高锰奥氏体低温钢力学性能及Hall-Petch关系的研究

高锰奥氏体低温钢作为一种经济型低温钢材料,具有非常巨大的发展空间.为进一步研究晶粒尺寸对高锰奥氏体低温钢的影响,本文对其进行了不同工艺的固溶处理,测试了不同晶粒尺寸实验钢的室温拉伸及低温冲击性能, 通过扫描电镜(SEM)、背散射电子衍射(EBSD)等方法进行表征并计算其Hall-Petch关系式.-196 ℃冲击实验结果表明,高锰奥氏体低温钢拥有良好而稳定的超低温冲击性能,且其超低温冲击性能不随晶粒尺寸的增加而发生变化.经计算实验钢屈服强度所对应的Hall-Petch常数K_y为7.27 MPa·mm^0.5,明显小于其他被研究的奥氏体高锰钢.进一步计算拉伸过程中不同真应变ε对应的Hall-Petch常数K(ε),发现在拉伸过程中,受TWIP效应产生的变形孪晶影响,K(ε)值随应变量的增加而增加;当真应变达到0.3时,组织内变形孪晶不再继续生成,加工硬化过程不再进行,K(ε)也达到极大值.     

The effect of niobium on the microstructure of ferritic stainless steel

The effect of different amounts of Nb and of homogenization on the ferritic stainless steels containing 17–18 wt.% Cr was investigated with scanning electron microscopy (SEM), optical microscopy, energy-dispersive spectrometry (EDS), X-ray diffraction (XRD) and differential thermal analysis (DTA). It was observed that M₂₃C₆, NbC and sigma phase formed in these steels. In addition, the formation of Nb₂C was observed in the sample containing 3.0 wt.% Nb. While the amount of Nb increased from 0.5 to 3.0 wt.% Nb, the microhardness of the matrix and the amount of M₂₃C₆ decreased and the toughness of the samples increased. After homogenization, the increase in the toughness of the samples containing 1.5–3.0 wt.%Nb was considerable and impressive.     

On the variation of grain size and fractal dimension in an austenitic stainless steel

Samples of an AISI type 316L stainless steel were subjected to different treatments to promote changes in their microstructure. The specimens were heated in a box furnace set at four different temperatures for 30 min and cooled in air to room temperature by placing them in water after the cycle was completed. The samples were prepared following standard metallographic procedures, the microstructure was revealed with an electrolytic etchant, and the average grain size in each sample was determined by the mean line intercept technique. Images from the microstructures were digitized and fed into a personal computer for their fractal analysis by box counting. Two different approaches were used to obtain the fractal dimension of the structure, yielding to similar values in both cases. It was found that the fractal dimension of the microstructure increased with the reduction in grain size.     

Mechanical properties characterisation of welded joint of austenitic stainless steel using instrumented indentation technique

The instrumented indentation test is a promising nondestructive technique for evaluating mechanical properties of metallic materials. In this study, the localised mechanical properties of welded joint of 304 austenitic stainless steel were characterised with the instrumented indentation test. The single V-groove welded joint was produced using the electric arc welding. A series of instrumented indentation tests were carried out at different regions, including base material, weld zone and heat-affected zone (HAZ). A soft zone regarding strength properties was found in the coarse-grain HAZ. The results show that the HAZ has the lowest yield strength and tensile strength (263.6 MPa, 652.5 MPa) compared with the base material (307.4 MPa, 807.9 MPa) and the weld zone (285.6 MPa, 702.1 MPa). In addition, characterisations of microstructure, microhardness and conventional tensile tests have been performed for comparison. The results reveal that the localised mechanical properties of welded joint of austenitic stainless steel can be represented effectively with the instrumented indentation technique.     

Parylene coatings on stainless steel 316L surface for medical applications — Mechanical and protective properties

The mechanical and protective properties of parylene N and C coatings (2-20 μm) on stainless steel 316L implant materials were investigated. The coatings were characterized by scanning electron and confocal microscopes, microindentation and scratch tests, whereas their protective properties were evaluated in terms of quenching metal ion release from stainless steel to simulated body fluid (Hanks solution). The obtained results revealed that for parylene C coatings, the critical load for initial cracks is 3-5 times higher and the total metal ions release is reduced 3 times more efficiently compared to parylene N. It was thus concluded that parylene C exhibits superior mechanical and protective properties for application as a micrometer coating material for stainless steel implants.     

Evolution of microstructure and mechanical properties for 9Cr18 stainless steel during thixoforming

Hot compression tests were carried out in the semi-solid state of 9Cr18 stainless steel on Gleeble-1500 thermal simulation testing machine to investigate the effects of thixoforming parameters on its microstructure and mechanical properties. In this paper, microstructure was observed by scanning electron microscopy (SEM) and analyzed using energy dispersive spectrometer (EDS), and true stress–stain curves of the specimens with different initial microstructures after thixoforming were obtained to study the deformation mechanism. The results showed that thixoforming parameters such as reheating temperature and the strain rate had a significant influence on microstructure and mechanical properties evolution of 9Cr18 semi-solid billet. With increasing reheating temperature or decreasing strain rate, average size of carbides decreased from 2 μm to 0.5 μm, and the phenomenon of liquid extrusion during thixoforming became more obvious. During thixoforming, carbon atoms diffused to molten metal from austenite in the centre of specimens. When thixoforming temperature reached 1300 °C, martensitic transformation occurred after rapid cooling. Flow stress of semi-solid billet was lower than traditional ingot casting and hot rolled state steel, when reheated to the semi-solid range, due to their different original microstructure.     

Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes

Irregular grains, high interfacial stresses and anisotropic properties widely exist in 3D-printed metallic materials, and this paper investigated the effects of heat treatment on the microstructural, mechanical and corrosion properties of 316 L stainless steel fabricated by selective laser melting. Sub-grains and low-angle boundaries exist in the as-received selective laser melted (SLMed) 316 L stainless steel. After heat treatment at 1050 °C, the sub-grains and low-angle boundaries changed slightly, and the stress state and strength decreased to some extent due to the decrease of dislocation density. After heat treatment at 1200 °C, the grains became uniform, and the dislocation cells vanished, which led to a sharp decline in the hardness and strength. However, the ductility was improved after recrystallization heat treatment. The passive film thickness and corrosion potential of the SLMed 316 L stainless steel decreased after heat treatment, and the pitting potential also decreased due to the accelerated transition from metastable to steady-state pitting; this accelerated transition was caused by the presence of weak passive films at the enlarged pores after heat treatment, especially for an adequate solid solution treatment.     

Effect of interlayer addition on microstructure and mechanical properties of NiTi/stainless steel joint by electron beam welding

NiTi/Stainless Steel(SS) sheets have been welded via a vacuum electron beam welding process, with three methods(offsetting electron beam to SS side without interlayer, adding Ni interlayer and adding Fe Ni interlayer), to promote mechanical properties of the Ni Ti/SS joints. The joints with different interlayers are all fractured in the weld zone near the Ni Ti side, which is attributed to the enrichment of intermetallic compounds including Fe2 Ti and Ni3 Ti. The fracture mechanisms of different joints are strongly dependent on the types of interlayers, and the joints without interlayer, adding Ni interlayer and adding Fe Ni interlayer exhibit cleavage fracture, intergranular fracture and mixed fracture composed of cleavage and tearing ridge, respectively. Compared with the brittle laves phase Fe2 Ti, Ni3 Ti phase can exhibit certain plasticity, block the crack propagation and change the direction of crack propagation. The composite structure of Ni3 Ti and Fe2 Ti will be formed when the Fe Ni alloy is taken as the interlayer, which provides the joint excellent mechanical properties, with rupture strength of 343 MPa.     

Effect of aging treatment on the microstructures and mechanical properties evolution of 25Cr-20Ni austenitic stainless steel weldments with different Nb contents

The microstructure evolutions and the mechanical properties of the 25Cr-20Ni austenitic stainless steel weld metals with different Nb contents were investigated during the long term aging treatment at 700~?C.M_(23)C_6,Nb(C,N),α-Cr phase and Nb-nitride phase(Z phase)were observed in the microstructures of the aged weld metals.The results showed that theα-Cr phase precipitated in the interdendritic regions of the weld metals after being exposed to~ 700?C for 500 h and the element Nb accelerated the precipitation of theα-Cr phase significantly.The density of theα-Cr phase decreased with the increase of the distance away from the primary Nb(C,N).Additionally,theα-Cr phase showed a crystallographic relationship with the austenitic matrix,■.It was observed that the Z phase precipitated in the periphery of the Nb(C,N)and may replace the Nb(C,N)after long term exposure to high temperature.The transformation of the Nb(C,N)into Z phase suggested that the Z phase had a higher stability than the Nb(C,N)par~ticles at 700?C for long term aging.The tensile strength of the Nb-bearing weld metal showed a continuous decrease at the initial stage of the aging treatment and then went up slightly with the prolonged aging time.However,the elongations and the impact energies of the weld metals decreased monotonously with the increase of the aging time.     

Notch effect on torsional fatigue of austenitic stainless steel: Comparison with low carbon steel

Notch effect in austenitic stainless steel under cyclic torsion is quite different depending on the superposition of static tension. In pure torsion, the rubbing of the serrated factory-roof type crack faces delays the crack growth along the notch root. Thus, the lifetime in notched specimen becomes longer than in smooth specimen. However, in cyclic torsion with static tension, the flat crack path and mean tensile stress reduce the influence of the crack face contact. Accordingly, shorter lifetime resulted from higher strain concentration at the notch root. Crack growth in low carbon steel under cyclic torsion is highly affected by the ferrite/pearlite banded microstructure besides the addition of static tension. Because of a small amount of the crack face contact, the reduction of lifetime in notched specimen is revealed irrespective of superposition of static tension.     

Microstructure and properties of low manganese and niobium containing HIC pipeline steel

The paper describes the concept of using low manganese content in pipeline steels for hydrogen-induced cracking (HIC) applications. The microstructure of thermomechanically processed pipeline steel primarily consisted of polygonal ferrite and low fraction of pearlite. The cleanliness of the steel was evident as was the absence of centerline segregation. The microstructure contained high dislocation density, sub-boundaries and dislocation substructures. Fine-scale precipitation of niobium carbides occurred on parallel array of dislocations and on random dislocations that followed [0 0 1]_NbC//[0 0 1]_α-Fe relationship with the ferrite matrix.     

X-ray diffraction Rietveld analysis of cold worked austenitic stainless steel

In the present study, the dislocation density of cold worked austenitic stainless steel samples in the range 2-40% was calculated on the basis of Williamson-Smallman approach using modified Rietveld method. Dislocation density has been found to increase significantly with increasing percentage of cold work up to 20%. The dislocation density is found to be 1.8 × 10¹¹/m² for the annealed sample and are 3.6 × 10¹⁵/m² and 5.4 × 10¹⁵/m² for 20% and 40% cold worked sample, respectively. The effect of cold work on dislocation density, hardness and Fourier electron density of the cold worked samples is discussed in comparison with the annealed sample.     

ZrO_2对不锈钢焊条工艺性能的影响

在国产不锈钢焊条配方基础上添加新成分ＺｒＯ＿２，通过测定焊条表面温度、熔滴尺寸以及用高速摄影法观察熔滴过渡形态，探讨了ＺｒＯ＿２对焊条工艺性能的影响。试验证明，焊条药皮中加入约４％的Ｚｒｎ＿２将使熔滴尺寸细化，表面温度下降；焊条综合工艺性能明显改善。     

Effect of high temperature post-oxidizing on tribological and corrosion behavior of plasma nitrided AISI 316 austenitic stainless steel

In this research, the microstructure, tribological and corrosion properties of plasma nitrided-oxidized AISI 316 austenitic stainless steel at high oxidation temperature were studied and compared with conventional plasma nitride. The structural, tribological and corrosion properties were analyzed using XRD, SEM, microhardness testing, pin-on-disk tribotesting and electrochemical polarization. Plasma nitriding was conducted for 5 h at 450 °C with gas mixture of N₂/H₂ = 1/3 to produce the S-phase. The nitrided samples were post-oxidized at 500 °C with gas mixture of O₂/H₂ = 1/5 for 15, 30 and 60 min. X-ray diffraction confirmed the development of CrN, ? and γ′ nitride phases and magnetite (Fe₃O₄) oxide phase under plasma nitriding-oxidizing process. In addition, it was found that oxidation treatment after plasma nitriding provides an important improvement in the friction coefficient and the corrosion resistance. The optimized wear and corrosion resistance of post-oxidized samples were obtained after 15 min of oxidation.     

Constitutive modeling of nitrogen-alloyed austenitic stainless steel at low and high strain rates and temperatures

In this paper, microstructures-based constitutive relations are introduced to simulate the thermo-mechanical response of two nitrogen-alloyed austenitic stainless steels; Nitronic-50 and Uranus-B66, under static and dynamic loadings. The simulation of the flow stress is developed based on a combined approach of two different principal mechanisms; the cutting of dislocation forests and the overcoming of Peierls–Nabarro barriers. The experimental observations for Nitronic-50 and Uranus-B66 conducted by Guo and Nemat-Nasser (2006) and Fréchard et al. (2008), respectively, over a wide range of temperatures and strain rates are also utilized in understanding the underlying deformation mechanisms. Results for the two stainless steels reveal that both the initial yielding and strain hardening are strongly dependent on the coupling effect of temperatures and strain rates. The methodology of obtaining the material parameters and their physical interpretation are presented thoroughly. The present model predicts results that compare very well with the experimental data for both stainless steels at initial temperature range of 77–1000 K and strain rates between 0.001 and 8000 s⁻¹. The effect of the physical quantities at the microstructures on the overall flow stress is also investigated. The evolution of dislocation density along with the initial dislocation density contribution plays a crucial role in determining the thermal stresses. It was observed that the thermal yield stress component is more affected by the presence of initial dislocations and decreases with the increase of the originated (initial) dislocation density.     

Effect of water quench process on mechanical properties of cold rolled dual phase steel microalloyed with niobium

Effect of water quench process on tensile properties of microalloyed dual phase (DP) steel was investigated. The results showed that the tensile strength and yield strength decrease while total elongation increases with decreasing quenching temperature. Different quenching temperatures lead to not only different amounts of martensite, but also different volume fractions of new ferrite. Due to exemption of precipitation strengthening, new ferrite will contribute to not only the increase of ductility, but also the improvement of microalloyed DP steel strength.     

Tensile ductility and deformation mechanisms of a nanotwinned 316L austenitic stainless steel

A nanotwinned 316 L austenitic stainless steel was prepared by means of surface mechanical grinding treatment.After recovery annealing,the density of dislocations decreases obviously while the average twin/matrix lamella thickness still keeps in the nanometer scale.The annealed nanotwinned sample exhibits a high tensile yield strength of 771 MPa and a considerate uniform elongation of 8%.TEM observations showed that accommodating more dislocations and secondary twinning inside the nanotwins contribute to the enhanced ductility and work hardening rate of the annealed nanotwinned sample.     

Mechanical properties of friction stir butt welds of high nitrogen-containing austenitic stainless steel

In this study, the friction stir butt welding of 2-mm-thick high nitrogen-containing stainless steel (HNS; Ni-free austenitic stainless steel containing 1 mass% nitrogen) plates was performed using a load-controlled friction stir welding (FSW) machine with a Si₃N₄-based tool at various welding speeds, i.e., 50 mm/min, 100 mm/min, 200 mm/min and 300 mm/min, and a constant tool rotating speed of 400 rpm. To determine the optimum welding conditions to create reliable HNS FSW joints, the effect of the heat input on the mechanical properties of the HNS FSW joints was studied. The mechanical properties were evaluated by the Vickers hardness test and the tensile strength test. Full-penetrated and defect-free butt welded joints were successfully produced, under all the applied welding conditions. The stir zones consisted of very fine grained structures and showed an increase in the Vickers hardness. These joints also showed a higher tensile strength and yield strength than the base metal. In particular, the FSW welds obtained at a welding speed of 100 mm/min, which showed the best mechanical properties, had a relatively higher Vickers hardness, which indicates a good relationship between the welding parameter (heat input) and the hardness profile due to the microstructure refinements. It was estimated that these welding conditions were optimal, and under these conditions both grain growth and α-phase formation were prevented.     

Novel plasma nitriding-oxidizing duplex treatment of AISI 316 austenitic stainless steel

In this work, plasma nitriding and plasma nitriding-oxidizing treatment have been performed on AISI 316 austenitic stainless steel. In order to evaluate its response to this treatment, their microstructures and wear resistance have been compared with conventional plasma nitrided. The treatment of plasma nitriding was performed at temperature of 450 °C for 5 h with gas mixture of N₂/H₂:1/3 whereas plasma nitriding-oxidizing was performed with the same parameters of plasma nitriding and temperature of 450 °C with gas mixture of O₂/H₂:1/5 for 15, 30 and 60 min. The structural, mechanical and tribological properties were analyzed using XRD, SEM, microhardness testing and pin-on-disk tribotesting. The results showed that oxidation treatment reduces wear resistance of plasma nitrided sample under high loads. Furthermore the tribological evaluation indicates that by increasing the oxidation time further reduction of wear resistance can be occurred. In addition, it was found that oxidation treatment after plasma nitriding provides an important improvement in the friction coefficient against a AISI 52100 steel pin and reduces surface roughness.