Synchronous and separate homo-crystallization of enantiomeric poly(l-lactic acid)/poly(d-lactic acid) blends

High-molecular-weight poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) are blended at different ratios and their crystallization behavior was investigated. Solely homo-crystallites mixtures of PLLA and PDLA were synchronously and separately formed during isothermal crystallization in the temperature (T_c) range of 90–130 °C, irrespective of blending ratio, whereas in addition to homo-crystallites, stereocomplex crystallites were formed in the equimolar blends at T_c above 150 and 160 °C. Interestingly, in isothermal crystallization at T_c = 130 °C, the spherulite morphology of blends became disordered, the periodical extinction (periodical twisting of lamellae) in spherulites disappeared, and the radial growth rate of spherulite (G) of the blends was reduced by the synchronous and separate crystallization of PLLA and PDLA and the coexistence of PLLA and PDLA homo-crystallites. However, the interplane distance (d), the crystallinity (X_c), the transition crystallization temperature (T_c) from α′-form to α-form, the alternately stacked structure of the crystalline and amorphous layers, and the nucleation mechanism were not altered by the synchronous and separate crystallization of PLLA and PDLA and the coexistence of PLLA and PDLA homo-crystallites. The unchanged d, X_c, transition T_c, long period of stacked lamellae, and nucleation mechanism strongly suggest that the chiral selection of PLLA or PDLA segments on the growth sites of PLLA or PDLA homo-crystallites to some extent was performed during solvent evaporation and this effect remained even after melting.     

Relationship between the crystallization behavior of poly(ethylene glycol) and stereocomplex crystallization of poly(L‐lactic acid)/poly(D‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a good biomedical polymer material with wide applications. The addition of poly(ethylene glycol) (PEG) as a plasticizer and the formation of stereocomplex crystals (SCs) have been proved to be effective methods for improving the crystallization of PLLA, which will promote its heat resistance. In this work, the crystallization behavior of PEG and PLLA/poly(d ‐lactic acid) (PDLA) in PLLA/PDLA/PEG and PEG‐b‐PLLA/PEG‐b‐PDLA blends has been investigated using differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both SCs and homocrystals (HCs) were observed in blends with asymmetric mass ratio of PLLA/PDLA, while exclusively SCs were observed in blends with approximately equal mass ratio of PLLA/PDLA. The crystallization of PEG was only observed for the symmetric blends of PLLA_39k/PDLA_35k/PEG_2k, PLLA_39k/PDLA_35k/PEG_5k, PLLA_69k/PDLA_96k/PEG_5k and PEG‐b‐PLLA_31k/PEG‐b‐PDLA_27k, where the mass ratio of PLLA/PDLA was approximately 1/1. The results demonstrated that the formation of exclusively SCs would facilitate the crystallization of PEG, while the existence of both HCs and SCs could restrict the crystallization of PEG. The crystallization of PEG is related to the crystallinity of PLLA and PDLA, which will be promoted by the formation of SCs. © 2017 Society of Chemical Industry     

Highly enhanced accelerating effect of melt‐recrystallized stereocomplex crystallites on poly(L‐lactic acid) crystallization: effects of molecular weight of poly(D‐lactic acid)

The effects of the molecular weight of poly(D ‐lactic acid) (PDLA), which forms stereocomplex (SC) crystallites with poly(L ‐lactic acid) (PLLA), and those of processing temperature T_p on the acceleration (or nucleation) of PLLA homocrystallization were investigated using PLLA films containing 10 wt% PDLA with number‐average molecular weight (M_n) values of 5.47 × 10⁵, 9.67 × 10⁴ and 3.67 × 10⁴ g mol^–1 (PDLA‐H, PDLA‐M and PDLA‐L, respectively). For the PLLA/PDLA‐H and PLLA/PDLA‐M films, the SC crystallites that were ‘non’‐melted and those that were ‘completely’ melted at T_p values just above their endset melting temperature and recrystallized during cooling were found to act as effective accelerating (or nucleation) agents for PLLA homocrystallization. In contrast, SC crystallites formed from PDLA‐L, having the lowest M_n, were effective accelerating agents without any restrictions on T_p. In this case, the accelerating effects can be attributed to the plasticizer effect of PDLA‐L with the lowest M_n. The accelerating effects of SC crystallites in the PLLA/PDLA‐H and PLLA/PDLA‐M films was dependent on crystalline thickness for T_p values below the melting peak temperature of SC crystallites, whereas for T_p values above the melting peak temperature the accelerating effects are suggested to be affected by the interaction between the SC crystalline regions and PLLA amorphous regions.     

Effect of the melting temperature on the crystallization behavior of a poly(l‐lactide)/poly(d‐lactide) equimolar mixture

The effect of the final melting temperature (T_f) on the crystallization of poly(l ‐lactide) (PLLA)/poly(d ‐lactide) (PDLA) was studied via a combination of differential scanning calorimetry, wide‐angle X‐ray scattering, polarized optical microscopy, and Fourier transform infrared (FTIR) spectroscopy. We observed that a residual stereocomplex (SC) crystal induced the formation of SC crystals during cooling from a T_f (230°C) just above the melting peak of the SC crystals. On cooling from a T_f (240°C) just above the endset temperature of SC crystal melting [T_m(S)(E)], the possible order structure and the strong interchain interaction promoted the preferential crystallization of SC crystals; this enhanced the formation of α crystals. During cooling from a T_f (≥250°C) far above T_m(S)(E), the crystallization peaks of α and SC crystals converged. The FTIR results indicated that the residual SC crystals, possible ordered structure, and interchain interactions in the melt might have been the key factors for the different crystallization of PLLA/PDLA. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43015.     

Effect of multi‐branched PDLA additives on the mechanical and thermomechanical properties of blends with PLLA

Stereocomplex formation between poly(l ‐lactic acid) (PLLA) and poly(d ‐lactic acid) (PDLA) in the melt state was investigated and altered via the addition of multi‐branched poly(d ‐lactide) (PDLA) additives. Two different multi‐branched PDLA additives, a 3‐arm and 4‐arm star‐shaped polymeric structure, were synthesized as potential heat resistance modifiers and incorporated into PLLA at 5, 10, and 20 (w/w) through melt blending. Mechanical and thermomechanical properties of these blends were compared with linear poly(l ‐lactide) (PLLA) as well as with blends formed by the addition of two linear PDLA analogs that had similar molecular weights to their branched counterparts. Blends with linear PDLA additives exhibited two distinct melting peaks at 170–180°C and 200–250°C which implied that two distinct crystalline domains were present, that of the homopolymer and that of the stereocomplex, the more stable crystalline structure formed by the co‐crystallization of both d ‐ and l ‐lactide enantiomers. In contrast, blends of PLLA with multi‐branched PDLA formed a single broad melting peak indicative of mainly formation of the stereocomplex, behavior which was confirmed by X‐ray diffraction (XRD) analysis. The heat deflection temperature determined by thermal mechanical analysis was improved for all blends compared to neat PLLA, with increases of up to180°C for 20% addition of the 3‐arm PLLA additive. Rheological properties of the blends, as characterized by complex viscosity (η*), remained stable over a wide temperature range. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42858.     

Temperature dependence of crystalline transition of highly-oriented poly(l-lactide)/poly(d-lactide) blend: In-situ synchrotron X-ray scattering study

Formation of stereocomplex crystals (sc-crystals) of poly(l-lactide)/poly(d-lactide) (PLLA/PDLA) blend has been recognized as a unique opportunity to dramatically improve the heat-resistant of poly(lactic acid) (PLA). In this study, we investigated the dynamic formation and transition of sc-crystals in PLLA/PDLA drawn film with a combination of in-situ synchrotron wide-angle X-ray scattering (WAXS), small-angle X-ray scattering (SAXS) and differential scanning calorimetry (DSC). The correlation between sc-crystals content and the competing formation of α crystals (stable phase of PLA) in homopolymers during continuous heating and cooling processes was also studied. It was found that at room temperature, the original PLLA/PDLA drawn film consisted of only α crystals, however, with temperature increasing, two populations of sc-crystals were formed at different temperatures from the oriented amorphous region and the molten α crystals in the highly-oriented sample, respectively. Furthermore, new types of sc-crystals and α crystals with the orientation perpendicular to the original sc-crystals were formed during subsequent cooling process. On the basis of the X-ray scattering and DSC data, a schematic model for crystallization and oriented variation concerning sc-crystals and α crystals was proposed.     

Stereocomplexation and morphology of enantiomeric poly(lactic acid)s with moderate‐molecular‐weight

The thermal behavior and spherulitic morphologies of poly(L ‐lactic acid) (PLLA)/poly(D ‐lactic acid) (PDLA) 1/1 blend with weight‐molecular‐weight of 10⁵ order, together with those of pure PLLA and PDLA, were investigated using differential scanning calorimetry and polarized optical microscopy. It was found that in the blend, stereocomplex crystallites could be formed exclusively or coexisted with homocrystallites depending on thermal history. Banded to nonbanded spherulitic morphological transition occurred for melt‐crystallized PLLA and PDLA, while the blend presented exclusively nonbanded spherulitic morphologies in the temperature range investigated. The spherulite growth of the blend occurred within a wider temperature range (≤180°C) compared with that of homopolymers (≤150°C), while the spherulite growth rates were comparable for both the blend and homopolymers. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Isothermal crystallization and spherulite growth behavior of stereo multiblock poly(lactic acid)s: Effects of block length

Stereo multiblock poly(lactic acid)s (PLA)s and stereo diblock poly(lactic acid) (DB) with a wide variety of block length of 15.4–61.9 lactyl units are synthesized, and the effects of block length sequence on crystallization and spherulite growth behavior are investigated at different crystallization temperatures, in comparison with neat poly(L ‐lactide) (PLLA), poly(D ‐lactide) (PDLA), and PLLA/PDLA blend. Only stereocomplex crystallites as crystalline species are formed in the stereo multiblock PLAs and DB, irrespective of block length and crystallization temperature. The maximum crystallinities (33–61%), maximum radial growth rate of spherulites (0.7–56.7 μm min^?1), and equilibrium melting temperatures (182.0–216.5°C) increased with increasing block length but are less than those of PLLA/PDLA blend (67 %, 122.5 μm min^?1, and 246.0°C). The spherulite growth rates and overall crystallization rates of the stereo multiblock PLAs and DB increased with increasing block length and are lower than that of PLLA/PDLA blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Non‐Isothermal Crystallization Behavior of Poly(L‐lactic acid) in the Presence of Various Additives

Summary: The effects of various additives: poly(D ‐lactic acid) (PDLA), talc, fullerene C₆₀, montmorillonite, and various polysaccharides, on the non‐isothermal crystallization behavior of poly(L ‐lactic acid) (PLLA), during both the heating of melt‐quenched films from room temperature, and the cooling of as‐cast films from the melt, was investigated. When the melt‐quenched PLLA films were heated from room temperature, the overall PLLA crystallization was accelerated upon addition of PDLA or the stereocomplex crystallites formed between PDLA and PLLA, the mixtures containing PDLA, and the mixture of talc and montmorillonite. No significant effects on the overall PLLA crystallization were observed for talc, C₆₀, montmorillonite, and the mixtures containing C₆₀. Such rapid completion of the overall PLLA crystallization upon addition of the aforementioned additives can be ascribed to the increased density (number per unit volume or area) of PLLA spherulites. When the as‐cast PLLA films were cooled from the melt, the overall PLLA crystallization completed rapidly, upon addition of PDLA, talc, C₆₀, montmorillonite, and their mixtures. Such rapid overall PLLA crystallization is attributable to the increased density of the PLLA spherulites and the higher nucleation temperature for PLLA crystallization. In contrast, the addition of various polysaccharides has no significant effect, or only a very small effect, on the overall PLLA crystallization during heating from room temperature or during cooling from the melt. This finding means that the polysaccharides can be utilized as low‐cost fillers for PLLA‐based materials, without disturbing the crystallization of the PLLA. The effect of additives in accelerating the overall PLLA crystallization during cooling from the melt, decreased in the following order: PDLA > talc > C₆₀ > montmorillonite > polysaccharides.

Polarization optical photomicrographs of pure PLLA, and the PLLA‐F film, with the fullerene additive, during cooling from the melt (Process IIB). Both of the photomicrographs were taken at 120 °C.     

Effect of nucleating agents on the crystallization behavior and heat resistance of poly(l‐lactide)

Poly (l ‐lactide) (PLLA) blends with various nucleators were prepared by melt processing. The effect of different nucleators on the crystallization behavior and heat resistance as well as thermomechanical properties of PLLA was studied systematically by differential scanning calorimetry, X‐ray diffraction, heat deflection temperature tester, and dynamic mechanical analysis. It was found that poly(d ‐lactide), talcum powder (Talc), a multiamide compound (TMC‐328, abbreviated as TMC) can significantly improve the crystallization rate and crystallinity of PLLA, thus improving thermal–resistant property. The heat deflection temperature of nucleated PLLA can be as high as 150°C. The storage modulus of nucleated PLLA is higher than that of PLLA at the temperature above T_g of PLLA. Compared with other nucleating agents, TMC was much more efficient at enhancing the crystallization of PLLA and the PLLA containing TMC showed the best heat resistance. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42999.     

Unique Homo-Crystallization and Melting Behavior of Poly(L-lactic acid): Influence of Stereocomplex with Varied Structure

Homo-crystallization and melting behavior of poly(L-lactic acid) (PLLA) with poly(D-lactic acid) (PDLA) (≤10 wt.%) was studied. The different thermal history had been applied to exert structural variation on stereocomplex (SC). The PLLA/PDLA blend showed different crystallization and melting behavior when cooled from 250°C or 200°C. Double melting peaks were observed after the blend was cooled from 250°C. SC annealing at different temperatures exhibited significant effect for melt-crystallization of PLLA. Influence of initial melting condition before cooling was also investigated. The cold crystallization of amorphous blend initially was studied and some novel results had been observed.     

Enhanced crystallization of poly(lactide) stereocomplex by xylan propionate

The effect of xylan propionate (XylPr) as a novel biomass‐derived nucleating agent on the poly(lactide) sterecomplex was investigated. Addition of XylPr to an enantiomeric blend of poly(l ‐lactide) (PLLA) and poly(d ‐lactide) (PDLA) was performed in either the solution state or molten state. The solution blend of PLLA/PDLA with XylPr was prepared by mixing equal volumes of 1 wt% XylPr/PLLA and 1 wt% XylPr/PDLA solutions in chloroform and precipitating in methanol. The solution blend with XylPr showed shorter half‐time crystallization than the solution blend without XylPr in isothermal crystallization between 80 and 140 °C, although homocrystallization occurred. Enhanced stereocomplex crystallization in the solution blend with XylPr was observed at 180 °C, where no crystallization occurred in the solution blend without XylPr. Addition of XylPr to PLLA/PDLA blend in the molten state was performed at 240 °C. Thereafter, the melt blend of PLLA/PDLA with or without XylPr was either quenched in iced water or isothermally crystallized directly from the melt. Isothermal crystallization of the melt‐quenched blend with XylPr gave a similar result to the solution blend with XylPr. In contrast, the melt‐crystallized blend with XylPr formed only stereocomplex crystals after crystallization above 140 °C. Furthermore, the melt‐crystallized blend with XylPr showed a higher crystallinity index and melting temperature than the melt‐crystallized blend without XylPr. This shows that XylPr promotes stereocomplex crystallization only when the blend of PLLA/PDLA with XylPr is directly crystallized from the molten state just after blending. © 2016 Society of Chemical Industry     

The effect of poly(ethylene glycol) mixed with poly(l‐lactic acid) on the crystallization characteristics and properties of their blends

The non‐isothermal and isothermal crystallizations of extruded poly(l ‐lactic acid) (PLLA) blends with 10, 20 and 30 wt% poly(ethylene glycol) (PEG) were investigated with differential scanning calorimetry. The formation of α‐form crystals in the blend films was verified using X‐ray diffraction and an increase in crystallinity indexes using Fourier transformation infrared spectroscopy. Crystallization and melting temperatures and crystallinity of PLLA increased with decreasing cooling rate (CR) and showed higher values for the blends. Although PLLA crystallized during both cooling and heating, after incorporation of PEG and with CR = 2 °C min^?1 its crystallization was completed during cooling. Increasingly distinct with CR, a small peak appeared on the lower temperature flank of the PLLA melting curve in the blends. A three‐dimensional nucleation process with increasing contribution from nuclei growth at higher CR was verified from Avrami analysis, whereas Kissinger's method showed that the diluent effect of 10 and 20 wt% PEG in PLLA decreased the effective energy barrier. During isothermal crystallization, crystallization half‐time increased with temperature (T_ic) for the blends, decreased with PEG content and was lower than that of pure PLLA. In addition, the Avrami rate constants were significantly higher than those of pure PLLA, at the lower T_ic. Different crystal morphologies in the PLLA phase were formed, melting in a broader and slightly higher T_m range than pure PLLA. The crystallization activation energy of PLLA decreased by 56% after the addition of 10 wt% PEG, increasing though with PEG content. Finally, PEG/PLLA blends presented improved flexibility and hydrophilicity. © 2019 Society of Chemical Industry     

Enhanced crystallization rate and mechanical properties of poly(l‐lactic acid) by stereocomplexation with four‐armed poly(ϵ‐caprolactone)‐block‐poly(d‐lactic acid) diblock copolymer

Poly(l ‐lactic acid) (PLLA) was blended with a series of four‐armed poly(? ‐caprolactone)‐block ‐poly(d ‐lactic acid) (4a‐PCL‐b ‐PDLA) copolymers in order to improve its crystallization rate and mechanical properties. It is found that a higher content of 4a‐PCL‐b ‐PDLA copolymer or longer PDLA block in the copolymer lead to faster crystallization of the blend, which is attributed to the formation of stereocomplex crystallites between PLLA matrix and PDLA blocks of the 4a‐PCL‐b ‐PDLA copolymers. Meanwhile, the PDLA block can improve the miscibility between flexible PCL phase and PLLA phase, which is beneficial for improving mechanical properties. The tensile results indicate that the 10% 4a‐PCL_5k‐b ‐PDLA_5k/PLLA blend has the largest elongation at break of about 72% because of the synergistic effects of stereocomplexation between enantiomeric PLAs, multi‐arm structure and plasticization of PCL blocks. It is concluded that well‐controlled composition and content of 4a‐PCL‐b ‐PDLA copolymer in PLLA blends can significantly improve the crystallization rate and mechanical properties of the PLLA matrix. © 2017 Society of Chemical Industry     

Effect of poly(l‐lactide)/poly(d‐lactide) block length ratio on crystallization behavior of star‐shaped asymmetric poly(l(d)‐lactide) stereoblock copolymers

Effect of Poly(l ‐lactide)/Poly(d ‐lactide) (PLLA/PDLA) block length ratio on the crystallization behavior of star‐shaped poly(propylene oxide) block poly(d ‐lactide) block poly (l ‐lactide) (PPO–PDLA–PLLA) stereoblock copolymers with molecular weights (M_n) ranging from 6.2 × 10⁴ to 1.4 × 10⁵ g mol^?1 was investigated. Crystallization behaviors were studied utilizing differential scanning calorimetry (DSC), polarized optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). Only stereocomplex crystallites formed in isothermal crystallization at 140 to 156°C for all samples. On one hand, the overall crystallization rate decreased as PLLA/PDLA block length ratio increased. As PLLA/PDLA block length ratio increased from 7:7 to 28:7, the value of half time of crystallization (t_1/2) delayed form 2.85 to 5.31 min at 140°C. On the other hand, according to the Lauritzen–Hoffman theory, the fold‐surface energy (σ_e) was calculated. σ_e decreased from 77.7 to 73.3 erg/cm² with an increase in PLLA/PDLA block length ratio. Correspondingly increase in nucleation density was observed by the polarized optical microscope. Results indicated that the PLLA/PDLA block length ratio had a significant impact on the crystallization behavior of PPO–PDLA–PLLA copolymers. POLYM. ENG. SCI., 55:2534–2541, 2015. © 2015 Society of Plastics Engineers     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Highly Enhanced Nucleating Effect of Melt‐Recrystallized Stereocomplex Crystallites on Poly(L‐lactic acid) Crystallization

In the general processing temperature range of poly(L ‐lactic acid) (PLLA) articles (210–240 °C), PLLA/poly(D ‐lactic acid) (PDLA) stereocomplex (SC) crystallites melted just above the endset temperature of SC melting (228–238 °C) and recrystallized during cooling were found to act as the most effective nucleating agents for enhancing the crystallization of PLLA compared to partially melted SC crystallites (211–227 °C) or those melted far above the endset temperature of SC melting (240 and 250 °C) and recrystallized during cooling. The high nucleating effect of the SC crystallites melted in the temperature range of 228–238 °C was found to be caused by their smaller sizes or the larger number of SC crystallites per unit mass. The incorporation of such SC crystallites facilitates the processing of PLLA articles having high crystallinity and, therefore, high heat‐resistance in a shorter period to reduce the production cost.

     

Synergistic effects of N,N′‐bis (benzoyl) sebacic acid dihydrazide and talc on the physical and mechanical behaviors of poly(l‐latic acid)

The important practical problem of poor heat stability of poly(l ‐lactic acid) (PLLA) is addressed by the addition of N, N′‐bis (benzoyl) sebacic acid dihydrazide (BSAD) and talc as a nucleating agent system. The idea of incorporating talc into the PLLA/BSAD composites is that talc can provide supplementary nucleation effect with very small amount of BSAD (0.2 wt %) and therefore can improve the heat deflection resistance of PLLA materials. Effects of BSAD/talc on morphology, crystallization behavior, heat resistance, and mechanical properties of PLLA/BSAD/talc were investigated after annealing processes. The results indicated that the BSAD/talc system increased the crystallinity from 6.0% of pure PLLA to a maximum 42.9% by the synergistic effects of BSAD and talc increasing the growth of spherulites and nucleation density, respectively. After annealing at different temperatures, the heat deflection temperature (HDT) of PLLA was improved dramatically due to synergistic effects of BSAD/talc between restricted chain movement and acceleration of crystallization. At high temperature (above T_g), the thermo‐mechanical properties of PLLA is mainly determined by the crystallinity and the reinforcement effect of talc acted as a filler. Moreover, effects of BSAD/talc on mechanical properties were discussed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41454.     

Controlled crystal nucleation in the melt-crystallization of poly(l-lactide) and poly(l-lactide)/poly(d-lactide) stereocomplex

Among the various inorganic nucleators examined, Talc and an aluminum complex of a phosphoric ester combined with hydrotalcite (NA) were found to be effective for the melt-crystallization of poly(l-lactide) (PLLA) and PLLA/poly(d-lactide) (PDLA) stereo mixture, respectively. NA (1.0 phr (per one hundred resin)) can exclusively nucleate the stereocomplex crystals, while Talc cannot suppress the homo crystallization of PLLA and PDLA in the stereo mixture. Double use of Talc and NA (in 1.0 phr each) is highly effective for enhancing the crystallization temperature of the stereo complex without forming the homo crystals. The stereocomplex crystals nucleated by NA show a significantly lower melting temperature (207 °C) than the single crystal of the stereocomplex (230 °C) in spite of recording a large heat of crystallization ΔH_c (54 J/g). Photomicrographic study suggests that the spherulites with a symmetric morphology are formed in the stereo mixture added with NA while the spherulites do not grow in size in the mixture added with Talc. The exclusive growth of the stereocomplex crystals by the melt-crystallization process will open a processing window for the PLLA/PDLA.     

Study of thermomechanical,structural and antibacterial properties of poly(lactic acid) reinforced with graphene oxide nanoparticles via melt mixing

Addition of graphene oxide (GO) to poly(l ‐lactic acid) (PLLA) offers an alternative approach for tuning its crystallinity, improving its mechanical properties and transfusing an antibacterial behavior. GO/PLLA nanocomposites were prepared by melt extrusion, thus avoiding the potentially toxic, for biomedical applications, residue of organic solvents. Fourier transform infrared spectroscopy verified the formation of intermolecular hydrogen bonds. Using differential scanning calorimetry experiments concerning the isothermal crystallization of PLLA and PLLA containing 0.4 wt% GO, a two‐dimensional disc‐like geometry of crystal growth was determined, whereas at 125 and 130 °C the nanocomposite developed three‐dimensional spherulitic growth. Higher crystallization rate constant values suggest that the incorporation of 0.4 wt% GO accelerated the crystallization of PLLA. The lowest crystallization half‐time for PLLA was observed at 115 °C, while at 110 °C GO caused its highest decrease, accompanied by the highest increase in melting enthalpy (ΔH_m), as compared to that of PLLA, after completion of isothermal crystallization. Their ΔH_m values increased with T_ic, whereas multiple melting peaks transited to a single one with increasing T_ic. GO improved the PLLA thermal stability, tensile strength and Young's modulus. Incorporation of 0.8 wt% GO endowed PLLA with another potential application as a biomaterial since the derived composite presented good thermomechanical properties and effective prohibition of Escherichia coli bacteria attachment and proliferation. This effect was more prominent under simulated sunlight exposure than in the dark. The preparation method did not compromise the intrinsic properties of GO. © 2020 Society of Chemical Industry