Electrochemical capacitor composed of doped polyaniline and polymer electrolyte membrane

We prepared polyaniline doped with LiPF₆ and HCl, respectively, using chemical methods. The electrode composite was attached to both sides of Al mesh, while the polymer electrolyte mixture was spread on a glass plate. Then, the polyaniline‐based redox supercapacitor was fabricated using two electrodes and a polymer electrolyte membrane. The electrochemical performance of the redox supercapacitor was investigated by using the charge/discharge method, cyclic voltometry, and impedance spectroscopy. The initial specific capacitance was ≈115 F/g and it retained ≈90 F/g even after 5000 cycles. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1300–1304, 2003     

Preparation of polymer electrolytes based on the polymerized imidazolium ionic liquid and their applications in lithium batteries

The polymer electrolytes based on a polymerized ionic liquid (PIL) as polymer host and containing 1,2‐dimethyl‐3‐butylimidazolium bis(trifluoromethanesulfonyl)imide (BMMIM‐TFSI) ionic liquid, lithium TFSI salt, and nanosilica are prepared. The PIL electrolyte presents a high ionic conductivity, and it is 1.07 × 10^?3 S cm^?1 at 60°C, when the BMMIM‐TFSI content reaches 60% (the weight ratio of BMMIM‐TFSI/PIL). Furthermore, the electrolyte exhibits wide electrochemical stability window and good lithium stripping/plating performance. Preliminary battery tests show that Li/LiFePO₄ cells with the PIL electrolytes are capable to deliver above 146 mAh g^?1 at 60°C with very good capacity retention. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40928.     

New all solid‐state polymer electrolyte based on epoxy resin and ionic liquid for high temperature applications

Flexible epoxy network loaded with high amount of ionic liquid (IL) 1‐decyl‐3‐methylimidazolium bromide ([DMIM]Br) has been reported by using a mixture of polyol amine as curing agent. The IL presents good electrochemical response even at 170 °C, as no evidence of redox reactions was observed. The incorporation of as high as 50 wt % of this IL within the epoxy matrix resulted in solid and flexible electrolyte with good thermal stability below 180 °C, as measured by thermogravimetric analysis and ionic conductivity of around 10^?6 S cm^?1 at room temperature and higher than 10^?3 S cm^?1 at high temperature. This electrolyte presented a prodigious potential for applications in electrochemical devices at high temperature like batteries and supercapacitors, and the flexibility of this solid electrolyte persist at low temperature because of its low glass transition temperature. Furthermore, leakage problems were not observed. Thereby, impedance spectroscopy and cyclic voltammetry were performed to characterize the electrochemical properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45838.     

Multifunctional polyaniline–tin oxide (PANI–SnO2) nanocomposite: Synthesis,electrochemical, and field emission investigations

Synthesis of PANI–SnO₂ nanocomposite has been performed using a simple two step chemical oxidative polymerization route. The structural, morphological and chemical properties of the as‐synthesized PANI–SnO₂ nanocomposite have been revealed by various characterization techniques such as SEM, TEM, XRD, FTIR, and XPS. Interestingly the as‐synthesized PANI–SnO₂ nanocomposite exhibits supercapacitance value of 721 F g^?1 with energy density 64 Wh kg^?1, which is noticed to be higher than that of pristine SnO₂ and PANI nanostructures. Furthermore, the galvanostatic charge–discharge characteristics revealed pseudocapacitive nature of the PANI–SnO₂ nanocomposite. The estimated values of charge transfer resistance and series resistance estimated from the Nyquist plot are found to be lower. Along with the supercapacitive nature, PANI–SnO₂ nanocomposite showed promising field emission behavior. The threshold field, required to draw emission current density of 1 μA/cm², is observed to be 0.90 V/μm and emission current density of 1.2 mA/cm² has been drawn at applied field of ～2.6 V/μm. The emission current stability investigated at preset values of 0.02 and 0.1 mA/cm² is observed to be fairly stable over duration of more than 3 h. The enhanced supercapacitance values, as well as, the promising field emission characteristics are attributed to the synergic effect of SnO₂ nanoparticles and PANI nanotubes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41401.     

Electrochemical synthesis and In situ spectroelectrochemistry of conducting NMPy‐TiO2 and ZnO polymer nanocomposites for Li secondary battery applications

Poly(N‐methylpyrrole) (PNMPy), poly(N‐methylpyrrole‐TiO₂) (PNMPy‐TiO₂), and poly (N‐methylpyrrole‐ZnO) (PNMPy‐ZnO) nanocomposites were synthesized by in situ electropolymerization for cathode active material of lithium secondary batteries. The charge–discharging behavior of a Li/LiClO₄/PNMPy battery was studied and compared with Li/LiClO₄/PNMPy‐nanocomposite batteries. The nanocomposites and PNMPy films were characterized by cyclic voltammetry, in situ resistivity measurements, in situ UV–visible, and Fourier transform infra‐red (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The differences between redox couples (ΔE) were obtained for polymer nanocomposites and PNMPy films. During redox scan, a negative shift of potential was observed for polymer nanocomposite films. Significant differences from in situ resistivity of nanocomposites and PNMPy films were obtained. The in situ UV–visible spectra for PNMPy and polymer nanocomposite films show the intermediate spectroscopic behavior between polymer nanocomposites and PNMPy films. The FTIR peaks of polymer nanocomposite films were found to shift to higher wavelengths in PNMPy films. The SEM and TEM micrographs of nanocomposite films show the presence of nanoparticle in PNMPy backbone clearly. The result suggests that the inorganic semiconductor particles were incorporated in organic conducting PNMPy, which consequently modifies the properties and morphology of the film significantly. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41526.     

Morphology,crystallinity, and electrochemical properties of in situ formed poly(ethylene oxide)/TiO2 nanocomposite polymer electrolytes

A method to produce nanocomposite polymer electrolytes consisting of poly(ethylene oxide) (PEO) as the polymer matrix, lithium tetrafluoroborate (LiBF₄) as the lithium salt, and TiO₂ as the inert ceramic filler is described. The ceramic filler, TiO₂, was synthesized in situ by a sol–gel process. The morphology and crystallinity of the nanocomposite polymer electrolytes were examined by scanning electron microscopy and differential scanning calorimetry, respectively. The electrochemical properties of interest to battery applications, such as ionic conductivity, Li⁺ transference number, and stability window were investigated. The room‐temperature ionic conductivity of these polymer electrolytes was an order of magnitude higher than that of the TiO₂ free sample. A high Li⁺ transference number of 0.51 was recorded, and the nanocomposite electrolyte was found to be electrochemically stable up to 4.5 V versus Li⁺/Li. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2815–2822, 2003     

Molecularly imprinted electrochemical sensor for the determination of ampicillin based on a gold nanoparticle and multiwalled carbon nanotube‐coated pt electrode

A novel molecularly imprinted electrochemical sensor was developed for the sensitive and selective determination of ampicillin (AMP). The sensor was prepared on a platinum electrode modified with multiwalled carbon nanotubes (MWCNTs), gold nanoparticles (AuNPs), and a thin film of molecularly imprinted polymers (MIPs). MWCNTs and AuNPs were introduced to enhance the sensor's electronic transmission and sensitivity. The molecularly imprinted polymer (MIP) was synthesized using AMP as the template molecule, methacrylic acid as functional monomer, and ethylene glycol maleic rosinate acrylate (EGMRA) as cross‐linker. The performance of the proposed imprinted sensor was investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). The results showed that the imprinted film displayed a fast and sensitive response to AMP. Under optimal conditions, response peak current had a linear relationship with the concentration of AMP in the range of 1.0 × 10^?8 mol/L to 5.0 × 10^?6 mol/L and a detection limit of 1.0 × 10^?9 mol/L (S/N = 3). This imprinted sensor was used to detect AMP in food samples with recoveries of 91.4–105%. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40613.     

POSS‐based fluorinated azobenzene‐containing polymers: Photo‐responsive behavior and evaluation of water repellency

The photoresponsive polyhedral oligomeric silsesquioxanes (POSS) based fluorinated azobenzene‐containing polymers were prepared and characterized by NMR, FT‐IR, GPC, XRD, TG and UV–Vis spectra. The thermal property of the polymers was improved by the introduction of POSS cage. The trans‐cis photoisomerization of the polymers in solution was similar to that of the fluorinated azobenzene monomer and in accordance with the first‐order reaction kinetics equation within the first 250 seconds UV irradiation. The cotton fabrics coated with the polymers showed excellent water repellency and possessed switchable wettability under UV irradiation. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43540.     

Effect of propylene carbonate on the ionic conductivity of polyacrylonitrile‐based solid polymer electrolytes

Solid polymer electrolyte membranes consisting of polyacrylonitrile (PAN) as a host polymer, ammonium nitrate (NH₄NO₃) as a complexing salt, and propylene carbonate (PC) as a plasticizer were prepared by a solution casting technique. An increase in the amorphous nature of the polymer electrolytes was confirmed by X‐ray diffraction analysis. A shift in the glass‐transition temperature of the PAN/NH₄NO₃/PC electrolytes was observed in the differential scanning calorimetry thermograms; this indicated interactions between the polymer and the salt. The impedance spectroscopy technique was used to study the mode of ion conduction in the plasticized polymer electrolyte. The highest ionic conductivity was found to be 7.48 × 10^?3 S/cm at 303 K for 80 mol % PAN, 20 mol % NH₄NO₃, and 0.02 mol % PC. The activation energy of the plasticized polymer electrolyte (80 mol % PAN/20 mol % NH₄NO₃/0.02 mol % PC) was found to be 0.08 eV; this was considerably lower than that of the film without the plasticizers. The dielectric behavior of the electrolyte is discussed in this article. A literature survey indicated that the synthesis and characterization of ammonium‐salt‐doped, proton‐conducting polymer electrolytes based on PAN has been rare. The use of the best composition membrane (80 mol % PAN/20 mol % NH₄NO₃/0.02 mol % PC) proton battery was constructed and evaluated. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41743.     

Effects of morphology on the electrochemical performance of NiFe2O4 nanoparticles with battery-type behavior

We report the synthesis of NiFe₂O₄ nanoparticles by the complexation EDTA-citrate method under acidic (pH = 3) and basic (pH = 9) conditions. The structural, optical, vibrational, magnetic, and electrochemical properties were studied. The samples have crystallite sizes of 21 nm (pH 3) and 73 nm (pH 9), with rounded particles and layered structures. The ⁵⁷Fe Mössbauer spectra at 12 K showed that both samples had an inverse spinel cation distribution. At 5 K, the sample prepared at pH 9 showed saturation magnetizations of about 50 emu/g. Raman spectra showed typical bands of NiFe₂O₄ phase. The materials were tested as electrodes under alkaline condition. The cyclic voltammetry and charge-discharge experiments indicated a battery-type behavior, with maximun capacities of 65 and 5 C/g (at specific currents of 3 and 10 A/g) for samples prepared at pH 9 and 3, respectively. This work offers a route for obtaining NiFe₂O₄ nanoparticles with different morphologies and sizes tuned by the synthesis conditions.     

Effect of octa(epoxycyclohexyl) POSS on thermal,rheology property,and foaming behavior of PLA composites

Foams of poly(lactic acid) (PLA)/octa(epoxycyclohexyl) polyhedral oligomeric silsesquioxanes (ePOSS) composite were prepared by melt‐mixing and solid‐state foaming methods. A systematic and accurate method was applied to evaluate the effects of epoxy‐based POSS on the structure of dispersion, thermal behavior, and rheological properties of PLA composites. The application of secondary electron–electron back‐scattered diffraction technique was used to observe the cellular micromorphology and micro‐phase dispersion in composite foams, simultaneously. The results indicated that secondary dispersion of POSS aggregates occurred in foaming process. The enhanced melt elasticity, dispersity of POSS, and crystallization morphology of PLA/POSS composite had a significant effect on the controlling foaming behavior. Thus, a homogeneous and finer cellular morphology of PLA/POSS composite foam with high expansion ratio was obtained with a proper content of POSS in the composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46399.     

电解质对TiO2和ZnO光催化性能的影响

利用P25型纳米TiO₂和共沉淀法制备的纳米ZnO粉体，在紫外灯（主波长365 nm）照射下，以罗丹明B(Rh-B)为目标降解物，研究催化剂用量、电解质（SO^2-₄、Cl^-和NO^-₃）对TiO₂和ZnO催化降解罗丹明B的影响。结果发现,SO^2-₄促进光催化反应进行，Cl^-对反应有抑制作用，而NO^-₃对反应无明显影响。     

Effect of nano‐TiO2 dispersion on PEO polymer electrolyte property

Polymer electrolyte membranes based on poly(ethylene oxide) (PEO) doped with TiO₂ nanoparticles were synthesized by simple solution cast technique. Mesoporous TiO₂ film was prepared by doctor‐blade method. The modified polymer membranes and the mesoporous films were characterized by SEM, TEM, AFM, ionic conductivity, and J‐V measurements. Dye‐sensitized solar cells (DSSC) have been fabricated in which PEO‐polymer electrolyte doped with and without nano‐TiO₂ were sandwiched between porous TiO₂ and counter electrodes. The DSSC with nano‐TiO₂ doped polymer electrolyte shows better performance (1.68%) in comparison with pristine polymer electrolyte (1.07%), which is due to improved ionic conductivity value in polymer electrolyte system by nano‐TiO₂ doping. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and ionic conductivity of solid polymer electrolyte based on polyacrylonitrile‐polyethylene oxide

The transparent and flexible solid polymer electrolytes (SPEs) were fabricated from polyacrylonitrile‐polyethylene oxide (PAN‐PEO) copolymer which was synthesized by methacrylate‐headed PEO macromonomer and acrylonitrile. The formation of copolymer is confirmed by Fourier‐transform infrared spectroscopy (FTIR) measurements. The ionic conductivity was measured by alternating current (AC) impedance spectroscopy. Ionic conductivity of PAN‐PEO‐LiClO₄ complexes was investigated with various salt concentration, temperatures and molecular weight of PEO (Mn). And the maximum ionic conductivity at room temperature was measured to be 3.54 × 10^?4 S/cm with an [Li⁺]/[EO] mole ratio of about 0.1. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 461–464, 2006     

Synthesis and characterization of PLA nanocomposites containing nanosilica modified with different organosilanes I. Effect of the organosilanes on the properties of nanocomposites: Macromolecular,morphological, and rheologic characterization

Polylactide nanocomposites containing different loadings of nanosilica were prepared by employing bulk ring opening polymerization from lactide. Nanosilica was used as such and after surface treatment with different amounts of two distinct silanes. The effects on the properties of the material were evaluated comparing the samples containing organosilane‐modified nanosilica with poly(lactic acid) (PLA) containing unmodified nanosilica. A standard linear PLA and an industrial “film grade” PLA (PLA Natureworks 4032D) were used as reference. Pure silica tends to decrease the molecular weight of the material, deactivating the catalytic system but when silanes are present on the surface, molecular weights are similar to the ones of standard and industrial PLA. Transmission electron microscopy analysis shows that silanes improve the dispersion of the mineral, while rheologic curves suggest that when silanes are present melt viscosity increases markedly at zero shear and decreases faster as the shear rate increases. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphological,infrared, and ionic conductivity studies of poly(ethylene oxide)–49% poly(methyl methacrylate) grafted natural rubber–lithium perchlorate salt based solid polymer electrolytes

The potential of poly(ethylene oxide) (PEO) and 49% poly(methyl methacrylate) grafted natural rubber (MG49) as a polymer host in solid polymer electrolytes (SPE) was explored for electrochemical applications. PEO–MG49 SPEs with various weight percentages of lithium perchlorate salt (LiClO₄) was prepared with the solution casting technique. Characterization by scanning electron microscopy, Fourier transform infrared spectroscopy, and impedance spectroscopy was done to investigate the effect of LiClO₄ on the morphological properties, chemical interaction, and ionic conductivity behavior of PEO–MG49. Scanning electron microscopy analysis showed that the surface morphology of the sample underwent a change from rough to smooth with the addition of lithium salts. Infrared analysis showed that the interaction occurred in the polymer host between the oxygen atom from the ether group (C? O? C) and the Li⁺ cation from doping salts. The ionic conductivity value increased with the addition of salts because of the increase in charge carrier up to the optimum value. The highest ionic conductivity obtained was 8.0 × 10^?6 S/cm at 15 wt % LiClO₄. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Measurement of the electrochemical response time and electron paramagnetic resonance behavior of poly(o‐phenetidine)–poly(styrene sulfonic acid) and poly(2‐ethylaniline)–poly(styrene sulfonic acid) complexes

Two studies were mainly focused on the measurement of electrochemical response time and the electron paramagnetic resonance (EPR) of the substituted polyaniline (PANI) complexes poly(o‐phenetidine) (POP)–poly(styrene sulfonic acid) (PSSA) and poly(2‐ethylaniline) (P2E)–PSSA, which were prepared by the electrochemical polymerization of the monomer (o‐phenetidine or 2‐ethylaniline) with PSSA, with indium tin oxide (ITO) as a working electrode in a 1M HCl solution. Ultraviolet–visible spectra measurements showed evidence for the doped substituted PANI system to have a highly electrochemical response time recorded at a temperature of 298 K, and the results were further analyzed on the basis of the color–discolor model, which is typical of protonation systems. At the reaction time (3 s) and monomer concentration (0.6M) with PSSA (0.15 μ), the best electrochemical color/discolor time of the POP–PSSA complexes was 125/125 ms (thickness = 3.00 μm), which was faster than that of the P2E–PSSA complexes. At the same thickness (10 μm), the best electrochemical color/discolor time of the POP–PSSA complexes was 500/250 ms, which was faster than the P2E–PSSA complexes (750/500 ms). With regard to film growth rate, the POP–PSSA complexes (1.0 μm/s) were faster than the P2E–PSSA complexes (0.79 μm/s); this was attributed to the substituted PANI having a steric effect and to good reactivity by the ethoxy group (? OC₂H₅) in the molecules. The EPR spectra of the two samples were recorded both at 298 and 77 K and were further analyzed on the basis of the polaron–bipolaron model. The narrower line width of the substituted PANI complexes arose due to polarons; that is, we propose that charge transport took place through both polarons and bipolarons. Compared to their salts, this could be attributed to the lower degree of structural disorder, the oxygen absorption on the molecules, and the steric effect by the side chain group. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1211–1221, 2005     

Preparation and ionic conductive properties of all‐solid polymer electrolytes based on multiarm star block polymers

A series of star block polymers with a hyperbranched core and 26 arms are successfully synthesized by atom transfer radical polymerization of styrene (St), and poly(ethylene glycol) methyl ether methacrylate from a hyperbranched polystyrene (HBPS) multifunctional initiator. All‐solid polymer electrolytes composed of these multiarm star polymers and lithium salts are prepared. The influences of polyoxyethylene (PEO) side‐chain length, PEO content, lithium salt concentration and type, and the structure of polymer on ionic conductivity are systematically investigated. The resulting polymer electrolyte with the longest PEO side chains exhibits the best ionic conductive properties. The maximum conductivity is 0.8 × 10^?4 S cm^?1 at 25°C with EO/Li = 30. All the prepared multiarm star block polymers possess good thermal stability. The mechanical property is greatly improved owing to the existence of polystyrene blocks in the multiarm star polymer molecules, and flexible films can be obtained by solution‐casting technique. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of ZnO and TiO2 doping on the sintering behavior of Y2O3 ceramics

Full densification of Y₂O₃ is challenging and requires a very high sintering temperature (above 1700 °C). In this study, the effect of ZnO and TiO₂ dopants on its densification was investigated, showing that both dopants lowered the sintering temperature and improved the process. Moreover, ZnO promoted the grain growth, while TiO₂ inhibited it; hence, the ZnOTiO₂ co-doping and the change in the ZnO/TiO₂ ratio allowed the control of the sintered body microstructure while maintaining high densification. Since Y₂O₃ has a higher plasma erosion resistance than conventional Si-based materials, the plasma dry etching resistance of the sintered Y₂O₃ was also evaluated and found superior due to the improved densification and controlled grain size of the doped samples.