealed that failure stress of the 1% infused ZnO/CNTs Nylon‐6 PNC fibers is about 73% higher than the neat extruded Nylon‐6 fiber and the improvement in the tensile modulus is 377.4%. The DSC results show an increase in the glass transition temperature and crystallization for ZnO/CNTs infused Nylon‐6 PNC fibers. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of different surface treatments on polypropylene composites reinforced with yerba mate fibers: Physical,mechanical, chemical,and morphological properties

This study presents the preparation of post-consumer polypropylene (r-PP) composites filled with 30 wt% yerba mate (YM) stick particles. To improve the fiber–matrix adhesion, three surface treatments were performed: alkaline treatment with sodium hydroxide (NaOH) and use of 3-aminopropyltriethoxysilane (APTS) and maleic anhydride graft polypropylene copolymer (PP-g-MA) as coupling agents. Mechanical properties including tensile, flexural, and impact resistance were determined, and chemical (Fourier transform infrared spectroscopy [FTIR]), physical (water absorption), and morphological analyses were performed. The main findings show that the treatments were efficient in improving the mechanical properties of the composites, with emphasis on the r-PP/YM30/APTS and r-PP/YM30/PP-g-MA composites, which proved to be superior in tensile, flexion and impact strength and absorption of water compared to the untreated composite. The morphological analysis showed a better interaction between the fiber and the polymeric matrix for the composites with YM/APTS and YM/PP-g-MA, which corroborates the results of tensile and flexural strength, as well as with the spectra of FTIR in which the chemical modification of the fibers is observed. However, the results show that these treatments are promising in obtaining composites with recycled matrix with better properties.     

Mechanical and water absorption behaviors of corn stalk/sisal fiber‐reinforced hybrid composites

In this study, corn stalk flour (CSF) was used as filler instead of wood flour (WF) to prepare poly(vinyl chloride) (PVC) based wood plastic composite (WPC). In order to enhance the mechanical properties of the WPC, sisal fiber (SF) was introduced as reinforcer. The mechanical and the water absorption behaviors of WPC were investigated in detail. The results indicated that the chemical structure of CSF proved by FTIR was similar to that of WF. The effect of the hybridization of SF and CSF on the mechanical and water absorption behaviors of CSF/SF/PVC composite was studied. It was found that the introduction of SF of 5 mm in length resulted in improvement of the mechanical properties and had little effect on water absorption behavior. Scanning electron microscopy was carried out to observe the fracture surface of the composite. The distribution of CSF and SF in PVC was analyzed. Meanwhile, the hybrid enhancement mechanism of SF in PVC matrix was discussed. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46405.     

Tribological and mechanical properties of carbon‐nanofiber‐filled polytetrafluoroethylene composites

The effects of various filler concentrations (0.1, 0.5, 1, 1.5, 2, 2.5, and 3 wt %) on the tribological and mechanical properties of carbon‐nanofiber (CNF)‐filled polytetrafluoroethylene (PTFE) composites were studied. Moreover, the influence of various loads (50, 100, 150, and 200 N) and sliding velocities (0.692 and 1.39 m/s) on the friction and wear behaviors of the PTFE composites was investigated. The results showed that the friction coefficients of the PTFE composites decreased initially up to a 0.5 wt % filler concentration and then increased, whereas the antiwear properties of the PTFE composites increased by 1–2 orders of magnitude in comparison with those of pure PTFE. The composite with a 2 wt % filler concentration had the best antiwear properties under all friction conditions. The friction coefficients of the CNF/PTFE composites decreased with increases in the load and sliding velocity, whereas the wear volume loss of the PTFE composites increased. At the same time, the results also indicated that the mechanical properties of the PTFE composites increased first up to a 1 wt % filler concentration and then decreased as the filler concentration was increased above 1 wt %. In comparison with pure PTFE, the impact strength, tensile strength, and elongation to break of the PTFE composites increased by 40, 20, and 70%, respectively, at a 1 wt % filler concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2430–2437, 2007     

Effect of chemical treatments on the mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

This study was performed with commercially available phenyl trimethoxysilane (PTMS) and neoalkoxytitanate [i.e., neopentyl(diallyl)oxytri(dioctyl)phosphato titanate (LICA 12)] as coupling agents. PTMS and LICA 12 were used to treat talc and kaolin to compare their effects with untreated fillers upon incorporation into polypropylene (PP). Single‐filler PP composites (containing either talc or kaolin) and hybrid‐filler composites (containing a mix of both talc and kaolin) were compounded in a twin‐screw extruder and subsequently injection‐molded into dumbbells. The incorporation of PTMS and LICA 12 slightly decreased the tensile and flexural properties in terms of modulus and strength but increased the elongation at break for both single‐filler and hybrid‐filler composites. There was also a significant improvement in the impact strength of the composites, particularly those treated with LICA 12. The hybrid composites, through the synergistic coalescence of positive characteristics from talc and kaolin with the aid from chemical treatment provided an economically advantageous material with mechanical properties comparable to those of the single‐filler‐filled PP composites. Further investigations on flow and morphological properties were also done to correlate the mechanical properties of the single‐ and hybrid‐filler‐filled PP composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008