Effect of extruder type on the properties and morphology of reactive blends based on polyamides

The morphology and mechanical properties of polyamide-based blends prepared in single and corotating twin-screw extruders were compared using transmission electron microscopy (TEM) techniques. Reactive polyamide blends with SEBS-g-MA (a maleated styrenic triblock copolymer with ethylene–butvlene midblocks), EPR-g-MA (a maleated ethylene/propylene rubber), and ABS were selected for the purpose of this investigation. For blends of SEBS-g-MA with difunctional (nylon x,y) polyamides (e.g., nylon 6,6; nylon 12,12), the twin-screw extruder was more effective in producing a finer dispersion of the rubber phase, which resulted in a significant lowering of the ductile–brittle transition temperature in case of the nylon 6,6 blend. On the other hand, blends of SEBS-g-MA with the mono-functional nylon 6 material led to rubber particles that were too small for toughening for both extruder types employed in this work. For nylon 6/EPR-g-MA blends, the single-screw extruder led to blends with excellent low-temperature impact properties for both single-step and masterbatch mixing techniques, whereas nylon 6/EPR-g-MA blends prepared in a single-step operation in the twin-screw extruder were brittle under ambient conditions. For difunctional polyamide blends with ABS (compatibilized with an imidized acrylic polymer), the morphology and mechanical properties were found to be independent of the extruder type employed for processing. © 1994 John Wiley & Sons, Inc.     

Influence of thermoplastic elastomers on mechanical properties and morphologies of isotactic polypropene/glass bead hybrid composites

Glass bead-reinforced isotactic polypropene hybrid composites containing 0–20 vol % thermoplastic elastomers were prepared to study both structure/property relationship and morphology development. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS-g-MA) were used as thermoplastic elastomers. Hybrid composites containing SEBS gave higher Young's moduli than did those containing SEBS-g-MA. The experimental Young's moduli were in good agreement with the theoretical predictions according to Lewis and Nielsen. The lower moduli of hybrid composites containing SEBS-g-MA were attributed to interlayer formation and in situ encapsulation of glass beads, resulting in core–shell particles. This elastomeric interlayer impaired the filler reinforcement. Analysis of tensile yield stress and results of lap-shear tests confirmed strong filler–polymer interactions in composites containing SEBS-g-MA. Only in excess of a critical volume fraction did SEBS-g-MA afford a significant improvement of the notched Izod impact strength. In contrast to stiffness, Izod impact strength was not influenced by the type of elastomer and morphology. Investigation of crystallization and scanning electron microscopic studies proved the in situ encapsulation of the glass beads with SEBS-g-MA, whereas SEBS addition results in separately dispersed glass beads and SEBS microphases. © 1996 John Wiley & Sons, Inc.     

Influence of morphology on rheological and mechanical properties of SEBS-toughened,glass-bead-filled isotactic polypropene

The influence of morphology of glass-bead-filled isotactic polypropene containing 0–20 vol% thermoplastic elastomers (TPE) on mechanical and rheological properties was investigated. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene(SEBS) and the corresponding block copolymer grafted with maleic anhydrid (SEBS-g-MA) were used as thermoplastic elastomers, realizing, in the first case, a three-phase morphology with separately dispersed glass beads and SEBS particles. In the second case, SEBS-g-MA forms an elastomeric interlayer between glass beads and polypropene matrix, comprising core–shell particles. Young's modulus and tensile yield stress of the hybrid composites decrease with an increase in TPE volume fraction due to low stiffness and strength of TPE. In comparison with the three-phase morphology of hybrid composites with SEBS, SEBS-g-MA interlayers effect a reduced stiffness of the hybrid composites but improve interfacial adhesion and, thus, tensile yield stress. Rheological storage and loss moduli increase with an increase in glass bead and TPE volume fraction. Due to improved interfacial adhesion, melt elasticity and viscosity are enhanced by the SEBS-g-MA interlayer when compared with separately dispersed SEBS. Consequently, the reduced stiffening effect of the glass beads due to SEBS-g-MA interlayer decreases mechanical elasticity, whereas improved interfacial adhesion, also promoted by the SEBS-g-MA interlayer, enhances tensile yield stress and melt elasticity. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2499–2506, 1998     

Optimum toughening via a bicontinuous blending: toughening of PPO with SEBS and SEBS-g-maleic anhydride

The poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) was toughened by melt extrusion through its blending with a styrene-b-ethylene/butadiene-b-styrene triblock copolymer (SEBS), or with maleic anhydride (MA) grafted SEBS (SEBS-g-MA). Their morphology, mechanical properties, and rheology have been investigated. Transmission electron microscopy revealed that both kinds of blends had an island-sea structure at low concentrations of SEBS or SEBS-g-MA and a bicontinuous one at sufficiently high concentrations. However, the percolation threshold was higher for SEBS than for the SEBS-g-MA. The Izod impact strength of PPO could be significantly improved through its blending with SEBS-g-MA, particularly in a blend with 20 wt% of SEBS-g-MA at which it had a maximum value. The rheological experiments indicated that the incorporation of SEBS increased and that of SEBS-g-MA decreased the melt viscosity of the system.     

Effect of rubber particle size and rubber type on the mechanical properties of glass fiber reinforced, rubber-toughened nylon 6

The effects of rubber type and particle size on the mechanical properties of glass fiber reinforced blends of nylon 6 and EPR/EPR-gMA or SEBS/SEBS-g-MA were investigated; rubber particle size in the two systems could be controlled by varying the ratio of EPR to EPR-g-MA or SEBS to SEBS-g-MA. Unreinforced materials with the highest levels of toughness did not necessarily lead to the highest fracture energy when reinforced with 15 wt% glass fibers. Materials toughened with SEBS/SEBS-gMA, which are tougher in the absence of glass fibers had lower fracture energies when 15 wt% glass fibers are present. In general, smaller rubber particles led to higher fracture energies. Fracture analysis according to a modified essential work of fracture analysis reveals that SEBS/SEBS-g-MA have high values of the dissipative energy density, u_d, in the absence of glass fibers. When 15 wt% glass fibers are added, u_d is essentially zero for all the materials tested. The limiting specific fracture energy, u₀, on the other hand, was higher for both unreinforced and glass fiber reinforced EPR/EPR-g-MA toughened blends than for SEBS/SEBS-g-MA based materials. Transmission electron microscopy observations of fractured specimens indicate that glass fibers decrease the size of the damage zone of rubber toughened nylon 6. Shear yielding was seen in fractured specimens of reinforced nylon 6 blends containing either SEBS/SEBS-g-MA or EPR-g-MA, but the size of this shear yielded zone was larger for EPR/EPR-g-MA. In addition, EPR/EPR-g-MA based materials displayed craze-like deformations, while SEBS-g-MA materials did not exhibit this deformation process.     

The effects of SEBS-g-maleic anhydride reaction on the morphology and properties of polypropylene/PA6/SEBS ternary blends

Ternary blends, based on 70% by weight of polypropylene (PP) with 30% by weight of a dispersed phase, consisting of 15% polyamide-6 (PA6) and 15% of a mixture comprising varying ratios of an unreactive poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS) triblock copolymer and a reactive maleic anhydride-grafted SEBS-g-MA, were produced via melt blending in a co-rotating twin-screw extruder. TEM revealed the blend containing only non-reactive SEBS to exhibit individual PA6 and SEBS dispersed phases. However, the progressive replacement of SEBS with reactive SEBS-g-MA increased the degree of interfacial reaction between the SEBS and PA6 phases, thus reducing interfacial tension and providing a driving force for encapsulation of the PA6 by the SEBS. Consequently, the dispersed-phase morphology was observed to transform from two separate phases to acorn-type composite particles, then to individual core-shell particles and finally to agglomerates of the core-shell particles. The resultant blends exhibited significant morphology-induced variations in both thermal and mechanical properties. DSC showed that blends in which the diameter of the PA6 particles was reduced to ≤3 μm by the increasing interfacial reaction exhibited fractionated PA6 crystallisation. In general, mechanical testing showed the blends to exhibit inferior low-strain tensile properties (modulus and yield stress) compared to the matrix PP, but superior ultimate tensile properties (stress and strain at break) and impact strength. These changes are discussed with reference to composite models.     

Comparison of the toughening behavior of nylon 6 versus an amorphous polyamide using various maleated elastomers

The toughening effect of two types of elastomers based on ethylene/α-olefin copolymers, viz, an ethylene/propylene copolymer (EPR) with its maleated version, EPR-g-MA, and an ethylene/1-octene copolymer (EOR) with its maleated versions, EOR-g-MA-X% (X=0.35, 1.6, 2.5), for two classes of polyamides: semi-crystalline nylon 6 versus an amorphous polyamide (Zytel 330 from DuPont), designated as a-PA, was explored. The results are compared with those reported earlier based on a styrenic triblock copolymer having a hydrogenated midblock, SEBS, and its maleated version, SEBS-g-MA, elastomer system. Izod impact strength was examined as a function of rubber content, rubber particle size and temperature. All three factors influence the impact behavior considerably for the two polyamide matrices. The a-PA is found to require a somewhat lower content of rubber for toughening than nylon 6. Very similar optimum ranges of rubber particle sizes were observed for ternary blends of EOR-g-MA/EOR with each of the two polyamides while blends based on mixtures of EPR-g-MA/EPR and SEBS-g-MA/SEBS (where the total rubber content is 20% by weight) show only an upper limit for a-PA but an optimum range of particle sizes for nylon 6 for effective toughening. Higher EPR-g-MA contents lead to lower ductile-brittle transition temperatures (T_db) as expected; however, a-PA binary blends with EPR-g-MA have a much lower T_db than do nylon 6 blends when the content of the maleated elastomer is not high. A minimum in plots of ductile-brittle transition temperature versus particle size appears for ternary blends of each of the matrices with EOR-g-MA/EOR; blends based on SEBS-g-MA/SEBS, in most cases, show higher ductile-brittle transition temperatures, regardless of the matrix. However, blends with EPR-g-MA/EPR show comparable T_db with those based on EOR-g-MA/EOR for the amorphous polyamide but show the lowest ductile-brittle transition temperatures for nylon 6 within the range of particle sizes examined. For the blends with a bimodal size distribution, the global weight average rubber particle size is inappropriate for correlating the Izod impact strength and ductile-brittle transition temperature. In general, trends for this amorphous polyamide are rather similar to those of semi-crystalline nylon 6.     

Effects of electron beam irradiation on the structure–property behavior of blends based on low density polyethylene and styrene-ethylene-butylene-styrene-block copolymers

Low density polyethylene (LDPE) blends with different additives were exposed to various doses of electron beam irradiation. The additives used were styrene-ethylene-butylene-styrene-block copolymers (SEBS), styrene-ethylene-butylene-styrene-block copolymer grafted with maleic anhydride (SEBS-g-MA) and mineral compounds. The structure–property behavior of electron beam irradiated blends was characterized in terms of mechanical, thermal, and electrical resistivity properties. The results indicated that the unirradiated LDPE blends with the different compositions showed improved mechanical properties, thermal and volume resistivity properties than pure LDPE. However, the improvement in properties of unirradiated blends by using SEBS-g-MA was higher than using SEBS copolymer. Further improvement in the mechanical, thermal and electrical properties of the LDPE blends was achieved after electron beam irradiation. The limited oxygen index (LOI) data revealed that the LDPE/SEBS-g-MA/ATH blend was changed from combustible to self-extinguishing material after electron beam irradiation to a dose of 100 kGy. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Compatibilization of polyethylene terephthalate/polypropylene blends with styrene–ethylene/butylene–styrene (SEBS) block copolymers

Blends of polyethylene terephthalate (PET) and polypropylene (PP) at compositions 20/80 and 80/20 were modified with three different styrene–ethylene/butyl–ene-styrene (SEBS) triblock copolymers with the aim of improving the compatibility and in particular the toughness of the blends. The compatibilizers involved an unfunctionalized SEBS and two functionalized grades containing either maleic anhydride (SEBS-g-MAH) or glycidyl methacrylate (SEBS-g-GMA) grafted to the midblock. The effects of the compatibilizers were evaluated by studies on morphology and mechanical, thermal and rheological properties of the blends. The additon of 5 wt % of a SEBS copolymer was found to stabilize the blend morphology and to improve the impact strength. The effect was, however, far more pronounced with the functionalized copolymers. Particularly high toughness combined with rather high stiffness was achieved with SEBS-g-GMA for the PET-rich composition. Addition of the functionalized SEBS copolymers resulted in a finer dispersion of the minor phase and clearly improved interfacial adhesion. Shifts in the glass transition temperature of the PET phase and increase in the melt viscosity of the compatibilized blends indicated enhanced interactions between the discrete PET and PP phases induced by the functionalized compatibilizer, in particular SEBS-g-GMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:241–249, 1997     

Influence of microstructure and flexibility of maleated styrene-b-(ethylene-co-butylene)-b-styrene rubber on the mechanical properties of polyamide 12

The present investigation deals with the mechanical and morphological properties of binary polyamide 12/maleic anhydride-grafted styrene-b-(ethylene-co-butylene)-b-styrene rubber (PA12/SEBS-g-MA) blends at varying dispersed phase (SEBS-g-MA) concentrations. Tensile behavior, impact strength and crystallinity of these blend systems were evaluated. Influence of microstructure, dispersed phase particle size, and ligament thickness on the impact toughness of the blend was studied. DSC data indicated an increase in crystallinity of PA12 in the blends. Tensile modulus and strength decreased while impact strength and elongation-at-break increased with the elastomer concentration. The enhanced properties were supported by interphase adhesion between the grafted maleic groups of rubber with polar moiety of polyamide 12. Analysis of the tensile data employing simple theoretical models showed the variation of stress concentration effect with blend composition.     

Core/shell morphologies in recycled poly(ethylene terephthalate)/linear low-density polyethylene/poly(styrene-<Emphasis Type="Italic">b</Emphasis>-(ethylene-<Emphasis Type="Italic">co</Emphasis>-butylene)-<Emphasis Type="Italic">b</Emphasis>-styrene) ternary blends

Compatibilizer plays very important roles in preparing high performance polymer composites, not only for the ternary immiscible polymer blends, but also for the recycled and reused of waste plastics mixture. Generally, the compatibilizers can be used as the toughening agent in blending polymer materials. In the present work, the poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) or maleic anhydride-grafted poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS-g-MA) acts as the compatibilizer and toughening agent for the preparation of R-PET/LDPE/SEBS (70/20/10) ternary blends. It must be pointed that the ternary blends are costlessly and conveniently prepared from the recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) through a melt blending in a co-rotating twin-screw extruder and injection moulded. The morphologies of the ternary blends are characterized by scanning electron microscopy (SEM). It was found that the blends contains reactive or non-reactive compatibilizer, the morphology originates from the LLDPE particles encapsulated by both SEBS and SEBS-g-MA. So, it results to the reduced interfacial tension between of the R-PET and SEBS-g-MA, in which the grafted chains of PET-g-SEBS-g-MA formed through in situ reaction between R-PET and SEBS-g-MA phases. Therefore, core–shell particles with smaller diameter disperse uniformly in the blends. Moreover, the good compatibilization and corresponding morphologies induce in balanced mechanical and thermal properties. DSC analysis show the dispersed phase particles could act as nucleating agent in the R-PET matrix, which results the improvement of the crystallization temperature. And it was also observed the decreased nucleation activity in graft copolymers in the R-PET/LLDPE/SEBS-g-MA blends. Notched Charpy impact strength and elongation at break are improved by the addition of compatibilizer.     

Thermal and crystallisation behaviours of blends of polyamide 12 with styrene-ethylene/butylene-styrene rubbers

Polyamide 12 (PA12)/styrene-ethylene/butylene-styrene (SEBS) and PA12/maleic anhydride grafted SEBS (SEBS-g-MA) blends were prepared in a twin-screw extruder followed by injection moulding. Thermal and crystallisation behaviours of these blends were evaluated. Thermal properties and morphology of the blends were estimated using thermo gravimetric analysis (TGA) and scanning electron microscopy (SEM), respectively. The phase structure of the blends was interpreted by dynamic mechanical thermal analyser (DMTA). In terms of temperature at maximum rate of degradation (T_max) and integral procedural decomposition temperature (IPDT), it was found that PA12/SEBS-g-MA (PM) blends possessed greater thermal stability than PA12/SEBS (PS) blends. The kinetics of degradation process of PA12 and its blends were studied using Coats-Redfern (CR) method. It was found that there is no appreciable change in the thermal stability of PA12 in the presence of small amount of rubber phase. A good correlation was observed between the thermal properties and phase morphology of the blends. Melting and crystallisation behaviours of the blends were analysed by differential scanning calorimetry (DSC). These results showed that the melting and crystallisation behaviours of PA12 were not significantly affected by blending with rubbers. It was also observed that the functional group present in the rubber phase has little effect on the melting and crystallisation behaviours of PA12.     

Wide-angle X-ray diffraction investigation on crystallization behavior of PA6/PS/SEBS-g-MA blends

Blends of polystyrene/polyamide 6 (PS/PA6) compatibilized by styrene-ethylene/butylene-styrene (SEBS) elastomer grafted with maleic anhydride were prepared by melt blending. Wide-angle X-ray diffraction (WAXD) scans indicated a skin–core structure formed in the specimens during the injection-molding process. The results showed that the specimens tended to form the α-crystalline form in the core region, but the γ-crystalline form in the skin region. The influences of PS and SEBS-g-MA on the crystallization of PA6 were different in the core region and skin region. In the core region, PS made the PA6 tend to be in the γ-crystalline form, but the influence of PS was contrary in the skin region. SEBS-g-MA had both enhancement and toughening effects on the blends. The mechanical properties of the blends were determined by the combined action of the two aforementioned factors.     

Effect of transfer film on tribological behavior of polyamide 66‐based binary and ternary nanocomposites

BACKGROUND: In a polymer–metal sliding system, the formation and performance of the transfer film have important effects on the tribological behavior of the polymer. In order to reveal the wear mechanism of polyamide 66 (PA 66) and its composites consisting of styrene–(ethylene/butylene)–styrene triblock rubber grafted with maleic anhydride (SEBS‐g‐MA) particles and organoclay nano‐layers, the tribological behavior and transfer films of polyamide 66 and its composites were investigated under dry sliding. RESULTS: The incorporation of SEBS‐g‐MA rubber particles reduces the wear mass loss of PA 66, while the addition of organoclay nano‐layers increases the wear mass loss. The transfer films formed by neat PA 66 and PA 66/organoclay binary nanocomposite include a dark portion and bright portion. In the dark portion, the transfer film is thicker; in the bright portion, the steel ring surface is exposed. The transfer film formed by PA 66/SEBS‐g‐MA/organoclay ternary nanocomposite is thinner and more uniform than the transfer films formed by the other materials. CONCLUSION: When SEBS‐g‐MA rubber particles and organoclay nano‐layers are added simultaneously to PA 66, the wear resistance of PA 66 can be improved markedly. The main reason is that PA 66/SEBS‐g‐MA/organoclay ternary nanocomposite can form a thin and uniform transfer film on the steel ring surface. Copyright © 2008 Society of Chemical Industry     

A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rubber toughening of an amorphous polyamide by functionalized SEBS copolymers: morphology and Izod impact behavior

Rubber toughening of an amorphous polyamide (Zytel 330) using combinations of triblock copolymers of the type SEBS and a maleic anhydride functionalized version, SEBS-g-MA, was investigated and the results compared with those of nylon 6 and nylon 66. The effects of rubber content and the type of extruder on the morphology, Izod impact behavior and the ductile-brittle transition temperature were explored. The shape and sizes of the rubber particles in blends with this amorphous polyamide were found to be more similar to those in nylon 6 than in nylon 66 blends. The twin screw extruder produced smaller particles with a more narrow distribution of sizes than the single screw extruder. Higher rubber contents generally yielded tougher blends; there is a critical rubber particle size above which the ternary blends are brittle at 20 wt% total rubber. The ductile-to-brittle temperature was found to decrease with increased rubber content and decreased rubber particle size. In general, the trends for this amorphous polyamide are rather similar to those reported earlier for semi-crystalline nylon 6 and nylon 66.     

Morphology and mechanical properties of polyamide 12 blends with styrene/ethylene–butylene/styrene rubbers with and without maleation

Blends of polyamide 12 (PA12) with styrene/ethylene–butylene/styrene (SEBS) and maleic anhydride grafted SEBS (SEBS‐g‐MA) were prepared by twin‐screw extrusion and injection molding. The morphology, mechanical properties, and dynamic mechanical properties of the blends were studied. The morphology of the blends was evaluated from the etched surfaces of cryogenically fractured specimens with scanning electron microscopy. The morphological parameters showed that the PA12/SEBS‐g‐MA blends (PM series) exhibited a finer and more uniform rubber dispersion than the PA12/SEBS blends (PS series) because of the interfacial chemical reactions. SEBS functionalization via maleic anhydride grafting strongly affected the morphological parameters, such as the domain size, interfacial area per unit of volume, and critical interparticle distance, but the distribution of the rubber domains in the blends was less affected. Tensile and impact studies showed that the PS blends had worse mechanical properties than the PM blends. The tensile strength and elongation at break of the PM blends were considerably greater than those of the PS blends. The fracture toughness and energy values determined for notched Charpy specimens in high‐speed impact tests were markedly higher for the PM blends than for the PS blends. A similar observation was obtained from instrumented falling weight impact studies. Dynamic mechanical analysis confirmed the incompatibility of the blend components because the glass‐transition temperatures of PA12 and the rubber phase (SEBS and SEBS‐g‐MA) were not affected. © 2005 Wiley Periodicals, Inc. J Appl polym Sci 95: 1376–1387, 2005     

Toughening of nylon 6 with grafted rubber impact modifiers

Recent work has shown that nylon 6/acrylonitrile–butadiene–styrene (ABS) blends can be made tough by the addition of some polymer additives that are chemically reactive with nylon 6 and physically compatible with the styrene-acrylonitrile copolymer (SAN) phase of ABS. Imidized acrylic polymers (IA) represent a successful example of such additives that improve the dispersion of ABS in the nylon 6 matrix and render the blends tough. This article examines the possibility of toughening nylon 6 with ethylene/propylene/diene elastomer grafted with SAN copolymer (EPDM-g-SAN). This EPDM-g-SAN consists of 50% rubber and 50% SAN by weight. However, it was found that the same IA that works well to disperse ABS materials of similar rubber content is not as effective for EPDM-g-SAN, primarily because the EPDM forms the continuous phase, not SAN, and, thus, interfaces with nylon 6 during melt blending. Maleated elastomers like maleic anhydride grafted ethylene–propylene copolymer (EPR-g-MA) and styrene–(ethylene-co-butylene)–styrene triblock copolymer (SEBS-g-MA) were more effective for dispersing EPDM-g-SAN in the nylon 6 matrix than IA. Various mechanisms that improve the dispersion are discussed. © 1995 John Wiley & Sons, Inc.     

Compatibilisation of blends of poly(vinyl chloride) and poly(styrene-block-(ethylene-co-butadiene)-block–styrene) with maleic anhydride grafting

Abstract

The mechanical properties of blends of poly (vinyl chloride) (PVC) and poly (styrene-block-(ethylene-co-butadiene)-block–styrene) (SEBS) were investigated using maleic anhydride grafted SEBS (SEBS-g-MAH) as a compatibiliser. The results indicated that addition of a small amount of SEBS-g-MAH during melt blending significantly improved the mechanical properties of PVC/SEBS blends. The impact strength of the compatibilised PVC/SEBS blends was found to reach a maximum of 53·5±2·78 KJ m^?2 at room temperature and a maximum of 32·8±1·66 KJ m^?2 at ?20°C at an SEBS-g-MAH loading level of 6 phr. The two glass transition temperatures of the components in the blends converged to some degree upon addition of SEBS-g-MAH for compatibilisation. At room temperature the dynamic storage modulus of the compatibilised blends was higher than that of the blends without compatibilisation. The size of the dispersed phase domains in the blends was appreciably reduced on addition of SEBS-g-MAH during melt blending according to scanning electron microscopy. All the above observations revealed that SEBS-g-MAH enhanced the compatibility between PVC and SEBS in the PVC/SEBS blends.     

Ternary polymer composites: PA6,6/maleated SEBS/glass beads

Polyamide 6,6 (PA6,6)/maleated styrene–hydrogenated butadiene–styrene (SEBS) blends filled with up to 20% spherical glass beads (GBs) were prepared by extrusion and subsequent injection molding. Tensile and impact tests were used to examine the effect of GB additions on the mechanical behavior of PA6,6/SEBS–g–MA 80/20 blend. Tensile measurements showed that the GB additions improve the stiffness of the PA6,6/SEBS–g–MA 80/20 blend but had little effect on its tensile ductility. The impact test revealed that the impact strength of PA6,6/SEBS–g–MA 80/20 blend tends to decrease with increasing GB content. Therefore, the GB additions were beneficial to maintain a stiffness-to-toughness balance of the PA6,6/SEBS–g–MA 80/20 blend. Finally, the correlation between the experimental tensile stiffness and strength with various theoretical models is discussed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3231–3237, 2001