Luminescence and self-referenced optical temperature sensing performance in Ca2YZr2Al3O12:Bi3+,Eu3+ phosphors

Ca₂YZr₂Al₃O₁₂:Bi³⁺,Eu³⁺ phosphors were elaborated by a traditional solid-state reaction method. The luminescence of Ca₂YZr₂Al₃O₁₂:Bi³⁺ samples, energy transfer from Bi³⁺ to Eu³⁺, and the temperature sensing properties of Ca₂YZr₂Al₃O₁₂:Bi³⁺,Eu³⁺ samples have been systematically researched. Under the excitation of ultraviolet light, Bi³⁺ single doped phosphors give 313 and 392 nm emission bands, which origin from the substitutions of Bi³⁺ instead of Ca²⁺ and Y³⁺ sites, respectively. And the color-adjustable emission from blue to red were observed by increasing Eu³⁺ content in Ca₂YZr₂Al₃O₁₂:Bi³⁺,Eu³⁺ samples. Relying on different temperature dependent variation tendency, the fluorescence intensity ratio (FIR) values present outstanding temperature sensing properties. The absolute and relative sensitivity can be up to 0.826 %K^-1 and 0.664 %K^-1, respectively. All above results suggest that Ca₂YZr₂Al₃O₁₂:Bi³⁺,Eu³⁺ phosphor is a potential alternative for optical thermometer.     

Novel AMoO4:Eu3+ (A = Ca and Ba) optical thermometer: Investigation of effect of local ionic coordination environment on optical performance and temperature measurement sensitivity

A range of Eu³⁺-doped AMoO₄ (A = Ca and Ba) phosphors were successfully synthetized, and their crystal structures, optical performance, and temperature measurement sensitivities were investigated in detail. Peak doping concentration of CaMoO₄:Eu³⁺ phosphor was 0.18, while peak doping concentration of BaMoO₄:Eu³⁺ phosphor may be greater than 0.18. Then, temperature-dependent photoluminescence emission spectra of representative CaMoO₄:0.09Eu³⁺ and BaMoO₄:0.03Eu³⁺ phosphors were recorded. CaMoO₄:0.09Eu³⁺ phosphor exhibited abnormal thermal quenching, which was attributed to defects caused by heterovalent substitution of ions and increase in the temperature, and good thermal stability. Finally, the possibility of using both phosphors as optical thermometers was discussed, which exhibited good temperature sensitivity. However, CaMoO₄:0.09Eu³⁺ phosphor exhibited two peak absolute (Sa, 1.28 %K⁻¹ and 1.39 %K⁻¹) and relative sensitivities (Sr, 1.21 %K⁻¹ and 1.20 %K⁻¹). In addition, variation trend of Sr value with temperature was considerably peculiar. Two optimum Sa and Sr values were attributed to abnormal thermal quenching of CaMoO₄:0.09Eu³⁺ phosphor. Peak Sa and Sr values of BaMoO₄:0.03Eu³⁺ phosphor was 12.39 %K⁻¹ and 0.89 %K⁻¹, respectively. In addition, Sa of AMoO₄:Eu³⁺ phosphor was negatively related to Eu³⁺ central asymmetry, while peak Sr value was more inclined to appropriate ionic central asymmetry.     

Energy transfer and color-tunable emission in Ba2Y2Si4O13:Bi3+,Eu3+ phosphors

Single-composition Ba₂Y₂Si₄O₁₃:Bi³⁺,Eu³⁺ (BYSO:Bi³⁺,Eu³⁺) phosphors with color-tunable and white emission were prepared by conventional high temperature solid-state reaction method. The structural and luminescent properties of these phosphors were thoroughly investigated through X-ray diffraction, photoluminescence, and decay curves. BYSO:Bi³⁺ phosphors show two excitation peaks at 342 and 373 nm, and give two emission peaks at 414 and 503 nm, respectively, indicating that there are two sites of Bi³⁺ in BYSO. The energy transfer from Bi³⁺ to Eu³⁺ was investigated in detail. Varied hues from blue (chromaticity coordinate [0.219, 0.350]) to white (0.288, 0.350) and orange-red light (0.644, 0.341) can be generated by adjusting the content of Eu³⁺. Pure white light emission (0.311, 0.338) can be obtained under the excitation of 355 nm in BYSO:3%Bi³⁺,20%Eu³⁺ phosphor. Besides, BYSO:Bi³⁺,Eu³⁺ phosphors exhibit distinct thermal quenching properties, whose emission intensity at 473 K is 82.6% of that at 298 K. Our results indicate that BYSO:Bi³⁺,Eu³⁺ may be applied as conversion phosphors for n-UV-based W-LEDs.     

Tunable color emission in LaScO3:Bi3+,Tb3+,Eu3+ phosphor

LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ (x = 0 − 0.04, y = 0 − 0.05, z = 0 − 0.05) phosphors were prepared via high-temperature solid-state reaction. Phase identification and crystal structures of the LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ phosphors were investigated by X-ray diffraction (XRD). Crystal structure of phosphors was analyzed by Rietveld refinement and transmission electron microscopy (TEM). The luminescent performance of these trichromatic phosphors is investigated by diffuse reflection spectra and photoluminescence. The phenomenon of energy transfer from Bi³⁺ and Tb³⁺ to Eu³⁺ in LaScO₃:xBi³⁺,yTb³⁺,zEu³⁺ phosphors was investigated. By changing the ratio of x, y, and z, trichromatic can be obtained in the LaScO₃ host, including red, green, and blue emission with peak centered at 613, 544, and 428 nm, respectively. Therefore, two kinds of white light-emitting phosphors were obtained, LaScO₃:0.02Bi³⁺,0.05Tb³⁺,zEu³⁺ and LaScO₃:0.02Bi³⁺,0.03Eu³⁺,yTb³⁺. The energy transfer was characterized by decay times of the LaScO₃:xBi³⁺, yTb³⁺, zEu³⁺ phosphors. Moreover absolute internal QY and CIE chromatic coordinates are shown. The potential optical thermometry application of LaScO₃:Bi³⁺,Eu³⁺ was based on the temperature sensitivity of the fluorescence intensity ratio (FIR). The maximum S_a and S_r are 0.118 K⁻¹ (at 473.15 K) and 0.795% K⁻¹ (at 448.15 K), respectively. Hence, the LaScO₃:Bi³⁺,Eu³⁺ phosphor is a good material for optical temperature sensing.     

Deep blue,cyan, orange-red,and white multicolor emissions generated by Bi3+/Eu3+ activated KBaYSi2O7 luminescent materials for white light-emitting diodes

A variety of Bi³⁺ and/or Eu³⁺ doped KBaYSi₂O₇ phosphors with deep blue, cyan, orange-red, and white light multicolor emissions have been fabricated by a Pechini sol-gel (PSG) method. The KBaYSi₂O₇:Bi³⁺ phosphors exhibit an intense cyan emission or a unique narrow deep blue emission when excited by different wavelengths, which may bridge the cyan gap or act as a promising deep blue phosphor for white light-emitting diodes (WLEDs). The tunable multicolor emissions can be achieved by changing the Bi³⁺ doping concentrations. The Bi³⁺/Eu³⁺ co-doped KBaYSi₂O₇ phosphors display intrinsic emissions of Bi³⁺ and Eu³⁺ and an energy transfer process between Bi³⁺ and Eu³⁺ can be detected. The luminescence colors of KBaYSi₂O₇:Bi³⁺,Eu³⁺ regularly shift from blue, through cold and warm white, finally toward orange-red by adjusting the relative doping concentrations of Bi³⁺ and Eu³⁺. The single-phase white light-emitting material can be generated in both cold and warm white regions by simply varying the Eu³⁺ doping concentrations. Furthermore, three kinds of WLEDs devices are fabricated by KBaYSi₂O₇:Bi³⁺ or KBaYSi₂O₇:Bi³⁺,Eu³⁺ phosphors, which can exhibit dazzling white light emissions with eminent CIE coordinates, correlated color temperature, and color rendering index. The result offers direct evidence that the as-synthesized phosphors may be potentially applied in WLEDs and solid-state lighting.     

Effect of ligand environment of rare-earth ions on temperature measurement performance of SrAO4:xEu3+ (A = Mo and W) phosphors

Molybdate and tungstate with scheelite-type structure are excellent self-luminescent materials, which can be used as ideal hosts for the doping of rare-earth ions. In this study, a series of Eu³⁺-activated SrAO₄ (A = Mo and W) phosphors were successfully synthesized, and their crystal structures, photoluminescence properties, and temperature measurement performance were analyzed in detail. These phosphors were excited by UV light (291 nm and 247 nm, respectively), with clear energy transfer (ET) (MoO₄^2?→Eu³⁺ or WO₄^2?→Eu³⁺). According to fluorescence intensity ratio (FIR) and Judd–Ofelt (J–O) theory, compared to SrWO₄:0.01Eu³⁺ phosphor, SrMoO₄:0.01Eu³⁺ phosphor exhibited better thermal stability, with relatively low Sa value (maximum values were 5.082 %K^?1 and 20.74 %K^?1, respectively), and their Sr values were not significantly different (maximum values were 0.864 %K^?1 and 0.83 %K^?1, respectively). Sa value was negatively correlated to central asymmetry of Eu³⁺, but the optimal Sr value tended to be more suitable for central asymmetry of Eu³⁺. In addition, Eu³⁺ exhibited stronger central asymmetry as well as covalency of Eu–O bond in SrMoO₄. Results reveal that SrMoO₄:xEu³⁺ and SrWO₄:xEu³⁺ can be used for luminescent thermometers.     

Red,green and blue-violet emission coexistence in white-light-emitting Ca3SiO4Cl2:Bi3+, Li+, Eu2+, Eu3+ phosphor

A series of emission-tunable Ca₃SiO₄Cl₂:Bi³⁺, Li⁺, Euⁿ⁺(n =2, 3) (CSC:Bi³⁺, Li⁺, Euⁿ⁺) phosphors have been synthesized via sol-gel method. The X-ray diffraction results indicate that the as-synthesized phosphors crystallize in a low temperature phase with the space group of P21/c. Energy transfer from Bi³⁺ to Eu³⁺/Eu²⁺ exists in CSC:Bi³⁺, Li⁺, Euⁿ⁺ phosphors. Under the excitation of 327 or 365 nm, the Ca_2.98−ySiO₄Cl₂:0.01Bi³⁺, 0.01Li⁺, yEuⁿ⁺(y=0.0001–0.002) phosphors show an intense green emission band around 505 nm, while under the excitation of 264 nm, three emission bands centered around 396 nm (Bi³⁺), 505 nm (Eu²⁺) and 614 nm (Eu³⁺) are observed and tunable colors from blue-violet to green or white are achieved in these phosphors by varying the content of Eu. White-light emission with the color coordinate (0.312, 0.328) is obtained in Ca_2.978SiO₄Cl₂:0.01Bi³⁺, 0.01Li⁺, 0.002Euⁿ⁺(n =2, 3). Based on these results, the as-prepared CSC:Bi³⁺, Li⁺, Eu²⁺, Eu³⁺ phosphors can act as color-tunable and single-phase white emission phosphors for potential applications in UV-excited white LEDs.     

Luminescence and temperature-sensing properties of Y4GeO8:Bi3+,Eu3+ phosphor

In this paper, Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor with dual emission centers was elaborated via conventional solid-state reaction technology. Thorough research on the structure, morphology, and luminous properties of Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor, the potential applications in optical thermometry were investigated by means of fluorescence intensity ratio and thermochromic techniques. Under 290 and 347 nm excitation, Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor presents broadband emission from ³P₁ → ¹S₀ transition of Bi³⁺ ions and characteristic emission peaks from 4f–4f transition of Eu³⁺ ions. Outstanding temperature-sensing capabilities are acquired from Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor. The maximum relative sensitivity (S_r) can attain 1.51% K⁻¹ (λ_ex = 290 nm). With temperature raising (303–513 K), the emitted color of Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor (λ_ex = 290 nm) shifts from faint yellow to red with a high chromaticity shift (0.180), which can be distinguished by the unaided eye clearly. Our results indicate that Y₄GeO₈:Bi³⁺,Eu³⁺ phosphor has potential applications in optical temperature measurement and high-temperature safety marker.     

White light emitting from YVO4/Y2O3:Eu3+,Bi3+ composite phosphors for UV light-emitting diodes

A series of (1−x)YVO₄/xY₂O₃:Eu³⁺_0.006,Bi³⁺_0.006 (0≤x≤0.54) composite phosphors was synthesized in one step by high temperature solid state reaction and the photoluminescence properties were investigated. By means of co-doping Eu³⁺ and Bi³⁺ ions into the composite matrices composed of YVO₄ and Y₂O₃ crystals, the YVO₄/Y₂O₃:Eu³⁺,Bi³⁺ phosphor exhibits simultaneously the blue (418 nm), green (540 nm) and orange-red (595, 620 nm) emissions. The broad blue and green emissions are attributed to the ³P₁–¹S₀ transitions of Bi³⁺ ion both in Y₂O₃ and in YVO₄ matrices. Moreover, the sharp orange-red emissions are attributed to the ⁵D₀–⁷F_1,2 transitions of Eu³⁺ ion in YVO₄ matrix. By tuning the mole ratio of YVO₄/Y₂O₃ matrices the white light-emitting could be obtained. The results indicated that when the mole ratio of Y₂O₃ (x) is at 0.11–0.54 mol, the (1−x)YVO₄/xY₂O₃:Eu³⁺_0.006,Bi³⁺_0.006 phosphors emit white light by combining the blue, green and orange-red emissions under the excitation of 360–370 nm wavelength which matches the emission of the commercial UV-LED diode. This implies that the phosphors may be the promising white light materials with broad absorption band for white light-emitting diodes.     

Enhancement of oxygen/pressure sensing performance of Eu3+-doped YSZ phosphors via Bi3+ sensitization

The effects of the incorporation of a Bi³⁺ sensitizer on the phosphorescence properties and oxygen partial pressure sensitivity of the Eu³⁺ doped yttria stabilized zirconia (YSZ) phosphors were studied using a lifetime-based optical measurement system. Two series of YSZ: Eu phosphors were investigated in this work: Eu_0.01Bi_xY_0.07-xZr_0.92O_1.96 substitutional series and Eu_0.01Bi_xY_0.07Zr_0.92-xO_1.96-0.5x additive series. The phosphorescence intensity of the additive-series phosphors was enhanced by 47% excited at 405 nm with a Bi³⁺ concentration of 2 mol% due to the energy transfer between Bi³⁺ and Eu³⁺. In contrast, the phosphorescence intensity of the substitutional-series phosphors decreased as the Bi³⁺ concentration increased. The phosphorescence lifetimes for both series phosphors were highly sensitive to oxygen partial pressure at elevated temperatures. With increasing Bi³⁺ concentration, the oxygen sensitivities of both series were enhanced initially, which was related to the increment of concentration dependent non-radiative decay via cross-relaxation between Bi³⁺ and Eu³⁺. With 1 mol% Bi³⁺ doping, the oxygen sensitivity was enhanced by 28% and 12% for substitutional-series and additive-series phosphors, respectively. As the Bi³⁺ concentration further increased, the oxygen sensitivities of both series declined, which was attributed to the energy transfer between Bi³⁺, the formation of Bi³⁺ aggregates as well as the increase of the Eu³⁺ site symmetry. The results of this study not only provided valuable references for phosphor thermometry, but also offered new ideas for developing high-temperature non-contact pressure sensors.     

Color-tunable emissions in Bi3+/Eu3+ activated phosphors for multi-mode optical thermometers

Accurate, self-referential temperature measurements of inaccessible workpieces, bodies in hazardous work environments, or fluids are of tremendous significance. Here, a series of Ca₃Y₂Ge₃O₁₂(CaYGO):1.0%Bi³⁺/yEu³⁺ phosphors were manufactured, which simultaneously presents the characteristic radiation of dopant ions, and the luminescence mechanism was investigated via emission spectroscopy and decay lifetime characterization. Upon excitation at 285 nm, energy transfer (Bi³⁺ → Eu³⁺) of the as-prepared materials exhibited adjustable polychromatic emissions (blue → red). The temperature dependence was evaluated via thermal quenching. The CaYGO phosphors demonstrated a high relative sensitivity of 0.019 K^?1 at 297.8 K according to FIR (the fluorescence intensity ratio) operation rules. Furthermore, temperature-controlled emission spectroscopy displayed a significant chromaticity shift (Δs = 0.05679 for 297.8–480 K). The temperature-dependent lifetime of Eu³⁺ which regarded as a basis of the self-reference measurement provided the maximum relative sensitivity was 0.038%. The excellent signal resolution, high sensitivity values, and results produced by three temperature measurement systems revealed that Ca₃Y₂Ge₃O₁₂: Bi³⁺/Eu³⁺ luminescent materials have excellent development prospects in multi-mode and self-referenced luminous thermometry fields.     

A novel single-phase Na3.6Y1.8(PO4)3:Bi3+,Eu3+ phosphor for tunable and white light emission

A new type of Bi³⁺,Eu³⁺ single- and co-doped Na_3.6Y_1.8(PO₄)₃ phosphate phosphors were manufactured using conventional high-temperature solid-state reaction technique to explore their application for solid-state lighting. The crystal structure, luminescent properties, luminescent mechanism and quantum efficiency were thoroughly explored. Results show that there are two crystallization sites for Bi³⁺ and Eu³⁺ ions. Upon the excitation of 342 and 373 nm, Bi³⁺ single-doped phosphors exhibit green and blue emission, derived from the ³P₁ to ¹S₀ transition of Bi³⁺ located in different occupancy sites. Thanks to radiative energy transfer process from Bi³⁺ to Eu³⁺, adjustable emission could be acquired by altering Eu³⁺ content in co-doped phosphors. Pure white-light emission with quantum efficiency value of 22.9% can be realized in Na_3.6Y_1.8(PO₄)₃:0.01Bi³⁺,0.1Eu³⁺ sample and the integrated intensity of white light emission at 417 K remains 85% of that at room temperature. Our results indicate that Na_3.6Y_1.8(PO₄)₃:Bi³⁺,Eu³⁺ phosphors have feasible application in high-power ultraviolet driven solid-state lighting.     

Effect of crystal structures on energy transfer behavior from Bi3+ to Eu3+ in alkaline earth metalstannates

A single phased color-tunable phosphor via energy transfer has drawn much attention, whereas it is still a question that how to choose a suitable host to realize an efficient energy transfer. In this work, novel single Bi³⁺ or Eu³⁺ doped and Bi³⁺, Eu³⁺ co-activated Ca₂SnO₄ (CSO) and Sr₂SnO₄ (SSO) phosphors have been prepared through a high temperature solid state reaction. The energy transfer happening from hosts to Eu³⁺ has been confirmed. By co-doping of Bi³⁺, a brighter red light is realized which is attributed to the much more efficient energy transfer from Bi³⁺ to Eu³⁺. After comparison, the energy transfer efficiency from Bi³⁺ to Eu³⁺ is much higher in CSO:Bi³⁺, Eu³⁺ than that in SSO:Bi³⁺, Eu³⁺. Furthermore, the experiment reveals that the single-phased color-tunable phosphors exhibit excellent resistance against thermal quenching, suggesting that they can be potential candidates in UV-pumped white light emitting diodes (LEDs).     

Novel color tunable LaCaGaO4:Bi3+,Eu3+ phosphors for high color rendering warm white LEDs

A series of LaCaGaO₄:xBi³⁺,yEu³⁺ (x = 0.002–0.04, y = 0.02–0.45) phosphors with adjustable emission colors were synthesized by high-temperature solid-state reaction. The samples were identified as pure phases by X-ray diffraction and Rietveld refinement, and the crystal structures were analyzed in detail. The LaCaGaO₄:xBi³⁺ phosphor shows an intense blue emission under near-ultraviolet excitation, originating from the ³P₁ → ¹S₀ transition. The spectrum analysis reveals that the Bi³⁺ ions occupy two luminescence centers in the LaCaGaO₄ host and that energy transfer can occur. A model of the energy transfer between the Bi³⁺ and Eu³⁺ ions was also created and studied in detail. As the Eu³⁺-concentration increased, the emission color of the LaCaGaO₄:0.005Bi³⁺,yEu³⁺ phosphor changed from blue to pink to red. In addition, the fluorescence lifetime, quantum yield, thermal stability, and other properties of the phosphors were characterized and analyzed. Finally, two white light-emitting diode devices with R_a values of 96.6 and 95 and correlated color temperatures of 4578 and 3324 K were fabricated, indicating the potential of phosphors for warm white lighting applications.     

Potential red-emitting NaGd(MO4)2:R (M=W,Mo, R=Eu,Sm, Bi) phosphors for white light emitting diodes applications

NaGd(MO₄)₂:R (M=W, Mo, R=Eu³⁺, Sm³⁺, Bi³⁺) phosphors were synthesized by solid-state reaction. The structure and photoluminescence properties of the samples were characterized using X-ray powder diffraction and fluorescence spectrophotometry. The ⁵D₀→⁷F₂ transition of Eu³⁺, which led to a red emission of the phosphors, was dominantly observed in the photoluminescence spectra. The doped Bi³⁺ and Sm³⁺ efficiently sensitized the emission of Eu³⁺ and effectively extended and strengthened the absorption of near-UV light with wavelengths ranging from 395 to 405 nm. In addition, energy transfers from Bi³⁺ to Eu³⁺ and from Sm³⁺ to Eu³⁺ occurred. The chromaticity coordinates of the obtained phosphors were close to the standard values of the National Television Standard Committee (x=0.670, y=0.330). The results suggest that NaGd(WO₄)_2−y(MoO₄)_y:Eu³⁺, Sm³⁺, Bi³⁺ is an efficient red-emitting phosphor for light-emitting diode applications.     

Near-UV light excited Eu3+, Tb3+, Bi3+ co-doped LaPO4 phosphors: Synthesis and enhancement of red emission for WLEDs

A series of single-phase Eu³⁺, Tb³⁺, Bi³⁺ co-doped LaPO₄ phosphors were synthesized by solid-state reaction at 800 °C. Crystal structures of the phosphors were investigated by X-ray diffraction (XRD). A monoclinic phase was confirmed. The excitation (PLE) and emission (PL) spectra showed that the phosphors could emit red light centered at 591 nm under the 392 nm excitation, which is in good agreement with the emission wavelength from near-ultraviolet (n-UV) LED chip (370–410 nm). The results of PLE and PL indicated that the co-doped Tb³⁺ and Bi³⁺could enhance emission of Eu³⁺ and the fluorescent intensities of the phosphors excited at 392 nm could reach to a maximum value when the doping molar concentration of Tb³⁺ and Bi³⁺ is about 2.0% and 2.0%, respectively. The co-doping Tb³⁺ and Bi³⁺ ions can strengthen the absorption of near UV region. They can also be efficient to sensitize the emission of Eu³⁺, indicating that the energy transfer occurs from Tb³⁺ and Bi³⁺ to Eu³⁺ ions. From further investigation it can be found that co-doping Tb³⁺ and Bi³⁺ ions can also induce excitation energy reassignment between ⁵D₀–⁷F₁ and ⁵D₀–⁷F₂ in these phosphors, and result in more energy assignment to ⁵D₀–⁷F₂ emission in LaPO₄:Eu³⁺, Tb³⁺, Bi³⁺. Our research results displayed that La_0.94PO₄:Eu³⁺_0.02, Tb³⁺_0.02, Bi³⁺_0.02 could be a new one and could provide a potential red-emitting phosphor for UV-based white LED.     

Enhanced luminescence properties of Eu3+ in La2MoO6 by nonsensitization of Bi3+

It was unusual for Bi³⁺ ions to enhance the emission intensity of phosphors via nonsensitization. Here, La₂MoO₆:Eu³⁺, Bi³⁺ phosphors were successfully synthesized by a high temperature solid-state reaction method in air atmosphere. As the increase of doping concentration of Bi³⁺, the emission spectra of La₂MoO₆:Eu³⁺, Bi³⁺ phosphors had obvious shifts, splits and the enhancement of intensities, which indicated that the characteristics of the phosphors were modified. To analyze these phenomena, the crystal structure refinements, spectral characteristic analyze and Judd-Ofelt theoretical calculation were mainly performed. Bi³⁺ ions played the role of the nonsensitizer and affected the distortion of the crystal, the sites of Eu³⁺ ions, the field splitting energy and the internal quantum yield. Moreover the nephelauxetic effects of Bi³⁺ ions and the ET process caused synergistically the life times of La₂MoO₆:Eu³⁺, Bi³⁺ phosphors to increase and then gradually decrease. The CIE coordinates of phosphors changed within a small range. This study might be instrumental in promoting the further application of Bi³⁺ ions in rare earth luminescent materials.     

A novel Eu2+/Tb3+ co-doped phosphor with pyroxene structure applied for cryogenic thermometric sensing

Pyroxene-type phosphors were widely developed due to the advantages of high chemical stability, luminous efficiency, and low production cost. In this contribution, a series of Eu²⁺/Tb³⁺ co-doped Ca_0.75Sr_0.2Mg_1.05Si₂O₆ (CSMS) phosphors with pyroxene structure were successfully synthesized by the solid-state method. Under the 340 nm excitation, the emission peaks of the phosphor show a redshift with the increase of Eu²⁺ concentration. The emitting color of Eu²⁺/Tb³⁺ co-doped samples shows a redshift attributed to the energy transfer from Eu²⁺ to Tb³⁺. Simultaneously, acquired thermometer exposes superbly temperature-sensitive properties (S_a and S_r having maximum values 4.7% K⁻¹ and 0.6% K⁻¹, respectively) over the cryogenic temperature range (77–280 K). Furthermore, it has good stability and precision at cryogenic temperatures, indicating that CSMS:0.03Eu²⁺/0.03Tb³⁺ phosphor is a very promising fluorescent material suitable for cryogenic temperature sensing.     

Preparation and luminescent modulation of KGaSiO4:Eu3+ phosphors using for multiple anti-counterfeiting

Anti-counterfeiting technology is of great significance to information security. To obtain high-quality anti-counterfeiting materials, the developments of inorganic materials are crucial. In this paper, a series KGaSiO₄:xEu³⁺ phosphors with persistent luminescence, photoluminescence, and thermochromic have been successfully prepared and the application of quadruple anti-counterfeiting is realized. The X-ray diffraction and Rietveld refinement indicate that the phosphors are pure phase. With Eu³⁺ ions doping, the structure change, site occupancies, and color-tunable phenomenon are carefully investigated. Different from another Eu³⁺ doping phosphor, the emission of KGaSiO₄:0.2% Eu³⁺ phosphor changes with the excitation light in the region of 240 nm–306 nm. The emission color can be modulated with the surrounding temperature. Surprisingly, this phosphor can emit green afterglow light, which is attributed to the different luminescent properties of the matrix and doping of Eu³⁺ ions. The series of phosphors exhibit abundant luminescent properties. Based on their wavelength dependence, concentration quenching, long afterglow, and thermochromic properties, the KGaSiO₄:xEu³⁺ phosphors can be effective materials for quadruple-modal anti-counterfeiting devices.     

Na2GdMg2V3O12:Sm3+ phosphors for three-mode optical temperature sensing

Multi-mode optical thermometry is emerging as a promising technique for accurate temperature measurement. Here, a series of Na₂GdMg₂V₃O₁₂:Sm³⁺ (NGMVO:xSm³⁺) phosphors with dual-emission centers were successfully elaborated. Irradiated by 349 nm light, NGMVO:Sm³⁺ can generate emissions from VO₄³⁻ and Sm³⁺ simultaneously due to energy transfer between them. Benefitting from difference of thermal quenching performance of two luminescent centers, fluorescence intensity (FI), fluorescence intensity ratio (FIR), and Commission Internationale de L'Eclairage coordinate modes of NGMVO:Sm³⁺ thermometer were designed. Maximum relative sensitivities (S_R) are found to be as high as 2.21 %K⁻¹, 2.12 %K⁻¹, and 0.244 %K⁻¹, respectively. Besides, with temperature increasing, S_R values of FI and FIR modes decrease slowly. Their minimal S_R values between 303 and 513 K maintain above 1.36 %K⁻¹ and 1.08 %K⁻¹, respectively. Our findings reveal that NGMVO:Sm³⁺ phosphors have promising applications for multimode temperature senor.