Preparation and properties of porous ceramics from nickel slag by aerogel gelcasting

To further resource industrial solid waste, porous ceramics with high porosity were prepared by a gelcasting method using nickel slag and kaolin as raw materials and hydrophilic nontoxic SiO₂ aerogel as a gelling agent. The effects of nickel slag content, dispersant and solid content on the properties and microstructure of porous ceramics were investigated in detail in terms of density, compressive strength, porosity, phase composition and micromorphology. The results confirmed that a certain amount of nickel slag can effectively improve the porosity of porous ceramics, while the addition of dispersant can promote the flow of the slurry, enhanced the denseness of the raw billet and significantly improved the compressive strength. However, its excessive use had a negative effect on the ceramic density and porosity. At the same time, the solid content played a key role in the performance of porous ceramics prepared by gelcasting, and too much solid content was also not conducive to the generation of pores. When the nickel slag content was 55%, the amount of dispersant was 2%, and the solid content was 60 vol%, the porous ceramic had a better overall performance, the density of the porous ceramic was 510 kg/m³, the compressive strength was 1.3 MPa, and the porosity reached 80.1%. The major crystalline phases of porous ceramics prepared by nickel slag were cordierite and anorthite.     

Alumina/zirconia ceramic membranes fabricated by temperature induced forming technique

It is well known that the fabrication technique of porous ceramic composites has a significant effect on their microstructure and properties. In the present study, alumina/zirconia ceramic composites doped with magnesia were fabricated by temperature induced forming technique using tri-ammonium citrate and polyacrylic acid (PAA) as dispersant and gelling agents, respectively. The zirconia content was up to 20 wt% and added at the expense of alumina while the magnesia content was up to 2 wt% over the total mass. The optimum amount of ammonium citrate tribasic needed for dispersing the ceramic slurry was determined by measuring zeta potential of slurries. The prepared green alumina/zirconia composites were subjected for solid state sintering at 1550 °C for 1 h. The densification parameters, phase composition, average pore diameter, microstructure and cold crushing strength of sintered alumina/zirconia ceramics were investigated by the suitable techniques. The results revealed that the addition of tri-ammonium citrate to ceramic slurries enhanced the zeta potential which reached ?28.3 mV by adding 1 wt.-%. The bulk density was decreased while the apparent porosity was increased with the increase of zirconia content. The apparent porosities of sintered porous composites were in the range of 38.8–48.5%. The average pore diameter for the composite containing 15% zirconia was 1.79 μm and pore volume was 0.11 ml/g. The obtained microstructure exhibited zirconia grains located on the grain boundaries of Al₂O₃ matrix. The existence of zirconia in addition to magnesia hindered the growth and deformation of the matrix. The cold crushing strength of porous composites was decreased from 16.0 to 8.5 to MPa by increasing the zirconia content from 5 to 20 wt.-%.     

Ammonium hydrogen carbonate provided viscous slurry foaming—A novel technology for the preparation of porous ceramics

In current research a novel technology for the preparation of porous ceramics was developed. The ammonium hydrogen carbonate was used as foaming agent for the generation of pores in the glycerol-based viscous ceramic slurry. Total and open porosity of obtained ceramics depends on the amount and granulometric distribution of NH₄HCO₃ as well as particle size of HAp powder used for the preparation of viscous slurry. Varying amount of NH₄HCO₃ in the range from 0 to 2.75 wt.%, open and total porosity increased from 25 to 69% and from 32 to 73% respectively. The formation of well-connected open porosity with irregularly shaped pores was observed for sintered ceramics.     

Preparation of foamed ceramics from steel slag with high calcium and iron content

In this paper, steel slag foamed ceramics were fabricated by using steel slag, kaolin, feldspar, and quartz as main raw materials, and adding SiC as high-temperature foaming agent. The effects of steel slag content and SiC particle size on porosity and mechanical properties of foamed ceramics were researched. Results indicate that when content of steel slag is 40 wt%, and particle size of SiC is 20 µm, foamed ceramics exhibited optimized properties: water absorption rate of 2.59%, total porosity of 55.91%, bulk density of 1.33 g·cm⁻³, and compressive strength of 1.21 MPa. The results show that with the increase of steel slag content, the phase composition of foamed ceramics changes, and foam process is hindered. The increase of steel slag content contributes to the formation of diopside. Fe³⁺, Fe²⁺ in liquid phase enter into diopside by solid solution, the amount of liquid phase decreases. Liquid phase mass transfer slows down, and content of SiC in liquid phase decreases, so that the porosity decreases. At the same steel slag content, different SiC particle size affects the difference between pressure inside the closed pore and surface pressure, thereby the porosity changes.     

Preparation and characterization of porous ceramics from nickel smelting slag and metakaolin

Porous ceramics with high porosity and low bulk density were prepared by using nickel slag and metakaolin as the primary raw materials, glass powder as flux, and SiC as the foaming agent. The content of nickel slag and foaming agent had a significant effect on the bulk density, porosity, and flexural strength of the porous ceramics. The porous ceramics with the best properties were obtained at 1100 °C for 30 min with 50 wt% nickel slag, 40 wt% metakaolin, 10 wt% waste glass, and 0.8 wt% SiC. It had a low bulk density (as low as 245 kg/m³), high flexural strength and compressive strength (0.6 MPa and 1.17 MPa, respectively), and high porosity (about 89.8%). The nickel slag was magnetically separated as well. The density of nickel slag powder could be reduced via magnetic separation, and there was no significant change in the crystal structure of the raw material. Compared with porous ceramics prepared using nickel slag without magnetic separation, ceramics subjected to magnetic separation had lower bulk density, higher porosity, and the same phase composition. This study can be used as an indicator for the application of nickel slag in porous ceramics, which is of great significance in providing a great substitute nickel slag towards recovery and utilization.     

造孔剂和增强剂对工业固废基多孔陶瓷性能的影响

以镁渣,粉煤灰为原料,添加造孔剂(电石渣、碳粉)和增强剂(高岭土、膨润土)制备多孔陶瓷,并研究造孔剂和增强剂种类和含量对多孔陶瓷性能的影响.结果表明,添加造孔剂后,多孔陶瓷的烧失率、吸水率和气孔率升高,体积密度和强度降低.同等含量时,碳粉具有较好的造孔效果;多孔陶瓷的烧失率、吸水率和气孔率最高可分别达到30％,38％和53％,体积密度最小达到1.4 g/cm3;添加增强剂后,多孔陶瓷的强度大为提高,但其吸水率、气孔率降低,体积密度增加.高岭土的含量不大于10％时,其粘结增强效果明显优于同等含量膨润土的;多孔陶瓷的压缩强度可至28 MPa.     

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Porous ceramics derived from steel slag/coal gangue mixtures using cigarette butts as the pore-forming agent

Fabrication of ceramic materials with interconnected pores is necessary to improve thermal energy storage efficiency in high-temperature infiltration technology. In the present study, industrial wastes such as coal gangue, steel slag, etc., were selected as the raw materials to prepare ceramics with interconnected pores. By adopting 50% cigarette butts as the pore-forming agent, steel slag–coal gangue mixtures with a mass ratio of steel slag to coal gangue of 1:9 were sintered at 1100°C, and ceramics with interconnected elongated pores were prepared successfully. The highest apparent porosity and lowest volume density of the as-prepared ceramics were ca. 73% and .74 g/cm³, respectively. Further measurements of the thermophysical properties indicated that no obvious mass loss was observed in the temperature range from ambient temperature to 800°C. The maximum values of specific heat and thermal conductivity were 1.38 J/(g K) and 1.661 W/(m K), respectively, and meanwhile the minimum compressive strength could exceed 3.5 MPa. These research results implied that the as-prepared steel slag–coal gangue ceramics can provide long-term service and offer excellent thermal stability over a wide temperature range. Therefore, they should have potential applications in high-temperature infiltration technology.     

Effects of added aluminum chromium slag on the structure and mechanical properties of colored zirconia ceramics

Colored zirconia ceramic samples were prepared via pressureless sintering with yttria-stabilized zirconia as a raw material and aluminum chromium slag (ACS) as an additive. Then, the effects of added ACS (0-15.0 wt%) on the microstructure, phase composition, and mechanical properties of the ceramic were investigated. The addition of ACS changed the apparent color of zirconia ceramics from white to pink, and the color deepened as the ACS content increased. In addition, more pores appeared in the sintered ceramic substrate as the content of ACS increased, and the relative density of samples declined from 97.7% to 91.1% with an increase in ACS content. However, the microhardness and bending strength each reached their maximum values (1887.2 HV and 433.5 MPa, respectively) when the content of ACS was 5.0 wt%. Fracture surface analysis of the samples showed that intergranular fractures were the main features of sintered samples with no added ACS, whereas numerous transgranular fractures occurred in sintered samples to which ACS had been added. The XRD results revealed that the prepared mainly composite ceramics were composed of t-ZrO₂, m-ZrO₂, and chromium-corundum, and the content of the t-ZrO₂ gradually increased as the ACS content increased.     

泡沫陶瓷的研制

泡沫陶瓷是一种新型的功能陶瓷材料。它具有独特的结构和性能，在工业中有着广泛的应用前景。泡沫陶瓷具有密度小、透气性高、耐高温、抗化学腐蚀等特性。本研究对用颗粒强化的氧化铝骨架合成泡沫陶瓷进行了分析。这种材料比其它多孔陶瓷材料具有更好的热化学性质。这种材料可以用有机海绵浸浆获得，然后烧去海绵，留下多孔陶瓷网。这种方法的优点是它包含了过程参数和陶瓷结构，同时合成物的烧结情况及其它条件的影响在文中也有阐述。     

Preparation of near net size porous alumina-calcium aluminate ceramics by gelcasting-pore-forming agent processs

In the processing of porous ceramics, shrinkage from green body to sintered compact during drying and sintering is one of the key concerns which affect microstructure and properties of porous ceramics. Through releasing gases from the burning of the pore forming agents, and volume expansion from the formation of low density resultants during sintering, the sintering shrinkage can be effectively compensated and near net size preparation can be achieved. Herein, near net size porous alumina-calcium aluminate ceramics with controllable shrinkage have been prepared using a combination of gelcasting and pore-forming agent process by adjusting the amount of CaCO₃ and polymethyl methacrylate (PMMA) microspheres added. Al₂O₃ and CaCO₃ were used as raw materials, PMMA microspheres were used as pore-forming agent, isobutylene/maleic anhydride copolymer (Isobam104) was used as gelling agent and dispersing agent. The effects of the addition amounts of CaCO₃ and PMMA in the slurry on the phase composition, shrinkage, porosity, and strength of porous alumina-calcium aluminate ceramics were investigated. The results show that as the CaCO₃ addition amount increases from 0 to 20 wt%, the shrinkage of the samples gradually decreases from 7.3% to −1.4%, and the consequent porosity increases from 58% to 66%, while the compressive strength increases from 5.9 to 15.5 MPa. When PMMA content increases from 10 to 50 wt%, the shrinkage of the samples decreases first and then increases, the porosity increases from 51% to 74%, and the compressive strength decreases from 12.5 to 5.3 MPa. The mechanisms for controlling shrinkages during preparation of porous alumina-calcium aluminate ceramics can be attributed to the following aspects: on one hand, gas release from burning of PMMA and decomposition of CaCO₃ during sintering; on the other hand, volume expansion due to the formation of lower density calcium aluminates which come from the reactions between CaO and Al₂O₃. The near net size preparation technique is of great significance for the manufacture of porous ceramics since the subsequent machining cost can be effectively reduced.     

Porous yttria‐Stabilized Zirconia Ceramics Fabricated by Nonaqueous‐Based Gelcasting Process with PMMA Microsphere as Pore‐Forming Agent

Porous yttria‐stabilized zirconia (YSZ) ceramics were fabricated using tert‐butyl alcohol (TBA)‐based gelcasting with monodisperse polymethylmethacrylate (PMMA) microspheres as both pore‐forming agent and lubricant agent. The TBA‐based slurry of 50 vol% solid loading with excellent rheological properties appropriate for casting was successfully prepared by using a commercial polymer dispersant DISPERBYK‐163 as both dispersant and stabilizer. The distribution of the spherical pores made from PMMA microspheres was very homogeneous. Their average diameter decreased from 16.9 to 15.7 μm when the sintering temperature was increased from 1350°C to 1550°C. The compressive strength increased from 14.57 to 142.29 MPa and the thermal conductivity changed from 0.17 to 0.65 W/m·K when the porosity decreased from 71.6% to 45.1%. The results show that this preparation technology can make all the main factors controllable, such as the porosity, the size and shape of pores, the distribution of pores, and the thickness and density of pore walls. This is significant for fabricating porous ceramics with both high compressive strength and low thermal conductivity.     

Cellular zirconia ceramics processed by direct emulsification

Highly porous zirconia ceramics for prospective use as separators in alkaline electrolysis cells have been processed by emulsification of paraffin in concentrated zirconia suspensions. Effects of processing parameters on porosity, cell size distribution, and pore interconnectivity are studied through Taguchi statistical design. The porosity of zirconia ceramics has shown a strong correlation with paraffin-to-suspension ratio employed in emulsification. High paraffin-to-suspension ratios combined with high gelatin content in the emulsion are beneficial for creating highly porous cellular materials with interconnected cell sizes. The attained microstructural features allow high percolation of ionic species in these highly porous ceramics after impregnation with aqueous electrolytes, facilitating charge transport within the liquid medium inside the ceramic bodies, as required for lower ohmic losses. This work provides guidelines for developing efficient ceramic separators for future use in alkaline electrolysis cells and other applications requiring thermally and chemically-stable ceramics with high and well-interconnected porosity.     

Organic mesh template-based laminated object manufacturing to fabricate ceramics with regular micron scaled pore structures

A new aqueous slurry-based laminated object manufacturing process for porous ceramics is proposed: firstly, an organic mesh sheet is pre-paved as a pore-forming template before slurry layer scraping; secondly, the 2D pattern is built with laser outline cutting of the dried mesh–ceramic composite layer; finally, the pore structure is formed after degreasing and sintering. Alumina parts with porosities of 51.5 %, round hole diameters of 80 ± 5 μm were fabricated using 70 wt. % solid content slurry and 100 mesh nylon net. Using an organic mesh as the framework and template not only reduces the risk of damage of the green body but also ensures the regularity, uniformity and connectivity of the micron scaled pore network. The layer-by-layer drying method avoids the delamination phenomenon and improves the paving density. The new method can realize the flexible design of the pore structure by using various organic mesh templates.     

Phase-inversion tape casting and synchrotron-radiation computed tomography analysis of porous alumina

A variant of tape casting based on the phase inversion phenomenon was adopted for fabrication of porous ceramic wafer. A slurry was prepared by dispersing alumina powder in an N-methyl-2-pyrrolidone (NMP) solution of the polymers polyethersulfone (PES) and polyvinylpyrrolidone (PVP). The slurry was cast using a doctor blade, and immersed in water to solidify the polymer solution via phase inversion. The green tape was dried and sintered at 1500 °C. The as-prepared ceramic wafer was characterized using synchrotron-radiation computed tomography (SR-CT). It was revealed that the ceramic wafer contained typical finger-like macrovoids, and the porosity resulting from these macrovoids was ~30%. The overall porosity of the wafer was 59%, as derived from the density data measured by Archimedes method in mercury. It is concluded that the phase inversion tape casting is a simple and effective method for preparation of porous ceramics.     

Tailoring the pore structure and property of porous biphasic calcium phosphate ceramics by NaCl additive

This study investigated the effects of NaCl additive on the phase composition, pore structure and mechanical property of porous biphasic calcium phosphate (BCP) ceramics, which were prepared by freeze-casting. The results indicated that the addition of NaCl promoted transformation of β-tricalcium phosphate to hydroxyapatite in the BCP ceramics; the OH group in HA phase of BCP ceramic was partially replaced by chloride ion. As the mass fraction of NaCl in the slurry increased from 0 to 3%, the porosity of obtained porous BCP ceramics decreased from 77.76% to 60.22%; the average width of dendritic pores increased from 74.37 µm to 111.27 µm; the compressive strength achieved threefold increase. As the amount of NaCl additive reached 4.5%, the porosity, pore width, and compressive strength of the porous BCP ceramics were comparable with those modified by 3% NaCl. NaCl is regarded as an effective additive to tailor the pore structure and property of freeze-cast porous ceramics.     

Effect of zirconia content and particle size on the properties of 3D-printed alumina-based ceramic cores

Alumina-based ceramic cores are used to manufacture the internal structures of hollow alloy blades, requiring both high precision and moderate properties. In this work, zirconia is regarded as a promoter to improve the mechanical properties of sintered ceramic. The effect of zirconia content and particle size on the microstructure and mechanical properties of ceramics was evaluated. The results indicate that the flexural strength of sintered ceramics reached the maximum of 14.5 ± 0.5 MPa when 20 wt% micron-sized (10 μm) zirconia (agglomerate size, consistent with the alumina particle size) was added, and 26.5±2.5 MPa when 15 wt% 0.3 μm zirconia was added. Zirconia with submicron-sized (0.3 μm) particles effectively filled the pores between alumina particles, thus leading to the maximum flexural strength with a relatively low content. The corresponding sintered ceramics had a bulk density of 2.0 g/cm³ and open porosity of 59.6%.     

Effect of technological parameters on densification of reaction bonded Si/SiC ceramics

Si/SiC composite ceramics was produced by reaction sintering method in process of molten silicon infiltration into porous C/SiC preform fabricated by powder injection molding followed by impregnation with phenolic resin and carbonization. To optimize the ceramics densification process, effect of slurry composition, debinding conditions and the key parameters of all technological stages on the Si/SiC composite characteristics was studied. At the stage of molding the value of solid loading 87.5% was achieved using bimodal SiC powder and paraffin-based binder. It was found that the optimal conditions of fast thermal debinding correspond to the heating rate of 10?°C/min in air. The porous C/SiC ceramic preform carbonized at 1200?°C contained 4% of pyrolytic carbon and ～25% of open pores. The bulk density of Si/SiC ceramics reached 3.04?g/cm³, silicon carbide content was 83–85?wt.% and residual porosity did not exceed 2%.     

Near‐Net‐Shaped Porous Ceramics for Potential Sound Absorption Applications at High Temperatures

We present an interesting processing route for obtaining alumina/mullite‐based ceramics with controlled porosity and airflow resistance leading to promising microstructures for application as sound absorbers. The use of ceramic materials aims for potential applications where high temperatures or corrosive atmospheres are predominant, e.g., in combustion chambers of gas turbines. For the production of the porous ceramics we combined freeze gelation and sacrificial templating processes to produce near‐net‐shaped parts with low shrinkage (<3%) based on environmental‐friendly and low cost conditions. The obtained microstructure presents a bimodal pore size distribution, with small pores derived from the freeze gelation process (~30 μm) connecting large pores (2–5 mm diameter) originated from the expanded polystyrene template particles. These connections, called “windows” in this study, show a significant impact on the sound absorption properties, allowing the pressure diffusion effect to take place, resulting in a significant improvement of the sound absorption coefficient. By varying the template particle content and the slurry solid content, it is possible to control the sound absorption behavior at different frequencies of the open‐celled ceramics. These ceramics feature a high open porosity, from 77% to 82%, combined with sufficient compressive strength ranging from 0.27 to 0.68 MPa and sound absorption coefficients of 0.30–0.99, representing a highly promising combination of properties for noise control and reduction at corrosive environments and high temperatures.     

Highly porous silica foams prepared via direct foaming with mixed surfactants and their sound absorption characteristics

The highly porous silica ceramics were fabricated by direct foaming with mixed surfactants and the influence of silicon nitride addition and solid content on the microstructures and properties were investigated. The results showed that silicon nitride can impede the formation of cristobalite and facilitates the sintering of silica ceramics. When the addition of silicon nitride powders reached 15 wt%, the highest compressive strength of silica ceramic foams could be obtained. The porosity of silica ceramic foams was tailored in the range of 84.61%–91.35% by adjusting the solid content, and the compressive strength of the obtained ceramic foams ranged from 5.89 MPa to 0.94 MPa. Sound absorption characteristics of silica ceramics foams were investigated. With the porosity of ceramic foams increased from 84.61% to 91.35%, the sound absorption coefficients in the entire sound wave frequency were enhanced due to the reduction of flow resistances, besides, the sound absorption peak varied from 4200 Hz to 2300 Hz, and became more intense and sharper.