Phase Relations in the System Bi2O3-WO3

Phase relations in the system Bi₂O₃-WO₃ were studied from 500° to 1100°C. Four intermediate phases, 7Bi₂O₃· WO₃, 7Bi₂O₃· 2WO₃, Bi₂O₃· WO₃, and Bi₂O₃· 2WO₃, were found. The 7B₂O · WO₃ phase is tetragonal with a ₀= 5.52 Å and c ₀= 17.39 Å and transforms to the fcc structure at 784°C; 7Bi₂O₃· 2WO₃ has the fcc structure and forms an extensive range of solid solutions in the system. Both Bi₂O₃· WO₃ and Bi₂O₃· 2WO₃ are orthorhombic with (in Å) a ₀= 5.45, b ₀=5.46, c ₀= 16.42 and a ₀= 5.42, b ₀= 5.41, c ₀= 23.7, respectively. Two eutectic points and one peritectic exist in the system at, respectively, 905°± 3°C and 64 mol% WO₃, 907°± 3°C and 70 mol% WO₃, and 965°± 5°C and 10 mol% WO₃.     

Grain Growth in Sintered ZnO and ZnO-Bi2O3 Ceramics

Grain growth in a high-purity ZnO and for the same ZnO with Bi₂O₃ additions from 0.5 to 4 wt% was studied for sintering from 900° to 1400°C in air. The results are discussed and compared with previous studies in terms of the phenomenological kinetic grain growth expression: G ⁿ— G ⁿ₀= K ₀ t exp(— Q/RT ). For the pure ZnO, the grain growth exponent or n value was observed to be 3 while the apparent activation energy was 224 ± 16 kJ/mol. These parameters substantiate the Gupta and Coble conclusion of a Zn²⁺ lattice diffusion mechanism. Additions of Bi₂O₃ to promote liquidphase sintering increased the ZnO grain size and the grain growth exponent to about 5, but reduced the apparent activation energy to about 150 kJ/mol, independent of Bi₂O₃ content. The preexponential term K ₀ was also independent of Bi₂O₃ content. It is concluded that the grain growth of ZnO in liquid-phase-sintered ZnO-Bi₂O₃ ceramics is controlled by the phase boundary reaction of the solid ZnO grains and the Bi₂O₃-rich liquid phase.     

Grain Growth of ZnO during Bi2O3 Liquid-Phase Sintering

Grain growth of ZnO during the liquid-phase sintering of binary ZnO–Bi₂O₃ ceramics has been studied for Bi₂O₃ contents from 3 to 12 wt% and sintering from 900° to 1400°C. The results are considered in combination with previously published studies of ZnO grain growth in the ZnO–Bi₂O₃ system. For the Bi₂O₃ contents of the present study, the rate of ZnO grain growth is found to decrease with increasing Bi₂O₃. Activation analysis, when combined with the results of similar analyses of the previous studies, reveals a change in the rate-controlling mechanism for ZnO grain growth. Following a low-Bi₂O₃-content region of nearly constant activation energy values of about 150 kJ/mol, further Bi₂O₃ additions cause an increase of the activation energy to about 270 kJ/mol. consistent with accepted models of liquid-phase sintering, it is concluded that the rate-controlling mechanism of ZnO grain growth during liquid-phase sintering in the presence of Bi₂O₃ changes from one of a phase-boundary reaction at low Bi₂O₃ levels to one of diffusion through the liquid phase at about the 5 to 6 wt% Bi₂O₃ level and above.     

Interdiffusion and Association Phenomena in the System NiO-Al2O3

The rate of formation of NiAl₂O₄ by reaction between single crystals of NiO and Al₂O₃ can be described by k = 1.1 × 10⁴ exp (−108,000 ± 5,000/ RT ) cm²/s. In NiO the behavior of D as a function of concentration supports the Lidiard theory of diffusion by impurity-vacancy pairs. A good fit of the theory to the experimental results was obtained by assuming that Al³⁺ ions diffuse as [Al_Ni· V_Ni]'pairs. The diffusion coefficient of pairs, D_p , obeys the equation 6.6 × 10⁻² exp (−54,000 ± 3,000/ RT ) cm²/s. The free energy of association for pairs was calculated to range from 6.5 kcal/mol at 1789°C to 9.0 kcal/mol at 1540°C. The interdiffusion coefficients in the spinel showed a constant small increase with increasing concentration of Al³⁺ dissolved in the spinel.     

Phase Relations In The Pseudo-Ternary System La2O3–SrO–Fe2O3

The phase relations in the pseudo-ternary system La₂O₃–SrO–Fe₂O₃ have been investigated in air. Isothermal sections at 1100° and 1300°C are presented based on X-ray diffraction and thermal analysis of annealed samples. Extended solid solubility was observed for the compounds Sr _{n +1− v} La _v Fe _n O_{3 n +1−δ} ( n =1, 2, 3, and ∞) and Sr_{1− x} La _x Fe₁₂O₁₉, while only limited solubility of La in Sr_{4− z} La _z Fe₆O_13±δ was observed. At high Fe₂O₃ content, a liquid with low La₂O₃ content was stable at 1300°C.     

Phase Equilibria in the Ga2O3In2O3 System

Subsolidus phase relationships in the Ga₂O₃–In₂O₃ system were studied by X-ray diffraction and electron probe microanalysis (EPMA) for the temperature range of 800°–1400°C. The solubility limit of In₂O₃ in the β-gallia structure decreases with increasing temperature from 44.1 ± 0.5 mol% at 1000°C to 41.4 ± 0.5 mol% at 1400°C. The solubility limit of Ga₂O₃ in cubic In₂O₃ increases with temperature from 4.X ± 0.5 mol% at 1000°C to 10.0 ± 0.5 mol% at 1400°C. The previously reported transparent conducting oxide phase in the Ga-In-O system cannot be GaInO₃, which is not stable, but is likely the In-doped β-Ga₂O₃ solid solution.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Phase Equilibria in the Spinel Region of the System FeO-Fe2O3-Al2O3

Phase relations in the spinel region of the system FeO-Fe₂O₃-Al₂O₃ were determined in CO₂ at 1300°, 1400°, and 15000°C and for partial oxygen pressures of 4 × 10⁻⁷ and 7 × 10⁻¹⁰ atmospheres at 15OO°C. The spinel field extends continuously from Fe₃O_4-x to FeAl₂O_4+z.     

Stability of Bi2Sr2Ca1Cu2O8 ±δ Thick Films at Elevated Oxygen Pressures and Temperatures

Bi₂Sr₂Ca₂Cu₂O_8±δ-type compound thick films were exposed to oxygen-argon-gas mixtures (1% to 20% oxygen gas) at elevated pressures (up to 207 MPa) and temperatures (500° to 940°C) for times ranging from 5 to 96 h. At a sufficiently high oxygen fugacity and temperature, Bi₂Sr₂Ca₁Cu₂O_8±δ decomposed via a solid-state reaction. Room-temperature X-ray diffractometry and electron probe microanalysis of decomposed films revealed the presence of Bi₂(Sr,Ca)₂-Cu₁O_6±θ ro-type compound, Bi₂Sr₂,Ca₁O_8±δ-type compound, and CuO. Bi₂Sr₂Ca₁Cu₂O_8±δ decomposition was accompanied by a modest weight gain, which was consistent with an oxidation reaction. The solid-state decomposition reaction could be reversed by heat treatment of decomposed films at 860°C in pure, flowing oxygen at ambient pressure.     

Phase Equilibria in the Systems CaO–CuO and CaO-Bi2O3

New data are presented on the phase equilibria of the binary systems CaO-CuO and CaO-Bi₂O₃. Corrected compositions are reported for Ca.Bi₆O₁₃ and Ca₂Bi₂O₅ and a new metastable high-temperature phase is reported for a composition near Ca₆Bi₇O_16.5. The composition and decomposition temperatures for Ca_1–x.CuO₂ are given for both air and 1 atm of oxygen at 755 ± 5° and 835 ± 5°C, respectively.     

Phase Relations in the System Fe2O3–Fe3O4–YFeO3 in Air

Measurements were made of temperature and ternary composition for coexisting liquid and crystalline phases on the air isobar in the system Fe₂O₃-Fe₃O₄-YFeO₃ with particular regard to the stability range and compositional limits of yttrium iron garnet. Phase equilibrium relations were determined by conventional quenching techniques combined with measurements of loss in weight at the reaction temperature to locate true ternary compositions. The intersection of the air isobar with the ternary univariant boundary curve for coexisting magnetite, garnet, and liquid phases results in a eutectic-type situation at the composition Y_0.27Fe_1.73 O_2.87 and 1469°± 2°C. A similar intersection of the isobar with the boundary curve for coexisting garnet, orthoferrite, and liquid phases gives rise to a peritectic-type reaction at 1555° 3°C. and Y_0.44Fe_1.56 O_2.89 The yttrium iron garnet crystallizing from liquids within these temperature and composition limits contains up to 0.5 mole % iron oxide in excess of the stoichiometric formula in terms of the starting composition 37.5 mole % Y₂O₃, 62.5 mole % Fe₂O₃. At 1470° C. the garnet phase in equilibrium with oxide liquid contains 2 mole % FeO in solid solution. The small solubility of excess of iron oxide and partial reduction of the garnet phase in air are unavoidable during equilibrium growth from the melt.     

Electrical Properties of Sr0.7Ba0.3TiO3 Ceramics Doped with Nb2O5, 3Li2O · 2SiO2, and Bi2O3

The electrical properties of Sr_0.5Ba_0.3TiO₃ in the presence of Nb₂O₅ as a donor, 3Li₂O · 2SiO₂ as a sintering agent, and Bi₂O₃ as a dopant have been studied. When the compositions of the ceramics were 1 mol Sr_0.7Ba_0.3TiO₃+ 0.5 mol% Nb₂O₅+ 2 mol% 3Li₂O · 2SiO₂+ 0.2 mol% Bi₂O₃, the ceramics were sintered at 1100°C and exhibited the following characteristics: apparent dielectric constant ɛ, 25000; loss factor tan δ, 2%; insulating resistivity ρ_j, 10¹⁰Ω· cm; variation of dielectric constant with temperature Δɛ/ɛ (−25° to +85°C), +10%, −14%. ɛ and tan δ show only small changes with frequency. The study shows this ceramic can be used in multilayer technology.     

Grain Growth of ZnO in ZnO-Bl2O3 Ceramics with Ai2O3 Additions

Grain growth of ZnO during liquid-phase sintering of a ZnO-6 wt% Bi₂O₃ ceramic was investigated for A1₂O₃ additions from 0.10 to 0.80 wt%. Sintering in air for 0.5 to 4 h at 900° to 1400°C was studied. The AI₂O₃ reacted with the ZnO to form ZnAl₂O₄ spinel, which reduced the rate of ZnO grain growth. The ZnO grain-growth exponent was determined to be 4 and the activation energy for ZnO grain growth was estimated to be 400 kJ/mol. These values were compared with the activation parameters for ZnO grain growth in other ceramic systems. It was confirmed that the reduced ZnO grain growth was a result of ZnAl₂O₄ spinel particles pinning the ZnO grain boundaries and reducing their mobility, which explained the grain-growth exponent of 4. It was concluded that the 400 kJ/mol activation energy was related to the transport of the ZnAl₂O₄ spinel particles, most probably controlled by the diffusion of O^2- in the ZnAl₂O₄ spinel structure.     

X-Ray Study of the Solid Solution of TiO, Fe2O3, and G, O3 in Mullite (3A12O3a2Si02)

A study of the solid solution of TiO₂, Fe₂O₃, and Cr₂0₃ in mullite was made by measuring the changes in lattice parameters and unit-cell volume. Synthetic mullite (3O₃-2SiO₂) was reacted with up to 12 weight % of the oxides at temperatures ranging from 1000° to 17000C. The approximate minimum temperature required for the formation of solid solution was 12000C. for Fe₂0₃ and 1400°C. for Cr₂O₃ and TiO₃. The maximum amount of solid solution found was 2 to 4% TiO₂ at 1600°C., 10 to 12% Fe₂O_s at 1300°C., and 8 to 10% Cr_ZO₃ at 1600OC. Lattice parameters and unit-cell volumes for each solid solution series increased with increasing amounts of foreign oxide. There was good agreement between the calculated and observed increase in cell dimensions for the iron oxide series. Except in the case of titania, there was good agreement between X-ray data and petrographic observations.     

The Bi2O3–Nb2O5–NiO Phase Diagram

The Bi₂O₃–Nb₂O₅–NiO phase diagram at 1100°C was determined by means of solid-state synthesis, X-ray diffraction, and scanning electron microscopy. A ternary eutectic with a melting point below 1100°C was found to exist in the field between NiO, Bi₂O₃, and the end-member of the δBi₂O₃–Nb₂O₅ solid solution. The existence of the previously reported Bi₃Ni₂NbO₉ phase was disproved. A pyrochlore homogeneity range around Bi_1.5Ni_0.67Nb_1.33O_6.25 was determined together with all the phase relations in this phase diagram.     

Subsolidus Reactions in the System Fe2O3- TiO2

A study has been made of the binary system Fe₂O₂-TiO₂ by solid-state reactions under dry and hydrothermal conditions. Under dry conditions only one binary compound, pseudobrookite (Fe₂O₃-TiO₂), was formed and no evidence of solid solution on either side of this compound at temperatures up to 1200°C. was obtained. The system under these conditions is a simple binary with a single binary compound. Under hydrothermal conditions of 300° C. and 1200 Ib. per sq. in. the system is apparently also binary, with a single unstable compound closely resembling, if not identical with, the naturally occurring mineral arizonite (ferric metatitanate, Fe₂(TiO₃)₃).     

Crystallization and Properties of Fe2O3—CaO—SiO2 Glasses

Nucleation and crystal growth rates and properties were studied in a two-stage heat treatment process for Fe₂O₃-CaO-SiO₂ glasses. Glass transition (T_g) and crystallization temperatures (T _c ) for the glasses lay between about 612.0° and 710.0°C, and 858.5° and 905.0°C, respectively, and magnetite was the main crystal phase. For a glass of 40Fe₂O₃. 20CaO·40SiO₂ (in wt%) the maximum nucleation rate was (68.6 ± 7) × 10⁶/mm³·s at 700°C, and the maximum crystal growth rate was 9.0 nm/min^1/2 at 1000°C. The mean crystal size of the magnetite increased from 30 to 140 nm with variation of nucleation and crystal growth conditions. The glass showed the maxima in saturation magnetization and coercive force, 212.1 × Wb/m² and 30.8 × 10³ A/m, when heat-treated for 4 h at 1000°C and 1050°C, respectively. The variation of the saturation magnetization could be quantitatively interpreted well in terms of the volume fraction of the magnetite, whereas that of the coercive forces could be explained only qualitatively in terms of the particle size of the magnetite. Hysteresis losses showed the maximum value of 1493 W/m³ when heat-treated at 1000°C for 4 h prenucleated at 700°C for 60 min, and increased linearly with increasing heat treatment time under a magnetic field up to 800 × 10³ A/m.     

Spray Pyrolysis of Fe3O4–BaTiO3 Composite Particles

Fe₃O₄–BaTiO₃ composite particles were successfully prepared by ultrasonic spray pyrolysis. A mixture of iron(III) nitrate, barium acetate and titanium tetrachloride aqueous solution were atomized into the mist, and the mist was dried and pyrolyzed in N₂ (90%) and H₂ (10%) atmosphere. Fe₃O₄–BaTiO₃ composite particle was obtained between 900° and 950°C while the coexistence of FeO was detected at 1000°C. Transmission electron microscope observation revealed that the composite particle is consisted of nanocrystalline having primary particle size of 35 nm. Lattice parameter of the Fe₃O₄–BaTiO₃ nanocomposite particle was 0.8404 nm that is larger than that of pure Fe₃O₄. Coercivity of the nanocomposite particle (390 Oe) was much larger than that of pure Fe₃O₄ (140 Oe). These results suggest that slight diffusion of Ba into Fe₃O₄ occurred.     

Microwave Dielectric Properties of Low Firing Temperature Bi2W2O9 Ceramics

Phase stability, sinterability, and microwave dielectric properties of Bi₂W₂O₉ ceramics and their cofireability with Ag, Cu, and Au electrodes have been investigated. Single-phase Bi₂W₂O₉ powder was synthesized by solid-state reaction in air at 800°C for 3 days. X-ray powder diffraction data show Bi₂W₂O₉ to have an orthorhombic crystal structure described by the noncentrosymmetric space group Pna 2₁, with lattice parameters a =5.4401(8), b =5.4191(8), c =23.713(4) Å. Ceramics fired at temperatures up to 865°C remain single-phase but above this temperature ferroelectric Bi₂WO₆ appears as a secondary phase. The measured relative permittivity of Bi₂W₂O₉ ceramics increases continuously from 28.6 to 40.7 for compacts fired between 860° and 885°C. The bulk relative permittivity of Bi₂W₂O₉ corrected for porosity was calculated as 41.3. Bi₂W₂O₉ ceramics fired up to 875°C exhibit moderate quality factors, Q × f _r, ∼7500–7700 GHz and negative temperature coefficient of resonant frequency, ∼−54 to −63 ppm/°C. Chemical compatibility experiments show Bi₂W₂O₉ ceramics to react with both Ag and Cu electrodes, but to form good contacts with Au electrodes.     

High-Temperature Phase Relations in the Sc2O3-Ta2O5 System

The phase relations for the Sc₂O₃-Ta₂O₅ system in the composition range of 50-100 mol% Sc₂O₃ have been studied by using solid-state reactions at 1350°, 1500°, or 1700°C and by using thermal analyses up to the melting temperatures. The Sc_5.5Ta_1.5O₁₂ phase, defect-fluorite-type cubic phase (F-phase, space group Fm 3 m ), ScTaO₄, and Sc₂O₃ were found in the system. The Sc_5.5Ta_1.5O₁₂ phase formed in 78 mol% Sc₂O₃ at <1700°C and seemed to melt incongruently. The F-phase formed in ∼75 mol% Sc₂O₃ and decomposed to Sc_5.5Ta_1.5O₁₂ and ScTaO₄ at <1700°C. The F-phase melted congruently at 2344°± 2°C in 80 mol% Sc₂O₃. The eutectic point seemed to exist at ∼2300°C in 90 mol% Sc₂O₃. A phase diagram that includes the four above-described phases has been proposed, instead of the previous diagram in which those phases were not identified.