A 4.8–6.8 GHz low phase noise LC VCO in 0.13‐µm CMOS technology

This letter presents a novel LC voltage controlled oscillator (VCO) supporting the high‐speed serial transmission standard of RapidIO in 0.13‐µm complementary metal‐oxide semiconductor technology. The low phase noise is achieved through several techniques including current source switching, parallel coupled negative transconductance cell, and varactor bias combination scheme. Measured results of proposed circuit show a low phase noise of ?120 dBc/Hz at 1 MHz offset from 6.25 GHz carrier and tuning range of 4.8 ~ 6.8 GHz (34.48%) while consuming 7.4 mW under the supply voltage of 1.2 V. Copyright © 2015 John Wiley & Sons, Ltd.     

A linear,ultra wideband,low‐power, 2.1–5 GHz,VCO

A linear, Ultra Wideband, low‐power VCO, suitable for UWB‐FM applications is proposed, forming the main part of a UWB‐FM transmitter. The VCO is designed in TSMC 90thinspacenm digital CMOS process and includes a Source‐Coupled Multivibrator, used as current‐controlled oscillator (CCO) which generates output frequencies between 2.1 and 5 GHz and a voltage‐to‐current (V‐to‐I) converter which translates the VCO input voltage modulation signal to current. Two single‐ended inverter buffers are employed to drive either a differential or a single‐ended UWB antenna. The presented VCO is designed for 1 V power supply and exhibits a linear tuning range of 2.1–5 GHz, a differential output power of ?7.83 dBm±0.78 dB and low power consumption of 8.26 mW, including the output buffers, at the maximum oscillation frequency. It is optimized for a very high ratio of tuning range (81.69%) over power consumption equal to 9.95 dB. The desired frequency band of 3.1–5 GHz for UWB‐FM applications is covered for the entire industrial temperature range (?40 to 125^°C). Copyright © 2010 John Wiley & Sons, Ltd.     

Wide‐band divide‐by‐2 injection‐locked frequency divider using MOSFET mixers DC‐biased in subthreshold region

A novel wide locking range divide‐by‐2 injection‐locked frequency divider (ILFD) is proposed in the paper and was implemented in the TSMC 0.18‐µm 1P6M CMOS process. The divide‐by‐2 ILFD is based on a cross‐coupled voltage‐controlled oscillator (VCO) with an LC resonator and injection MOSFETs with source voltage coupled from ILFD output, and the injection MOSFET mixer is biased in subthreshold region. At the drain–source bias of 0.9 V, and at the incident power of 0 dBm the locking range of the divide‐by‐2 ILFD is 6.4 GHz; from the incident frequency 3.7 GHz to 10.1 GHz, the percentage is 92.75%. The core power consumption is 16.56 mW. The die area is 0.839 × 0.566 mm². Copyright © 2015 John Wiley & Sons, Ltd.     

Fully integrated 2.45‐GHz OOK receiver for wireless sensor networks

This paper introduces an optimized receiver architecture using the current‐reuse technique to improve receiver sensitivity while minimizing power consumption. An ISM band wireless receiver with OOK modulation was implemented in the TSMC 0.18‐µm CMOS process. The receiver contains an RF front end, an LC‐tank based LO VCO, an IF amplifier and an OOK demodulator. In addition, the IF amplifier features a self‐mixing elimination mechanism which allows the BER to upgrade more than one order of magnitude. Measurement results show a sensitivity of ?63 dBm given a BER of 10^?3. Using the gain‐improving method, the sensitivity is improved by 4 dB (100‐kbps data rate). Including the bias circuit, overall power consumption is less than 383 μW under a 1.2‐V supply, providing an alternate solution for wireless radio applications. Copyright © 2016 John Wiley & Sons, Ltd.     

A series‐coupled LC quadrature oscillator using phase/amplitude calibration

In this paper, an analytic approach for the estimation of the phase and amplitude error in series coupled LC quadrature oscillator (SC‐QO) is proposed. The analysis results show that imbalances in source voltage of coupling transistor because of mismatches between LC tanks are the main source of the phase and amplitude error in this oscillator. For compensation of the phase and amplitude error, a phase and amplitude‐tunable series coupled quadrature oscillator is designed in this paper. A phase shift generation circuit, designed using an added coupling transistor, can control the coupling transistor source voltage. The phase and amplitude error can simply be controlled and removed by tuning the phase shifter, while this correction does not have undesirable impact on phase noise. In fact, the proposed SC‐QO generates a phase shift in the output current, which reduces the resonator phase shift (RPS) and improves phase noise. The phase and amplitude tunable SC‐QO is able to correct the phase error up to ±12°, while amplitude imbalances are reduced as well. To evaluate the proposed analysis, a 4.5‐GHz CMOS SC‐QO is simulated using the practical 0.18‐μm TSMC CMOS technology with a current consumption of 2 mA at 1.8‐V supply voltage. Copyright © 2016 John Wiley & Sons, Ltd.     

Development of radio frequency transmitters including on‐chip antenna for intelligent human sensing systems

This paper presents the essentials of the development of an integrated smart microsensor system that has been developed to monitor the motion and vital signs of humans in various environments. Integration of RF transmitter technology with complementary metal‐oxide‐semiconductor/micro electro mechanical systems (CMOS/MEMS) microsensors is required to realize wireless smart microsensors for the monitoring system. Sensors for the measurement of body temperature, perspiration, heart rate (pressure sensor), and motion (accelerometers) are candidates for integration on the wireless smart microsensor system. In this paper, the development of radio frequency transmitter (RF) that will be integrated on wireless smart microsensors is presented. A voltage controlled RF‐CMOS oscillator (VCO) has been fabricated for the 300‐MHz frequency band applications. Also, spiral inductors for an LC resonator and an integrated antenna have been realized with a CMOS‐compatible metallization process. The essential RF components have been fabricated and evaluated experimentally. The fabricated CMOS VCO showed a conversion factor from voltage to frequency of about 81 MHz/V. After matching the characteristic impedance (50 Ω) of the on‐chip integrated antenna and the VCO output, more than 5 m signal transmission from the microchip antenna has been observed. The transmitter showed remarkable improvement in transmission power efficiency by correct matching with the microchip antenna. Essential technologies of the RF transmitter for the wireless smart microsensors have been successfully developed. Also, for the 300‐MHz band application, the integrated RF transmitter, with the CMOS oscillator and the on‐chip antenna, has been successfully demonstrated for the first time. Copyright © 2007 Institute of Electrical Engineers of Japan© 2007 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Low‐voltage rail‐to‐rail switched buffer topologies

This paper presents some CMOS rail‐to‐rail low‐voltage (1.2 V) switched buffer topologies, to be used as input stages in switched‐opamp circuits. The main buffer is based on the use of an op‐amp featuring rail‐to‐rail input and output swing with constant transconductance over the input common mode voltage. The designed buffer exhibits a total harmonic distortion of about ‐61 dB for 5 MHz clock frequency with 2 V_pp input amplitude. Its characteristics have been compared with those of other rail‐to‐rail switched buffers, based on the main CMOS OTA (simple, symmetrical, Miller), showing good distortion even at frequencies in the MHz range and satisfying the requirements for the series switches. Copyright © 2001 John Wiley & Sons, Ltd.     

Low‐power quadrature generators for body area network applications

This paper presents different alternatives for the implementation of low‐power monolithic oscillators for wireless body area networks and describes the design of two quadrature generators operating in the 2.4‐GHz frequency range. Both implementations have been designed in a 90‐nm Complementary Metal‐Oxide Semiconductor (CMOS) technology and operate at 1 V of supply voltage. The first architecture uses a voltage‐controlled oscillator (VCO) running at twice the desired output frequency followed by a divider‐by‐2 circuit. It experimentally consumes 335 μW and achieves a phase noise of ?110.2 dBc/Hz at 1 MHz. The second architecture is a quadrature VCO that uses reinforced concrete phase shifters in the coupling path for phase noise improvement. Its power consumption is only 210 μW, and it obtains a phase noise of ?111.9 dBc/Hz at 1 MHz. Copyright © 2011 John Wiley & Sons, Ltd.     

67 GHz three‐spiral transformer CMOS oscillator

This paper presents a 67GHz LC oscillator exploiting a three‐spiral transformer and implemented in 65nm bulk complementary metal–oxide–semiconductor technology by STMicroelectronics. The three‐spiral transformer allows operating with a lower voltage supply, still obtaining good phase noise performance, and achieving a compact design. Measured performances when supplied with 1.2 V are: oscillation frequency of 67 GHz, phase noise (PN) equal to ?96 dBc/Hz at 1 MHz frequency offset from the carrier, power consumption (P_C) equal to 19.2 mW and figure of merit (FOM) equal to ?179.7 dB/Hz. Measured performances when supplied with 0.6 V are: oscillation frequency of 67 GHz; PN equal to ?88.7 dBc/Hz at a 1 MHz frequency offset from the carrier; P_C equal to 3.6 mW and FOM equal to ?179.7 dB/Hz. Copyright © 2016 John Wiley & Sons, Ltd.     

Memristor‐based voltage‐controlled relaxation oscillators

This paper introduces two voltage‐controlled memristor‐based reactance‐less oscillators with analytical and circuit simulations. Two different topologies which are R‐M and M‐R are discussed as a function of the reference voltage where the generalized formulas of the oscillation frequency and conditions for oscillation for each topology are derived. The effect of the reference voltage on the circuit performance is studied and validated through different examples using PSpice simulations. A memristor‐based voltage‐controlled oscillator (VCO) is introduced as an application for the proposed circuits which is nano‐size and more efficient compared to the conventional VCOs. Copyright © 2013 John Wiley & Sons, Ltd.     

Wide‐band dual‐resonance capacitive cross‐coupled divide‐by‐5 injection‐locked frequency divider

A wide locking range divide‐by‐5 injection‐locked frequency divider (ILFD) is proposed and was implemented in the TSMC 0.18‐μm 1P6M CMOS process. Conventional divide‐by‐5 ILFD has limited locking range. The proposed divide‐by‐5 ILFD is based on a capacitive cross‐coupled voltage‐controlled oscillator (VCO) with a dual‐resonance resonator, which is implemented in the divide‐by‐5 ILFD to obtain a wide overlapped locking range. At the drain‐source bias V_DD of 0.9 V and at the incident power of 0 dBm, the measured locking range of the divide‐by‐5 ILFD is 3.2 GHz, from the incident frequency 9.4 to 12.6 GHz, the percentage is 29.09%. The core power consumption is 2.98 mW. The die area is 0.987 × 1.096 mm².     

A 60‐GHz power amplifier design with on‐chip tunable load‐matching network and power detect in 90‐nm CMOS

This paper presents a 60‐GHz power amplifier with on‐chip varactor‐based tunable load‐matching networks and an embedded DC temperature‐sensor‐based power detector. The output power can be monitored by the DC temperature sensor, and load‐matching network can be tuned by regulating the control voltage of the varactors, which can be used for correcting unpredictable process, supply voltage, and temperature (PVT) variations and load mismatch. Measured results show that the small‐signal gain of the CMOS power amplifier is up to 6.5 dB at 52 GHz. The power amplifier achieves 5 dBm output P1dB and 7 dBm saturated output power with 4.5% maximun power added efficiency (PAE) at 1 V control voltage. By sweeping the control voltage of the varactors, the power amplifier can obtain the maximun power gain, which can be used to solve the load mismatch. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A common‐mode replica compensated inductor–capacitor voltage‐controlled oscillator for mixed‐signal system‐on‐chip applications

A novel 1.57 GHz complementary metal–oxide semiconductor inductor–capacitor voltage‐controlled oscillator with the common‐mode replica compensation is introduced for mixed‐signal system‐on‐chip applications. In order to alleviate power line disturbances, the center tap node of differential symmetric inductor and the replica biasing circuit are adopted in the differential voltage regulating unit to reduce power supply sensitivity. In addition, this proposed design also leads to low tuning gain and low power dissipation. The post‐layout simulation results under the Taiwan Semiconductor Manufacturing Company's mixed‐signal 0.18 µm 1P6M process show that the proposed design achieves power supply rejection of ?68.6 dB at low frequencies and 1.2 MHz/V pushing sensitivity. It exhibits phase noise of ?130.6 dBc/Hz at a 1 MHz offset from a 1.57 GHz carrier yet dissipates only 5.58 mW under a 1.8 V power supply. Copyright © 2011 John Wiley & Sons, Ltd.     

A subthreshold current‐sensing ΣΔ modulator for low‐voltage and low‐power sensor interfaces

A continuous‐time (CT) ΣΔ modulator for sensing and direct analog‐to‐digital conversion of nA‐range (subthreshold) currents is presented in this work. The presented modulator uses a subthreshold technique based on subthreshold source‐coupled logic cells to efficiently convert subthreshold current to digital code without performing current‐to‐voltage conversion. As a benefit of this technique, the current‐sensing CT ΣΔ modulator operates at low voltage and consumes very low power, which makes it convenient for low‐power and low‐voltage current‐mode sensor interfaces. The prototype design is implemented in a 0.18 µm standard complementary metal‐oxide semiconductor technology. The modulator operates with a supply voltage of 0.8 V and consumes 5.43 μW of power at the maximum bandwidth of 20 kHz. The obtainable current‐sensing resolution ranges from effective number of bits (ENOB) = 7.1 bits at a 5 kHz bandwidth to ENOB = 6.5 bits at a 20 kHz bandwidth (ENOB). The obtained power efficiency (peak FoM = 1.5 pJ/conv) outperforms existing current‐mode analog‐to‐digital converter designs and is comparable with the voltage‐mode CT ΣΔ modulators. The modulator generates very low levels of switching noise thanks to CT operation and subthreshold current‐mode circuits that draw a constant subthreshold current from the voltage supply. The presented modulator is used as a readout interface for sensors with current‐mode output in ultra low‐power conditions and is also suitable to perform on‐chip current measurements in power management circuits. Copyright © 2014 John Wiley & Sons, Ltd.     

Mode dynamics in fourth‐order LC oscillators

We present a complete analysis of single and concurrent modes in fourth‐order LC‐voltage‐controlled oscillators ( VCOs), which are increasingly applied in dual‐band communication systems. We give a procedure based on the averaging method that simplifies the derivation of the abridged equations, which are derived without resorting to a change of co‐ordinates. The amplitudes of the oscillatory modes in steady state and in transient are found in explicit form. Conditions for the stability of the single and concurrent modes are derived, which apply to any active one‐port dual‐band LC‐VCO and allow one to predict the nonlinearities ensuring the occurrence of a stable concurrent mode. Numerical and experimental results show a good accuracy of the presented formulas. Copyright © 2016 John Wiley & Sons, Ltd.     

Output‐capacitorless segmented low‐dropout voltage regulator with controlled pass transistors

This article presents a low quiescent current output‐capacitorless quasi‐digital complementary metal‐oxide‐semiconductor (CMOS) low‐dropout (LDO) voltage regulator with controlled pass transistors according to load demands. The pass transistor of the LDO is segmented into two smaller sizes based on a proposed segmentation criterion, which considers the maximum output voltage transient variations due to the load transient to different load current steps to find the suitable current boundary for segmentation. This criterion shows that low load conditions will cause more output variations and settling time if the pass transistor is used in its maximum size. Furthermore, this situation is the worst case for stability requirements of the LDO. Therefore, using one smaller transistor for low load currents and another one larger for higher currents, a proper trade‐off between output variations, complexity, and power dissipation is achieved. The proposed LDO regulator has been designed and post‐simulated in HSPICE in a 0.18 µm CMOS process to supply a stable load current between 0 and 100 mA with a 40 pF on‐chip output capacitor, while consuming 4.8 μA quiescent current. The dropout voltage of the LDO is set to 200 mV for 1.8 V input voltage. The results reveal an improvement of approximately 53% and 25% on the output voltage variations and settling time, respectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Transformer‐coupled π‐network differential CMOS oscillator circuit topology

This paper reports a novel oscillator circuit topology based on a transformer‐coupled π‐network. As a case study, the proposed oscillator topology has been designed and studied for 60 GHz applications in the frame of the emerging fifth generation wireless communications. The analytical expression of the oscillation frequency is derived and validated through circuit simulations. The root‐locus analysis shows that oscillations occur only at that resonant frequency of the LC tank. Moreover, a closed‐form expression for the quality factor (Q) of the LC tank is derived which shows the enhancement of the equivalent quality factor of the LC tank due to the transformer‐coupling. Last, a phase noise analysis is reported and the analytical expressions of phase noise due to flicker and thermal noise sources are derived and validated by the results obtained through SpectreRF simulations in the Cadence design environment with a 28 nm CMOS process design kit commercially available. Copyright © 2016 John Wiley & Sons, Ltd.     

0.5‐V bulk‐driven differential amplifier

A new 0.5‐V fully differential amplifier is proposed in this article. The structure incorporates a differential bulk‐driven voltage follower with conventional gate‐driven amplification stages. The bulk‐driven voltage follower presents differential gain equal to unity while suppressing the input common‐mode voltage. The amplifier operates at a supply voltage of less than 0.5 V, performing input transconductance almost equal to a gate transconductance and relatively high voltage gain without the need for gain boosting. The circuit was designed and simulated using a standard 0.18‐µm CMOS n‐well process. The low‐frequency gain of the amplifier was 56 dB, the unity gain bandwidth was approximately 3.2 MHz, the spot noise was 100 nV/√Hz at 100 kHz and the current consumption was 90 μΑ. Copyright © 2012 John Wiley & Sons, Ltd.     

A 1.2 V 83 dB DR single‐ended input SC ΔΣ modulator including a large‐swing analog buffer for portable ECG applications

This study proposes a subsystem consisting of an analog buffer and a single‐ended input to a fully differential ΔΣ modulator to obtain low‐power consumption for portable electrocardiogram applications. With the proposed subsystem, the need for an inverting amplifier is avoided, and low‐power consumption is achieved. The ΔΣ modulator with a second order, 1 bit, and cascade of integrators feedforward structure consumes a low power, in which an inverting and a non‐inverting path implement a single‐ended input to fully‐differential signals. A double sampling technique is proposed for a digital‐to‐analog converter feedback circuit to reduce the effect of the reference voltage, reduce the amplifier requirements, and obtain low‐power consumption. Input‐bias and output‐bias transistors working in the weak‐inversion region are implemented to obtain an extremely large swing for the analog buffer. At a supply voltage of 1.2 V, signal bandwidth of 250 Hz, and sampling frequency of 128 kHz, the measurement results show that the modulator with a buffer achieves a 77 dB peak signal‐to‐noise‐distortion ratio, an effective‐number‐of‐bits of 12.5 bits, an 83 dB dynamic range, and a figure‐of‐merit of 156 dB. The total chip size is approximately 0.28 mm² with a standard 0.13 µm Complementary Metal‐Oxide‐Silicon (CMOS) process. Copyright © 2016 John Wiley & Sons, Ltd.     

A 0.6‐V sub‐mW X‐band RFSOI CMOS LNA with novel complementary current‐reused technique

A fully integrated 0.6 V low‐noise amplifier (LNA) for X‐band receiver application based on 0.18 μm RFSOI CMOS technology is presented in this paper. To achieve low noise and high gain with the constraint of low voltage and low power consumption, a novel modified complementary current‐reused LNA using forward body bias technique is proposed. A diode connected MOSFET forward bias technique is employed to minimize the body leakage and improve the noise performance. A notch filter isolator is constructed to improve the linearity of low voltage. The measured results show that the proposed LNA achieves a power gain of 11.2 dB and a noise figure of 3.8 dB, while consuming a DC current of only 1.6 mA at supply voltage of 0.6 V. Copyright © 2017 John Wiley & Sons, Ltd.