PTT非等温结晶动力学研究

采用差示扫描量热仪对PTT进行非等温结晶研究。利用不同动力学模型对其结晶过程进行处理, 并将PTT与PET及PBT的非等温结晶过程进行对比。结果表明:Jeziorny方程和Ozawa方程都可以很好的 描述PTT,PET,PBT的非等温结晶过程;采用结合Avrami方程和Ozawa方程的处理方法,得到了3种聚酯的 结晶速率的大小关系:PBT>PTT>PET。通过计算Ziabicki结晶能力参数,得到3种聚酯的结晶能力的顺序 为:PBT>PTT>PET。     

Crystal morphology and nonisothermal crystallization kinetics of short carbon fiber/poly(trimethylene terephthalate) composites

The crystal morphology and nonisothermal crystallization kinetics of short carbon fiber/poly(trimethylene terephthalate) (SCF/PTT) composites were investigated by polarized optical microscopy (POM) and differential scanning calorimetry (DSC). The optical micrographs suggest that the more content of SCF in composites, the smaller size of the spherulites is. Moreover, the addition of SCF can lead to forming banded spherulites in composites. The Avrami equation modified by Jeziorny, Ozawa theory and the method developed by Mo were used, respectively, to fit the primary stage of nonisothermal crystallization of various composites. The results suggest that the SCF served as nucleation agent, accelerates the crystallization rate of the composites, and the more content of SCF, the faster crystallization rate is. Effective activation energy calculated by the differential iso‐conversional method developed by Friedman also concludes that the composite with more SCF component has higher crystallization ability than that with less SCF content. The kinetic parameters U* and K_g are determined, respectively, by the Hoffman–Lauritzen theory. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

聚乙二醇增塑聚乳酸的非等温结晶动力学研究

采用DSC方法对聚乙二醇(PEG)增塑聚乳酸的非等温结晶动力学进行了研究。结果表明,PEG的加入明显提高了聚乳酸的结晶速度。对所得数据分别用Ozawa方程和莫志深方法进行了处理,发现在给定温度范围里非等温结晶时,PLA/PEG主要是以均相成核的三维生长方式结晶;PLA的结晶速度随着PEG分子质量的增加而升高。     

聚丁二酸丁二醇酯/聚乙二醇硬脂酸酯共混物非等温结晶行为

以聚丁二酸丁二醇酯（PBS）和聚乙二醇硬脂酸酯（PEOST）为原料,采用溶液共混法制备了PEOST质量分数分别为10%（POS-10）和30%（POS-30）的两种合金材料。通过差示扫描量热法（DSC）研究了合金材料的非等温结晶行为,用莫志深（Mo）法分析了PBS的非等温结晶动力学,采用Kissinger法和Friedman法计算PBS的结晶活化能,并用红外（FTIR）和偏光显微镜（POM）进行表征。研究结果表明：PBS先结晶形成结晶微区不利于PEOST结晶,而较高含量的PEOST有利于PBS的结晶。受PBS先结晶的影响,POS-10降温DSC曲线没有出现PEOST的结晶峰,而POS-30在低的降温速率情况下出现了PEOST双结晶峰;升温DSC曲线中两试样均出现了PEOST的熔融峰。在相同的冷却速率下,POS-30的PEOST熔融温度（T_m）和熔融焓（△H_m）大于POS-10;POS-30的PBS结晶峰温度（T_p）、结晶焓（△H_c）大于POS-10,而结晶半峰宽（D）值更小;但两者的T_m和△H_m相当。随冷却速率的增加,PBS的D值增大,而PEOST的D值却降低;冷却速率的增加对PBS的T_m值影响不大,但使PEOST的T_m略有减小。Mo法适合用于共混物中PBS的非等温结晶动力学分析。POS-30的PBS绝对值结晶活化能要大于POS-10。POS-30在红外光谱谱图中出现了PEOST结晶的红外响应峰（1109cm^-1和841cm^-1）而POS-10没有。     

Two courses in the nonisothermal primary crystallization of poly(butylene terephthalate)

Nonisothermal crystallization behavior of poly(butylene terephthalate) (PBT) was investigated by means of differential scanning calorimetry. The nonisothermal crystallization kinetic process was analyzed and relative kinetic parameters were obtained with the Avrami and Liu–Mo equations. The results demonstrate a heterogeneous nucleation mechanism. It was found that the nonisothermal primary crystallization of PBT was composed of two courses. Course I corresponded to the two‐dimensional formation process of the lamellae, and the corresponding relative crystallinity (X_t) was less than 15%. Course II was concerned with the three‐dimensional growth process of the spherulite, and X_t changed from 15 to 90%. The secondary crystallization began when X_t was greater than 90%. According to the Flynn–Wall–Ozawa equation, the activation energies for course I, course II, and secondary crystallization were calculated to be ?120, ?210, and ?100 kJ/mol, respectively. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Application of nonisothermal cure kinetics to the interaction of poly(ethylene terephthalate) with alkyd resin varnish

Linear and nonlinear viscoelasticity of an adhesion material for integrated circuit chips were investigated to control the processability. The material consists of acrylic polymer (AP) and epoxy oligomer (EP). EP content in AP/EP blend is 70 vol %. From the linear viscoelasticity, it was found that the iso‐free volume state of AP/EP blend was 20°C lower than that of AP and the entanglement molecular weight M_e of AP/EP was three times higher than that of AP. Nonlinear stress relaxation modulus G(t,γ) showed that the time‐strain separability, G(t,γ) = G(t)h(γ), was applicable at long time above a characteristic time τ_k, where G(t) is linear relaxation modulus and h(γ) is the damping function. The τ_k value was estimated to be 10 s for AP/EP and below 0.1 s for AP at an iso‐free volume state. (h(γ) for AP and AP/EP behaved like a usual linear homopolymer.) The time evolution of the elongational viscosity η_E(t) of each sample showed that AP/EP system exhibited strong strain hardening at , although AP did not show strain hardening at strain rate measured, when the data were compared at an iso‐free volume state. These results strongly suggest that the strain hardening behavior of AP/EP is attributable to enhancement of the stretch of AP polymer chains by diluting EP oligomer chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Non‐isothermal crystallization kinetics and melting behaviors of poly(butylene succinate) and its copolyester modified with trimellitic imide units

With the help of differential scanning calorimeter (DSC), the basic thermal behaviors, nonisothermal crystallization kinetics, and subsequent melting behaviors of poly(butylene succinate) (PBS) and its copolyester (PBSTMA) modified with trimellitic imide units were investigated in this paper. The DSC thermograms of PBS and PBSTMA showed that the crystallization behaviors of PBS were affected seriously because of the addition of a small quantity of trimellitic imide units. The nonisothermal crystallization processes of them were represented by the Avrami equation modified by Jeziorny and the method developed by Ozawa. After that, the conception of “crystallization rate coefficient (CRC)” introduced by Khanna was employed. The values of CRC for PBS and PBSTMA are 174.6 and 88.2 h^–1, respectively. At the end of this paper, the melting behaviors of PBS and PBSTMA after being cooled from 130 to 30°C at different cooling rate were studied in detail. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2493–2499, 2006     

Miscibility and crystallization of poly(ethylene succinate)/poly(vinyl phenol) blends

Miscibility of biodegradable poly(ethylene succinate) (PES)/poly(vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) in this work. PES is found to be miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. Spherulitic morphology and the growth rates of neat and blended PES were investigated by optical microscopy (OM). Both neat and blended PES show a maximum growth rate value in the crystallization temperature range of 45-65 °C, with the growth rate of neat PES being higher than that of blended PES at the same crystallization temperature. The overall crystallization kinetics of neat and blended PES was also studied by DSC and analyzed by the Avrami equation at 60 and 65 °C. The crystallization rate decreases with increasing the temperature for both neat and blended PES. The crystallization rate of blended PES is lower than that of neat PES at the same crystallization temperature. However, the Avrami exponent n is almost the same despite the blend composition and crystallization temperature, indicating that the addition of PVPh does not change the crystallization mechanism of PES but only lowers the crystallization rate.     

Synthesis of novel biodegradable poly(butylene succinate) copolyesters composing of isosorbide and poly(ethylene glycol)

A series of biodegradable isosorbide‐based copolyesters poly(butylene succinate‐co‐isosorbide succinate‐co‐polyethyleneoxide succinate) (PB_xI_yE_zS) were synthesized via bulk polycondensation in the presence of dimethyl succinate (DMS), 1,4‐butanediol (BDO), poly(ethylene glycol) (PEG) and isosorbide (ISO). The crystallization behaviors, crystal structure and spherulite morphology of the copolyesters were analyzed by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and polarizing optical microscopy (POM), respectively. The results indicate that the crystallization behavior of the copolyesters was influenced by the content of isosorbide succinate (IS) and polyethyleneoxide succinate (PEOS) units, which further tuned the mechanical and biodegradable properties of the copolyesters. The PB_xI_yE_zS copolyesters, compared to pure poly(butylene succinate), showed lower crystallization temperature, melting temperature, degree of crystallinity and degradation rate while a significant increase in glass transition temperature with increasing isosorbide content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

PTT的非等温结晶动力学研究

采用DSC方法对PTT在不同冷却速率下的结晶过程进行了研究,并与PET进行了对比,其结晶动力学用Mandel Kern方法来处理。结果表明,PTF相对于PET更易成核结晶,PTT半结晶时间比PET长,冷却速率对PTT的半结晶时间影响大,并且PTF的非等温结晶动力学曲线的线性较PET好,能够更好的遵循Mandel Kern方法。     

Effect of photofunctional organo anion-intercalated layered double hydroxide nanoparticles on poly(ethylene terephthalate) nonisothermal crystallization kinetics

Very recently, we report a facile preparation and strong UV-shielding function of poly(ethylene terephthalate) (PET) nanocomposites using 4,4′-diaminostilbene-2,2′-disulfonic acid anion-intercalated layered double hydroxide (LDH_DDA). Herein, the effect of the photofunctional organo anion-intercalated LDH nanoparticles on nonisothermal crystallization kinetics of PET is reported by differential scanning calorimetry technique. First, the nonisothermal crystallization behaviour is discussed by several basic parameters including crystallization peak temperature, relative degree of crystallinity with temperature or time, and half-time of crystallization. Then, Avrami and Jeziorny method, as well as Mo model were applied for the PET/LDH_DDA nanocomposites. Finally, the crystallization activation energy was investigated by Kissinger method and Flynn conversion. The results reveal that the incorporation of LDH_DDA nanoparticles acted as nucleating agent and significantly accelerated the PET nonisothermal crystallization process, whereas had little effect on the three-dimensional growth pattern of spherulites.     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)等温结晶行为研究

以对苯二甲酸(PTA)、乙二醇(EG)、异山梨醇(ISB)为原料,通过直接熔融缩聚法合成聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)(PEIT)共聚酯。利用差示扫描量热法(DSC)研究了共聚酯的结晶行为,采用Avrami方程分析了共聚酯的等温结晶动力学。结果表明,PEIT共聚酯结晶行为受共聚组成和结晶温度影响。随着ISB用量的增加或结晶温度的降低,共聚酯半结晶周期t1/2增加、结晶速率变慢;ISB摩尔分数超过20%,共聚酯无法结晶。     

Melting,crystallization behaviors,and nonisothermal crystallization kinetics of PET/PTT/PBT ternary blends

The melting, crystallization behaviors, and nonisothermal crystallization kinetics of the ternary blends composed of poly(ethylene terephthalate), poly(trimethylene terephthalate) (PTT) and poly(buthylene terephthalate) (PBT) were studied with differential scanning calorimeter (DSC). PBT content in all ternary blends was settled invariably to be one‐third, which improved the melt‐crystallization temperature of the ternary blends. All of the blend compositions in amorphous state were miscible as evidenced by a single, composition‐dependent glass transition temperature (T_g) observed in DSC curves. DSC melting thermograms of different blends showed different multiple melting and crystallization peaks because of their various polymer contents. During melt‐crystallization process, three components in blends crystallized simultaneously to form mixed crystals or separated crystals depending upon their content ratio. The Avrami equation modified by Jeziorny and the Ozawa theory were employed to describe the nonisothermal crystallization process of two selected ternary blends. The results spoke that the Avrami equation was successful in describing the nonisothermal crystallization process of the ternary blends. The values of the t_1/2 and the parameters Z_c showed that the crystallization rate of the ternary blends with more poly(ethylene terephthalate) content was faster than that with the lesser one at a given cooling rate. The crystal morphology of the five ternary blends investigated by polarized optical microscopy (POM) showed different size and distortional Maltese crosses or light spots when the PTT or poly(ethylene terephthalate) component varied, suggesting that the more the PTT content, the larger crystallites formed in ternary blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

The complicated influence of branching on crystallization behavior of poly(ethylene terephthalate)

The randomly branched poly(ethylene terephthalate) (BPET) was prepared by bulk polycondensation from dimethyl terephthalate (DMT) and ethylene glycol (EG), with 0.4–5.0 mol % (with respect to DMT) of glycerol (GL) as a branching agent. The glass transition and crystallization behavior was studied by differential scanning calorimetry (DSC). It was found that the glass transition temperature of BPET reduced with the increasing content of GL until 1.2 mol %, and then increases a little at high degrees of branching. When compared with a linear PET, the crystallization temperature of BPET from the melt shifted to higher temperature as GL content was smaller than 1.2 mol %, and then became lower while GL load was added. Nonisothermal crystallization kinetics was studied through the modified Avrami analysis. It was revealed that the overall crystallization rate parameter of BPET became larger when the GL content was less than 1.2 mol %, then turned to lower at higher branching degree. This indicated that low degree of branching could enhance the overall crystallization of poly(ethylene terephthalate) (PET), whereas high degree of branching in the range of 3.5–5.0 mol % would block the development of crystallization. On the basis of Hoffman's secondary crystallization theory, the product σσ_e of the free energy of formation per unit area of the lateral and folding surface was calculated. According to the change of the product σσ_e with the degree of branching, a possible explanation was presented to illuminate this diverse effect of different degrees of branching on crystallization. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of shearing on crystallization behavior of poly(ethylene terephthalate)

The shear‐induced crystallization behavior of PET was investigated by measuring the time‐dependent storage modulus (G′) and dynamic viscosity (η′) with a parallel‐plate rheometer at different temperatures and shear rate. The morphology of shear‐induced crystallized PET was measured by DSC, X‐ray, and polarizing optical microscopy. When a constant shear rate was added to the molten polymer, the shear stress increased with the time as a result of the orientation of molecular chains. The induction time of crystallization is decreased with frequency. Moreover, the rate of isothermal crystallization of PET was notably decreased with increasing temperature. The shape of spherulites is changed to ellipsoid in the direction of shear. In addition, aggregation of spherulites is increased with increasing frequency. Particularly, the row nucleation morphology could be observed under polarized light for ω = 1. From the results of DSC, the melting point and enthalpy have a tendency to decrease slightly with increasing frequency. The crystallite size and perfectness decreased with frequency, which was confirmed with X‐ray data. The unit length of the crystallographic unit cell of the PET increased and the (1 0 3) plane peak increased with increasing frequency. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2640–2646, 2001     

Nonisothermal crystallization kinetics of poly(ethylene terephthalate) and poly(methyl methacrylate) blends

The nonisothermal crystallization kinetics of poly(ethylene terephthalate) (PET) and poly(methyl methacrylate) (PMMA) blends were studied. Four compositions of the blends [PET 25/PMMA 75, PET 50/PMMA 50, PET 75/PMMA 25, and PET 90/PMMA 10 (w/w)] were melt‐blended for 1 h in a batch reactor at 275°C. Crystallization peaks of virgin PET and the four blends were obtained at cooling rates of 1°C, 2.5°C, 5°C, 10°C, 20°C, and 30°C/min, using a differential scanning calorimeter (DSC). A modified Avrami equation was used to analyze the nonisothermal data obtained. The Avrami parameters n, which denotes the nature of the crystal growth, and Z_t, which represents the rate of crystallization, were evaluated for the four blends. The crystallization half‐life (t_½) and maximum crystallization (t_max) times also were evaluated. The four blends and virgin polymers were characterized using a thermogravimetric analyzer (TGA), a wide‐angle X‐ray diffraction unit (WAXD), and a scanning electron microscope (SEM). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3565–3571, 2006     

Synthesis, characterization, and properties of poly(ethylene terephthalate)/poly(1,4-butylene succinate) block copolymers

Reactive blending at 290 °C of a series of mixtures of poly(ethylene terephthalate) (PET) and poly(1,4-butylene succinate) (PBS) led to the formation of block PET/PBS copolyesters. The block lengths of the resulting copolymers decreased with the severity of the treatment. Copolyesters with PET/PBS molar compositions of 90/10, 80/20, 70/30, and 50/50 were prepared by this method and their composition and microstructure were characterized by ¹H and ¹³C NMR, respectively. The T_g, T_m, and crystallinity of the copolymers decreased as the content in PBS and the degree of randomness increased. The elastic modulus and tensile strength of the copolymers decreased with the content of PBS, whereas, on the contrary, the elongation at break increased. The PET/PBS copolymers exhibited a pronounced hydrolytic degradability, which increased with the content in 1,4-butylene succinic units. Hydrolysis mainly occurred on the aliphatic ester groups.     

On the triple melting behaviour of poly(ethylene succinate)

The morphology of melt-crystallized poly(ethylene succinate) (PES) was investigated by optical microscopy and scanning electron microscopy, and the melting behaviour of PES was studied by differential scanning calorimetry (DSC). At low crystallization temperature imperfect crystals were formed which could melt and recrystallize during the DSC scan. Triple melting peaks were observed, and the melting behaviour was strongly dependent on crystallization time and scan rate. It was observed that crystallization at high temperature perfected the crystals (dominant and subsidiary lamellae in the spherulitic structure). Increasing the scan rate reduced the chance for reorganization. However, at high crystallization temperature two melting peaks were observed. The material formed was much more perfect, so that the melting process was not dominated by recrystallization. Accordingly, the cause of dual melting is the existence of two kinds of crystal perfection.     

Isothermal crystallization kinetics and spherulite morphologies of poly(lactic acid)/ethylene acrylate copolymer blends

Isothermal crystallization kinetics and spherulite morphologies of partially immiscible blends of poly(lactic acid) (PLA) and ethylene acrylate copolymer (EAC) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy. The DSC data obtained was analyzed using the Avrami equation. Crystallization kinetics of PLA from the melt was strongly influenced by the blend composition and the crystallization temperature. At a given crystallization temperature, the overall crystallization rate value was greater in the blends than in PLA suggesting that the presence of EAC enhanced crystallization of PLA. Polarized optical micrographs showed that the crystallization of PLA initially took place at the PLA/EAC interface. At high EAC content (>1 wt %), EAC domains acted as hindrance to crystallization reducing the overall crystallization rate of PLA in the blends. Based on the DSC analysis, the crystallization rate was maximum when PLA blend with 1 wt % EAC was isothermally crystallized at 103 °C. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45487.