Viscoelastic and electrical properties of RGO reinforced phenol formaldehyde nanocomposites

Graphene oxide was reduced (RGO) by naturally abundant potato starch and incorporated in phenol formaldehyde resin (PF). The PF/RGO nanocomposites were successfully fabricated by the combination of solution processing and compression molding. Here, nanocomposites composed of 0.05 wt% to 1 wt% RGO were prepared. The incorporation of RGO into the PF matrix was significantly affecting the dynamic mechanical characteristics of the nanocomposites such as storage and loss modulus and tan δ. The degree of entanglement (N), effectiveness of filler (β_f ), reinforcement efficiency factor (r), cross-link density (v_c ), and adhesion factor (A) were evaluated from the modulus values. Besides, the phase behavior of the nanocomposites was analyzed with help of Cole–Cole plot. The electrical properties of the nanocomposites have been studied concerning change in filler loading and frequency. The dielectric constant (ε′), dielectric loss (ε″) and conductivity were increased with increase in wt% of filler for the entire range of frequencies (20 Hz to 30 MHz) and the results showed that the electrical conductivity of the nanocomposites can be explained by percolation theory. The Maxwell-Garnet model was employed to calculate the theoretical dielectric constant of PF/RGO nanocomposites.     

COOHMWCNTs‐induced BiFeO3‐poly(vinylidene fluoride) (PVDF) composites with enhanced dielectric and ferroelectric properties

In this work, flexible three phase composite films were prepared with surface functionalized multi‐walled carbon nanotubes (f‐MWCNTs) and bismuth ferrite (BiFeO₃;BFO) particles embedded into the poly(vinylidene fluoride) (PVDF) matrix via solution casting technique. The properties and the microstructure of prepared composites were investigated using an impedance analyzer and field emission scanning electron microscope. The micro‐structural study showed that the f‐MWCNTs and BFO particles were dispersed homogeneously within the PVDF matrix, nicely seated on the floor of the f‐MWCNTs separately. The dielectric measurement result shows that the resultant composites with excellent dielectric constant (≈96) and relatively lower dielectric loss (<0.23 at 100 Hz). Furthermore, the percolation theory is explored to explain the dielectric properties of the resultant composites. It says that the percolation threshold of f_MWCNTs = 0.9 wt % and the enhancement of the dielectric constant of the composite was also discussed. In addition, the remnant polarization of the un‐poled PVDF‐BFO‐f‐MWCNTs composites (2P_r ～1.34 µC/cm² for 1.1 wt % of f‐MWCNTs) is also improved. These three phase composites provide a new insight to fabricate flexible and enhanced dielectric properties as a promising application in modern electrical and electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46002.     

COOH?MWCNTs‐induced BiFeO3‐poly(vinylidene fluoride) (PVDF) composites with enhanced dielectric and ferroelectric properties

In this work, flexible three phase composite films were prepared with surface functionalized multi‐walled carbon nanotubes (f‐MWCNTs) and bismuth ferrite (BiFeO₃;BFO) particles embedded into the poly(vinylidene fluoride) (PVDF) matrix via solution casting technique. The properties and the microstructure of prepared composites were investigated using an impedance analyzer and field emission scanning electron microscope. The micro‐structural study showed that the f‐MWCNTs and BFO particles were dispersed homogeneously within the PVDF matrix, nicely seated on the floor of the f‐MWCNTs separately. The dielectric measurement result shows that the resultant composites with excellent dielectric constant (≈96) and relatively lower dielectric loss (<0.23 at 100 Hz). Furthermore, the percolation theory is explored to explain the dielectric properties of the resultant composites. It says that the percolation threshold of f_MWCNTs = 0.9 wt % and the enhancement of the dielectric constant of the composite was also discussed. In addition, the remnant polarization of the un‐poled PVDF‐BFO‐f‐MWCNTs composites (2P_r ～1.34 µC/cm² for 1.1 wt % of f‐MWCNTs) is also improved. These three phase composites provide a new insight to fabricate flexible and enhanced dielectric properties as a promising application in modern electrical and electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46002.     

TPU/PLA nanocomposites with improved mechanical and shape memory properties fabricated via phase morphology control and incorporation of multi-walled carbon nanotubes nanofillers

Shape memory polymer nanocomposites based on thermoplastic polyurethane (TPU)/polylactic acid (PLA) blends filled with pristine multi-walled carbon nanotubes (MWCNTs) and modified MWCNTs─COOH were fabricated by direct melt blending technique and investigated for its morphology, mechanical, thermal, electrical, and shape memory properties. Morphological characterizations by using transmission electron microscope (TEM) and field emission scanning electron microscope (FESEM) revealed better dispersion of MWCNTs─COOH in the polymer blend, which is attributed to the improved interfacial interactions between the polymer blends and MWCNTs-COOH. Loading of the MWCNTs-COOH in the TPU/PLA blends resulted in the significant improvements in the mechanical properties such as tensile strength and elastic modulus and these effects are more pronounced on increasing the MWCNTs─COOH loading amount, when compared to the pristine MWCNTs filled system. Thermal analysis showed that the glass transition temperature of the blends increases slightly with increasing loading of both pristine and modified MWCNTs in the system. The resistance of nanocomposites decreased from 2 × 10¹² Ω to 3.2 × 10¹⁰ Ω after adding 3% MWCNTs─COOH. The shape memory performance tests showed that the enhancement of shape recovery by 252% could be achieved at 3% MWCNTs loading, when compared to that of TPU/PLA blends.     

Effects of graphene nanosheets on the dielectric,mechanical, thermal properties,and rheological behaviors of poly(arylene ether nitriles)

Poly(arylene ether nitriles) (PEN) containing various contents of graphene nanosheets (GNs) was prepared via solution‐casting method and investigated for their dielectric, mechanical, thermal, and rheological properties. For PEN/GNs nanocomposite with 5 wt % GNs, the dielectric constant was increased to 9.0 compared with that of neat PEN (3.1) and dielectric losses of all nanocomposites were in the range of 0.019–0.023 at 1 kHz. The tensile modulus and strength were increased about 6 and 14% with 0.5% GNs, respectively. The fracture surfaces of the all PEN/GNs nanocomposites revealed that GNs had good adhesion to PEN matrix. The thermal properties of the nanocomposites showed significant increase with increasing GN loading. For 5 wt % GNs‐reinforced PEN nanocomposite, the temperatures corresponding to a weight loss of 5 wt % (T_d5%) and 30 wt % (T_d30%) increased by about 20 and 13°C, respectively. Rheological properties of the PEN nanocomposites showed a sudden change with the GN fraction and the percolation threshold was about 1 wt % of GNs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of alternating current impedance analysis and dielectric properties of carbon nanotube‐based polysulfone nanocomposites

Polysulfone (PSU)/multiwalled carbon nanotubes (MWCNTs) nanocomposites containing 0.5–3 wt% of MWCNTs were prepared by solution casting technique. To understand the dispersion behavior of MWCNTs inPSU matrix, high resolution transmission electron microscopy (HRTEM) and field emission scanning electron microscopy (FESEM) were used. Electrical properties of nanocomposites were investigated by analyzing alternating current (AC) impedance spectra. The real part of complex impedance was decreased with increasing carbon nanotubes loading in the PSU matrix, which may be due to increase in conductive networks in the nanocomposite. The complex impedance Nyquist plots for PSU/MWCNTs nanocomposites were characterized by the appearance of a single semicircular arc, whose radii of curvature decreases with increasing MWCNTs loading. The polarization mechanism and the AC conduction mechanism were studied by designing equivalent circuit from impedance data. The dielectric response of PSU/MWCNTs nanocomposite was investigated over a wide range of frequency from 10 Hz to 10⁻⁶ Hz. Dielectric constant of PSU/MWCNTs nanocomposite was enhanced significantly from 2 to 6 × 10¹⁰ at 10 Hz when the addition of MWCNTs was increased from 0 to 3 wt%. The enhancement of dielectric property might be due to the interfacial polarization between carbon nanotubes and polysulfone. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Nanocomposite films of poly(vinylidene fluoride) filled with polyvinylpyrrolidone‐coated multiwalled carbon nanotubes: Enhancement of β‐polymorph formation and tensile properties

To improve interactions between carbon nanotubes (CNTs) and poly(vinylidene fluoride) (PVDF) matrix, multiwalled CNTs (MWCNTs) were successfully coated with amphiphilic polyvinylpyrrolidone (PVP) using an ultrasonication treatment performed in aqueous solution. It was found that PVP chains could be attached noncovalently onto the nanotubes' surface, enabling a stable dispersion of MWCNTs in both water and N,N‐dimethylformamide. PVP‐coated MWCNTs/PVDF nanocomposite films were prepared by a solution casting method. The strong specific dipolar interaction between the PVP's carbonyl group (C?O) and the PVDF's fluorine group C?F₂ results in high compatibility between PVP and PVDF, helping PVP‐coated MWCNTs to be homogenously dispersed within PVDF. Fourier transform infrared and X‐ray diffraction characterization revealed that the as‐prepared nanocomposite PVDF films exhibit a purely β‐polymorph even at a very low content of PVP‐wrapped MWCNTs (0.1 wt%) while this phase is totally absent in the corresponding unmodified MWCNTs/PVDF nanocomposites. A possible mechanism of β‐phase formation in PVP‐coated MWCNTs/PVDF nanocomposites has been discussed. Furthermore, the tensile properties of PVDF nanocomposites as function of the content in PVP‐coated MWCNTs were also studied. Results shows that the addition of 2.0 wt% of PVP‐coated MWCNTs lead to a 168% increase in Young's modulus and a 120% in tensile strength. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Effects of crosslinking degree and carbon nanotubes as filler on composites based on glycidyl azide polymer and propargyl‐terminated polyether for potential solid propellant application

Triazole crosslinked polymers were prepared by reacting glycidyl azide polymer (GAP) with the propargyl ‐ terminated poly(tetramethylene oxide) (PTMP) at different molar ratios of azide versus alkyne. Based on the optimum mechanical properties of the GAP/PTMP ‐ 2.5, a series of GAP/PTMP nanocomposites reinforced by either multi ‐ walled carbon nanotubes (MWCNTs) or carboxy ‐ functionalized multiwalled carbon nanotubes (MWCNTs ‐ COOH) were prepared with different mass ratios. The glass transition temperatures (T_{g, PTMP}) assigned to PTMP of the GAP/PTMP composites almost kept at a constant range when the molar ratio of azide versus alkyne was from 1.0 to 2.5. When the loading MWCNTs was 1.0 wt %, the tensile strength and elongation at break achieved a maximum of 1.77 MPa and 36.3%, respectively. The nanocomposites with nearly similar T_{g, PTMP} indicated no phase separation in the crosslinked polymers. The results revealed that the improved properties of GAP ‐ based materials could be achieved by changing the molar ratio of azide versus alkyne and the nanofillers content. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45359.     

Enhanced dielectric constant and suppressed electrical conductivity in polymer nanocomposite films via loading MXene/TiO2/MoS2 nanosheets

Conductor/polymer nanocomposites can achieve high dielectric constant with low filler loading, but conductive fillers come into contact with each other easily, resulting in the formation of conductive paths. In this work, MXene/TiO₂/MoS₂ nanosheets were prepared by one-step hydrothermal method, and MXene/TiO₂/MoS₂/poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) nanocomposite films were prepared by solution casting method. At 1 kHz, with an optimized MXene/TiO₂/MoS₂ nanosheets loading of 8.0 wt%, MXene/TiO₂/MoS₂/P(VDF-HFP) nanocomposite films achieve a high dielectric constant of 944 and maintain a low dielectric loss of 0.19. TiO₂ and MoS₂ semiconductive layers on the surface of MXene nanosheets can prevent the formation of conductive paths, and therefore, nanocomposite films possess suppressed electrical conductivity. Moreover, MXene/TiO₂/MoS₂ nanosheets can build more microcapacitor structures in nanocomposite films with higher filler loading, which further improves the dielectric constant of nanocomposite films. Finite element simulation shows that TiO₂ and MoS₂ semiconductive layers can lower the electric field intensity and polarization intensity at the interface between conductive fillers and polymer matrix. Herein, MXene/TiO₂/MoS₂/P(VDF-HFP) nanocomposite films possess not only excellent dielectric properties, but also excellent mechanical properties, which can be used as flexible dielectric materials in electronic packaging technology.     

Effect of nitrile functionalized graphene on the properties of poly(arylene ether nitrile) nanocomposites

In this study, novel nitrile functionalized graphene (GN‐nitrile)/poly(arylene ether nitrile) (PEN) nanocomposites were prepared by an easy solution‐casting method and investigated for the effect of surface modification on the dielectric, mechanical and thermal properties. Graphene (GN) was first functionalized by introduction of nitrile groups onto the GN plane, which was confirmed by scanning electron microscopy, differential scanning calorimetry, Fourier transform infrared spectroscopy, thermogravimetric analysis and dispersibility research. Compared with pure GN, the grafted nitrile groups on the GN‐nitrile can interact with nitrile groups in PEN and lead to flat but better dispersion and stronger adhesion in/to the PEN matrix. Consequently, GN‐nitrile had a more significant enhancement effect on the properties of PEN. The dielectric constant of the PEN/GN‐nitrile nanocomposite with 5 wt% GN‐nitrile reaches 11.5 at 100 Hz, which is much larger than that of the pure PEN matrix (3.1). Meanwhile, dielectric loss is quite small and stable and the dielectric properties showed little frequency dependence. For 5 wt% GN‐nitrile reinforced PEN composites, increases of 17.6% in tensile strength, 26.4% in tensile modulus and 21 °C in T_d5% were obtained. All PEN/GN‐nitrile nanocomposite films can stand high temperature, up to 480 °C. Hence, novel dielectric PEN/GN‐nitrile nanocomposite films with excellent mechanical and thermal properties can be used as dielectric materials under some critical circumstances such as high wear and temperature. Copyright © 2012 Society of Chemical Industry     

PVDF/BaTiO3/carbon nanotubes ternary nanocomposites prepared by ball milling: Piezo and dielectric responses

Nanocomposites based on poly(vinylidene fluoride) (PVDF) filled with barium titanate, BaTiO₃, (BT) particles, and multiwalled carbon nanotubes (MWCNTs) were prepared by high-energy ball milling (HEBM) and subsequent hot pressing. This method of materials preparation allowed obtaining uniform dispersions of the nanofillers. The influence of the particles on the polymer structure and morphology was studied. To understand the origin of changes in the PVDF properties, thermal and electrical behaviors of the PVDF/BT/MWCNT nanocomposites were studied as a function of composition. The addition of BT, MWCNT, or its mixture had not any influence on the PVDF polymorphism. However, calorimetric results pointed out that the presence of the nanofillers exerted nucleation mainly ascribed to the surface to volume ratio of the nanoparticles. The capacitance of the composites increased as the nanofiller content increased, being the effect mainly dependent on the surface to volume ratio of the nanoparticles. The dielectric behavior of the materials as a function of frequency was modeled by a Debye equivalent circuit only below the percolation threshold respect to the amount of MWCNT. The piezoelectric behavior of the ternary nanocomposites was highly affected by the incorporation of the nanofillers only when high dielectric losses occurred above the percolation threshold. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47788.     

Synthesis and characterization of (Fe3O4/MWCNTs)/ epoxy nanocomposites

A sonochemical technique is used for in situ coating of iron oxide (Fe₃O₄) nanoparticles on outer surface of MWCNTs. These Fe₃O₄/MWCNTs were characterized using a high‐resolution transmission electron microscope (HRTEM), X‐ray diffraction, and thermogravimetric analysis. The as‐prepared Fe₃O₄/MWCNTs composite nanoparticles were further used as reinforcing fillers in epoxy‐based resin (Epon‐828). The nanocomposites of epoxy were prepared by infusion of (0.5 and 1.0 wt %) pristine MWCNTs and Fe₃O₄/MWCNTs composite nanoparticles. For comparison purposes, the neat epoxy resin was also prepared in the same procedure as the nanocomposites, only without nanoparticles. The thermal, mechanical, and morphological tests were carried out for neat and nanocomposites. The compression test results show that the highest improvements in compressive modulus (38%) and strength (8%) were observed for 0.5 wt % loading of Fe₃O₄/MWCNTs. HRTEM results show the uniform dispersion of Fe₃O₄/MWCNTs nanoparticles in epoxy when compared with the dispersion of MWCNTs. These Fe₃O₄/MWCNTs nanoparticles‐infused epoxy nanocomposite shows an increase in glass transition (T_g) temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Chemical Grafting of Crosslinked Polypyrrole and Poly(vinyl Chloride) onto Modified Graphite: Fabrication,Characterization, and Material Properties

ABSTRACT

Conjugated polymer/graphite nanocomposites have been known as high performance materials owing to improve the physicochemical properties relative to conventional once. Multilayered polymer nanocomposites based on polypyrrole (PPy), polyvinylchloride (PVC) as matrices and p-phenylene diamine (PDA) as linker were prepared via chemical in situ polymerization process and subsequently investigated the physical characteristics of fabricated nanocomposites at various loadings. The structural characterization and morphology of prepared nanocomposites were inspected by Fourier transform infrared spectroscopy (FTIR), X-ray photon spectroscopy (XPS), energy dispersive X-ray spectroscope (EDX), field emission scanning electron microscope (FESEM), respectively. The composite III showed higher thermal stability at 10 wt% loading of PPy. According to differential scanning calorimetry (DSC), the glass transition temperature (T_g), melting temperature T_m, and crystallization temperature (T_c) of nanocomposites increases with PPy loading (2–10 wt%) owing to crosslinking and chain rigidity. Moreover, higher surface area was displayed by the multilayered PPy/PVC/PDA@FG nanocomposites. Remarkably, electrical conductivity of ultimate nanocomposites was also found to be a function of PPy loading.     

Polyvinylidenefluoride/Poly(styrene-butadiene-styrene)/Silver Nanoparticle-grafted-Acid Chloride Functional MWCNTs-Based Nanocomposites: Preparation and Properties

A new type of nanofiltration membranes was synthesized using solution blending polyvinylidine fluoride (PVDF) and poly(styrene-butadiene-styrene) with acid chloride-modified multi-walled carbon nanotubes (MWNTs-COCl) and acid chloride-modified nanotbes-grafted-silver nanoparticles (MWNTs-COCl-Ag). SEM of PVDF/SBS-MWCNTs-COCl-Ag nanocomposite membranes showed polymer-coated Ag particles grafted on the surface. Tensile testing depicted the enhanced mechanical stability of PVDF/SBS-MWCNTs-COCl-Ag membranes around 18.8–22.4 MPa relative to PVDF/SBS-MWCNTs-COCl (10.1–13.3 MPa). 0.1 wt.% MWCNTs-COCl-Ag also enhanced the water permeability of membrane. Moreover, acid chloride-modified MWCNTs and Ag nanoparticles enhanced thermal properties to T₀ of 358°C, T₁₀ of 476°C and T_max around 599°C.     

Tensile,stress-strain and creep rupture properties of poly (vinyl chloride)/poly(neopentyl glycol adipate)/poly(vinylidene fluoride) blends

Poly (vinyl chloride), PVC, and poly(vinylidene fluoride), PVDF, are incompatible polymers. Poly(neopentyl glycol adipate), PDPA, is miscible with both PVC and PVDF. With PDPA acting as a compatibilizer between PVC and PVDF. compatible PVC/PDPA/PVDF blends can be formed at PVDF content of about less than 50wt%. Above 50wt% PVDF the ternary blends exist in two phases exhibiting two glass transition temperatures, T_g, PVC is the main contributor to the mechanical strength while PDPA and PVDF contribute to the elastic properties of these blends. A compatible blend of 55/22.5/22.5 wt% PVC/PDPA/PVDF exhibiting one single T_g appears to show an interesting balance of the properties of the blend components.     

Synthesize procedures,mechanical and electrical properties of poly(vinylidene fluoride) nanocomposite thin films containing multiwalled carbon nanotubes

A procedure is proposed to prepare poly(vinylidene fluoride) (PVDF) multiwalled carbon nanotubes (MWCNTs) nanocomposite thin films with improved mechanical and dielectric properties compared to the pure PVDF films. The PVDF/MWCNT mixture with a composition range from 0.0 to 5.0% MWCNTs by weight was formed using solution blending and the ultrasonic dispersion method and then spin coated on a rotating glass substrate to produce films nearly 20 μ thick. Results indicate that the appropriate addition of MWCNTs (up to 3.0 wt%) to PVDF can significantly increase its elastic modulus while decrease its fracture toughness. The elastic modulus shows softening at a 5.0 wt% MWCNT loading. The DC and AC conductivity of the composite films were also examined with various MWCNTs concentrations. The dielectric constants were found more than doubled for 0.5 wt% MWCNTs composite compared to the values for the pure PVDF. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Crystallinity of biodegradable polymers reinforced with functionalized carbon nanotubes

Well-dispersed multiwall carbon nanotubes (MWCNTs) were prepared by grafting poly(L-lactide-co-ε-caprolactone) (PLACL) biodegradable copolymer onto the sidewall of hydroxylated MWCNTs using oligomeric L-lactide (LA) and ε-caprolactone (CL). After preparation of MWCNT/PLACL composites, the effect of functionalized MWCNTs on crystallinity of PLACL was investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarized light optical microscopy (POM). The surface functionalization effectively improved the dispersion and adhesion of MWCNTs which acted as reinforcing filler in the PLACL polymer matrix and hence improved the physical and thermomechanical properties of the nanocomposites. The glass transition temperature (T _g) and the crystallinity of nanocomposites decreased in comparison with those of neat PLACL when the concentration of functionalized MWCNTs in nanocomposites was 0.5 wt%. With further increment in concentration of functionalized MWCNTs, the T _g of composites increased until the T _g of neat PLACL, and also the crystallinity of composites increased. The functionalized MWCNTs have no significant effect on the melting point of nanocomposites. The MWCNTs acted as heterogeneous nucleation points and increased the lamella size and therefore the crystallinity of PLACL. Furthermore, the larger agglomerated clusters of both kinds of MWCNTs (i.e., MWCNT-grafted-PLACL and pristine MWCNTs) are more effective than small clusters as nucleation points for growing the spherulites.     

Effect of carbon nanotube on PA6/ECO composites: Morphology development,rheological, and thermal properties

Thermoplastic elastomer (TPE) nanocomposites based on polyamide‐6 (PA6)/poly(epichlorohydrin‐co‐ethylene oxide) (ECO)/multiwall carbon nanotube (MWCNTs) were prepared by melt compounding process. Different weight ratios of ECO (20, 40, and 60 wt %) and two kinds of functionalized and non‐functionalized MWCNTs were employed to fabricate the nanocomposites. The morphological, rheological, and mechanical properties of MWCNTs‐filled PA6/ECO blends were studied. The scanning electron microscopy of PA6/ECO blends showed that the elastomer particles, ECO, are well‐dispersed within the PA6 matrix. The significant improvement in the dispersibility of the carboxylated carbon nanotubes (COOH‐MWCNTs) compared to that of non‐functionalized MWCNTs (non‐MWCNTs) was confirmed by transmission electron microscopy images. The tensile modulus of samples improved with the addition of both types of MWCNTs. However, the effect of COOH‐MWCNTs was much more pronounced in improving mechanical properties of PA6/ECO TPE nanocomposites. Crystallization results demonstrated that the MWCNTs act as a nucleation agent of the crystallization process resulted in increased crystallization temperature (T_c) in nanocomposites. Rheological characterization in the linear viscoelastic region showed that complex viscosity and a non‐terminal storage modulus significantly increased with incorporation of both types of MWCNTs particularly at low frequency region. The increase of rheological properties was more pronounced in the presence of carboxylic (COOH) functional groups, in the other words by addition of COOH‐MWCNTs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45977.     

New piezoelectric damping composites of poly(vinylidene fluoride) blended with clay and multi‐walled carbon nanotubes

Damping materials are used to control mechanical vibrations, and piezoelectric damping composite is a very promising material due to its unique mechanism. In this study, a potential piezoelectric damping composite was developed by simply melt mixing poly(vinylidene fluoride) (PVDF) with small amounts of organic modified montmorillonite (OMMT) and multi‐walled carbon nanotubes (MWCNTs). The piezoelectric, mechanical and electrical properties were investigated using a dynamic mechanical analyser, direct current electrical resistivity measurements, X‐ray diffraction, Fourier transform infrared spectroscopy and the direct quasi‐static d₃₃ piezoelectric coefficient method. It was found that the damping property of PVDF can be greatly improved by adding both MWCNTs and OMMT, and the composite containing 1.9 wt% of MWCNTs and 3 wt% of OMMT showed the best damping property. A model and an approximate calculation were applied to explain the improved damping property. Moreover, similar mechanical properties of PVDF composites were observed in the tensile testing and dynamic mechanical analyser measurements. Copyright © 2012 Society of Chemical Industry     

Effects of multi‐walled carbon nanotubes and conductive carbon black on electrical,dielectric, and mechanical properties of epoxidized natural rubber composites

The influence of multi‐walled carbon nanotubes (MWCNTs) and conductive carbon black (CCB) on cure, electrical, dielectric, and mechanical properties of epoxidized natural rubber (ENR) composites was investigated. It was found that short MWCNTs (S‐MWCNTs) with low loading significantly affected the cure characteristics in a way similar to high loading of CCB. Moreover, the ENR/S‐MWCNTs composites exhibited high AC conductivity, dielectric constant, and dielectric loss tangent (tan δ ) compared to the ENR/CCB and ENR/L‐MWCNTs (long MWCNTs) composites. In addition, the S‐MWCNTs composites showed the lowest percolation threshold concentration, defined as the lowest loading to form conductive paths in the insulating ENR matrix. This might be attributed to the comparatively high interfacial polarization, with good dispersion and distribution, of the S‐MWCNTs in ENR matrix. These characteristics were confirmed by TEM imaging and by a high bound rubber content, corroborating strong filler–rubber interactions in the ENR/S‐MWCNTs composites. However, the L‐MWCNTs composites showed the lowest electrical and other related properties, despite the highest aspect ratio and specific surface area of this filler. This might be because of the flocculation of nanotubes by mutual entanglement, leading to a poor uneven distribution in the ENR matrix. POLYM. COMPOS., 38:1031–1042, 2017. © 2015 Society of Plastics Engineers