基于弯曲压杆的光纤光栅可调谐线性啁啾化

提出利用镍钛合金压杆弯曲应变引入到光纤布拉格光栅(fiber Bragg grating,FBG)实现无中心波长漂移可调谐线性啁啾化方法并进行了实验验证。设计一种镍钛合金压杆结构,理论计算并有限元分析验证了应变分布情况。将光纤光栅粘贴在镍钛合金压杆上,弯曲压杆将线性拉伸与压缩应变引入到栅区,利用光谱仪记录反射谱。实验结果表明,当压杆移动距离达到12.5 mm时,反射谱带宽增大到1.57 nm,中心波长漂移量仅为0.11 nm。利用光纤光栅啁啾化理论,结合传输矩阵法和龙格库塔法实现啁啾光纤光栅光谱重构。实验结果与仿真结果吻合。该方法制作的啁啾光栅可以实现带宽可调谐且基本无中心波长漂移,在光纤传输和传感领域均具有一定的应用前景。     

一种新型光纤光栅波长与带宽独立调谐的方法

提出了一种新型的光纤光栅的中心波长与带宽独立调谐的方法。将光纤布拉格光栅(FBG)粘贴于圆环形薄壁截面梁的外表面,通过旋转圆环形薄壁截面梁,即相当于改变光纤光栅的位置来实现中心波长与带宽的独立调谐。实验上得到了6.706 nm准无啁啾的中心波长调谐和5.368 nm的准无中心波长漂移的最大带宽调谐,并且此中心波长和带宽调谐均与拉力呈线性关系,实验结果与理论分析一致。     

基于悬臂梁啁啾调谐的光纤光栅滤波器

提出并发展了一种基于悬臂梁结构的啁啾光纤Bragg光栅(CFBG)啁啾调谐方案,获得了一系列性能优异的可调谐CFBG滤波器,包括调谐范围达到36 nm(1.8～37.8 nm)的带宽可变反射滤波器、色散在178～2 100ps/nm范围内可调的色散补偿器、基于取样CFBG或重叠写入CFBG的信道间隔可调谐滤波器等。这些FBG滤波器不但能维持较高的反射率,还能保持中心波长基本不变。     

利用悬臂梁将均匀周期光纤光栅变为啁啾光纤光栅

利用均质、等厚及等腰梯形的悬臂梁,对刚性粘贴其表面的光纤光栅的布喇格反射中心波长在1557．68～1564．2nm范围内进行了线性调谐,同时带宽为外0.52nm的均匀周期的光纤光栅被调谐成带宽为2．52nm的啁啾光栅,且啁啾量可调。随着带宽的增加,反射谱的峰值功率呈减弱的趋势。     

一种闭环控制的光纤光栅动态色散补偿仪

利用啁啾光纤光栅的应变调谐特性，将色散补偿的啁啾光纤光栅斜贴于悬臂梁的侧面，通过应力实现啁啾量调整而改变其色散补偿量的大小，同时利用固定在同一悬臂梁的均匀布拉格光栅传感器，实现了闭环自动控制色散补偿量，研制出了一种新型的光纤光栅动态色散补偿仪。该色散补偿仪工作在1550nm波段，典型性能数据为：色散动态补偿范围-1000-1680ps／nm，插入损耗小于1．5dB，动态调谐步进响应时间小于50ms，基本上能满足10Gb／s光纤通信系统中色散动态补偿的要求。     

宽带可调谐光纤光栅色散补偿器系统设计

文章提出一种在光纤光栅自身热膨胀效应产生啁啾的基础上,利用铝片热膨胀系数比较高的特点产生应力来增强光纤光栅啁啾,从而实现了宽带、大范围色散调谐的新型光纤光栅色散补偿器。该色散补偿器能够分别对群速度色散及中心波长独立调谐。实验结果表明,在中心波长为1 551.25nm处,能够实现>1.5nm的色散补偿带宽,-350～-690ps/nm的群时延色散调谐范围;在色散为-660ps/nm情况下,能够实现中心波长1nm的偏移。     

60 km色散补偿8×50 GHz光纤光栅梳状滤波器设计

设计了一种新颖的60km色散补偿8信道50GHz信道间隔的啁啾光纤Bragg光栅(CFBG)梳状滤波器。采用基于LP算法的IS光纤光栅设计技术,设计出CFBG的折射率调制函数和啁啾分布。根据设计得出的耦合系数分布,采用传输矩阵法分析所设计CFBG的反射谱、时延曲线和群时延抖动。结果表明,所设计的CFBG不仅满足了设计指标要求,性能优良,而且在已知的制作技术条件下可以实现。     

啁啾光纤光栅EDFA增益平坦滤波器的设计与制作

采用啁啾相位掩膜板和程控扫描曝光技术,在经过载氢增敏处理的普通单模光纤上制作出可以用于掺铒光纤放大器(EDFA)增益谱平坦化的啁啾光纤布喇格光栅(CFBG)型增益平坦滤波器(GFF),运用数值解析的方法得到曝光量曲线,并将之分解成曝光频率、曝光功率密度、光斑尺寸和光纤移动速度的曝光函数,按照曝光函数进行程控扫描曝光从而精确控制光栅的反射率.对制作的CFBG进行退火老化处理和温度补偿及保护封装,封装后GFF的温漂系数在-20～ 70 ℃内变化小于1 pm/℃,经平坦后的EDFA增益谱在30 nm带宽范围内,不平坦度＜±0.3 dB.根据不同的EDFA的ASE谱,可程控给出不同的曝光函数,以制作具有不同反射谱的CFBG型GFF.     

光纤光栅动态色散补偿技术的研究

本文在研究了啁啾光纤光栅的可调谐特性基础上,利用啁啾光纤光栅的应变调谐特性,通过固定在同一悬臂梁的均匀Bragg光栅传感器,实现了闭环自动控制色散补偿量,研制出了一种新型的光纤光栅动态色散补偿系统,并将研制的动态色散补偿系统成功地应用于光传输系统,获得了很好的结果.     

高斯脉冲在光纤中传输的光纤光栅色散补偿研究

高斯脉冲在光纤中传输一段距离后，啁啾系数和脉冲宽度均要发生变化，不同啁啾系数和脉冲宽度的高斯脉冲经过啁啾光纤光栅反射后的脉宽压缩特性也不同。本文介绍了啁啾高斯脉冲在光纤中的传输特性以及啁啾高斯脉冲经啁啾光纤光栅反射后的传输特性。理论分析和实验均表明，使用啁啾光纤光栅实现长距离色散补偿时，最佳色散补偿长度与光栅位置有关。     

Self-seeding of Fabry-Perot laser diode for generating wavelength-tunable chirp-compensated single-mode pulses with high-sidemode suppression ratio

We report an effective technique for generating wavelength-tunable chirp-compensated single-mode pulses with a high sidemode suppression ratio (SMSR) based on self-seeding a Fabry-Perot laser diode. This technique relies on the use of a tunable linearly-chirped fiber Bragg grating to provide wavelength-selective feedback, output filtering, and chirp compensation. With this technique, we have generated chirp-compensated picosecond pulses with a SMSR higher than 40 dB over a tuning range of 11.5 nm.     

Tunable dispersion device based on a tapered fiber Bragg grating and nonuniform magnetic fields

We present a new variable dispersion device based on tuning the chirp of a tapered fiber Bragg grating by means of a magnetic transducer. By using a nonuniform magnetic field, we demonstrate a 188-472-ps/nm dispersion tuning range, suitable for tunable radio-frequency filters and dispersion compensation, among others.     

Tunable fiber Bragg grating filters realized by chirp rate tuning with a cantilever beam

An efficient scheme to change the chirp rate of a fiber Bragg grating (FBG) has been developed based on a specially-designed cantilever beam with the beam-bending method. It allows, to date, the largest tuning range of 36 nm in reflection bandwidth of a chirped-FBG (CFBG) while keeping the center wavelength nearly fixed during the tuning process. Using this method, bandwidth-tunable fiber grating filters with tunable chromatic dispersion or differential group delay have been demonstrated. Channel spacing-tunable multi-wavelength filters based on both sampled- and superimposed-CFBGs have also been realized. Moreover, tuning of the bandwidth and channel spacing is continuous with this scheme that makes the achieved devices more flexible.     

Linear and Gaussian Chirped Fiber Bragg Grating and Its Applications in Fiber-Optic Filtering and Sensing Systems

A novel technique for continuous chirp control of a fiber Bragg grating (FBG) based on a double-hole cantilever beam (DHCB) is proposed and experimentally demonstrated. The specifically designed DHCB provides a pressure-position-dependent strain-gradient along an originally uniform FBG and allows a tunable linear and Gaussian chirp modulation over the grating spectrum. Bandwidth and wavelength-independent tuning, under center-applied-pressure effect, is achieved by linear chirp modulation with a symmetrical broadening profile and a temperature-controlled wavelength shift. And intensity-referenced temperature-immune pressure measurement, under side-applied-pressure effect, is accomplished by Gaussian chirp modulation with a single-side-broadening profile and a linear-increasing reflection optical power.     

Dynamic responses of widely tunable sampled grating DBR lasers

The modulation bandwidth, dynamic mode suppression ratio, and wavelength chirp of directly modulated sampled grating DBR lasers have been measured. Although the tuning range can be up to an order of magnitude larger than in simple DBR lasers, the chirp is about the same or better over a wide range of operation parameters. The modulation bandwidth was in excess of 4 GHz and the dynamic MSR remained larger than 40 dB as long as the current did not swing below threshold. The linewidth enhancement factor was extracted from the measured chirp parameters and ranged from three to eight for different lasing wavelengths of the tunable lasers. The dispersion of the linewidth enhancement factor is consistent with published theoretical predictions.     

基于重叠光栅和啁啾光栅的双波长光纤激光器

研究光寻址电位传感器(LAPS)的器件噪声特性 。通过对LAPS半导体场效应器件的结构分析,建 立LAPS的理论模型,并进一步分析LAPS器件噪声信号的来源、种类及特性。以 pH缓冲液中H离子 浓度为检测对象,搭建基于NI采集卡和Labview环境的LAPS测试系统,对影响LAPS信号噪声 特性的光源 波长、光源调制频率、光源强度和Si衬底厚度等因素进行了仿真和实验研究。结果表明,增 大光源波长和光源强度 是提高输出信号幅值和信噪比(SNR)的最有效方法。     

Fabrication of chirped fiber grating with adjustable chirp andfixed central wavelength

We theoretically analyze and experimentally demonstrate a simple method for adjusting the chirp of chirped fiber gratings by temperature, while the central wavelength is temperature insensitive. Chirped fiber grating with tapered cross-section area is mounted under tension in a negative thermal-expansion coefficients material. The central wavelength is determined by the tension, and almost does not vary with temperature after packaging. The chirp can be adjusted by temperature. The grating in the package exhibits a linear variation in chirp of -0.00051 nm/cm/°C, and the temperature coefficient of central wavelength is -0.0018 nm/°C     

Measurements on competition between carrier-induced and thermally-induced wavelength tuning in ridge waveguide DBR lasers

The tuning characteristics of ridge waveguide DBR lasers have been measured under CW and pulsed grating currents. Under CW grating current injection, a maximum tuning range of 2.5 nm was measured. This tuning range was extended to almost 7 nm under pulsed conditions. The increase in the tuning range is explained by the absence of thermal tuning mechanisms for pulsed grating currents and the dominance of thermal tuning in the ridge waveguide structure at large CW grating currents is explicitly shown.<>     

Single-drive LiNbO/sub 3/ Mach-Zehnder modulator with widely DC tunable chirp

We present a 10-Gb/s LiNbO/sub 3/ Mach-Zehnder modulator that allows tuning of the chirp in a wide range (-0.7/spl divide/0.7) by applying just a dc voltage, while the radio-frequency section is single drive. The device shows uniform performances across the chirp tuning range. By tuning chirp value, transmission tests showed power penalty less than 2 dB for spans up to 2100 ps/nm.     

SGDBR激光器中取样光栅的理论和实验研究

讨论了取样光栅分布布拉格反射激光器(SGDBR)中取样光栅对激光器调谐范围、输出功率和光谱质量的影响,介绍了其设计流程,并据此对SGDBR进行了实验研究.其取样光栅的反射谱和设计相符,且在30nm准连续调谐范围内边模抑制比都大于30dB.