Gamma radiation aging of EVA/EPDM blends: Effect of vinyl acetate (VA) content and radiation dose on the alteration in mechanical,thermal, and morphological behavior

A series of ethylene vinyl acetate (EVA)/ethylene‐propylene diene elastomer (EPDM) blends (50/50 ratio) with four types of EVAs were prepared using brabender type batch mixer followed by compression molding. All compression‐molded samples were exposed to gamma radiation at 500, 1000, and 1500 kGy doses and were subjected to mechanical, compression set, thermal and morphological test. The % retention in tensile strength, elongation, and hardness were found higher for higher vinyl acetate (VA) containing radiation aged EVA/EPDM blends. The compression set value was decreased with increase of VA content. The thermal degradation kinetics of high VA containing irradiated blend (EVA40/EPDM) (EVA40 is 40%VA containing EVA) was found slower than those of lower VA containing blend (EVA18/EPDM). The surface morphology for EVA18/EPDM sample was transformed into more irregular one with more cracks and fragmented segments by aging at 1500 kGy dose while surface for EVA40/EPDM sample was found comparatively smooth, fine, and continuous with very few cracks and fragmented parts at similar dose. Thus, from the measured properties and morphology, it was revealed that the degree of degradation of blends kept on decreasing with increase in VA content. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46216.     

Toughening effects of ethylene–vinyl acetate copolymers with different vinyl acetate content and viscosity on nylon 1010 blends

Nylon 1010 blends with ethylene–vinyl acetate copolymer (EVA) and maleated ethylene–vinyl acetate (EVA‐g‐MAH) were prepared through melt blending. The vinyl acetate (VA) content and viscosity of EVA significantly affected the notched impact strength of nylon/EVA/EVA‐g‐MAH (80/15/5) blends. The nylon/EVA/EVA‐g‐MAH blends with high notched impact strength (over 60 kJ/m²) were obtained when the VA content in EVA ranged from 28 to 60 wt%. The effect of VA content on the notched impact strength of blends was related to the glass transition temperature for EVA with high VA content and crystallinity for EVA with low VA content. For nylon blends with EVA with the same VA content, low viscosity of EVA led to high notched impact strength. Fracture morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends showed that blends with ductile fracture behavior usually had large matrix plastic deformation, which was the main energy dissipation mechanism. A relationship between the notched impact strength and the morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends was well correlated by the interparticle distance model. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Hansen solubility parameter: from polyethylene and poly(vinyl acetate) homopolymers to ethylene–vinyl acetate copolymers

The Hansen solubility parameters (HSPs ) of two ethylene–vinyl acetate (EVA ) copolymers (with 18 and 33 wt% of vinyl acetate) and their corresponding homopolymers (polyethylene, PE , and poly(vinyl acetate), PVAc ) have been studied at various temperatures, employing the previously obtained Flory–Huggins parameters. From these latter values, a procedure based on the Hansen solubility spheres theory was employed to determine the HSPs , as well as the radius of interaction. The procedure was validated with literature data, with deviations of around 3%. The HSP values (dispersion, polar and association terms, respectively, all in MPa^{1 /2}) at 333.15 K are 14.84, ?3.88 and 1.78 for PE , 17.65, ?1.24 and 2.76 for EVA410 (with 18 wt% of vinyl acetate), 17.52, 0.15 and 3.61 for EVA460 (with 33 wt% of vinyl acetate) and 19.45, 10.59 and 5.76 for PVAc . The main characteristic of the obtained HSP values is that the high polar term of PVAc tends to increase the solubility character of the pure PE , and thus the EVA copolymers, allowing them to solubilize dispersion and polar compounds. Finally, it was also demonstrated that it is possible to predict the HSPs of EVA copolymers using the vinyl acetate content and the HSPs of pure PE and PVAc as input data. © 2017 Society of Chemical Industry     

Corona discharge treatment of EVAs with different vinyl acetate contents

Four ethylene vinyl acetate (EVA) co-polymers with different vinyl acetate (VA) contents (9–20 wt%) were treated with corona discharge to improve their adhesion to polychloroprene (PCP) adhesive. The thermal properties of the EVAs decreased as their VA content increased, caused by a decrease in crystallinity. The elastic and viscous moduli of the EVAs decreased and the temperature and modulus at the cross-over between these moduli decreased with increasing VA content. Contact-angle measurements (water), infrared spectroscopy (ATR-IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were used to analyse the surface modifications produced in the corona-discharge-treated EVAs. The corona discharge treatment produced improved wettability and created roughness and oxygen moieties on the EVA surfaces. The higher the VA content and the higher the corona energy, the more significant modifications were produced on the EVA surface. The VA content also affected the T-peel strength values of treated EVA/polychloroprene + isocyanate adhesive joints, as the values increased with increasing VA content. Mixed failure modes (interfacial + cohesive failure in the EVA) were obtained in the adhesive joints produced with corona discharge treated EVAs containing more than 9 wt% VA. The accelerated ageing of the joints did not affect the T-peel strength values, but the locus of failure in most cases became fully cohesive in the EVA, likely due to the higher extent of curing of the adhesive.     

Use of pyrolyzed oil shale as filler in poly(ethylene‐co‐vinyl acetate) with different vinyl acetate contents

Pyrolyzed oil shale (POS) obtained from the pyrolysis of bituminous rock was used as filler in poly(ethylene‐co‐vinyl acetate) (EVA). The effects of the VA content of EVA and the particle size of POS on the mechanical properties were investigated. The composites were prepared in a rotor mixer at 180°C with a concentration of POS of up to 30 wt %. The stress–strain plots of the compression‐molded composites are similar to the EVA (18% VA content) behavior for low concentrations (1–5 wt %) of POS with a particle size lower than 270 mesh. It was observed that decreasing the POS particle size and increasing the VA content of EVA produced better compatibility between the polymer and filler. The mechanical properties, differential scanning calorimetry, and dynamic mechanical analysis also demonstrated the compatibility between EVA and POS under the increase of the VA content in the EVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1544–1555, 2002; DOI 10.1002/app.10494     

Ethylene vinyl acetate and ethylene vinyl alcohol copolymer for thermal spray coating application

Ethylene vinyl acetate (EVA) copolymer with varying vinyl acetate (VAc) content, viz. 18%, 28% and 40% has been hydrolyzed using alcoholic NaOH solution. Fourier Transform Infrared Spectroscopy (FTIR) analyses of hydrolyzed polymer showed the presence of both OH group and acetate group indicating that the EVA has been partially hydrolyzed. Differential Scanning Calorimeter (DSC) and Thermo Gravimetric Analyzer (TGA) of EVA and hydrolyzed EVA showed large difference in melting and decomposition temperature, respectively. Hydrolyzed EVA showed higher tensile strength and elongation at break compared to corresponding EVA. Blends of different grades of EVA and ethylene vinyl alcohol (EVAl) with low density polyethylene (LDPE) were applied on grit blasted mild steel surface by flame spray technique. FTIR analysis of blends before and after coating showed no degradation during flame spray. Measurement of adhesion strength of these coating showed that adhesion strength increased on hydrolysis of EVA.     

Effect of vinyl acetate content on the mechanical and thermal properties of ethylene vinyl acetate/MgAl layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA)/Mg‐Al layered double hydroxide (LDH) nanocomposites using EVA of different vinyl acetate contents (EVA‐18 and EVA‐45) have been prepared by solution blending method. X‐ray diffraction and transmission electron microscopic studies of nanocomposites clearly indicate the formation of exfoliated/intercalated structure for EVA‐18 and completely delaminated structure for EVA‐45. Though EVA‐18 nanocomposites do not show significant improvement in mechanical properties, EVA‐45 nanocomposites with 5 wt % DS‐LDH content results in tensile strength and elongation at break to be 25% and 7.5% higher compared to neat EVA‐45. The data from thermogravimetric analysis show that the nanocomposites of EVA‐18 and EVA‐45 have ≈10°C higher thermal decomposition temperature compared to neat EVA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Investigation of the photodegradation behaviors of an ethylene/vinyl acetate copolymer solar cell encapsulant and effects of antioxidants on the photostability of the material

This study concerns the photodegradation and stabilization of a solar cell encapsulating material made from ethylene/vinyl acetate copolymer (EVA). EVA was compounded with various additives in a twin‐screw extruder. After that, the extruded film was cured in a hydraulic compression mold before being exposed to ultraviolet (UV) radiation at an ambient temperature for 800 h. The thermal stability of the material was also studied through the aging of the sample at 90°C for 2000 h. The tensile strength of the unstabilized EVA decreased only slightly after the thermal aging. On the other hand, the strength of the material decreased noticeably after the UV irradiation. Fourier transform infrared spectra of various EVA films revealed that there was no deacetylation occurring after the UV irradiation. However, results from the swelling test and swollen‐state NMR suggested that the polymer degraded via a chain‐scission mechanism. After compounding with some antioxidants, most of the EVA films scarcely degraded after the UV irradiation, with the exception of the EVA compounded with a combination of the aromatic phosphate compound (0.1 phr) and hindered amine light stabilizer (0.1 phr). The results are discussed in light of an antagonism effect that occurred because of the aforementioned combination. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Improved adhesion of EVAs with different vinyl acetate contents treated with sulphuric acid

Four ethylene vinyl acetate copolymers (EVAs) containing 9, 12, 18 and 20 wt% vinyl acetate (VA) were treated with concentrated sulphuric acid to improve their adhesion to polychloroprene (PCP) adhesive. The tensile strength and Young's modulus of EVAs decreased as the VA content increased, due to the reduction in crystallinity of the polyethylene blocks in the copolymer. The modifications produced in the EVAs by treatment with sulphuric acid were followed using contact angle measurements (water, 25 °C), ATR-IR spectroscopy and scanning electron microscopy (SEM). Adhesive-bond strength was obtained by T-peel tests on treated EVA/polychloroprene adhesive joints. The vinyl acetate content in the EVA affected the extent, but not the nature, of the surface modification produced by treatment with sulphuric acid. The treatment produced both sulfonation and oxidation on the EVA surfaces. The higher the vinyl acetate content in the EVA, the more significant the modifications produced. Increased T-peel strengths of EVA/polychloroprene adhesive + 5 wt% polyisocyanate joints were obtained and a mixed failure (adhesion failure + cohesive failure in the adhesive) was produced. It was found that, to be effective, the treatment of EVAs must be carried out with 96 wt% sulphuric acid.     

Rheological behavior of ethylene–vinyl acetate copolymer and fabrication of micropyramid arrays by roll‐to‐roll hot embossing on its thin films

Films of ethylene–vinyl acetate (EVA) copolymer with different vinyl acetate (VA) contents were adopted as flexible substrates for fabrication of micropyramid arrays by roll‐to‐roll (R2R) hot embossing at roller temperatures 40–80 °C. An empirical relationship between rheological behavior of EVA in rubbery state and demolding performance of the films was explored. Dependence of average forming height of micropyramid arrays on VA content and roller temperatures was investigated. Our study showed that both viscosity and relaxation behavior of EVA can be related to the ultimate forming height of micropyramids. The relationships can provide references for experimental research and industrial manufacture on R2R hot embossing. Retroreflection of micropyramid arrays was observed and transmittances of the two sides of embossed films were studied. Transmittances of the VA28 film embossed at 60 °C were 97.9% (the embossed side) and 41.8% (the smooth side), which showed potential applications in reflective film and antireflective film fields. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45228.     

Melt grafting of poly(ethylene‐vinyl acetate) copolymer with maleic anhydride

Poly(ethylene‐vinyl acetate) (EVA) copolymer was melt grafted with maleic anhydride (MAH) in a twin screw extruder in the presence of peroxide. It is confirmed that MAH has been melt grafted on the backbone of EVA by FTIR using the method of hydrolysis. The NMR analysis suggests that the grafting reaction occurs on the tertiary carbon of main chain of EVA other than the methyl moiety of vinyl acetate (VA) group. The incorporation of VA groups onto the matrix shows a competitive effect on the grafting. The existence of VA groups promotes the extent of MAH graft onto EVA; nevertheless, it also weakens the crystallizability of main chain. When the content of peroxide initiator is 0.1 wt % based on the polymer matrix, the grafting degree increases with increasing the concentration of monomer. When the peroxide content is higher than 0.1 wt %, side reactions such as crosslinking or disproportionation will be introduced into this system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 841–846, 2006     

Kinetic features of the nonisothermal oxidative degradation of ethylene vinyl acetate copolymers

Thermogravimetric analysis was used for a comparative investigation of the thermooxidative decomposition of ethylene vinyl acetate (EVA) copolymers with different vinyl acetate (VA) group contents. There were two stages of mass loss in this process. It was revealed that the apparent activation energies were correlated with the content of VA groups in the EVA copolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1958–1961, 2004     

Ethylene vinyl acetate/Mg‐Al LDH nanocomposites by solution blending

Partially exfoliated ethylene vinyl acetate (EVA‐40, 40% vinyl acetate content)/layered double hydroxide (LDH) nanocomposites using organically modified layered double hydroxide (DS‐LDH) have been synthesized by solution intercalation method. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) studies of nanocomposites shows the formation of exfoliated LDH nanolayers in EVA‐40 matrix at lower DS‐LDH contents and partially intercalated/exfoliated EVA‐40/MgAl LDH nanocomposites at higher DS‐LDH contents. These EVA‐40/MgAl LDH nanocomposites demonstrate a significant improvement in tensile strength and elongation at break for 3 wt% of DS‐LDH filler loading compare to neat EVA‐40 matrix. Thermogravimetric analysis also shows that the thermal stability of the nanocomposites increases with DS‐LDH content in EVA‐40. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

A study of nano‐mechanical and macro‐mechanical properties of ethylene vinyl acetate

Nano‐ and macro‐mechanical properties of ethylene vinyl acetate (EVA) with various amounts of vinyl acetate (VA) have been investigated. Nano‐mechanical properties (modulus and hardness) were obtained using nano‐indentation measurements while macro‐mechanical properties were determined using tensile test measurements. A decrease in Young's modulus and hardness was observed with increasing VA content for both nano‐ and macro‐mechanical measurements. An increase in Young's modulus and hardness was observed as a function of the draw ratio keeping the VA content constant. The difference between macro‐ and nano‐mechanical properties as a function of VA content and draw ratio is explained in terms of crystallinity and chain orientation. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Preparation and characterization of ethylene‐vinyl acetate nanocomposites: enhanced flame retardant

Ethylene‐vinyl acetate (EVA) nanocomposites with enhanced flame retardance were prepared by the sol–gel process in the melt. Two EVAs with different vinyl acetate (VA) contents and aluminium isopropoxide were used as organic and inorganic phases. The nanocomposites were prepared in a batch mixer under constant processing conditions and were analysed by several characterization techniques. Aluminium isopropoxide presented low activation energy, which allows the synthesis of the nanoparticles without a post step treatment. The reaction mechanism is proposed. Nanocomposites with smaller and well dispersed metal nanoparticles were produced with an EVA with higher VA content. EVA nanocomposites achieve the requirements for 94 V‐0 classification. © 2013 Society of Chemical Industry     

Real-time analysis of ethylene vinyl acetate random copolymers using near infrared spectroscopy during extrusion

Poly(ethylene vinyl acetate) (EVA) is a very common polymer used in hot melt adhesives. The rheological and thermal-mechanical properties of these adhesives are strongly related to the content of vinyl acetate (VA) incorporated into this random copolymer during polymerization. Results of in-line monitoring of VA content in flowing molten EVA polymers, using fiberoptic near infrared spectroscopy, shall be discussed in detail. In-line monitoring is not only desired for its numerous advantages (such as high quality products, lower waste, lower developmental cycle time, and lower costs) but also because it eliminates the sample handling concerns associated with molten polymers.     

Barrier properties of poly(ethylene‐co‐vinyl acetate)/cellulose composite membranes

Poly(ethylene‐co‐vinyl acetate) (EVA)/cellulose composite membranes were prepared and their vapor permeation characteristics were studied. Two types of EVA [having vinyl acetate contents of 18% (EVA18) and of 40% (EVA40), respectively] were used for the composite fabrication. Cellulose, isolated from banana waste fibers, was used as the filler. It was observed that the EVA40 composites were more permeating than were the EVA18 composites. This observation is explained on the basis of more amorphous nature of EVA40 as compared to EVA18. The extent of vapor permeation decreased with increase in the cellulose content in the composites. The presence of voids in the polymer membranes that were designed to possess controlled behavior for the permeation was confirmed using scanning electron microscopic images to complement the observations made during the permeation studies. The influence of molecular weight, molar size, and polarity of the penetrants, on the permeation process, was also considered. The permeability of the membrane samples was calculated and the values obtained were compared with the theoretical values provided by using the modified Neilson permeability equation. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Rheological and mechanical performance of ethyl‐vinyl acetate/poly(vinyl chloride) formulations

A range of powdered ethyl‐vinyl acetate (EVA) copolymers and poly(vinyl chloride) (PVC) formulations were compounded at PVC:EVA ratios of 100:0, 60:40, 50:50, 40:60, and 0:100. Two grades of EVA with 20% and 27% of vinyl acetate (VAc) (EVA I and EVA II) and two grades of PVC with K values of 56 and 71 (PVC I and PVC II) were used in the investigation. Mechanical analysis was performed on injection molded samples of these blends, and the results showed that the tensile and flexural moduli decreased significantly with increasing EVA concentration. Rheological analysis was performed by using dual capillary rheometry, and the results showed only slight changes in shear viscosity with increasing EVA content, even at lower shear rates. Dynamic mechanical thermal analysis showed partial miscib lity of the PVC and EVA over the range of concentrations studied.     

Effect of electron beam irradiation and vinyl acetate content on the physicochemical properties of LDPE/EVA blends

The radiation‐induced crosslinking, compatibility, and surface modification of low density polyethylene/ethylene vinyl acetate blends (LDPE/EVA) were investigated. The structural and physical properties were characterized in terms of gel content, hot set, mechanical properties, contact angle, and surface free energy. The highest crosslink density was obtained at 20 wt % of EVA. Gel content of LDPE/EVA blends was increased with increasing irradiation dose, vinyl acetate (VA), and EVA contents. The hot set results are consistent with the gel content data. Mechanical testing showed that the tensile strength of samples increased with increasing irradiation dose up to 180 kGy, whereas the elongation at break was decreased with increasing irradiation dose. Contact angle measurements showed that the surface hydrophillicity of LDPE blend was increased with increasing irradiation dose and contents of both VA and EVA. The surface free energy was greatly dependent on irradiation dose and content of both VA and EVA. The total surface free energies of different LDPE formulations were in the range 17.25–32.51 mN/m, in which the polar (^pσ) and disperse (^dσ_s) values were within the range 16.52–26.6 and 0.9–5.91 mN/m, respectively. In conclusion, electron beam irradiation and blending LDPE with EVA improved the wettability or adhesion properties of LDPE/EVA blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Influence of the molecular weight of ethylene vinyl acetate copolymers on the flow and mechanical properties of uncompatibilized polystyrene/ethylene–vinyl acetate copolymer blends

Rubber‐toughened polystyrene (PS) has been extensively studied and is a well‐established material. However, the use of thermoplastic elastomers to toughen PS is new and not well understood. In this study, three types of ethylene vinyl acetate (EVA) copolymers with the same vinyl acetate (VA) content (27.2–28.8 wt %) but with different melt flow indexes (MFI; g (10 min)⁻¹) of 365–440 (Elvax 210), 38.0–48.0 (Elvax 240) and 2.6–3.4 (Elvax 265) were used as impact modifiers for PS. The uncompatibilized blend systems at different compositions were prepared using a twin‐screw extruder and injection moulding to produce the required test pieces. The viscosity of the dispersed phase (EVA) has a significant effect on the mechanical properties of the blends. Rheological studies show that uncompatibilized PS/EVA265 blends exhibit some degree of compatibility when the amount of EVA265 added is below 30 wt %. These results indicate that EVA265 with the lowest melt flow index or highest molecular weight is the most effective impact modifier for PS. The mechanism for such behaviour is still unclear. © 2001 Society of Chemical Industry