Plasticized poly(lactic acid) with low molecular weight poly(ethylene glycol): Mechanical,thermal, and morphology properties

Poly(lactic acid) PLA was plasticized with low molecular weight poly(ethylene glycol) PEG‐200 to improve the ductility of PLA, while maintaining the plasticizer content at maximum 10 wt%. Low molecular weight of PEG enables increased miscibility with PLA and more efficient reduction of glass transition temperature (T_g). This effect is enhanced not only by the low molecular weight but also by its higher content. The tensile properties demonstrated that the addition of PEG‐200 to PLA led to an increase of elongation at break (>7000%), but a decrease of both tensile strength and tensile modulus. The plasticization of the PLA with PEG‐200 effectively lowers T_g as well as cold‐crystallization temperature, increasing with plasticizer content. SEM micrographs reveal plastic deformation and few long threads of a deformed material are discernible on the fracture surface. The use of low molecular weight PEG‐200 reduces the intermolecular force and increases the mobility of the polymeric chains, thereby improving the flexibility and plastic deformation of PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4576–4580, 2013     

Stereocomplex‐induced gelation properties of polylactide/poly(ethylene glycol) diblock and triblock copolymers

The ring‐opening polymerization of L ‐ or D ‐lactide was realized in the presence of dihydroxyl or monomethoxy poly(ethylene glycol) (PEG) with a number‐average molecular weight of 2000. The resulting low‐molar‐mass poly(L ‐lactide) (PLLA)/PEG and poly(D ‐lactide) (PDLA)/PEG triblock and diblock copolymers were characterized with nuclear magnetic resonance (NMR), differential scanning calorimetry, size‐exclusion chromatography, and X‐ray diffractometric analysis. Bioresorbable hydrogels were successfully prepared from aqueous solutions containing both copolymers because of interactions and stereocomplexation between the PLLA and PDLA blocks. Gelation was evaluated with the tube inverting method and rheological measurements. A phase diagram was realized with gel–sol transitions as a function of concentration. The rheological properties of the hydrogels were investigated under various conditions through changes in the copolymer concentration, temperature, time, and frequency. It was concluded that the hydrogels constituted a dynamic and evolutive system because of the continuous formation/destruction of crosslinks and degradation. Further studies are underway to elucidate the degradation behavior and the potential of these substances as drug carriers or cell culture scaffolds. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Tributyl citrate as an effective plasticizer for biodegradable polymers: effect of plasticizer on free volume and transport and mechanical properties

The effectiveness of tributyl citrate (TbC) as a plasticizer for polylactide and polyhydroxybutyrate was analysed in order to improve the ductility of these polymers and make them good candidates for food packaging applications. Although the thermal and mechanical properties have been widely studied in the literature, the effect of the plasticizer on free volume and transport properties has not been deeply analysed. The free volume was characterized using positron annihilation lifetime spectroscopy observing its linear increase with TbC content. The permeability to water vapour, oxygen and carbon dioxide was determined and the obtained results were related to the changes in glass transition temperature, level of crystallinity of the samples and free volume. This work would allow a better understanding of the effect of the plasticizer on the barrier and mechanical properties of polymers allowing the development of competitive materials for packaging applications. © 2018 Society of Chemical Industry     

Plasticizing effect of poly(ethylene glycol)s with different molecular weights in poly(lactic acid)/starch blends

Binary and ternary blends composed of poly(lactic acid) (PLA), starch, and poly(ethylene glycols) (PEGs) with different molecular weights (weight‐average molecular weights = 300, 2000, 4000, 6000, and 10, 000 g/mol) were prepared, and the plasticizing effect and miscibility of PEGs in poly(lactic acid)/starch (PTPS) or PLA were intensively studied. The results indicate that the PEGs were effective plasticizers for the PTPS blends. The small‐molecule plasticizers of PEG300 (i.e., the M_w of PEG was 300g/mol) and glycerol presented better plasticizing effects, whereas its migration and limited miscibility resulted in significant decreases in the water resistance and elongation at break. PEG2000, with a moderate molecular weight, was partially miscible in sample PTPS3; this led to better performance in water resistance and mechanical properties. For higher molecular weight PEG, its plasticization for both starch and PLA was depressed, and visible phase separation also occurred, especially for PTPS6. It was also found that the presence of PEG significantly decreased the glass‐transition temperature and accelerated the crystallization of the PLA matrix, depending on the PEG molecular weight and concentration. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41808.     

Characterization and emulsifying properties of block copolymers prepared from lactic acid and poly(ethylene glycol)

Block copolymers were prepared by the direct polycondensation of an aqueous lactic acid solution on monomethoxy or dihydroxyl poly(ethylene glycol) (PEG) in the absence of a catalyst. The resulting poly(lactic acid) (PLA)–PEG diblock and PLA–PEG–PLA triblock copolymers were characterized by various analytical techniques, including matrix‐assisted laser desorption/ionization time of flight mass spectrometry (MALDI‐TOF MS), gel permeation chromatography, and ¹H‐NMR. The molecular structure between PLA–PEG and PLA–PEG–PLA could be distinguished after the calculation of the repeat unit masses and end‐group masses through the MALDI‐TOF MS spectra. Interestingly, both copolymers could serve as a hydrophilic emulsifier to stabilize the squalene/water interfaces and yield narrowly distributed oil‐in‐water nanoparticles. In contrast, the prepolymer PEG failed to stabilize the squalene/water interface under the same homogenization conditions. These features are of great interest for applications as bioactive agent delivery, especially for candidate vaccine antigens and lipophilic anticancer drugs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

ABA triblock copolymers from poly(p‐dioxanone) and poly(ethylene glycol)

Poly(p‐dioxanone)–poly(ethylene glycol)–poly(p‐dioxanone) ABA triblock copolymers (PEDO) were synthesized by ring‐opening polymerization from p‐dioxanone using poly(ethylene glycol) (PEG) with different molecular weights as macroinitiators in N₂ atmosphere. The copolymer was characterized by ¹H NMR spectroscope. The thermal behavior, crystallization, and thermal stability of these copolymers were investigated by differential scanning calorimetry and thermogravimetric measurements. The water absorption of these copolymers was also measured. The results indicated that the content and length of PEG chain have a greater effect on the properties of copolymers. This kind of biodegradable copolymer will find a potential application in biomedical materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1092–1097, 2006     

The effect of poly(ethylene glycol) as plasticizer in blends of poly(lactic acid) and poly(butylene succinate)

The effect of polyethylene glycol (PEG) on the mechanical and thermal properties of poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) blends was examined. Overall, it was found that PEG acted as an effective plasticizer for the PLA phase in these microphase‐separated blends, increasing the elongation at break in all blends and decreasing the T_g of the PLA phase. Significant effects on other properties were also observed. The tensile strength and Young's modulus both decreased with increasing PEG content in the blends. In contrast, the elongation at break increased with the addition of PEG, suggesting that PEG acted as a plasticizer in the polymer blends. Scanning electron microscope images showed that the fracture mode of PLA changed from brittle to ductile with the addition of PEG in the polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43044.     

Effect of water on the oxygen barrier properties of poly(ethylene terephthalate) and polylactide films

The aim of this work was to study the variations in the oxygen diffusion, solubility, and permeability coefficients of polylactide (PLA) films at different temperatures (5, 23, and 40°C) and water activities (0–0.9). The results were compared with the oxygen diffusion, solubility, and permeability coefficients obtained for poly(ethylene terephthalate) (PET) films under the same experimental conditions. The water sorption isotherm for PLA films was also determined. Diffusion coefficients were determined with the half‐sorption time method. Also, a consistency test for continuous‐flow permeability experimental data was run to obtain the diffusion coefficient with the lowest experimental error and to confirm that oxygen underwent Fickian diffusion in the PLA films. The permeability coefficients were obtained from steady‐state permeability experiments. The results indicated that the PLA films absorbed very low amounts of water, and no significant variation of the absorbed water with the temperature was found. The oxygen permeability coefficients obtained for PLA films (2–12 × 10^?18 kg m/m² s Pa) were higher than those obtained for PET films (1–6 × 10^?19 kg m/m² s Pa) at different temperatures and water activities. Moreover, the permeability coefficients for PLA and PET films did not change significantly with changes in the water activity at temperatures lower than 23°C. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1790–1803, 2004     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

Catalyst free synthesis of poly(l‐lactic acid)–poly(propylene glycol) multiblock copolymers and their properties

A simple, green, and economical method for the synthesis of poly(l ‐lactic acid)–poly(propylene glycol) (PLLA–PPG) copolymers is put forward and a series of multiblock PLLA–PPG are synthesized with 1,6‐hexamethylene diisocyanate as chain extender of the melt polymerization. The effect of PPG content on the properties of PLLA–PPG copolymers is also investigated. The elongation at break of the resulting copolymer film with only 5% weight content PPG is 280%, and the tensile strength is 20 MPa. Dynamic mechanical analysis results demonstrated the existence of the shape memory effect for all the copolymers films and the shape recovery ratio of 101% is achieved for PLLA–PPG copolymer film with 5% weight PPG. The process for the synthesis of PLLA–PPG copolymers in the total absence of potentially toxic solvents and catalysts is analyzed, and the films of PLLA–PPG exhibit toughness and shape memory effect. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45299.     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Synthesis and properties of ABA-type triblock copolymers of poly(glycolide-co-caprolactone) (A) and poly(ethylene glycol) (B)

Poly(glycolide-co-caprolactone) (A)-poly(ethylene glycol) (B) ABA-type triblock copolymers (PGCE) were synthesized by bulk ring opening polymerization, using the hydroxyl endgroups of poly(ethylene glycol) (PEG) as initiator and stannous octoate as catalyst. The resulting copolymers were characterized by various analytical techniques. Gel permeation chromatographic analysis indicated that the polymerization product was free of residual monomers, PEG and oligomers. ¹H NMR and differential scanning calorimeter results demonstrated that the copolymers had a structure of poly(glycolide-co-caprolactone) (PGC) chains chemically attached to PEG segments. All the PGCE copolymers showed improved hydrophilicity in comparison with the corresponding PGC copolymers with the same molar ratio of glycolidyl and caproyl units. The microspheres of PGCE copolymer exhibited rough surfaces quite different from the smooth surface of PGC microspheres. This phenomenon was attentively ascribed to the highly swollen ability of PGCE copolymers and the freeze-drying process in the microspheres fabrication.     

聚乙二醇增塑聚乳酸的非等温结晶动力学研究

采用DSC方法对聚乙二醇(PEG)增塑聚乳酸的非等温结晶动力学进行了研究。结果表明,PEG的加入明显提高了聚乳酸的结晶速度。对所得数据分别用Ozawa方程和莫志深方法进行了处理,发现在给定温度范围里非等温结晶时,PLA/PEG主要是以均相成核的三维生长方式结晶;PLA的结晶速度随着PEG分子质量的增加而升高。     

Synthesis and characterization of amphiphilic polyisobutylene/poly(ethylene glycol) di- and triblock copolymers

Summary Di- and triblock copolymers of polyisobutylene PIB and poly(ethylene glycol) PEG have been prepared and characterized. The syntheses involved the capping with tolylene 2,4-diisocyanate TDI various molecular weight -phenyl--(p-phenol) polyisobutylenes C₆H₅-PIB-C₆H₄OH and ,-di-(p-phenol)polyisobutylenes HOC₆H₄-PIB-C₆H₄OH, or commercially available mono- and di-hydroxyl-terminated PEGs. In this manner a series of PIB-b-PEG diblock copolymers, and PEG-b-PIB-b-PEG and PIB-b-PEG-b-PIB triblock copolymers have been obtained. The complete removal of the prepolymers from these amphiphilic sequential copolymers by conventional solvent extraction techniques could not be achieved because of the very high emulsifying action of the latters. In contrast, satisfactory separation was obtained by column chromatography using mixed (polar/nonpolar) eluents. The blocking efficiencies and composition of the block copolymers have been determined.Part XL V of the Series on New Telechelic Polymers and Sequential Copolymers by Polyfunctional Initiator-Transfer Agents (Inifers).     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 1. Poly(lactide) with low stereoregularity

Poly(lactide) (PLA) is rapidly gaining interest as a biodegradable thermoplastic for general usage in degradable disposables. To improve mechanical properties, a PLA with low stereoregularity was blended with polyethylene glycol (PEG). Blends with up to 30 wt% PEG were miscible at ambient temperature. Blending with PEG significantly decreased the T_g, decreased the modulus and increased the fracture strain of PLA. However, the PLA/PEG 70/30 blend became increasingly rigid over time at ambient conditions. The mechanism of aging primarily under ambient conditions of temperature and humidity was studied. Changes in mechanical properties, thermal transitions and solid state morphology were examined over time. Aging was caused by slow crystallization of PEG. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g. As T_g approached the aging temperature, reduced molecular diffusivity slowed the crystallization rate dramatically. Aging essentially ceased when T_g of the amorphous phase reached the aging temperature. The increase in matrix T_g and the reinforcing effect of the crystals produced a change in mechanical properties from elastomer-like to thermoplastic-like.     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 2. Poly(lactide) with high stereoregularity

Blending poly(ethylene glycol) (PEG) with poly(lactide) (PLA) decreases the T_g and improves the mechanical properties. The blends have lower modulus and increased fracture strain compared to PLA. However, the blends become increasingly rigid over time at ambient conditions. Previously, it was demonstrated that a PLA of lower stereoregularity was miscible with up to 30 wt% PEG. Aging was due to slow crystallization of PEG from the homogeneous amorphous blend. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g until aging essentially ceased when T_g of the amorphous phase reached the aging temperature. In the present study, this aging mechanism was tested with a crystallizable PLA of higher stereoregularity. Changes in thermal transitions, solid state structure, and mechanical properties were examined over time. Blends with up to 20 wt% PEG were miscible. Blends with 30 wt% PEG could be quenched from the melt to the homogenous amorphous glass. However, this composition phase separated at ambient temperature with little or no crystallization. Changes in mechanical properties during phase separation reflected increasing rigidity of the continuous PLA-rich phase as it became richer in PLA. Construction of a phase diagram for blends of higher stereoregular PLA with PEG was attempted.     

Nonisothermal crystallization behaviors of biodegradable double crystalline poly(butylene succinate)‐poly(ethylene glycol) multiblock copolymers

Nonisothermal crystallization behaviors of both poly(butylene succinate) (PBS) and poly(ethylene glycol) (PEG) segments within PBS‐PEG (PBSEG) multiblock copolymers were investigated by differential scanning calorimetry (DSC). The nonisothermal crystallization kinetics of both PBS and PEG segments were analyzed by Avrami, Ozawa, and Mo methods. The results showed that both of Avrami and Mo methods were successful to describe the nonisothermal crystallization kinetics of PBS and PEG segments. The results of crystallization kinetics indicated that the crystallization rate of PBS segment decreased with PBS segment content and/or L_PBS, while that of PEG segment decreased with M_n,PEG or F_PEG. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40940.     

Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

Fully biobased biodegradable poly(l‐lactide)‐b‐poly(ethylene brassylate)‐b‐poly(l‐lactide) triblock copolymers: synthesis and investigation of relationship between crystallization morphology and thermal properties

Well‐defined poly(l ‐lactide‐b‐ethylene brassylate‐b‐l ‐lactide) (PLLA‐b‐PEB‐b‐PLLA) triblock copolymer was synthesized by using double hydroxyl‐terminated PEBs with different molecular weights. Gel permeation chromatography and NMR characterization were employed to confirm the structure and composition of the triblock copolymers. DSC, wide‐angle X‐ray diffraction, TGA and polarized optical microscopy were also employed to demonstrate the relationship between the composition and properties. According to the DSC curves, the cold crystallization peak vanished gradually with decrease of the PLLA block, illustrating that the relatively smaller content of PLLA may lead to the formation of a deficient PLLA type crystal, leading to a decrease of melting enthalpy and melting temperature. Multi‐step thermal decompositions were determined by TGA, and the PEB unit exhibited much better thermal stability than the PLLA unit. Polarized optical microscopy images of all the triblock samples showed that spherulites which develop radially and with an extinction pattern in the form of a Maltese cross exhibit no ring bond. The growth rate of the spherulites of all triblock samples was investigated. The crystallization capacity of PLLA improved with incorporation of PLLA, which accords with the DSC and wide‐angle X‐ray diffraction results. © 2019 Society of Chemical Industry     

Synthesis and properties of novel biodegradable triblock copolymers of poly(5-methyl-5-methoxycarbonyl-1,3-dioxan-2-one) and poly(ethylene glycol)

Novel biodegradable triblock copolymers of poly(5-methyl-5-methoxycarbonyl-1,3-dioxan-2-one) (PMMTC) with poly(ethylene glycol) (PEG), PMMTC-b-PEG-b-PMMTC, were synthesized by the ring-opening polymerization of MMTC in bulk, using the dihydroxyl PEG as initiator and Sn(Oct)₂ as catalyst. The triblock copolymers with different compositions were characterized by IR and ¹H NMR, their molecular weight was measured by gel permeation chromatography (GPC). The results showed that the molecular weight of triblock copolymers increased either with the increase of the molar ratio of MMTC in feed while the PEG chain length kept constant, or by lengthening the backbone chain of PEG block with the same ratio of MMTC in feed. The hydrophilicity of copolymers was greatly improved by incorporation of PEG block into polycarbonate. The in vitro hydrolytic/enzymatic degradation and controlled drug release properties of the triblock copolymers were also investigated.